DKSF-70-4-X-X-1: View SNMP OID List / Download MIB

VENDOR: ZAO LIGHT COMMUNICATION


 Home MIB: DKSF-70-4-X-X-1
Download as:   
SNMPv2-CONF, SNMPv2-SMI, SNMPv2-TC, SNMPv2-MIB

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 lightcom 1.3.6.1.4.1.25728
             uniPingServerSolutionV3 1.3.6.1.4.1.25728.70
Generic MIB for NetPing remote sensing and control
             npTrapInfo 1.3.6.1.4.1.25728.90
                   npTrapEmailTo 1.3.6.1.4.1.25728.90.1 displaystring read-only
user-specified e-mail for NetPing Trap Forwarding Service
             npReboot 1.3.6.1.4.1.25728.911
                     npSoftReboot 1.3.6.1.4.1.25728.911.1 integer read-write
Write 1 to reboot device after current operations completition
                     npResetStack 1.3.6.1.4.1.25728.911.2 integer read-write
Write 1 to re-initialize network stack
                     npForcedReboot 1.3.6.1.4.1.25728.911.3 integer read-write
Write 1 to immediate forced reboot
             npGsm 1.3.6.1.4.1.25728.3800
                       npGsmInfo 1.3.6.1.4.1.25728.3800.1
                           npGsmFailed 1.3.6.1.4.1.25728.3800.1.1 integer read-only
Firmware's GSM module status Enumeration: 'failed': 1, 'ok': 0, 'fatalError': 2.
                           npGsmRegistration 1.3.6.1.4.1.25728.3800.1.2 integer read-only
Status of modem registration in GSM network (AT+CREG? result) Enumeration: 'infoUpdate': 255, 'unknown': 4, 'searching': 2, 'denied': 3, 'impossible': 0, 'roaming': 5, 'homeNetwork': 1.
                           npGsmStrength 1.3.6.1.4.1.25728.3800.1.3 integer read-only
GSM signal strength. 0..31 = 0..100%, 99 = unknown or n/a, 255 = updating info
                           npGsmSendSms 1.3.6.1.4.1.25728.3800.1.9 displaystring read-write
Send arbitrary SMS. Format: [phone_number,phone_number,...] Message One to four destination phone numbers If [] and numbers omitted, mesagge will be sent to preset numbers from SMS setup Only Latin characters allowed in message body
                       npGsmTraps 1.3.6.1.4.1.25728.3800.2
                           npGsmTrapPrefix 1.3.6.1.4.1.25728.3800.2.0
                               npGsmTrap 1.3.6.1.4.1.25728.3800.2.0.1
GSM modem or SMS firmware problems
             npRelay 1.3.6.1.4.1.25728.5500
                       npRelayTable 1.3.6.1.4.1.25728.5500.5 no-access
Watchdog and outlet/relay control table
                           npRelayEntry 1.3.6.1.4.1.25728.5500.5.1 no-access
Relay/outlet table row
                               npRelayN 1.3.6.1.4.1.25728.5500.5.1.1 integer read-only
The N of output relay
                               npRelayMode 1.3.6.1.4.1.25728.5500.5.1.2 integer read-write
Control of relay: -1 - flip between on(1) and off(0) 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - both schedule and watchdog (while switched on by schedule) 5 - logic Enumeration: 'on': 1, 'off': 0, 'schedule': 3, 'flip': -1, 'logic': 5, 'scheduleAndWatchdog': 4, 'watchdog': 2.
                               npRelayStartReset 1.3.6.1.4.1.25728.5500.5.1.3 integer read-write
Write 1 to start reset (switch relay off for some time)
                               npRelayMemo 1.3.6.1.4.1.25728.5500.5.1.6 displaystring read-only
Relay memo
                               npRelayState 1.3.6.1.4.1.25728.5500.5.1.15 integer read-only
Actual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is on Enumeration: 'on': 1, 'off': 0.
             npIr 1.3.6.1.4.1.25728.7900
                       npIrCtrl 1.3.6.1.4.1.25728.7900.1
                           npIrPlayCmd 1.3.6.1.4.1.25728.7900.1.1 integer read-write
Write IR command number to send IR command
                           npIrReset 1.3.6.1.4.1.25728.7900.1.2 integer read-write
Write 1 to reset IR transiever. After reset, send IR command and check npIrStatus.
                           npIrStatus 1.3.6.1.4.1.25728.7900.1.3 integer read-only
IR transiever status Enumeration: 'commandCompleted': 0, 'commandAccepted': 2, 'errorFlashChip': 19, 'errorTimeout': 20, 'errorUnknown': 16, 'errorExtBusBusy': 21, 'errorEmptyRecord': 18, 'errorBadNumber': 17, 'protocolError': 1.
             npCurLoop 1.3.6.1.4.1.25728.8300
                       npCurLoopTable 1.3.6.1.4.1.25728.8300.1 no-access
Current loop sensors Table
                           npCurLoopEntry 1.3.6.1.4.1.25728.8300.1.1 no-access
Current loop sensors Table Row
                               npCurLoopN 1.3.6.1.4.1.25728.8300.1.1.1 integer read-only
Index of current loop, 1 to max supported
                               npCurLoopStatus 1.3.6.1.4.1.25728.8300.1.1.2 integer read-only
Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered Enumeration: 'short': 3, 'cut': 2, 'ok': 0, 'notPowered': 4, 'alert': 1.
                               npCurLoopI 1.3.6.1.4.1.25728.8300.1.1.3 integer read-only
Loop current, mA
                               npCurLoopV 1.3.6.1.4.1.25728.8300.1.1.4 integer read-only
Voltage drop on the loop, mV
                               npCurLoopR 1.3.6.1.4.1.25728.8300.1.1.5 integer read-only
Resistance of the loop, Ohm
                               npCurLoopPower 1.3.6.1.4.1.25728.8300.1.1.7 integer read-write
Control of loop power 0=Off, 1=On, 2=reset by off/on power Enumeration: 'on': 1, 'off': 0, 'cyclePower': 2.
                       npCurLoopTraps 1.3.6.1.4.1.25728.8300.2
                           npCurLoopTrapPrefix 1.3.6.1.4.1.25728.8300.2.0
                               npCurLoopTrap 1.3.6.1.4.1.25728.8300.2.0.1
Status of current loop N has changed!
                           npCurLoopTrapN 1.3.6.1.4.1.25728.8300.2.1 integer read-only
Index of current loop, which status has changed
                           npCurLoopTrapStatus 1.3.6.1.4.1.25728.8300.2.2 integer read-only
Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered Enumeration: 'short': 3, 'cut': 2, 'ok': 0, 'notPowered': 4, 'alert': 1.
                           npCurLoopTrapI 1.3.6.1.4.1.25728.8300.2.3 integer read-only
Loop current, mA
                           npCurLoopTrapV 1.3.6.1.4.1.25728.8300.2.4 integer read-only
Voltage drop on the loop, mV
                           npCurLoopTrapR 1.3.6.1.4.1.25728.8300.2.5 integer read-only
Resistance of the loop, Ohm
                           npCurLoopTrapPower 1.3.6.1.4.1.25728.8300.2.7 integer read-write
Status of loop power 0=Off, 1=On Enumeration: 'on': 1, 'off': 0.
             npRelHumidity 1.3.6.1.4.1.25728.8400
                       npRelHumSensor 1.3.6.1.4.1.25728.8400.2
                           npRelHumSensorValueH 1.3.6.1.4.1.25728.8400.2.2 integer read-only
Relative humidity value, %
                           npRelHumSensorStatus 1.3.6.1.4.1.25728.8400.2.3 integer read-only
Status of the Rel.Humidity Sensor One 1=Normal, 0=Error or Sensor isn't connected Enumeration: 'ok': 1, 'error': 0.
                           npRelHumSensorValueT 1.3.6.1.4.1.25728.8400.2.4 integer read-only
Sensor temperature, deg.C
                           npRelHumSensorStatusH 1.3.6.1.4.1.25728.8400.2.5 integer read-only
Status of Relative Humiduty Enumeration: 'sensorFailed': 0, 'aboveSafeRange': 3, 'inSafeRange': 2, 'belowSafeRange': 1.
                           npRelHumSafeRangeHigh 1.3.6.1.4.1.25728.8400.2.7 integer read-only
Relative Humidity safe range, top margin, %RH
                           npRelHumSafeRangeLow 1.3.6.1.4.1.25728.8400.2.8 integer read-only
Relative Humidity safe range, bottom margin, %RH
                           npRelHumSensorValueT100 1.3.6.1.4.1.25728.8400.2.9 integer32 read-only
Sensor temperature, deg.C * 100 (fixed point two decimal places) Used to get access to the fractional part of T value
                       npRelHumTraps 1.3.6.1.4.1.25728.8400.9
                           npRelHumTrapPrefix 1.3.6.1.4.1.25728.8400.9.0
                               npRelHumTrap 1.3.6.1.4.1.25728.8400.9.0.1
Status of Relative Humidity RH sensor has changed!
             npThermo 1.3.6.1.4.1.25728.8800
                       npThermoTable 1.3.6.1.4.1.25728.8800.1 no-access
Thermo Sensors Table
                           npThermoEntry 1.3.6.1.4.1.25728.8800.1.1 no-access
Thermo Sensors Table Row
                               npThermoSensorN 1.3.6.1.4.1.25728.8800.1.1.1 integer read-only
The id of temperature sensor, 1 to 8
                               npThermoValue 1.3.6.1.4.1.25728.8800.1.1.2 integer read-only
Temperature, deg.C
                               npThermoStatus 1.3.6.1.4.1.25728.8800.1.1.3 integer read-only
Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat) Enumeration: 'high': 3, 'failed': 0, 'low': 1, 'norm': 2.
                               npThermoLow 1.3.6.1.4.1.25728.8800.1.1.4 integer read-only
Bottom margin of normal temperature range, deg.C
                               npThermoHigh 1.3.6.1.4.1.25728.8800.1.1.5 integer read-only
Top margin of normal temperature range, deg.C
                               npThermoMemo 1.3.6.1.4.1.25728.8800.1.1.6 displaystring read-only
T channel memo
                       npThermoTraps 1.3.6.1.4.1.25728.8800.2
                           npThermoTrapPrefix 1.3.6.1.4.1.25728.8800.2.0
                               npThermoTrap 1.3.6.1.4.1.25728.8800.2.0.1
Status of Thermo sensor is changed (crossing of normal temp. range)
                           npThermoTrapSensorN 1.3.6.1.4.1.25728.8800.2.1 integer read-only
The id of temperature sensor, 1 to 8
                           npThermoTrapValue 1.3.6.1.4.1.25728.8800.2.2 integer read-only
Temperature, deg.C
                           npThermoTrapStatus 1.3.6.1.4.1.25728.8800.2.3 integer read-only
Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat) Enumeration: 'high': 3, 'failed': 0, 'low': 1, 'norm': 2.
                           npThermoTrapLow 1.3.6.1.4.1.25728.8800.2.4 integer read-only
Bottom margin of normal temperature range, deg.C
                           npThermoTrapHigh 1.3.6.1.4.1.25728.8800.2.5 integer read-only
Top margin of normal temperature range, deg.C
                           npThermoTrapMemo 1.3.6.1.4.1.25728.8800.2.6 displaystring read-only
T channel memo
             npIo 1.3.6.1.4.1.25728.8900
                       npIoTable 1.3.6.1.4.1.25728.8900.1 no-access
Digital Input/output Table
                           npIoEntry 1.3.6.1.4.1.25728.8900.1.1 no-access
Digital Input/output Table Row
                               npIoLineN 1.3.6.1.4.1.25728.8900.1.1.1 integer read-only
Number of IO line, from 1 to max supported
                               npIoLevelIn 1.3.6.1.4.1.25728.8900.1.1.2 integer read-only
Input level, 0 or 1
                               npIoLevelOut 1.3.6.1.4.1.25728.8900.1.1.3 integer read-write
Output level, 0 or 1. Write -1 to flip output. Enumeration: 'high': 1, 'flip': -1, 'low': 0.
                               npIoMemo 1.3.6.1.4.1.25728.8900.1.1.6 displaystring read-only
IO line memo
                               npIoPulseCounter 1.3.6.1.4.1.25728.8900.1.1.9 counter32 read-write
Pulse Counter on IO input line (counts positive fronts) Write 0 to reset.
                               npIoSinglePulseDuration 1.3.6.1.4.1.25728.8900.1.1.12 integer read-write
Set duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100ms
                               npIoSinglePulseStart 1.3.6.1.4.1.25728.8900.1.1.13 integer read-write
Write 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDuration
                       npIoTraps 1.3.6.1.4.1.25728.8900.2
                           npIoTrapPrefix 1.3.6.1.4.1.25728.8900.2.0
                               npIoTrap 1.3.6.1.4.1.25728.8900.2.0.1
Input state of IO line is changed
                           npIoTrapLineN 1.3.6.1.4.1.25728.8900.2.1 integer read-only
Trap data, Number of IO line
                           npIoTrapLevelIn 1.3.6.1.4.1.25728.8900.2.2 integer read-only
Trap data, new Input level, 0 or 1
                           npIoTrapMemo 1.3.6.1.4.1.25728.8900.2.6 displaystring read-only
Trap data, IO line memo
                           npIoTrapLevelLegend 1.3.6.1.4.1.25728.8900.2.7 displaystring read-only
Legend for current logic level on the IO line