MPLS-FRR-GENERAL-STD-MIB: View SNMP OID List / Download MIB

VENDOR: INTERNET-STANDARD


 Home MIB: MPLS-FRR-GENERAL-STD-MIB
Download as:   

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 mplsFrrGeneralMIB 1.3.6.1.2.1.202
Copyright (c) 2011 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). This MIB module contains generic object definitions for MPLS Traffic Engineering Fast Reroute as defined in RFC 4090.
         mplsFrrGeneralObjects 1.3.6.1.2.1.202.1
             mplsFrrGeneralProtectionMethod 1.3.6.1.2.1.202.1.1 integer read-write
Indicates which protection method is to be used for fast reroute on this device. Some devices may require a reboot if this variable is to take effect after being modified. Enumeration: 'unknown': 1, 'facilityBackup': 3, 'oneToOneBackup': 2.
             mplsFrrGeneralIngressTunnelInstances 1.3.6.1.2.1.202.1.2 counter32 read-only
The number of tunnel instances for either detour LSPs or bypass tunnels for which this LSR is the ingress.
             mplsFrrGeneralConstraintsTable 1.3.6.1.2.1.202.1.3 no-access
This table shows detour LSP or bypass tunnel setup constraints.
                 mplsFrrGeneralConstraintsEntry 1.3.6.1.2.1.202.1.3.1 no-access
An entry in this table represents detour LSP or bypass tunnel setup constraints for an interface or link to be protected by detour LSPs or a bypass tunnel. Once the LSP or tunnel instance to be protected is identified in the mplsTunnelTable, the corresponding mplsTunnelIfIndex value of that tunnel can be used to get the ifIndex of the underlying physical interface using the ifStackTable. That ifIndex of the underlying physical interface will be used as mplsFrrGeneralConstraintsIfIndexOrZero in this table to protect the LSPs or tunnel instances determined earlier. It is recommended that ifIndex persistence be enabled across re-initializations. If persistence is not implemented, then the value of mplsFrrGeneralConstraintsIfIndexOrZero in this table cannot be guaranteed across restarts and all entries in this table MUST NOT be persistent, or the values of mplsFrrGeneralConstraintsIfIndexOrZero MUST be reconstructed on restart. SNMP engines must only allow entries in this table to be created for tunnel instances that require fast reroute as indicated by the presence of the FAST_REROUTE object in the signaling for the LSP in question. An entry in this table can be created only if a corresponding entry in mplsTunnelTable exists with the same mplsTunnelIndex as mplsFrrGeneralConstraintsTunnelIndex. Entries in this table are deleted when the corresponding entries in mplsTunnelTable are deleted. It is recommended that entries in this table be persistent across reboots. Entries indexed with mplsFrrGeneralConstraintsIfIndexOrZero and set to 0 apply to all interfaces on this device for which the FRR feature can operate. If the mplsTunnelInstance object is set to a value of 0, it indicates that the mplsTunnelEntry contains a tunnel ingress. This is typically how configuration of this feature is performed on devices where the actual protection LSP used is left up to the protecting tunnel. However, in cases where static configuration is possible, any valid tunnel instance is possible; however, it is strongly RECOMMENDED that the instance index SHOULD use the following convention to identify backup LSPs: - lower 16 bits : protected tunnel instance - higher 16 bits: must be all zeros
                     mplsFrrGeneralConstraintsIfIndexOrZero 1.3.6.1.2.1.202.1.3.1.1 interfaceindexorzero no-access
Uniquely identifies an interface that a fast-reroute protection tunnel is configured to potentially protect in the event of a fault. Entries with this index set to 0 indicate that the configured protection tunnel protects all interfaces on this device (i.e., node protection).
                     mplsFrrGeneralConstraintsTunnelIndex 1.3.6.1.2.1.202.1.3.1.2 mplstunnelindex no-access
Uniquely identifies a tunnel in the mplsTunnelTable that is configured to possibly protect the interface(s) specified by mplsFrrGeneralConstraintsIfIndexOrZero in the event of a fault.
                     mplsFrrGeneralConstraintsTunnelInstance 1.3.6.1.2.1.202.1.3.1.3 mplstunnelinstanceindex no-access
Uniquely identifies an existing instance of this tunnel for which fast reroute is requested. Note that a value of 0 indicates that the configuration points at a tunnel head (as specified in RFC 3812). This is typically how configuration of this feature is performed on devices where the actual protection LSP used is left up to the protecting tunnel. However, in cases where static configuration is possible, any valid tunnel instance is permissible. In these cases, it is recommended that the instance index follow the following convention so as to make identification of backup LSPs easier: - lower 16 bits : protected tunnel instance - higher 16 bits: must be all zeros
                     mplsFrrGeneralConstraintsProtectionType 1.3.6.1.2.1.202.1.3.1.4 integer read-only
Indicates type of the resource protection: linkProtection(1) indicates that this tunnel is set up to protect a particular link's resources. nodeProtection(2) indicates that this tunnel is set up to protect an entire node from failure. Enumeration: 'nodeProtection': 2, 'linkProtection': 1.
                     mplsFrrGeneralConstraintsSetupPrio 1.3.6.1.2.1.202.1.3.1.5 unsigned32 read-only
Indicates the setup priority of the detour LSP or bypass tunnel.
                     mplsFrrGeneralConstraintsHoldingPrio 1.3.6.1.2.1.202.1.3.1.6 unsigned32 read-only
Indicates the holding priority for the detour LSP or bypass tunnel.
                     mplsFrrGeneralConstraintsInclAnyAffinity 1.3.6.1.2.1.202.1.3.1.7 mplstunnelaffinity read-only
Indicates the include-any link constraint for the detour LSP or bypass tunnel. A link satisfies the include-any constraint if and only if the constraint is zero, or the link and the constraint have a resource class in common.
                     mplsFrrGeneralConstraintsInclAllAffinity 1.3.6.1.2.1.202.1.3.1.8 mplstunnelaffinity read-only
Indicates the include-all link constraint for the detour LSP or bypass tunnel. A link satisfies the include-all constraint if and only if the link contains all of the administrative groups specified in the constraint.
                     mplsFrrGeneralConstraintsExclAnyAffinity 1.3.6.1.2.1.202.1.3.1.9 mplstunnelaffinity read-only
Indicates the exclude-any link constraint for the detour LSP or bypass tunnel. A link satisfies the exclude-any constraint if and only if the link contains none of the administrative groups specified in the constraint.
                     mplsFrrGeneralConstraintsHopLimit 1.3.6.1.2.1.202.1.3.1.10 unsigned32 read-only
The maximum number of hops that the detour LSP or bypass tunnel may traverse.
                     mplsFrrGeneralConstraintsBandwidth 1.3.6.1.2.1.202.1.3.1.11 mplsbitrate read-only
The maximum bandwidth specifically reserved for a detour LSP or bypass tunnel, in units of thousands of bits per second (kbps). Note that setting this value to 0 indicates best-effort treatment.
                     mplsFrrGeneralConstraintsStorageType 1.3.6.1.2.1.202.1.3.1.12 storagetype read-only
The storage type for this configuration entry. Conceptual rows having the value 'permanent' need not allow write access to any columnar objects in the row.
                     mplsFrrGeneralConstraintsRowStatus 1.3.6.1.2.1.202.1.3.1.13 rowstatus read-only
This object is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modified except mplsFrrGeneralConstraintsRowStatus and mplsFrrGeneralConstraintsStorageType.
             mplsFrrGeneralTunnelARHopTable 1.3.6.1.2.1.202.1.4 no-access
This table sparsely extends mplsTunnelARHopTable defined in the MPLS-TE-STD-MIB module with fast-reroute objects. These objects specify the status of local protection, including availability and active use, on a per-hop basis, of hops traversed by a protected tunnel.
                 mplsFrrGeneralTunnelARHopEntry 1.3.6.1.2.1.202.1.4.1 no-access
This entry contains fast-reroute protection status of a single protected tunnel hop.
                     mplsFrrGeneralTunnelARHopSessionAttributeFlags 1.3.6.1.2.1.202.1.4.1.1 bits read-only
This object indicates the desired values for the associated SESSION_ATTRIBUTE flags. Note that since this object is a BITS type, the bits may be set to indicate various desired combinations of the SESSION_ATTRIBUTE flags. If SESSION_ATTRIBUTE flags are not supported, then this object contains the value of arHopSessionAttrFlagsUnsupported(0). Bits: 'bandwidthProtectionDesired': 4, 'nodeProtectionDesired': 5, 'sestyleDesired': 3, 'localProtectionDesired': 1, 'labelRecordingDesired': 2, 'arHopSessionAttrFlagsUnsupported': 0.
                     mplsFrrGeneralTunnelARHopRROSubObjectFlags 1.3.6.1.2.1.202.1.4.1.2 bits read-only
This object indicates the flags that are currently in use by the associated Record Route Object (RRO) sub-object. Note that since this object is a BITS type, the bits may be set to indicate various combinations of the flags. If the RRO sub-object is not supported, then this object contains the value of arHopRROSubObjectFlagsUnsupported(0). Bits: 'bandwidthProtection': 3, 'localProtectionInUse': 2, 'nodeProtection': 4, 'localProtectionAvailable': 1, 'arHopRROSubObjectFlagsUnsupported': 0.
         mplsFrrGeneralConformance 1.3.6.1.2.1.202.2
             mplsFrrGeneralCompliances 1.3.6.1.2.1.202.2.1
                 mplsFrrGeneralModuleFullCompliance 1.3.6.1.2.1.202.2.1.1
Compliance statements for SNMP engines that support the MPLS-FRR-GENERAL-STD-MIB module.
                 mplsFrrGeneralModuleReadOnlyCompliance 1.3.6.1.2.1.202.2.1.2
Compliance statements for SNMP engines that support the MPLS-FRR-GENERAL-STD-MIB module.
             mplsFrrGeneralGroups 1.3.6.1.2.1.202.2.2
                 mplsFrrGeneralScalarGroup 1.3.6.1.2.1.202.2.2.1
Objects that are required to display general fast-reroute information.
                 mplsFrrGeneralConstraintsGroup 1.3.6.1.2.1.202.2.2.2
Objects that are required to configure fast-reroute constraints at the ingress LSR of the tunnel that requires fast-reroute service.
                 mplsFrrGeneralTunnelARHopGroup 1.3.6.1.2.1.202.2.2.3
Objects that are required to present per-hop fast-reroute protection status.