ZYXEL-ACL-MIB: View SNMP OID List / Download MIB

VENDOR: ZYXEL COMMUNICATIONS CORP.


 Home MIB: ZYXEL-ACL-MIB
Download as:   
SNMPv2-CONF, ZYXEL-ES-SMI, SNMPv2-SMI, P-BRIDGE-MIB, INET-ADDRESS-MIB, Q-BRIDGE-MIB, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 zyxelAcl 1.3.6.1.4.1.890.1.15.3.10
The subtree for access control list (ACL)
       zyxelClassifierStatus 1.3.6.1.4.1.890.1.15.3.10.1
           zyxelClassifierTable 1.3.6.1.4.1.890.1.15.3.10.1.1 no-access
The table contains classifier configuration.
               zyxelClassifierEntry 1.3.6.1.4.1.890.1.15.3.10.1.1.1 no-access
An entry contains classifier configuration.
                   zyClassifierName 1.3.6.1.4.1.890.1.15.3.10.1.1.1.1 displaystring no-access
The name of classifier rule is used for identifying purposes.
                   zyClassifierState 1.3.6.1.4.1.890.1.15.3.10.1.1.1.2 enabledstatus read-only
Enable/Disable classifier rule on this switch.
                   zyClassifierPacketFormat 1.3.6.1.4.1.890.1.15.3.10.1.1.1.3 integer read-only
Packet format for classifier rule. A value of 802.3 indicates that the packets are formatted according to the IEEE 802.3 standards. A value of Ethernet II indicates that the packets are formatted according to RFC 894, Ethernet II encapsulation. Enumeration: 'ethernetIIUntagged': 2, 'ethernet802dot3Tagged': 5, 'all': 1, 'ethernet802dot3Untagged': 4, 'ethernetIITagged': 3.
                   zyClassifierVid 1.3.6.1.4.1.890.1.15.3.10.1.1.1.4 integer read-only
Source VLAN ID for classifier rule. The range is 1~4094 and value 0 means any VLAN.
                   zyClassifier8021pPriority 1.3.6.1.4.1.890.1.15.3.10.1.1.1.5 integer read-only
802.1p priority for classifier rule. 0~7. The range is 0~7 and value -1 means any priority level.
                   zyClassifierEthernetType 1.3.6.1.4.1.890.1.15.3.10.1.1.1.6 integer read-only
Ethernet type for classifier rule. It is represented in decimal expression and value 65535 means any Ethernet type.
                   zyClassifierSourceMacAddress 1.3.6.1.4.1.890.1.15.3.10.1.1.1.7 macaddress read-only
Source MAC address for classifier rule. 00:00:00:00:00:00 means any source MAC address.
                   zyClassifierIncomingPort 1.3.6.1.4.1.890.1.15.3.10.1.1.1.8 integer read-only
Incoming Port for classifier rule. Value 65536 means any port.
                   zyClassifierDestinationMacAddress 1.3.6.1.4.1.890.1.15.3.10.1.1.1.9 macaddress read-only
Destination MAC address for classifier rule. 00:00:00:00:00:00 means any destination MAC address.
                   zyClassifierDSCP 1.3.6.1.4.1.890.1.15.3.10.1.1.1.10 integer read-only
DSCP (DiffServ Code Point) for classifier rule. The range is 0~63 and value -1 means any DSCP.
                   zyClassifierIpProtocol 1.3.6.1.4.1.890.1.15.3.10.1.1.1.11 integer read-only
IP Protocol for classifier rule. Value 255 means any IP protocol.
                   zyClassifierEstablishOnly 1.3.6.1.4.1.890.1.15.3.10.1.1.1.12 enabledstatus read-only
Establish Only for TCP protocol type in classifier rule. This means that the switch will pick out the packets that are sent to establish TCP connections.
                   zyClassifierSourceIpAddress 1.3.6.1.4.1.890.1.15.3.10.1.1.1.13 ipaddress read-only
Source IP address for classifier rule. 0.0.0.0 means any source IP address.
                   zyClassifierSourceIpMaskBits 1.3.6.1.4.1.890.1.15.3.10.1.1.1.14 integer read-only
Source IP mask bits for classifier rule.
                   zyClassifierSourceSocket 1.3.6.1.4.1.890.1.15.3.10.1.1.1.15 integer read-only
Source socket number for classifier rule. Value 0 means any socket number.
                   zyClassifierDestinationIpAddress 1.3.6.1.4.1.890.1.15.3.10.1.1.1.16 ipaddress read-only
Destination IP address for classifier rule. 0.0.0.0 means any destination IP address.
                   zyClassifierDestinationIpMaskBits 1.3.6.1.4.1.890.1.15.3.10.1.1.1.17 integer read-only
Destination IP mask bits for classifier rule.
                   zyClassifierDestinationSocket 1.3.6.1.4.1.890.1.15.3.10.1.1.1.18 integer read-only
Destination socket number for classifier rule. Value 0 means any socket number.
                   zyClassifierIPv6DSCP 1.3.6.1.4.1.890.1.15.3.10.1.1.1.19 integer read-only
DSCP (DiffServ Code Point) for classifier rule. The range is 0~63 and value -1 means any DSCP.
                   zyClassifierIPv6NextHeader 1.3.6.1.4.1.890.1.15.3.10.1.1.1.20 integer read-only
IPv6 next header protocol type for classifier rule. Value 255 means any protocol type.
                   zyClassifierIPv6EstablishOnly 1.3.6.1.4.1.890.1.15.3.10.1.1.1.21 enabledstatus read-only
Establish Only for TCP protocol type in classifier rule. This means that the switch will pick out the packets that are sent to establish TCP connections.
                   zyClassifierIPv6SourceIpAddress 1.3.6.1.4.1.890.1.15.3.10.1.1.1.22 inetaddress read-only
IPv6 source address for classifier rule. :: means any IPv6 source ip address.
                   zyClassifierIPv6SourceIpPrefixLength 1.3.6.1.4.1.890.1.15.3.10.1.1.1.23 integer read-only
IPv6 source address prefix length for classifier rule.
                   zyClassifierIPv6DestinationIpAddress 1.3.6.1.4.1.890.1.15.3.10.1.1.1.24 inetaddress read-only
IPv6 destination address for classifier rule. :: means any IPv6 destination ip address.
                   zyClassifierIPv6DestinationIpPrefixLength 1.3.6.1.4.1.890.1.15.3.10.1.1.1.25 integer read-only
IPv6 destination address prefix length for classifier rule.
                   zyClassifierRowstatus 1.3.6.1.4.1.890.1.15.3.10.1.1.1.26 rowstatus read-only
This object shows the entry of classifier rule status.
       zyxelPolicyStatus 1.3.6.1.4.1.890.1.15.3.10.2
           zyxelPolicyTable 1.3.6.1.4.1.890.1.15.3.10.2.1 no-access
The table contains policy configuration.
               zyxelPolicyEntry 1.3.6.1.4.1.890.1.15.3.10.2.1.1 no-access
An entry contains policy configuration.
                   zyPolicyName 1.3.6.1.4.1.890.1.15.3.10.2.1.1.1 displaystring no-access
The name of policy rule is used for identifying purposes.
                   zyPolicyState 1.3.6.1.4.1.890.1.15.3.10.2.1.1.2 enabledstatus read-only
Enable/Disable policy rule on this switch.
                   zyPolicyClassifier 1.3.6.1.4.1.890.1.15.3.10.2.1.1.3 displaystring read-only
The classifier(s) applies in this policy rule.
                   zyPolicyVid 1.3.6.1.4.1.890.1.15.3.10.2.1.1.4 integer read-only
VLAN ID for policy rule.
                   zyPolicyEgressPort 1.3.6.1.4.1.890.1.15.3.10.2.1.1.5 integer read-only
The outgoing port number in this policy rule.
                   zyPolicy8021pPriority 1.3.6.1.4.1.890.1.15.3.10.2.1.1.6 integer read-only
Specify a 802.1p priority level for policy rule. The value of 802.1p is between 0 and 7.
                   zyPolicyDSCP 1.3.6.1.4.1.890.1.15.3.10.2.1.1.7 integer read-only
Specify a DSCP (DiffServ Code Point) for policy rule. DSCP number is between 0 and 63.
                   zyPolicyTOS 1.3.6.1.4.1.890.1.15.3.10.2.1.1.8 integer read-only
Specify the type of service (TOS) priority level for policy rule. The value of TOS is between 0 and 7.
                   zyPolicyBandwidth 1.3.6.1.4.1.890.1.15.3.10.2.1.1.9 integer read-only
Specify the bandwidth for policy rule in kilobit per second (Kbps).
                   zyPolicyOutOfProfileDSCP 1.3.6.1.4.1.890.1.15.3.10.2.1.1.10 integer read-only
Specify a new DSCP number (between 0 and 63) for policy rule if you want to replace or remark the DSCP number for out-of-profile traffic.
                   zyPolicyForwardingAction 1.3.6.1.4.1.890.1.15.3.10.2.1.1.11 integer read-only
There are three forwarding actions for policy rule. 'No change' is forward the packets. 'Discard the packet' is drop the packets. 'Do not drop the matching frame previously marked for dropping' is retain the frames that were marked to be dropped before. Enumeration: 'noChange': 1, 'doNotDropTheMatchingFramePreviouslyMarkedForDropping': 3, 'discardThePacket': 2.
                   zyPolicyPriorityAction 1.3.6.1.4.1.890.1.15.3.10.2.1.1.12 integer read-only
There are four priority actions for policy rule. 'No change' is keep the priority setting of the frames. 'Set the packet's 802.1 priority' is replace the packet's 802.1 priority field with the value you set in the Priority field. 'Send the packet to priority queue' is put the packets in the designated queue. 'Replace the 802.1 priority field with the IP TOS value' to replace the packet's 802.1 priority field with the value you set in the TOS field. Enumeration: 'noChange': 1, 'replaceThe802dot1PriorityFieldWithTheIpTosValue': 4, 'setThePackets802dot1Priority': 2, 'sendThePacketToPriorityQueue': 3.
                   zyPolicyDiffServAction 1.3.6.1.4.1.890.1.15.3.10.2.1.1.13 integer read-only
There are four DiffServ actions for policy rule. 'No change' is keeping the TOS and/or DSCP fields in the packets. 'Set the packet's TOS field' is set the TOS field with the value you configure in the TOS field. 'Replace the IP TOS with the 802.1 priority value' is replace the TOS field with the value you configure in the Priority field. 'Set the Diffserv Codepoint field in the frame' to set the DSCP field with the value you configure in the DSCP field. Enumeration: 'noChange': 1, 'setTheDiffservCodepointFieldInTheFrame': 4, 'replaceTheIpTosFieldWithThe802dot1PriorityValue': 3, 'setThePacketsTosField': 2.
                   zyPolicyOutgoingAction 1.3.6.1.4.1.890.1.15.3.10.2.1.1.14 bits read-only
There are four outgoing actions for policy rule. 'Send the packet to the mirror port' is sent the packet to the mirror port. 'Send the packet to the egress port' is sent the packet to the egress port. 'Send the matching frames to the egress port' is sent the matching policy rule frames to the egress port. 'Set the packets VLAN ID' is set packet with tag. Bits: 'sendThePacketToTheEgressPort': 1, 'setThePacketVlanId': 3, 'sendTheMatchingFramesToTheEgressPort': 2, 'sendThePacketToTheMirrorPort': 0.
                   zyPolicyMeteringState 1.3.6.1.4.1.890.1.15.3.10.2.1.1.15 integer read-only
Enable/Disable bandwidth limitation on the traffic flow(s) then set the actions to be taken on out-of-profile packets.
                   zyPolicyOutOfProfileAction 1.3.6.1.4.1.890.1.15.3.10.2.1.1.16 bits read-only
There are four out of profile actions for policy rule. 'Drop the packet' is discard the out-of-profile traffic. 'Change the DSCP value' is replace the DSCP field with the value specified in the Out of profile DSCP field. 'Set Out-Drop Precedence' is mark out-of-profile traffic and drop it when network is congested. 'Do not drop the matching frame previously marked for dropping' to queue the frames that are marked to be dropped. Bits: 'changeTheDscpValue': 1, 'dropThePacket': 0, 'doNotDropTheMatchingFramePreviouslyMarkedForDropping': 3, 'setOutDropPrecedence': 2.
                   zyPolicyRowstatus 1.3.6.1.4.1.890.1.15.3.10.2.1.1.17 rowstatus read-only
This object shows the entry of policy rule status.