MPLS-LDP-FRAME-RELAY-STD-MIB: View SNMP OID List / Download MIB

VENDOR: INTERNET-STANDARD


 Home MIB: MPLS-LDP-FRAME-RELAY-STD-MIB
Download as:   
SNMPv2-CONF, MPLS-LDP-STD-MIB, FRAME-RELAY-DTE-MIB, SNMPv2-SMI, MPLS-TC-STD-MIB, IF-MIB, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 mplsLdpFrameRelayStdMIB 1.3.6.1.2.1.10.166.6
Copyright (C) The Internet Society (year). The initial version of this MIB module was published in RFC 3815. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB contains managed object definitions for configuring and monitoring the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP), utilizing Frame Relay as the Layer 2 media.
     mplsLdpFrameRelayObjects 1.3.6.1.2.1.10.166.6.1
         mplsLdpEntityFrameRelayObjects 1.3.6.1.2.1.10.166.6.1.1
             mplsLdpEntityFrameRelayTable 1.3.6.1.2.1.10.166.6.1.1.1 no-access
This table contains Frame Relay specific information which could be used in the 'Optional Parameters' and other Frame Relay specific information. This table 'sparse augments' the mplsLdpEntityTable when Frame Relay is the Layer 2 medium.
                 mplsLdpEntityFrameRelayEntry 1.3.6.1.2.1.10.166.6.1.1.1.1 no-access
An entry in this table represents the Frame Relay optional parameters associated with the LDP entity.
                     mplsLdpEntityFrameRelayIfIndexOrZero 1.3.6.1.2.1.10.166.6.1.1.1.1.1 interfaceindexorzero read-only
This value represents either the InterfaceIndex of the 'ifLayer' where the Frame Relay Labels 'owned' by this entry were created, or 0 (zero). The value of zero means that the InterfaceIndex is not known. For example, if the InterfaceIndex is created subsequent to the Frame Relay Label's creation, then it would not be known. However, if the InterfaceIndex is known, then it must be represented by this value. If an InterfaceIndex becomes known, then the network management entity (e.g., SNMP agent) responsible for this object MUST change the value from 0 (zero) to the value of the InterfaceIndex. If an Frame Relay Label is being used in forwarding data, then the value of this object MUST be the InterfaceIndex.
                     mplsLdpEntityFrameRelayMergeCap 1.3.6.1.2.1.10.166.6.1.1.1.1.2 integer read-only
This represents whether or not the Frame Relay merge capability is supported. This is the EXACT value for the Frame Relay Session Parameter, field M (for Frame Relay Merge Capabilities). The Frame Relay Session Parameter is an optional parameter in the Initialization Message. The description from rfc3036.txt is: 'M, Frame Relay Merge Capabilities Specifies the merge capabilities of a Frame Relay switch. The following values are supported in this version of the specification: Value Meaning 0 Merge not supported 1 Merge supported Non-merge and merge Frame Relay LSRs may freely interoperate.' Please refer to the following reference for a complete description of this feature. Enumeration: 'supported': 1, 'notSupported': 0.
                     mplsLdpEntityFrameRelayLRComponents 1.3.6.1.2.1.10.166.6.1.1.1.1.3 unsigned32 read-only
Number of Label Range Components in the Initialization message. This also represents the number of entries in the mplsLdpEntityFrameRelayLRTable which correspond to this entry. This is the EXACT value for the Frame Relay Session Parameter, field N (for Number of label range components). The Frame Relay Session Parameter is an optional parameter in the Initialization Message. The description from rfc3036.txt is: 'N, Number of label range components Specifies the number of Frame Relay Label Range Components included in the TLV.' Please refer to the following reference for a complete description of this feature.
                     mplsLdpEntityFrameRelayVcDirectionality 1.3.6.1.2.1.10.166.6.1.1.1.1.4 integer read-only
If the value of this object is 'bidirectional(0)', then the LSR supports the use of a given DLCI as a label for both directions independently. If the value of this object is 'unidirectional(1)', then the LSR uses the given DLCI as a label in only one direction. This is the EXACT value for the Frame Relay Session Parameter, field D (for VC Directionality). The Frame Relay Session Parameter is an optional parameter in the Initialization Message. The description from rfc3036.txt is: 'D, VC Directionality A value of 0 specifies bidirectional VC capability, meaning the LSR can support the use of a given DLCI as a label for both link directions independently. A value of 1 specifies unidirectional VC capability, meaning a given DLCI may appear in a label mapping for one direction on the link only. When either or both of the peers specifies unidirectional VC capability, both LSRs use unidirectional VC label assignment for the link as follows. The LSRs compare their LDP Identifiers as unsigned integers. The LSR with the larger LDP Identifier may assign only odd-numbered DLCIs in the range as labels. The system with the smaller LDP Identifier may assign only even-numbered DLCIs in the range as labels.' Please refer to the following reference for a complete description of this feature. Enumeration: 'bidirectional': 0, 'unidirection': 1.
                     mplsLdpEntityFrameRelayStorageType 1.3.6.1.2.1.10.166.6.1.1.1.1.5 storagetype read-only
The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row.
                     mplsLdpEntityFrameRelayRowStatus 1.3.6.1.2.1.10.166.6.1.1.1.1.6 rowstatus read-only
The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated.
             mplsLdpEntityFrameRelayLRTable 1.3.6.1.2.1.10.166.6.1.1.2 no-access
This table contains information about the Optional Parameters for the Frame Relay Session in the LDP Initialization Message, specifically it contains information about the Frame Relay Label Range Components. If the value of the object 'mplsLdpEntityOptionalParameters' contains the value of 'frameRelaySessionParameters(3)' then there must be at least one corresponding entry in this table.
                 mplsLdpEntityFrameRelayLREntry 1.3.6.1.2.1.10.166.6.1.1.2.1 no-access
An entry in this table represents the Frame Relay Label Range Component associated with the LDP entity.
                     mplsLdpEntityFrameRelayLRMinDlci 1.3.6.1.2.1.10.166.6.1.1.2.1.1 dlci no-access
The lower bound which is supported. This value should be the same as that in the Frame Relay Label Range Component's Minimum DLCI field. The value of zero is valid for the minimum DLCI field of the label.
                     mplsLdpEntityFrameRelayLRMaxDlci 1.3.6.1.2.1.10.166.6.1.1.2.1.2 dlci read-only
The upper bound which is supported. This value should be the same as that in the Frame Relay Label Range Component's Maximum DLCI field.
                     mplsLdpEntityFrameRelayLRLen 1.3.6.1.2.1.10.166.6.1.1.2.1.3 integer read-only
This object specifies the length of the DLCI bits. This is the EXACT value for the Len field of the Frame Relay Label Range Component. The description from rfc3036.txt is: 'Len This field specifies the number of bits of the DLCI. The following values are supported: Len DLCI bits 0 10 2 23 Len values 1 and 3 are reserved.' Please refer to the following reference for a complete description of this feature. Enumeration: 'tenDlciBits': 0, 'twentyThreeDlciBits': 2.
                     mplsLdpEntityFrameRelayLRStorageType 1.3.6.1.2.1.10.166.6.1.1.2.1.4 storagetype read-only
The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row.
                     mplsLdpEntityFrameRelayLRRowStatus 1.3.6.1.2.1.10.166.6.1.1.2.1.5 rowstatus read-only
The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated.
         mplsLdpFrameRelaySessionObjects 1.3.6.1.2.1.10.166.6.1.2
             mplsLdpFrameRelaySessionTable 1.3.6.1.2.1.10.166.6.1.2.1 no-access
A table of Frame Relay label range intersections between the LDP Entities and LDP Peers. Each row represents a single label range intersection. NOTE: this table cannot use the 'AUGMENTS' clause because there is not necessarily a one-to-one mapping between this table and the mplsLdpSessionTable.
                 mplsLdpFrameRelaySessionEntry 1.3.6.1.2.1.10.166.6.1.2.1.1 no-access
An entry in this table represents information on a single label range intersection between an LDP Entity and LDP Peer. The information contained in a row is read-only.
                     mplsLdpFrameRelaySessionMinDlci 1.3.6.1.2.1.10.166.6.1.2.1.1.1 dlci no-access
The lower bound of DLCIs which are supported. The value of zero is a valid value for the minimum DLCI field of the label.
                     mplsLdpFrameRelaySessionMaxDlci 1.3.6.1.2.1.10.166.6.1.2.1.1.2 dlci read-only
The upper bound of DLCIs which are supported.
                     mplsLdpFrameRelaySessionLen 1.3.6.1.2.1.10.166.6.1.2.1.1.3 integer read-only
This object specifies the DLCI bits. Enumeration: 'tenDlciBits': 0, 'twentyThreeDlciBits': 2.
     mplsLdpFrameRelayConformance 1.3.6.1.2.1.10.166.6.2
         mplsLdpFrameRelayGroups 1.3.6.1.2.1.10.166.6.2.1
             mplsLdpFrameRelayGroup 1.3.6.1.2.1.10.166.6.2.1.1
Objects that apply to all MPLS LDP implementations using Frame Relay as the Layer 2.
         mplsLdpFrameRelayCompliances 1.3.6.1.2.1.10.166.6.2.2
             mplsLdpFrameRelayModuleFullCompliance 1.3.6.1.2.1.10.166.6.2.2.1
The Module is implemented with support for read-create and read-write. In other words, both monitoring and configuration are available when using this MODULE-COMPLIANCE.
             mplsLdpFrameRelayModuleReadOnlyCompliance 1.3.6.1.2.1.10.166.6.2.2.2
The Module is implemented with support for read-only. In other words, only monitoring is available by implementing this MODULE-COMPLIANCE.