MICOM-4400-VOICE-NETWORK-MIB: View SNMP OID List / Download MIB

NAME = ; DESC = The VNET Voice Channel Configuration table. \ (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Channel Configuration \ table. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The card lim (logical interface module) number of a \ particular voice channel. Used as an index to the \ VNET Voice Channel Configuration table. (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'lim2': 3, 'lim3': 4, 'lim1': 2, 'lim4': 5, 'limB': 6, 'limC': 7, 'limD': 8, 'limE': 9.

NAME = ; DESC = The position of the voice channel in the lim. \ Used as an index to the VNET Voice \ Channel Configuration table. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the profile \ to be used to configure the specified voice \ channel. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the profile \ to be used for a switching call. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the interface \ type of the specified voice channel. (Operational); HELP = Upon powerup, the interface type will not be \ available until the DSP software is loaded and its \ status is reported.; CAPABILITIES = ; Enumeration: 'not-available': 1, 'low-cost-loop-start-FXS': 5, 'three-port': 10, 'dvm': 11, 'ground-start-FXO': 9, 'enhanced-EandM': 3, 'enhanced-loop-start-FXO': 4, 'ground-start-FXS': 8, 'bri': 12, 'enhanced-loop-start-FXS': 2, 'low-cost-EandM': 6, 'low-cost-loop-start-FXO': 7.

NAME = ; DESC = The VNET Voice Profile Configuration table. \ (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Profile Configuration \ table. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the profile \ number. Used as an index to the VNET Voice \ Profile Configuration table. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects the voice \ channel signal processing. (Operational); HELP = Can be used to set to either dual mode with \ both voice and fax, or just voice.; CAPABILITIES = ; Enumeration: 'voiceOnly': 2, 'voiceFax': 1.

NAME = ; DESC = The value of this object selects the voice \ digitizing algorithm. (Operational); HELP = Rate at which voice is digitized in \ designated in bits per second.; CAPABILITIES = ; Enumeration: 'rateG729-8K-40MS': 2, 'rateG729': 1.

NAME = ; DESC = The value of this object selects the input \ signal gain in dB. (Operational); HELP = For DVM, max value is 8 dB. If more than \ 8 dB is configured, 8 dB will be used. \ The range for the BRI card is -15 to 15 dB.; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects the output \ signal attenuation in dB. (Operational); HELP = For DVM, max value is 8 dB. If more than \ 8 dB is configured, 8 dB will be used. \ The range for the BRI card is -15 to 15dB.; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects the voice \ channel busy out control type. (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'forceOff': 3, 'systemControlled': 1, 'forceOn': 2.

NAME = ; DESC = The value of this object selects the voice \ channel link bandwidth reservation style. \ (Operational); HELP = 2 is used for forced connects or PVCs only. \ 1 is used for switched connects.; CAPABILITIES = ; Enumeration: 'voiceActivated': 1, 'continuous': 2.

NAME = ; DESC = The value of this object selects the voice \ channel background noise generation type. \ (Operational); HELP = The ability of passing background noise or \ silencing the channel during idle periods. \ First option allows the background noise to be \ regenerated during the periods, whereas the \ second option suppresses background noise during \ idle periods.; CAPABILITIES = ; Enumeration: 'regenerated': 1, 'silence': 2.

NAME = ; DESC = The value of this object selects the voice \ channel pulse rate in pulses per second. \ (Operational); HELP = NOTE: This object is used by the Partner card \ and not for the ISDN BRI voice card.; CAPABILITIES = ; Enumeration: 'pulses20PerSec': 2, 'pulses10PerSec': 1, 'pulses125PerSec': 3.

NAME = ; DESC = The value of this object specifies the voice \ channel E&M signaling format. (Operational); HELP = 2 and 3 are used for force connects only. \ 1 (DC) is used for switched connects.; CAPABILITIES = ; Enumeration: 'pulsedDC': 3, 'tone2280': 2, 'dc': 1, 'winkStart': 4.

NAME = ; DESC = The value of this object specifies the voice \ channel FXS signaling format. (Operational); HELP = 1 is used for force connects only. \ 2 is used for switched connects.; CAPABILITIES = ; Enumeration: 'repeatedRing': 1, 'interruptedRing': 2.

NAME = ; DESC = The value of this object specifies the voice \ channel DVM signaling format. (Operational); HELP = 3 and 4 are used for force connects only. \ 1 is used for switched connects.; CAPABILITIES = ; Enumeration: 'tone2280': 3, 'spainCAS': 11, 'r2Q421': 8, 'clearChannel': 4, 'winkStart': 12, 'r2PUNCOM': 7, 'dC5B': 5, 'dC5BInvert': 6, 'dC5RonTron': 9, 'tieTrunk': 1, 'tieInvert': 2, 'israelCAS': 10.

NAME = ; DESC = The value of this object specifies when the \ voice channel (FXO or 3-port) will answer \ the call request. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the E&M \ voice channel operation as either 2 or 4 wire \ operation. (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'twoWire': 1, 'fourWire': 2.

NAME = ; DESC = The value of this object specifies the voice \ channel (FXS or 3-port) ringing frequency. \ (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'freq50Hz': 2, 'freq25Hz': 1.

NAME = ; DESC = The value of this object selects the voice \ channel Fax digitizing rate in bits per second. \ (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'voiceRate': 1, 'rate4800': 3, 'rate2400': 2, 'rate7200': 4, 'rate9600': 5.

NAME = ; DESC = The value of this object selects the voice \ channel method to detect the line disconnect. \ (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'powerInterrupt': 2, 'tone': 1.

NAME = ; DESC = The value of this object selects the voice \ channel type of line impedance. (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'impedance600Ohms': 1, 'complex': 2.

NAME = ; DESC = The value of this object specifies the voice \ channel maximum output level. (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'zerodBMNominal': 1, 'plus7dBM': 2.

NAME = ; DESC = The value of this object specifies the voice \ channel time (in seconds) to delay before dialing \ out the number (i.e., time to wait for dial tone). \ (Operational); HELP = NOTE: This object is not required for the ISDN BRI \ voice card; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the voice \ channel inter-digit time-out time (in seconds). \ (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the voice \ channel maximum number of digits that can \ be dialed. (Operational); HELP = 0 is used for auto-call functionality.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the voice \ channel dial digit regeneration format. \ (Operational); HELP = NOTE: This object is not required for the ISDN \ BRI voice card.; CAPABILITIES = ; Enumeration: 'dialPulse': 1, 'dtmf': 2.

NAME = ; DESC = The value of this object specifies the voice \ channel call progress tone required for different \ countries or areas. (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'europe': 4, 'northAmerica': 1, 'unitedKingdom': 3, 'france': 5, 'australia': 8, 'centralAmerica': 6, 'chile': 7, 'japan': 2.

NAME = ; DESC = The value of this object specifies to the voice \ channel whether to turn on or off the DTMF \ detector. (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'enable': 2, 'disable': 1.

NAME = ; DESC = The value of this object specifies the voice \ channel maximum jitters delay (in milliseconds). \ (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies to the voice \ channel whether to turn on or off the echo \ canceller. (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'enable': 2, 'disable': 1.

NAME = ; DESC = The value of this object specifies to the voice \ channel whether to automatically set the input \ signal level. (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'enable': 2, 'disable': 1.

NAME = ; DESC = The value of this object specifies the voice \ channel (DVM or BRI) compander type. \ (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'uLaw': 1, 'aLaw': 2.

NAME = ; DESC = The value of this object specifies to the voice \ channel (DVM) whether to enable or disable the \ transparent voice (no compression) algorithm. \ (Operational); HELP = This object is also used by the ISDN BRI voice card \ to enable/disable Digital Lossless Switching Pattern \ Generation and Pattern Search.; CAPABILITIES = ; Enumeration: 'disable-compress': 1, 'enable-notcompress': 2.

NAME = ; DESC = The value of this object specifies to the voice \ channel whether '#' is used to end a dialing input. \ (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'enable': 2, 'disable': 1.

NAME = ; DESC = Signal input above this level is considered\ a voiced signal, below this level, the \ Voice Activity Detector (VAD), will \ determine if it is a voiced signal or \ background noise. (Operational); HELP = Refer to the International \ Telecommunication Union(ITU-T) G.711 \ document for more information; CAPABILITIES = ; Enumeration: 'neg25dbm0': 1, 'neg35dbm0': 3, 'neg30dbm0': 2, 'neg40dbm0': 4, 'neg45dbm0': 5.

NAME = ; DESC = Indicates the time delay to switch \ from voice to silence.\ (Operational); HELP = ; CAPABILITIES = ; Enumeration: 'msec700': 7, 'msec300': 3, 'msec800': 8, 'msec400': 4, 'msec500': 5, 'msec100': 1, 'msec600': 6, 'msec200': 2.

NAME = ; DESC = The value of this object represents the \ Idle pattern on the line when no call is up.\ Specific to a PBX. This is a permanent DSP \ configuration parameter; HELP = This value can be used to detect that a call \ has finished and that the echo canceller should \ be reset and that fax mode should be terminated.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the filter \ length for echo canceller. This is a permanent \ DSP configuration parameter.; HELP = A length of 128 is equal to 16ms.\ A length of 256 is equal to 32ms.; -- NOTE: The ISDN BRI voice card supports 32ms only; CAPABILITIES = ; Enumeration: 'length256': 2, 'length128': 1.

NAME = ; DESC = The value of this object is used for echo \ canceller Er1 improvement. This is a DSP \ Dynamic configuration parameter. \ A signal will be attenuated by this dB \ amount before being passed through the \ echo canceller. After the echo canceller, \ it will be amplified by this same dB amount, \ for a net gain of 0 dB. \ This attenuation amplicfication cycle reduces \ the resolution of the signal ( -18 ..0 ).; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object will suppress the \ impulsive backround noise in order to achieve \ silence suppression savings. HELP = ; CAPABILITIES = ;

NAME = ; DESC = DTMF burst generation in milliseconds.; HELP = ; CAPABILITIES = ; Enumeration: 'time70msec': 3, 'time100msec': 4, 'time50msec': 1, 'time60msec': 2.

NAME = ; DESC = DTMF burst Regeneration length in milliseconds.; HELP = ; CAPABILITIES = ; Enumeration: 'time70msec': 3, 'time100msec': 4, 'time50msec': 1, 'time60msec': 2.

NAME = ; DESC = The VNET Voice Switching Profile Configuration \ table.(Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Switching Profile \ Configuration table. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the profile \ number. Used as an index to the VNET Voice \ Switching Profile Configuration table. \ (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies how to \ handle outgoing calls for voice channel \ switching. (Operational); HELP = 2: include CUG ID in outgoing call. \ 3: include restriction class in outgoing call. \ 4: include both CUG ID and restriction \ class in outgoing call. \ 5: outgoing call is not allowed.; CAPABILITIES = ; Enumeration: 'closedUserGroupCall': 2, 'restrictionClassCall': 3, 'noRestriction': 1, 'bothCUGandRCCall': 4, 'inhibitAll': 5.

NAME = ; DESC = The value of this object specifies how to \ handle incoming calls for voice channel \ switching. (Operational); HELP = 2: check CUG ID in incoming call. (Must \ match our CUG ID for call acceptance. \ 3: check RCC in incoming call. (Must be \ greater than or equal to our RCC for call \ acceptance. \ 4: check both CUG and RCC in incoming \ call. \ 5: incoming call is not allowed.; CAPABILITIES = ; Enumeration: 'checkRestrictionClassCode': 3, 'cUGandPublicClassInhibit': 4, 'noRestriction': 1, 'checkCUGID': 2, 'inhibitAll': 5.

NAME = ; DESC = The value of this object assigns the Closed \ User Group ID for a voice channel. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object assigns the Restriction \ Class Code for a voice channel. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object provides a voice \ channel Auto Call destination number by \ specifying an index into the ingress table. \ (Operational); HELP = 0: auto call disabled. \ 1-32: index to the ingress table entry where \ the dial number is specified. \ The auto call for the ISDN BRI voice card is \ always disabled.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the preference \ for the voice algorithm when an outgoing call is \ made. (Operational); HELP = specific: whatever is configured. \ bandwidth: bigger block size. \ delay: shorter block size.; CAPABILITIES = ; Enumeration: 'specific': 1, 'delay': 3, 'bandwidth': 2.

NAME = ; DESC = The value of this object assigns the priority \ of the voice data to be transmitted. (Operational); HELP = 0: lowest priority. \ 15: highest priority.; CAPABILITIES = ;

NAME = ; DESC = Indicates the type of auto-call \ switching to be performed by the \ voice channel.; HELP = ; CAPABILITIES = ; Enumeration: 'masterHootnHoller': 2, 'slaveHootnHoller': 3, 'normal': 1.

NAME = ; DESC = Indicates which DNA server is used.; HELP = ; CAPABILITIES = ; Enumeration: 'nas': 1, 'vncs': 2.

NAME = ; DESC = Indicates the type of call being made.; HELP = ; CAPABILITIES = ; Enumeration: 'enblock-only': 1, 'dynamic': 2.

NAME = ; DESC = The VNET Voice Ingress Digit Filtering \ Configuration table. (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Ingress Digit \ Filtering Configuration table. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the index to \ the ingress table. Used as an index to the VNET \ Voice Ingress Digit Filtering Configuration table. \ Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects the digit \ pattern to be matched. (Null terminated \ character string.) (Operational); HELP = Valid characters are decimal digits, '#', \ '*', '+', '[' and ']' .; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects commands \ to produce the ingress digits for speed dial, \ call redirect, and source ID insertion features. \ (Operational); HELP = Valid characters are decimal digits, '#', \ '*', 'D', and 'I'.; CAPABILITIES = ;

NAME = ; DESC = The VNET Voice Egress Digit Manipulation \ Configuration table. (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Egress Digit \ Manipulation Configuration table. (Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the index to \ the egress table. Used as an index to the VNET \ Voice Egress Digit Manipulation Configuration \ table. Operational); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects the phone \ number that voice channels are associated with. \ This is the number to be registered to the Address \ Server (RSA). (Operational); HELP = Valid characters are decimal digits, '#', and '*'.; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects commands \ to produce the egress digits for FXO, E&M, \ or FXS 3-Port interface. The result is the \ number to be sent to the connected phone \ device. (Operational); HELP = Valid characters are decimal digits, '#', '*', \ '+', 'D', 'H', and 'I'. The character 'H' is used \ used to trigger immediate dial handling by the PBX.; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects voice channels \ associated with the phone number. The valid \ string consists of the substring 'B1'~'B6', \ 'C1'~'C12', 'D1'~'D12', and 'E1'~'E2'. \ (Operational); HELP = Valid characters are decimal digits, 'B', 'C', \ 'D', and 'E'.; CAPABILITIES = ;

NAME = ; DESC = The VNET Voice Channel Configuration table. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Channel Configuration \ table. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The card lim (logical interface module) number of a \ particular voice channel. Used as an index to the \ VNET Voice Channel Configuration table. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'lim2': 3, 'lim3': 4, 'lim1': 2, 'lim4': 5, 'limB': 6, 'limC': 7, 'limD': 8, 'limE': 9.

NAME = ; DESC = The position of the voice channel in the lim. \ Used as an index to the VNET Voice \ Channel Configuration table. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the profile \ to be used to configure the specified voice \ channel. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the profile \ to be used for a switching call. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the interface \ type of the specified voice channel. (Configuration); HELP = Upon powerup, the interface type will not be \ available until the DSP software is loaded and its \ status is reported.; CAPABILITIES = ; Enumeration: 'not-available': 1, 'low-cost-loop-start-FXS': 5, 'three-port': 10, 'dvm': 11, 'ground-start-FXO': 9, 'enhanced-EandM': 3, 'enhanced-loop-start-FXO': 4, 'ground-start-FXS': 8, 'bri': 12, 'enhanced-loop-start-FXS': 2, 'low-cost-EandM': 6, 'low-cost-loop-start-FXO': 7.

NAME = ; DESC = The VNET Voice Profile Configuration table. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Profile Configuration \ table. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the profile \ number. Used as an index to the VNET Voice \ Profile Configuration table. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects the voice \ channel signal processing. (Configuration); HELP = Can be used to set to either dual mode with \ both voice and fax, or just voice.; CAPABILITIES = ; Enumeration: 'voiceOnly': 2, 'voiceFax': 1.

NAME = ; DESC = The value of this object selects the voice \ digitizing algorithm. (Configuration); HELP = Rate at which voice is digitized in \ designated in bits per second.; CAPABILITIES = ; Enumeration: 'rateG729-8k-40ms': 2, 'rateG729': 1.

NAME = ; DESC = The value of this object selects the input \ signal gain in dB. (Configuration); HELP = For DVM, max value is 8 dB. If more than \ 8 dB is configured, 8 dB will be used.\ The ISDN BRI voice card range is -15 to 15dB.; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects the output \ signal attenuation in dB. (Configuration); HELP = For DVM, max value is 8 dB. If more than \ 8 dB is configured, 8 dB will be used.; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects the voice \ channel busy out control type. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'forceOff': 3, 'systemControlled': 1, 'forceOn': 2.

NAME = ; DESC = The value of this object selects the voice \ channel link bandwidth reservation style. \ (Configuration); HELP = 2 is used for forced connects or PVCs only. \ 1 is used for switched connects.; CAPABILITIES = ; Enumeration: 'voiceActivated': 1, 'continuous': 2.

NAME = ; DESC = The value of this object selects the voice \ channel background noise generation type. \ (Configuration); HELP = The ability of passing background noise or \ silencing the channel during idle periods. \ First option allows the background noise to be \ regenerated during the periods, whereas the \ second option suppresses background noise during \ idle periods.; CAPABILITIES = ; Enumeration: 'regenerated': 1, 'silence': 2.

NAME = ; DESC = The value of this object selects the voice \ channel pulse rate in pulses per second. \ (Configuration); HELP = NOTE: This object is used by the Partner Card, \ not by the ISDN BRI voice card.; CAPABILITIES = ; Enumeration: 'pulses20PerSec': 2, 'pulses10PerSec': 1, 'pulses125PerSec': 3.

NAME = ; DESC = The value of this object specifies the voice \ channel E&M signaling format. (Configuration); HELP = 2 and 3 are used for force connects only. \ 1 (DC) is used for switched connects.; CAPABILITIES = ; Enumeration: 'pulsedDC': 3, 'tone2280': 2, 'dc': 1, 'winkStart': 4.

NAME = ; DESC = The value of this object specifies the voice \ channel FXS signaling format. (Configuration); HELP = 1 is used for force connects only. \ 2 is used for switched connects.; CAPABILITIES = ; Enumeration: 'repeatedRing': 1, 'interruptedRing': 2.

NAME = ; DESC = The value of this object specifies the voice \ channel DVM signaling format. (Configuration); HELP = 3 and 4 are used for force connects only. \ 1 is used for switched connects.; CAPABILITIES = ; Enumeration: 'tone2280': 3, 'spainCAS': 11, 'r2Q421': 8, 'clearChannel': 4, 'winkStart': 12, 'r2PUNCOM': 7, 'dC5B': 5, 'dC5BInvert': 6, 'dC5RonTron': 9, 'tieTrunk': 1, 'tieInvert': 2, 'israelCAS': 10.

NAME = ; DESC = The value of this object specifies when the \ voice channel (FXO or 3-port) will answer \ the call request. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the E&M \ voice channel operation as either 2 or 4 wire \ operation. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'twoWire': 1, 'fourWire': 2.

NAME = ; DESC = The value of this object specifies the voice \ channel (FXS or 3-port) ringing frequency. \ (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'freq50Hz': 2, 'freq25Hz': 1.

NAME = ; DESC = The value of this object selects the voice \ channel Fax digitizing rate in bits per second. \ (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'voiceRate': 1, 'rate4800': 3, 'rate2400': 2, 'rate7200': 4, 'rate9600': 5.

NAME = ; DESC = The value of this object selects the voice \ channel method to detect the line disconnect. \ (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'powerInterrupt': 2, 'tone': 1.

NAME = ; DESC = The value of this object selects the voice \ channel type of line impedance. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'impedance600Ohms': 1, 'complex': 2.

NAME = ; DESC = The value of this object specifies the voice \ channel maximum output level. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'zerodBMNominal': 1, 'plus7dBM': 2.

NAME = ; DESC = The value of this object specifies the voice \ channel time (in seconds) to delay before dialing \ out the number (i.e., time to wait for dial tone). \ (Configuration); HELP = NOTE : This object is not used for the ISDN BRI \ voice card.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the voice \ channel inter-digit time-out time (in seconds). \ (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the voice \ channel maximum number of digits that can \ be dialed. (Configuration); HELP = 0 is used for auto-call functionality.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the voice \ channel dial digit regeneration format. \ (Configuration); HELP = NOTE: THIS object is not used for the ISDN \ BRI voice card.; CAPABILITIES = ; Enumeration: 'dialPulse': 1, 'dtmf': 2.

NAME = ; DESC = The value of this object specifies the voice \ channel call progress tone required for different \ countries or areas. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'northAmerica': 1, 'unitedKingdom': 3, 'france': 5, 'australia': 8, 'centralAmerica': 6, 'chile': 7, 'japan': 2, 'europe-germany': 4.

NAME = ; DESC = The value of this object specifies to the voice \ channel whether to turn on or off the DTMF \ detector. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'enable': 2, 'disable': 1.

NAME = ; DESC = The value of this object specifies the voice \ channel maximum jitters delay (in milliseconds). \ (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies to the voice \ channel whether to turn on or off the echo \ canceller. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'enable': 2, 'disable': 1.

NAME = ; DESC = The value of this object specifies to the voice \ channel whether to automatically set the input \ signal level. (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'enable': 2, 'disable': 1.

NAME = ; DESC = The value of this object specifies the voice \ channel (DVM or BRI) compander type. \ (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'uLaw': 1, 'aLaw': 2.

NAME = ; DESC = The value of this object specifies to the voice \ channel (DVM) whether to enable or disable the \ transparent voice (no compression) algorithm. \ (Configuration); HELP = This object is also used by the ISDN BRI voice \ card to enable/disable Digital Lossless Switching \ Pattern Generation and Pattern Search.; CAPABILITIES = ; Enumeration: 'disable-compress': 1, 'enable-notcompress': 2.

NAME = ; DESC = The value of this object specifies to the voice \ channel whether '#' is used to end a dialing input. \ (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'enable': 2, 'disable': 1.

NAME = ; DESC = Signal input above this level is considered\ a voiced signal, below this level, the \ Voice Activity Detector (VAD), will \ determine if it is a voiced signal or \ background noise. (Configuration); HELP = Refer to the International \ Telecommunication Union(ITU-T) G.711 \ document for more information; CAPABILITIES = ; Enumeration: 'neg25dbm0': 1, 'neg35dbm0': 3, 'neg30dbm0': 2, 'neg40dbm0': 4, 'neg45dbm0': 5.

NAME = ; DESC = Indicates the time delay to switch \ from voice to silence.\ (Configuration); HELP = ; CAPABILITIES = ; Enumeration: 'msec700': 7, 'msec300': 3, 'msec800': 8, 'msec400': 4, 'msec500': 5, 'msec100': 1, 'msec600': 6, 'msec200': 2.

NAME = ; DESC = The value of this object represents the \ Idle pattern on the line when no call is up.\ Specific to a PBX. This is a permanent DSP \ configuration parameter; HELP = This value can be used to detect that a call \ has finished and that the echo canceller should \ be reset and that fax mode should be terminated.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the filter \ length for echo canceller. This is a permanent \ DSP configuration parameter.; HELP = A length of 128 is equal to 16ms.\ A length of 256 is equal to 32ms.; ---- NOTE: The ISDN BRI voice card supports 32ms only; CAPABILITIES = ; Enumeration: 'length256': 2, 'length128': 1.

NAME = ; DESC = The value of this object is used for echo \ canceller Er1 improvement. This is a DSP \ Dynamic configuration parameter. \ A signal will be attenuated by this dB \ amount before being passed through the \ echo canceller. After the echo canceller, \ it will be amplified by this same dB amount, \ for a net gain of 0 dB. \ This attenuation amplicfication cycle reduces \ the resolution of the signal ( -18 ..0 ).; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object will suppress the \ impulsive backround noise in order to achieve \ silence suppression savings. HELP = ; CAPABILITIES = ;

NAME = ; DESC = DTMF burst generation in milliseconds.; HELP = ; CAPABILITIES = ; Enumeration: 'time70msec': 3, 'time100msec': 4, 'time50msec': 1, 'time60msec': 2.

NAME = ; DESC = DTMF burst Regeneration length in milliseconds.; HELP = ; CAPABILITIES = ; Enumeration: 'time70msec': 3, 'time100msec': 4, 'time50msec': 1, 'time60msec': 2.

NAME = ; DESC = The VNET Voice Switching Profile Configuration \ table.(Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Switching Profile \ Configuration table. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the profile \ number. Used as an index to the VNET Voice \ Switching Profile Configuration table. \ (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies how to \ handle outgoing calls for voice channel \ switching. (Configuration); HELP = 2: include CUG ID in outgoing call. \ 3: include restriction class in outgoing call. \ 4: include both CUG ID and restriction \ class in outgoing call. \ 5: outgoing call is not allowed.; CAPABILITIES = ; Enumeration: 'closedUserGroupCall': 2, 'restrictionClassCall': 3, 'noRestriction': 1, 'bothCUGandRCCall': 4, 'inhibitAll': 5.

NAME = ; DESC = The value of this object specifies how to \ handle incoming calls for voice channel \ switching. (Configuration); HELP = 2: check CUG ID in incoming call. (Must \ match our CUG ID for call acceptance. \ 3: check RCC in incoming call. (Must be \ greater than or equal to our RCC for call \ acceptance. \ 4: check both CUG and RCC in incoming \ call. \ 5: incoming call is not allowed.; CAPABILITIES = ; Enumeration: 'checkRestrictionClassCode': 3, 'cUGandPublicClassInhibit': 4, 'noRestriction': 1, 'checkCUGID': 2, 'inhibitAll': 5.

NAME = ; DESC = The value of this object assigns the Closed \ User Group ID for a voice channel. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object assigns the Restriction \ Class Code for a voice channel. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object provides a voice \ channel Auto Call destination number by \ specifying an index into the ingress table. \ (Configuration); HELP = 0: auto call disabled. \ 1-32: index to the ingress table entry where \ the dial number is specified. \ The auto call for the ISDN BRI voice card is always \ disabled.; CAPABILITIES = ;

NAME = ; DESC = The value of this object specifies the preference \ for the voice algorithm when an outgoing call is \ made. (Configuration); HELP = specific: whatever is configured. \ bandwidth: bigger block size. \ delay: shorter block size.; CAPABILITIES = ; Enumeration: 'specific': 1, 'delay': 3, 'bandwidth': 2.

NAME = ; DESC = The value of this object assigns the priority \ of the voice data to be transmitted. (Configuration); HELP = 0: lowest priority. \ 15: highest priority.; CAPABILITIES = ;

NAME = ; DESC = Indicates the type of auto-call \ switching to be performed by the \ voice channel.; HELP = ; CAPABILITIES = ; Enumeration: 'masterHootnHoller': 2, 'slaveHootnHoller': 3, 'normal': 1.

NAME = ; DESC = Indicates which DNA server is used.; HELP = ; CAPABILITIES = ; Enumeration: 'nas': 1, 'vncs': 2.

NAME = ; DESC = Indicates the type of call being made.; HELP = ; CAPABILITIES = ; Enumeration: 'enblock-only': 1, 'dynamic': 2.

NAME = ; DESC = The VNET Voice Ingress Digit Filtering \ Configuration table. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Ingress Digit \ Filtering Configuration table. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the index to \ the ingress table. Used as an index to the VNET \ Voice Ingress Digit Filtering Configuration table. \ Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects the digit \ pattern to be matched. (Null terminated \ character string.) (Configuration); HELP = Valid characters are decimal digits, '#', \ '*', '+', '[' and ']' .; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects commands \ to produce the ingress digits for speed dial, \ call redirect, and source ID insertion features. \ (Configuration); HELP = Valid characters are decimal digits, '#', \ '*', 'D', and 'I'.; CAPABILITIES = ;

NAME = ; DESC = The VNET Voice Egress Digit Manipulation \ Configuration table. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Egress Digit \ Manipulation Configuration table. (Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the index to \ the egress table. Used as an index to the VNET \ Voice Egress Digit Manipulation Configuration \ table. Configuration); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects the phone \ number that voice channels are associated with. \ This is the number to be registered to the Address \ Server (RSA). (Configuration); HELP = Valid characters are decimal digits, '#', and '*'.; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects commands \ to produce the egress digits for FXO, E&M, \ or FXS 3-Port interface. The result is the \ number to be sent to the connected phone \ device. (Configuration); HELP = Valid characters are decimal digits, '#', '*', \ '+', 'D', 'H', and 'I'. The character 'H' is \ used to trigger immediate dial handling by the PBX.; CAPABILITIES = ;

NAME = ; DESC = The value of this object selects voice channels \ associated with the phone number. The valid \ string consists of the substring 'B1'~'B6', \ 'C1'~'C12', 'D1'~'D12', and 'E1'~'E2'. \ (Configuration); HELP = Valid characters are decimal digits, 'B', 'C', \ 'D', and 'E'.; CAPABILITIES = ;

NAME = ; DESC = The VNET Voice Channel Control table. \ HELP = ; CAPABILITIES = NET_OPER, VPN_OPER ;

NAME = ; DESC = An entry in the VNET Voice Channel Control \ table.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The card lim (logical interface module) number of a \ particular voice channel. Used as an index to the \ VNET Voice Channel Control table.; HELP = ; CAPABILITIES = ; Enumeration: 'lim2': 3, 'lim3': 4, 'lim1': 2, 'lim4': 5, 'limB': 6, 'limC': 7, 'limD': 8, 'limE': 9.

NAME = ; DESC = The position of the voice channel in the lim. \ Used as an index to the VNET Voice \ Channel Control table.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = Setting this object will perform various \ actions on the specified voice channel. \ Note: Starting with software release 3.0, \ the enumeration clearChannelCounters (2) is \ not supported. The enumeration is included \ here only to support backwards compatibility \ for software versions prior to release 3.0.; HELP = 1: perform hardware reset to DSP. \ 2: clear statistics counter. \ 3: download code to DSP. \ 4: disconnect call. \ 5: set DSP to loopback mode. \ 6: terminate test. \ 7: force connect channel by using the \ auto call number. NOTE: This option is not \ supported by the ISDN BRI voice card.; CAPABILITIES = ; Enumeration: 'forceConnect': 7, 'disconnect': 4, 'resetChannel': 1, 'codeDownload': 3, 'loopbackTest': 5, 'terminateTests': 6, 'clearChannelCounters': 2.

NAME = ; DESC = Setting this object will perform various \ actions on the VNET voice system. \ Note: Starting with software release 3.0, \ the enumerations clearNetworkCounters (1) and \ clearChannelCounters (3) are not supported. \ The enumeration is included here only to support \ backwards compatibility for software versions \ prior to release 3.0.; HELP = 1: clear network statistics counters. \ 2: perform hardware reset to all channels. \ 3: clear all channel statistics counters. \ 4: download code to all channels. \ 5: disconnect all channel's calls. \ 6: set all channels to loopback mode. \ 7: terminate all channel's tests. \ 8: force connect all channels by using the auto call numbers. NOTE: This option is not \ supported by the ISDN BRI voice card.; \ 9: re-register phone number.; CAPABILITIES = NET_OPER, VPN_OPER ; Enumeration: 'resetChannels': 2, 'loopbackTests': 6, 'disconnect': 5, 'reRegisterPhoneNum': 9, 'terminateTests': 7, 'clearChannelCounters': 3, 'download': 4, 'forceConnects': 8, 'clearNetworkCounters': 1.

NAME = ; DESC = The VNET Voice Channel Status Display table. \ HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Channel Status Display \ table.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The card lim (logical interface module) number of \ a particular voice channel. Used as an index to \ the VNET Voice Channel Status Display table.; HELP = ; CAPABILITIES = ; Enumeration: 'lim2': 3, 'lim3': 4, 'lim1': 2, 'lim4': 5, 'limB': 6, 'limC': 7, 'limD': 8, 'limE': 9.

NAME = ; DESC = The position of the voice channel in the lim. \ Used as an index to the VNET Voice \ Channel Status Display table.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the interface \ type of the specified voice channel.; HELP = Upon powerup, the interface type will not be \ available until the DSP software is loaded and its \ status is reported.; CAPABILITIES = ; Enumeration: 'not-available': 1, 'low-cost-loop-start-FXS': 5, 'three-port': 10, 'dvm': 11, 'ground-start-FXO': 9, 'enhanced-EandM': 3, 'enhanced-loop-start-FXO': 4, 'ground-start-FXS': 8, 'bri': 12, 'enhanced-loop-start-FXS': 2, 'low-cost-EandM': 6, 'low-cost-loop-start-FXO': 7.

NAME = ; DESC = The value of this object indicates the command \ interface version ID (CIVID) of the specified voice \ channel. (Note: CIVID is 20 or above.); HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the E&M \ type of the specified voice channel.; HELP = This is for E&M interface channels only. Other \ interface types will show notApplicable.; CAPABILITIES = ; Enumeration: 'typeI': 1, 'typeII': 2, 'typeIII': 3, 'notApplicable': 6, 'typeIV': 4, 'typeV': 5.

NAME = ; DESC = The value of this object indicates the hardware \ module type for the specified DVM voice channel.; HELP = This is for DVM voice channels only. Analog \ voice channels will show notApplicable.; CAPABILITIES = ; Enumeration: 'notApplicable': 3, 'e1': 2, 't1': 1.

NAME = ; DESC = The value of this object indicates the current \ DSP status of the specified voice channel.; HELP = ; CAPABILITIES = ; Enumeration: 'codeDownloadInProgress': 11, 'busyOut': 10, 'downloadFailure': 3, 'forceConnected': 4, 'dead': 1, 'forceConnected-TimedOut': 5, 'notReady': 2, 'pcmChannelNotInstalled': 12, 'idle': 6, 'switchConnected': 8, 'switchDisconnectInProgress': 9, 'switchConnectInProgress': 7.

NAME = ; DESC = The value of this object indicates the current \ channel network connect status of the specified \ voice channel.; HELP = ; CAPABILITIES = ; Enumeration: 'locallyConnected': 3, 'idle': 1, 'disconnectInProgress': 5, 'callInProgress': 2, 'remotelyConnected': 4.

NAME = ; DESC = The value of this object indicates the remote \ voice channel hardware type (corresponding to \ the specified voice channel).; HELP = This will be the NULL string if the specified \ voice channel is not connected.; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the remote \ voice channel node name (corresponding to \ the specified voice channel).; HELP = This will be the NULL string if the specified \ voice channel is not connected.; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the remote \ voice channel number (corresponding to \ the specified voice channel).; HELP = This will be the NULL string if the specified \ voice channel is not connected.; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the remote \ voice channel interface type (corresponding to \ the specified voice channel).; HELP = This will be the NULL string if the specified \ voice channel is not connected.; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the final \ negotiated software version to be run on both \ sides of a voice channel connection.; HELP = This will be 0 if the specified \ voice channel is not connected.; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the final \ negotiated voice algorithm running on both \ sides of a voice channel connection.; HELP = This will be the NULL string if the specified \ voice channel is not connected.; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the final \ negotiated voice fax algorithm and maximum \ speed running on both sides of a voice fax \ channel connection.; HELP = This will be the NULL string if the specified \ voice fax channel is not connected.; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the final \ negotiated voice modem algorithm and maximum \ speed running on both sides of a voice modem \ channel connection.; HELP = This will be the NULL string if the specified \ voice fax channel is not connected.; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the results \ of a self test performed on the specified voice \ channel.; HELP = ; CAPABILITIES = ; Enumeration: 'testFailed': 2, 'testPassed': 1.

NAME = ; DESC = The value of this object indicates the current \ flash EPROM status in the DSP of the specified \ voice channel.; HELP = ; CAPABILITIES = ; Enumeration: 'erased': 3, 'notInstalled': 1, 'securityViolation': 6, 'noAnalogInterfaceDriver': 5, 'valid': 2, 'invalidChecksum': 4.

NAME = ; DESC = The value of this object indicates the current \ EPROM status in the DSP of the specified voice \ channel.; HELP = ; CAPABILITIES = ; Enumeration: 'currentlyOperating': 2, 'notInstalled': 1, 'presentButNotOperating': 3.

NAME = ; DESC = The value of this object indicates the DSP PROM \ version of the specified voice channel.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the PROM \ ID of the specified voice channel.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the input \ level of the specified voice channel.; HELP = ; CAPABILITIES = ; Enumeration: 'neg1dBm': 14, 'greaterThan0dBm': 16, 'neg6dBm': 9, 'neg21dBm': 3, 'neg8dBm': 8, 'neg3dBm': 12, 'neg2dBm': 13, 'neg5dBm': 10, 'neg4dBm': 11, 'notApplicable': 17, 'neg10dBm': 7, 'neg15dBm': 5, 'lessThanNeg25dBm': 1, 'neg18dBm': 4, 'zerodBm': 15, 'neg12dBm': 6, 'neg24dBm': 2.

NAME = PhoneRegistrationStatus; DESC = Indicates current communications \ status with NAS; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG; Enumeration: 'nasAddressNotConfigured': 3, 'registrationInProgress': 2, 'noResponseFromNAS': 5, 'registrationFailed': 6, 'lostCommunicationWithNAS': 4, 'registrationComplete': 1.

NAME = ; DESC = The VNET Voice Channel Statistics Display table. \ HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;

NAME = ; DESC = An entry in the VNET Voice Channel Statistics \ Display table.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The card lim (logical interface module) number of a \ particular voice channel. Used as an index to the \ VNET Voice Channel Statistics Display table.; HELP = ; CAPABILITIES = ; Enumeration: 'lim2': 3, 'lim3': 4, 'lim1': 2, 'lim4': 5, 'limB': 6, 'limC': 7, 'limD': 8, 'limE': 9.

NAME = ; DESC = The position of the voice channel in the lim. \ Used as an index to the VNET Voice \ Channel Statistics Display table.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ connection time (in sec) since the last statistics \ reset for the specified voice channel outgoing \ calls. (Excludes call setup time and local calls.) ; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ connection time (in sec) since the last statistics \ reset for the specified voice channel incoming \ calls. (Excludes local calls.) ; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of positive call responses sent from the \ remote DSP since the last statistics reset \ for the specified voice channel. (Excludes \ local calls.) ; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of negative call responses sent from the \ remote DSP since the last statistics reset \ for the specified voice channel. (Excludes \ local calls.) ; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of positive call responses sent to the \ remote DSP since the last statistics reset \ for the specified voice channel. (Excludes \ local calls.) ; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of negative call responses sent to the \ remote DSP since the last statistics reset \ for the specified voice channel. (Excludes \ local calls.) ; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of resets sent to the DSP corresponding \ to the specified voice channel.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of no responses sent from the DSP \ since the last DSP reset corresponding \ to the specified voice channel.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of frames with Bad Byte Count received \ from the DSP corresponding to the specified \ voice channel.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of frames with Bad End Of Frame \ character received from the DSP corresponding \ to the specified voice channel.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of speech frames sent by the remote \ that were lost since power up corresponding \ to the specified voice channel.; HELP = Always 0 if sequence number in speech frame \ is not used.; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of control frames sent by the remote \ that were lost corresponding to the specified \ voice channel.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of payload frames received from the \ remote with bad length or frame type \ corresponding to the specified voice channel.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of PUMP messages received from the \ remote with unknown message type, IEs, or \ invalid length corresponding to the specified \ voice channel.; HELP = ; CAPABILITIES = ;

NAME = ; DESC = The value of this object indicates the total \ number of successful SVC calls since the \ last network statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = The value of this object indicates the total \ number of unsuccessful SVC calls since the \ last network statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = The value of this object indicates the total \ number of SVC calls accepted by this access device \ since the last network statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = The value of this object indicates the total \ number of SVC calls rejected by this access device \ since the last network statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = The value of this object indicates the total \ number of successful DNA requests received \ by this access device since the last network \ statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = The value of this object indicates the total \ number of unsuccessful DNA requests received \ by this access device since the last network \ statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = The value of this object indicates the total \ number of streams buffers not available \ to this access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = The value of this object indicates the total \ number of calls in progress or connected \ in this access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;

NAME = ; DESC = Indicates that a failure occurred while \ downloading the voice image.\ Severity Level: MAJOR.; HELP = Downloading the voice image failed. Retry again, and if problem \ persists, please contact system admin., or field \ Personnel.;

NAME = ; DESC = Indicates that the DSP is not running. \ A channel reset may be required.; HELP = DSP is not running. Reset voice channel(s). If problem still exist, \ contact sys admin. or Field Personnel.;

NAME = ; DESC = Indicates recovery from the out of order condition.\ Severity Level: CRITICAL.; HELP = DSP is running. Normal status indication.;

NAME = ; DESC = Indicates that the DSP is running, \ but unable to sync up. A channel reset \ may be required.\ Severity Level: MAJOR.; HELP = Reset channel(s). If Synchronization is not acquired, \ contact sys admin., or Field Personnel.;

NAME = ; DESC = Indicates recovery from the failure to \ sync up condition.\ Severity Level: INFORMATIVE. ; HELP = Synchronization is acquired. Normal Status Indicator.;

NAME = ; DESC = Indicates that the built image doesn't \ contain CVM code\ Severity Level: MAJOR.; HELP = Access device code does not contain image for CVM module. \ Please contact Sys Admin., or Field Personnel. ;

NAME = ; DESC = Indicates that the built image doesn't \ contain TUVM code.\ Severity Level: MAJOR.; HELP = Access device code does not contain image for TUVM module. \ Please contact Sys Admin., or Field Personnel. ;

NAME = ; DESC = Indicates that the built image doesn't \ contain DVM code.\ Severity Level: MAJOR.; HELP = Access device code does not contain image for DVM module. \ Please contact Sys Admin., or Field Personnel. ;