ZTE-AN-GPON-ONUPRF-MIB: View SNMP OID List / Download MIB

The MIB module for the management of GPON ONU profile.

The ONU profile T-CONT table.

The ONU profile T-CONT entry.

Name of ONU profile.

An arbitrary (unique) integer for identifying an entry in the table, from 1 to upper limit supported T-CONT count of ONU type.

Name of the T-CONT.

The name of profile used by T-CONT bandwidth configuration.

The DBA gap mode. For GPON ONU, the explanations of these modes are as follows: mode0 is one frame, mode1 is two frames, mode2 is four frames, mode3 is eight frames. default is the system default policy. For example, 'two frames' indicates that T-CONT will perform DBA in a gap of two data frames. Enumeration: 'default': 11, 'mode2': 3, 'mode3': 4, 'mode0': 1, 'mode1': 2.

The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile GEM port table.

The ONU profile GEM port entry.

An arbitrary (unique) integer for identifying an entry in the table, from 1 to upper limit supported GEM port count of ONU type.

Name of the GEM port.

It is equal to the 'zxAnGponOPTcontIndex' of 'zxAnGponOPTcontTable'.

The queue (index from 0 to 7) of T-CONT for this GEM port. Queue 7 is the highest priority queue.

The encrypt state of this GEM port. Enumeration: 'bothDirectEncrypt': 3, 'noEncrypt': 2, 'downstreamEncrypt': 1.

The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). In particular, a newly created row cannot be created until the corresponding 'zxAnGponOPGemPortTcontIndex' has been set. To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile mapping table.

The ONU profile mapping entry.

Name of service.

GEM port index of service.

4bytes value contains:type (MSB 2bytes)/ifId (LSB 2bytes). type means 0 bridge 1 ethuni 2 iphost 3 wifiuni 4 veip 5 wan If type is 'bridge', then the 2-byte ifId has no meaning, just keep it zero; If type is 'ethuni', then the 2-byte ifId contains: slot (MSB 1byte)/port (LSB 1byte); If type is 'iphost', then the 2-byte ifId means the ID of iphost, range from 1 to 255; If type is 'wifiuni', then the 2-byte ifId contains: slot (MSB 1byte)/port (LSB 1byte); If type is 'veip', then the 2-byte ifId means the ID of VEIP, range from 1 to 255; If type is 'wan', then the 2-byte ifId means the ID of WAN, range from 1 to 255.

Map type of service. - cos: mapping to GEM port by CoS value - vlan: mapping to GEM port by VLAN value - cosAndVlan: mapping to GEM port by both cos and VLAN value - transparent: mapping to GEM port transparently - untag: mapping to GEMP port for untag frames Enumeration: 'cosAndVlan': 3, 'cos': 1, 'vlan': 2, 'transparent': 4, 'untag': 5.

A bitfield defines the frames with the priority related with this service. MSB stands for priority 7, LSB stands for priority 0. A bit value of 0 specifies that frames with the associated priority are to be discarded.

Each 2 bytes stand for the VLAN ID related with this service. The first N*2 bytes are valid, until VLAN ID=0.

The status of this conceptual row. The state of this conceptual row only support 'not exist' and 'active'. The action of this conceptual row only support 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables usage rules in 'zxAnGponOPMappingEntry' description. To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile ONU configuration table.

The ONU profile ONU configuration entry.

The VPort mode. gemport(1): a related VPort will be created automatically when a GEM port is created. manual(3): VPort will be created manually. Enumeration: 'manual': 3, 'gemport': 1.

Enables or disables the ONU upstream FEC function. enabled(1): enable the ONU upstream FEC function. disabled(2): disable the ONU upstream FEC function. auto(3): system will enable or disable the ONU upstream FEC function automatically according to the system automation rule. default(4): system will enable or disable the ONU upstream FEC function according to the system default rule. Enumeration: 'disabled': 2, 'auto': 3, 'default': 4, 'enabled': 1.

The ONU profile VPort table.

The ONU profile VPort entry.

VPort ID.

Name of the VPort.

Map type of GEM port and VPort. cos(1): mapping by CoS value. vlan(2): mapping by VLAN value. cosPlusVlan(3): mapping by CoS and VLAN value. oneToOne(4): mapping is 1:1 between GEM port and VPort. Enumeration: 'cosPlusVlan': 3, 'cos': 1, 'vlan': 2, 'oneToOne': 4.

The status of this conceptual row. The supported actions of this conceptual row only include: To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile VPort mapping table.

The ONU profile VPort mapping entry.

A CoS value (0..7) referenced by a GEM port mapped to a VPort.

A VLAN ID referenced by a GEM port mapped to a VPort. The value 65535 indicates the untagged frames. When VPort mapping type is oneToOne(4) or cos(1), this value is 0.

The status of this conceptual row. The supported actions of this conceptual row only include: To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile T-CONT queue schedule table.

The ONU profile T-CONT queue schedule entry.

The T-CONT queue schedule profile name, this profile is defined in zxAnGponRmTrafficSchedPrfTable. The empty string indicates that no profile is bound to this T-CONT.

The ONU profile GPON GEM port current performance table.

The ONU profile GPON GEM port current performance entry.

The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile port VLAN table. A table containing VLAN port information for VLANs configured into the bridge by (local or network) management, specifying the set of ports to which frames received on a VLAN for this FDB and containing a specific Group destination address are allowed to be forwarded. When a manager wants to create a VLAN port,it must comply with the multi-variables usage rule that all the mib variables related to same fuction must be in one snmp set operation, the variables have two type: mandatory and optional. Mandatory variables must be in the one snmp set operation. Optional variables may be in the one snmp set operation with the mandatory variables, but must not be used alone. To modify a service port, there are several cases base on the variable zxAnGponOPVlanPortMode, and the mandatory and optional variables for each case are different. Case 1: to modify a VLAN port when zxAnGponOPVlanPortMode is access(1): - mandatoty: zxAnGponOPVlanPortMode, - optional : zxAnGponOPVlanPortDefaultVid, zxAnGponOPVlanPortDefaultCos, Case 2: to modify a service port when zxAnGponOPVlanPortMode is trunk(2): - mandatoty: zxAnGponOPVlanPortMode, - optional : Case 3: to modify a service port when zxAnGponOPVlanPortMode is hybrid(3): - mandatoty: zxAnGponOPVlanPortMode, - optional : zxAnGponOPVlanPortDefaultVid, zxAnGponOPVlanPortDefaultCos, Case 4: to modify a service port when zxAnGponOPVlanPortMode is transparent(4): - mandatoty: zxAnGponOPVlanPortMode, - optional : Case 5: to modify a service port when zxAnGponOPVlanPortMode is none(5): - mandatoty: zxAnGponOPVlanPortMode, - optional :

The ONU profile port VLAN entry. Supporting Ethernet UNI, WiFi UNI, VEIP, GEM port, multicast GEM port, WAN and xDSL UNI.

The access mode of the port. There are five types: - access: access mode of port access - trunk: trunk mode of port access - hybrid: hybrid mode of port access - transparent: transparent mode of port access - none: delete all the VLAN configuration of the port, restore to ONU's internal policy. Enumeration: 'access': 1, 'none': 5, 'hybrid': 3, 'transparent': 4, 'trunk': 2.

The PVID of the port.

The default priority of the port.

The VLAN sequence of the port.

The port VLAN operation command table. This table is used for ONU profile.

The port VLAN operation command entry. Supporting Ethernet UNI, WiFi UNI, VEIP, GEM port, multicast GEM port, WAN and xDSL UNI.

The command to operate VLAN list of 'zxAnGponOPVlanPortTable'. The multi-variables binding rule should be complied with when a manager configures port VLAN cmd. According to this rule, all the related mib variables must be included in one SNMP set operation. There are two types of variables: mandatory and optional. All of the mandatory variables must be included in one SNMP set operation. Optional variables may be included in one SNMP set operation with the mandatory variables, but must not be used alone. To configure VLAN, the mandatory and optional variables are as follows: mandatoty: zxAnGponOPVlanPortCmd, zxAnGponOPVlanPortVid optional : none There are two groups of operation command, the first group includes addVlan and delVlan, the second group includes addAllVlan and delAllVlan. For an ONU interface, two groups of operation command can't be use at the same time. When zxAnGponOPVlanPortCmd is addAllVlan or delAllVlan and then zxAnGponOPVlanPortVid is invalid. Enumeration: 'addVlan': 1, 'delVlan': 2, 'addAllVlan': 3, 'delAllVlan': 4.

The port VLAN ID. This variable must comply with the multi-variables binding rule described in 'zxAnGponOPVlanPortCmd'.

The ONU profile port VLAN translation table.

The ONU profile port VLAN translation entry. Supporting Ethernet UNI, WiFi UNI, VEIP, GEM port, multicast GEM port, WAN and xDSL UNI.

User VLAN ID for translation.

User priority for translation, the range of priority is from 0 to 8, and '8' indicates no configuration.

Inner VLAN for VLAN translate, '0' indicates no translation. The multi-variables binding rule should be complied with when a manager configures port VLAN translate. According to this rule, all the related mib variables must be included in one SNMP set operation. There are two types of variables: mandatory and optional. All of the mandatory variables must be included in one SNMP set operation. Optional variables may be included in one SNMP set operation with the mandatory variables, but must not be used alone. To configure VLAN translation, the mandatory and optional variables are as follows: mandatoty: zxAnGponOPVlanTransSVid optional : zxAnGponOPVlanTransCVid, zxAnGponOPVlanTransCtagCos, zxAnGponOPVlanTransStagCos

Inner VLAN priority for VLAN translate, '8' indicates no translation. This variable must comply with the multi-variables binding rule described in 'zxAnGponOPVlanTransCVid'.

Outer VLAN for VLAN translate, '0' indicates no SVLAN. This variable must comply with the multi-variables binding rule described in 'zxAnGponOPVlanTransCVid'.

Outer VLAN priority for VLAN translate, '8' indicates copy priority from inner VLAN priority. This variable must comply with the multi-variables binding rule described in 'zxAnGponOPVlanTransCVid'.

The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). In particular, a newly created row cannot be created until the corresponding at least one of 'zxAnGponOPVlanTransCVid zxAnGponOPVlanTransCtagCos zxAnGponOPVlanTransSVid zxAnGponOPVlanTransStagCos' have been set. To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile multicast VLAN table.

The ONU profile multicast VLAN entry.

This attribute represents the VLAN ID (1~4094).

The status of this conceptual row. The state of this conceptual row only support 'not exist' and 'active'. The action of this conceptual row only support 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile IGMP configuration table.

The ONU profile IGMP configuration entry. Supporting Ethernet UNI and VEIP.

This attribute points to an instance of the multicast operations profile.

This attribute specifies the maximum number of dynamic multicast groups that may be replicated to the client port at any one time. The default value 0 specifies that no administrative limit is to be imposed.

This attribute specifies the maximum imputed dynamic bandwidth, in kbps, that may be delivered to the client port at any one time. The default value 0 specifies that no administrative limit is to be imposed.

enabled: attempts to exceed the max multicast bandwidth be counted and denied. disabled: such attempts be counted but honored. Enumeration: 'disabled': 2, 'enabled': 1.

The status of this conceptual row. The state of this conceptual row only support 'not exist' and 'active'. The action of this conceptual row only support 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile traffic scheduler configuration table.

The ONU profile traffic scheduler configuration entry. Supporting Ethernet UNI.

The ONU UNI traffic scheduler profile name. The empty string indicates no profile is bounded.

The ONU profile extended VLAN configuration table.

The ONU profile extended VLAN configuration entry.

This attribute gives the special TPID value for operations on the input (filtering) side of the table. Typical values include 0x8a88 and 0x9100. Default value is 0x8100.

This attribute gives the special TPID value for operations on the output (tagging) side of the table. Typical values include 0x8a88 and 0x9100. Default value is 0x8100.

Regardless of its association, the extended VLAN tagging operation configuration data ME pertains to upstream traffic. This attribute specifies the mode for downstream mapping. 1 The operation performed in the downstream direction is the inverse of that performed in the upstream direction. For one-to-one VLAN mappings, the inverse is trivially defined. Many-to-one mappings are possible, however, and these are treated as follows. If the many-to-one mapping results from multiple operation rules producing the same ANI-side tag configuration, then the first rule in the list defines the inverse operation. If the many-to-one mapping results from don't care fields in the filter being replaced with provisioned fields in the ANI-side tags, then the inverse is defined to set the corresponding fields on the ANI side with their lowest value. 2 No operation is performed in the downstream direction. 3 Filter on VID and p-bit value. On a match, perform the inverse operation on both the VID and p-bit value. If no match is found, forward the frame unmodified. 4 Filter on VID only. On a match, perform the inverse VID operation only; pass the p bits through. If no match is found, forward the frame unmodified. 5 Filter on p-bit only. On a match, perform the inverse p-bit operation only; pass the VID through. If no match is found, forward the frame unmodified. 6 Filter on VID and p-bit value. On a match, perform the inverse operation on both the VID and p-bit value. If no match is found, discard the frame. 7 Filter on VID. On a match, perform the inverse operation on the VID only; pass the p bits through. If no match is found, discard the frame. 8 Filter on p-bit only. On a match, perform the inverse p-bit operation only; pass the VID through. If no match is found, discard the frame. 9 Regardless of the filter rules, discard all downstream traffic. Enumeration: 'inverseVlanAndPriOthersDiscard': 6, 'inverseVlanAndPriOthersForward': 3, 'inverseUpstream': 1, 'inverseVlanOthersForward': 4, 'inversePriOthersDiscard': 8, 'inverseVlanOthersDiscard': 7, 'discard': 9, 'inversePriOthersForward': 5, 'noOperation': 2.

This attribute refers to 'zxAnGponRmDscp2CosPrfName', specifies mapping from DSCP to P-bits. The attribute can be considered a bit string sequence of 64 3-bit groups. The 64 sequence entries represent the possible values of the 6-bit DSCP field. Each 3-bit group specifies the P-bit value to which the associated DSCP value should be mapped.

The status of this conceptual row. The state of this conceptual row only support 'not exist' and 'active'. The action of this conceptual row only support 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile extended VLAN rule configuration table.

The ONU profile extended VLAN rule configuration entry.

This attribute refers to 'zxAnGponRmFiltRuleName' provides a unique profile of filter for this extended VLAN table.

This attribute refers to 'zxAnGponRmTrtRuleName' provides a unique profile of treatment for this extended VLAN table.

The status of this conceptual row. The state of this conceptual row only support 'not exist' and 'active'. The action of this conceptual row only support 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile bridge configuration table.

The ONU profile bridge configuration entry.

This attribute indicates the index of MAC bridge in ONU, from 1 to 65535. The first byte specifies the slot ID associated with this MAC bridge, the second byte specifies the bridge group ID associated with this MAC bridge.

This attribute indicates whether or not a spanning tree algorithm is enabled. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute indicates whether or not the learning function of the bridge is enabled. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute indicates whether or not the bridging between UNI ports is enabled. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute specifies the bridge priority in the range 0..65535. The value of this attribute is copied to the bridge priority attribute of the associated MAC bridge configuration data managed entity.

This attribute indicates the maximum age for an entry in the spanning tree listing. It indicates the maximum age in seconds for received protocol information before it is discarded.

This attribute provides the time interval between hello packets. It is the time interval, in seconds, that a bridge advertises its presence while as a root or attempting to become a root.

This attribute gives the time that the bridge on the Ethernet card in the ONU retains a packet before forwarding it. (It indicates the value in seconds that the bridge uses for Forward Delay when the bridge acts as the root.)

This attribute indicates the treatment of MAC frames with unknown destination addresses. enabled: frames with unknown destination addresses will be discarded. disabled: frames with unknown destination addresses will be forwarded to all allowed ports. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute specifies the maximum number of UNI MAC addresses to be learned by the bridge. The default value 0 specifies that there is no administratively-imposed limit.

This attribute specifies the age of dynamic filtering entries in the bridge database, after which unrefreshed entries are discarded. In accordance with [IEEE 802.1D] clause 7.9.2 and [IEEE 802.1Q] clause 8.8.3, the range is 10..1 000 000 seconds, with a resolution of 1 second and a default of 300 seconds.

The ONU profile WAN IP configuration table.

The ONU profile WAN IP configuration entry.

The ID of WAN IP.

IP address configuration mode. Enumeration: 'dhcp': 2, 'pppoe': 3.

The name of table 'zxAnGponOPVlanPrfTable'.

The ONU IP host ID. The value 0 indicates this attribute is not configured. The following IP host ID format is defined: MSB : Most Significant Byte LSB : Least Significant Byte | MSB | Byte 2 | Byte 1 | LSB | |--------------|-----------------------------------------------| | | |IP-type | reserved | host ID | | (8bits) | (8bits) | (1bit) | (7bits) | (8bits) | |--------------------------------------------------------------| IP-type: the IP type of host ID(1 bit) 0 represents IPv4 1 represents IPv6

A unique ONU identifier string. This string, if set is provided as part of the DHCP request to allow an alternative to MAC Address in retrieving the DHCP parameters of the specified ONU. This attribute is related to 'zxAnGponOPWanIpMode'. and it is valid only when 'zxAnGponOPWanIpMode' is DHCP. Its default value is null bytes.

This attribute is related to 'zxAnGponOPWanIpMode', and it is valid only when 'zxAnGponOPWanIpMode' is PPPoE. Enumeration: 'pap': 3, 'auto': 1, 'chap': 2.

This attribute is related to 'zxAnGponOPWanIpMode', and it is valid only when 'zxAnGponOPWanIpMode' is PPPoE.

This attribute is related to 'zxAnGponOPWanIpMode', and it is valid only when 'zxAnGponOPWanIpMode' is PPPoE.

This attribute indicates whether respond to pings enabled. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute indicates whether respond to trace route enabled. This attribute is only valid for IPv4 and this value is disabled(2) for IPv6. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute indicates whether respond to router solicitation (RS) messages enabled. This attribute is only valid for IPv6 and this value is disabled(2) for IPv4. Enumeration: 'disabled': 2, 'enabled': 1.

It is the manually provisioned on-link prefix used for destination IPv6 addresses of IPv6 host services. The attribute is structured as follows: Prefix length, number of leading bits in the prefix that are valid (1 byte). Prefix (16 bytes). This attribute is only valid for IPv6 and this value is 0x0 for IPv4.

The PPPoE service name.

The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile VoIP configuration table.

The ONU profile VoIP configuration entry.

This attribute indicates the type of VoIP signaling protocol used for ONU. Only one type of protocol is allowed. Valid values are: 0x01 = None 0x02 = SIP 0x03 = H.248 0x04 = MGCP 0x05 = Selected by Non-OMCI. Enumeration: 'none': 1, 'sip': 2, 'h248': 3, 'nonOmci': 5, 'mgcp': 4.

This attribute indicates the ONU configuration method. 0x01 the ONU default - do not configure. 0x02 indicate use of OMCI for VoIP service configuration of the ONU. 0x03 indicate use of configuration file retrieval for VoIP service configuration of the ONU. 0x04 indicate use of TR-69 for VoIP service configuration of the ONU. 0x05 indicate use of IETF sipping config framework for VoIP service configuration of the ONU. Enumeration: 'default': 1, 'tr069': 4, 'configFile': 3, 'omci': 2, 'ietf': 5.

This attribute indicates the ONU domain name that is used to locate ONU by SS when the mode of MG registered to SS is using domain name.

This attribute indicates the ONU equipment name that is used to locate ONU by SS when the mode of MG registered to SS is using equipment name.

This attribute indicates the MID flag. Enumeration: 'equipmentName': 3, 'ipv4': 1, 'domainName': 2.

This attribute indicates the register mode. Enumeration: 'individual': 2, 'wildcard': 1.

This attribute indicates the line name sequence number. The default value is the empty string.

This attribute indicates the VoIP allocate mode. Enumeration: 'multiIp': 3, 'dualIp': 2, 'singleIp': 1.

This attribute indicates the address of the server to contact using the method indicated in the VoIP configuration method used attribute. This attribute is only relevant for non-OMCI configuration methods. If this attribute is set to a null pointer, no address is defined by this attribute. However, the address may be defined by other methods, such as deriving it from the ONU identifier attribute of the IP host configuration data ME and using a well-known URI schema.

This attribute indicates the user validation scheme. Enumeration: 'disabled': 1, 'basic': 3, 'md5': 2.

This attribute indicates the user name for validation.

This attribute indicates the password for validation.

This attribute indicates a string to be displayed to users so they know which user name and password to use. This string should contain at least the name of the host performing the authentication and might additionally indicate the collection of users who might have access. An example might be 'registered_users@gotham. news .com'. The realm is a 'quoted-string' as specified in section 2.2 of the HTTP/1.1 specification.

This attribute indicates an action. It will be set independently to notify ONU to retrieve file again. Enumeration: 'disabled': 2, 'enabled': 1.

The ONU profile VoIP IP configuration table.

The ONU profile VoIP IP configuration entry.

This attribute indicates the index of slot in ONU. If slot ID is zero, it means the ONU is box-type, which can not plug card.

This attribute indicates the whether the separation of media and signaling. If 'media' is configured,The media will use a separation IP address, otherwise media and signaling will share the same IP address. Enumeration: 'media': 2, 'signalAndMedia': 1.

This attribute indicates the IP address configuration mode. Enumeration: 'dhcp': 2, 'static': 1, 'pppoe': 3.

This attribute indicates the VoIP IP profile Name, it refers to 'zxAnGponRmIpPrfName'. If no profile name is indicated, this attribute is set to a empty string.

This attribute indicates the VoIP IP VLAN profile Name, it refers to 'zxAnGponRmVlanPrfName'.

This attribute indicates the ONU VoIP host ID. The value 0 indicates this attribute is not configured. The following VoIP host ID format is defined: MSB : Most Significant Byte LSB : Least Significant Byte | MSB | Byte 2 | Byte 1 | LSB | |--------------|-----------------------------------------------| | | |IP-type | reserved | host ID | | (8bits) | (8bits) | (1bit) | (7bits) | (8bits) | |--------------------------------------------------------------| IP-type: the IP type of host ID(1 bit) 0 represents IPv4 1 represents IPv6

This attribute indicates the ONU identifier string. This attribute is relation to 'zxAnGponOPVoipIpMode'. This attribute is valid only when 'zxAnGponOPVoipIpMode' is DHCP. A unique ONU identifier string. If set to a non-null value, this string is used instead of the MAC address in retrieving DHCP parameters. If the string is shorter than 25 characters, it must be null terminated. Its default value is null bytes.

This attribute indicates the type of IP address denoted in zxAnGponOPVoipIpAddr object.

This attribute indicates the VoIP IP address. This attribute is relation to 'zxAnGponOPVoipIpMode'. This attribute is valid only when 'zxAnGponOPVoipIpMode' is static.

This attribute indicates the VoIP IP address prefix length. This attribute is only valid for IPv4 and this value is 0 for IPv6.

This attribute indicates the VoIP IP PPPoE mode. This attribute is relation to 'zxAnGponOPVoipIpMode'. This attribute is valid only when 'zxAnGponOPVoipIpMode' is PPPoE. Enumeration: 'pap': 3, 'auto': 1, 'chap': 2.

This attribute indicates the VoIP IP PPPoE user name. This attribute is relation to 'zxAnGponOPVoipIpMode'. This attribute is valid only when 'zxAnGponOPVoipIpMode' is PPPoE.

This attribute indicates the VoIP IP PPPoE password. This attribute is relation to 'zxAnGponOPVoipIpMode'. This attribute is valid only when 'zxAnGponOPVoipIpMode' is PPPoE.

This attribute indicates whether respond to pings enabled. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute indicates whether respond to trace route enabled. This attribute is only valid for IPv4 and this value is disabled(2) for IPv6. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute indicates enabling or disabling response to router solicitation (RS) messages function. This attribute is only valid for IPv6 and this value is disabled(2) for IPv4. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute indicates the manually provisioned on-link prefix used for destination IPv6 addresses of IPv6 host services. The attribute is structured as follows: Prefix length, number of leading bits in the prefix that are valid (1 byte)+ prefix (16 bytes). This attribute is only valid for IPv6 and this value is 0x0 for IPv4.

This attribute indicates the PPPoE service name.

The status of this conceptual row. The supported actions of this conceptual row only include: To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To query this object, always return 1.

The ONU profile Ethernet UNI's DHCP controlling configuration table.

The ONU profile Ethernet UNI's DHCP controlling configuration entry.

This attribute indicates the Ethernet UNI how to obtain its IP address (from ONU or network), when ONU enables the DHCP server function. Enumeration: 'fromNetwork': 3, 'forbidden': 4, 'fromOn': 2, 'noSpecify': 1.

This table contains information of ONU IP static routes configuration. This managed entity stores IP static routes.

It is entry in the zxAnGponOPIpStaticRouteTable. The index 'zxAnGponOPName' represents the normal ONU index.

The type of the 'zxAnGponOPIpRouteDest' address, as defined in the InetAddress MIB. Only those address types that may appear in an actual routing table are allowed as values of this object.

The destination IP address of this route. The type of this address is determined by the value of the 'zxAnGponOPIpRouteDestType' object. The values for the index objects 'zxAnGponOPIpRouteDest' and 'zxAnGponOPIpRoutePfxLen' must be consistent. When the value of 'zxAnGponOPIpRouteDest' (excluding the zone index, if one is present) is x, then the bitwise logical-AND of x with the value of the mask formed from the corresponding index object 'zxAnGponOPIpRoutePfxLen' must be equal to x. If not, then the index pair is not consistent and an inconsistentName error must be returned on SET or CREATE requests. This field may be set to the default route address 0.0.0.0 .

Indicates the number of leading one bits that form the mask to be logical-ANDed with the destination address before being compared to the value in the zxAnGponOPIpRouteDest field. The values for the index objects 'zxAnGponOPIpRouteDest' and 'zxAnGponOPIpRoutePfxLen' must be consistent. When the value of 'zxAnGponOPIpRouteDest' (excluding the zone index, if one is present) is x, then the bitwise logical-AND of x with the value of the mask formed from the corresponding index object 'zxAnGponOPIpRoutePfxLen' must be equal to x. If not, then the index pair is not consistent and an inconsistentName error must be returned on SET or CREATE requests.

The type of the 'zxAnGponOPIpRouteNextHopType' address, as defined in the InetAddress MIB. Value should be set to unknown(0) for non-remote routes. Only those address types that may appear in an actual routing table are allowed as values of this object.

On remote routes, the address of the next system route. For non-remote routes, a zero length string. The type of this address is determined by the value of the 'zxAnGponOPIpRouteNextHopType' object. This field is not used when the next hop is reached through an unnumbered link. For IPv4, the value is '255.255.255.255' when not used.

The number of the IP port through which the next hop should be reached. This field is used when the next hop is reached through an unnumbered link and when a static route is set to support a fully meshed network. The value 0xFF indicates not used.

The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). In particular, a newly created row cannot be created until the corresponding attributes from 'zxAnGponOPIpRouteNextHopType' to 'zxAnGponOPIpRouteOutPort' have been set. To delete a row in this table, a manager must set this object to destroy(6).

zxAnGponOPVeipTable table. This managed entity represents the data plane hand-off point in an ONU to a separate (non-OMCI) management domain. The virtual Ethernet interface point is managed by OMCI, and is potentially known to the non-OMCI management domain. One or more Ethernet traffic flows are present at this boundary.

GPON VEIP configuration entry. The index 'zxAnGponOPName' represents the normal ONU index or the virtual ONU index for profile.

This attribute uniquely identifies each instance of this managed entity. To facilitate easy discovery, the ONU should assign IDs in the sequence 1, 2, .... The values 0 and 0xFFFF are reserved and not used now.

This attribute locks and unlocks the functions performed by this managed entity. Enumeration: 'locked': 2, 'unlocked': 1.

This attribute is a character string that provides an optional way to identify the virtual Ethernet interface point to a non-OMCI management domain. The interface may also be identified by its managed entity ID, IANA assigned port and possibly other ways. If the vendor offers no information in this attribute, it should be set to a sequence of null bytes.

This attribute points to an instance of the TCP/UDP config data managed entity, which provides for OMCI management of the non-OMCI management domain's IP connectivity. This attribute specifies whether to assign tcp or udp port for IP connectivity. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute points to an instance of the TCP/UDP config data managed entity, which provides for OMCI management of the non-OMCI management domain's IP connectivity. This attribute specifies the protocol used in IP connectivity. Enumeration: 'udp': 2, 'tcp': 1.

This attribute points to an instance of the TCP/UDP config data managed entity, which provides for OMCI management of the non-OMCI management domain's IP connectivity. This attribute specifies the assigned tcp or udp port for IP connectivity when zxAnGponOPVeipIsTcpOrUdpPortAssigned is true.

This attribute points to an instance of the TCP/UDP config data managed entity, which provides for OMCI management of the non-OMCI management domain's IP connectivity when zxAnGponOPVeipIsTcpOrUdpPortAssigned is true. This attribute specifies the host ID for IP connectivity.

zxAnGponOPTr069AcsTable table. If functions within the ONU are managed by [BBF TR-69], this ME allows OMCI configuration of the ACS URL and related authentication information for an ACS connection initiated by the ONU. TR-69 supports other means to discover its ACS, so not all TR-69-compatible ONUs necessarily support this ME. Further, even if the ONU does support this ME, some operators may choose not to use it.

GPON Tr069 management server configuration entry. The index 'zxAnGponOPName' represents the normal ONU index or the virtual ONU index for profile.

This attribute locks and unlocks the functions performed by this managed entity. When the administrative state is locked, the functions of this ME are disabled. TR-69 connectivity to an ACS may be possible through means that do not depend on this ME. The default value of this attribute is locked. Enumeration: 'locked': 2, 'unlocked': 1.

This attribute points to the large string ME that contains the network address. It may contain a fully qualified domain name, URI or IP address. The URI may also contain a port identifier, eg x.y.z.com:5060. A null pointer indicates that no network address is defined.

This attribute specifies the validation scheme used when the ONU validates a challenge. Validation schemes are defined as follows: 1 Validation disabled. 2 Validate using MD5 digest authentication as defined in [IETF RFC 2069]. 3 Validate using basic authentication as defined in [IETF RFC 2617]. Enumeration: 'disabled': 1, 'basic': 3, 'md5': 2.

This string attribute is the user name. If the string is shorter than 25 bytes, it must be null terminated.

This string attribute is the password. If the string is shorter than 25 bytes, it must be null terminated.

This string attribute specifies the realm used in md5 digest authentication. If the string is shorter than 25 bytes, it must be null terminated.

This attribute is a TCI value for TR-69 management traffic passing through the virtual ethernet interface point. A TCI, comprising user priority, CFI and VID, is represented by 2 bytes. the first 3 bits represent priority. the last 12 bits represent VID. eg: priority(3 bits)| reserved(1 bits) |VID(12bits). The value 0xFFFF specifies that TR-69 management traffic passes through the virtual ethernet interface point with neither a VLAN nor a priority tag.

The ONU profile Ethernet UNI configuration table.

The ONU profile Ethernet UNI configuration entry.

The following coding is used for this attribute: 0x00 = by autosensing, 0x01 to 0xFE (1 to 254) = one of the values from table 3 that is compatible with the type of the LIM. Upon autonomous instantiation, the value 0x00 is used.

For 10/100 Base-Tx Ethernet interfaces, this attribute is used to set the configuration options: auto(1): Auto-sensing; half10(2): 10BaseT (half duplex); full10(3): 10BaseT (full duplex); half100(4): 100BaseT (half duplex); full100(5): 100BaseT (full duplex); full1000(6): Gigabit Ethernet (full duplex); full10000(7): 10G Ethernet (full duplex); Enumeration: 'full100': 5, 'auto': 1, 'full10000': 7, 'half10': 2, 'half100': 4, 'full1000': 6, 'full10': 3.

This attribute is used to set the Ethernet loopback configuration: No loopback (value 0x01), loop3 (value 0x04, Loopback of downstream traffic after PHY transceiver). Enumeration: 'loop3': 4, 'noLoop': 1.

This attribute is used to activate (unlock: value 0x01) and deactivate(lock: value 0x02) the functions performed by instances of this managed entity. Enumeration: 'locked': 2, 'unlocked': 1.

This attribute denotes the maximum allowed frame size to be transmitted across this interface.

This attribute specifies the Ethernet interface wiring: 1 DCE or MDI-X (default). 2 DTE or MDI. 3 Automatic selection Enumeration: 'auto': 3, 'dce': 1, 'dte': 2.

This attribute allows the ONU line card to request that the customer terminal temporarily suspend sending data. Units are in pause quanta(1 pause_quantum equals 512 bits times of the particular implementation).

This attribute specifies whether the Ethernet interface is bridged or derived from an IP router function. 1 Bridged 2 IP router 3 Depends on the parent circuit pack. 3 means that the circuit pack's bridged or IP ind attribute is either 1 or 2. Enumeration: 'ipRouter': 2, 'either': 3, 'bridged': 1.

This attribute allows the activation of alarm reporting control (ARC) for this PPTP or cardholder. The attribute works in concert with the ARC interval attribute. enabled: enables ARC. disabled: disables ARC. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute defines the interval to be used with the ARC function for this PPTP or cardholder. The values 0 through 254 give the duration in minutes for the NALM-QI timer of M.3100. The special value 255 means that the timer never expires. The default value is zero.

This attribute may be used to control filtering of PPPoE packets on this Ethernet port. The value 2 is used to disable filtering. The value 1 is used to enable filtering. When filtering is enabled, all packets other than PPPoE packets will be discarded. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute controls whether power is provided to an external equipment over the Ethernet PPTP. Value 1 enables power over Ethernet port. The default value 2 disables power feed. Enumeration: 'disabled': 2, 'enabled': 1.

This attribute enable or disable the loopback detection. Enumeration: 'disabled': 2, 'enabled': 1.

The compliance statement for entities which implements the ZTE-AN-GPON-ONUPRF-MIB.

A collection of objects for ONU line profile group configuration.

A collection of objects for ONU service profile group configuration.