ZELAX-MIB: View SNMP OID List / Download MIB

setfactory(2) warmReset(3) noReset(1) default the status is 1 Enumeration: 'setfactory': 2, 'warmReset': 3, 'noReset': 1.

The version information of switch hardware

The version information of switch software

If it is the status of stacking Enumeration: 'noStack': 2, 'stack': 1.

The MAC Address is used for switch data transfers

write(1)save the current configuration Enumeration: 'write': 1.

the power supply status is only used for chassis switch

power supply status

Module model No.

if the power supply insert Enumeration: 'sysPowerInstalled': 1, 'sysPowerNotInstalled': 0.

Power Value

Power Type Enumeration: 'poePower': 1, 'systemPower': 0.

Power Status Enumeration: 'na': 2, 'abnormal': 1, 'normal': 0.

machine information,it is only used by chassis.

Switch information

Module Model No.

CPU type

Last 5 second CPU IDLE

Last 30 second CPU IDLE

Last 5 minute CPU IDLE

From running CPU IDLE

memory size

memory usage rent

The flash capacity of this slot.

The Temperature of this slot.80 is 80centigrade

The CPU usage of this slot.

Table of descriptive and status information about switches in this system.

An entry in the table, containing information about a single switch in this system.

This object identifies the slot within the switch for which this entry contains information. While for the chassis device, the value is real switch slot number.

This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.

Type of expansion module in this switch slot. Enumeration: 'type2-NEWMI': 202, 'type1-M8GB': 118, 'type1-L-M4GX24TX': 122, 'type1-16FX': 111, 'type2-M12GB': 165, 'type2-4GX24TX': 185, 'type1-4GX24TX': 121, 'type2-110Gx': 168, 'type1-M4GX24TX': 113, 'type2-M8GB': 182, 'type1-12GX12GTR4': 140, 'type1-M44GT': 131, 'type3-8XFP': 235, 'type1-4XFP': 129, 'type1-MII': 116, 'type2-2XFP8GX16GB': 183, 'type1-E-2XFP24GB12GT': 143, 'type3-MII': 230, 'type1-12GB': 117, 'type2-M1XFP12GX12GT': 192, 'type2-ES2GB': 176, 'type2-M1XFP12GX12GB': 196, 'type2-12GX12GTR4': 204, 'type1-12GT': 102, 'type3-M': 228, 'typeMFC': 0, 'type2-8GX16GB': 184, 'type2-E-2XFP24GB12GT': 207, 'type1-2XFP12GX12GT': 124, 'type2-12GT': 166, 'type2-16FX': 175, 'type2-MI': 179, 'type1GL': 3, 'type1GS': 2, 'type2-12GB': 181, 'type1-1XFP8GX16GB': 123, 'type3-24GT-V': 236, 'type2-24GB12GT': 201, 'type1-4GX32TX': 110, 'typeSFC': 1, 'type10M100MT': 8, 'type1-8GX16GB': 120, 'type1-M1XFP12GX12GB': 132, 'type2-12GX12GB': 197, 'type1-M1XFP12GX12GT': 128, 'type2-1XFP8GX16GB': 187, 'type1-NEWMI': 138, 'type1-12GX12GT': 125, 'type2-2XFP12GX12GB': 198, 'type1-1XFP12GX12GT': 126, 'type1-12GX12GB': 133, 'type2-2XFP12GX12GT': 188, 'type2-4XFP': 193, 'type100M1GT': 4, 'type1-110Gx': 104, 'type3-4XFP': 234, 'type2-24GT': 172, 'type2-1XFP12GX12GT': 190, 'type1-E-24GB12GT': 142, 'type4-2GB': 302, 'type2-24GB': 171, 'type1-210Gx': 103, 'type1-2XFP24GB12GT': 136, 'type2-M44GT': 195, 'type2-12GX12GT': 189, 'type4-4TX': 303, 'type2-2XFP24GB12GT': 200, 'type1-24GT': 108, 'type2-CPU8245': 169, 'type2-4GX32TX': 174, 'type1-BACKPLANE': 106, 'type2-210Gx': 167, 'type1-24GB': 107, 'type2-ES': 178, 'type1-M1XFP12GX12GTR4': 139, 'type2-L-M4GX24TX': 186, 'type2-MII': 180, 'type2-M4GX24TX': 177, 'type3-24GB-V': 237, 'type1-2XFP8GX16GB': 119, 'type2-48GT': 191, 'type3-24GT': 231, 'type2-48GB': 194, 'type3-24GB': 232, 'type4-4FB': 305, 'type1-24GB12GT': 137, 'type1-36TX': 109, 'type1-CPU8245': 105, 'type1-MI': 115, 'type1-ES': 114, 'type3-16BACKPLANE': 240, 'type3-08BACKPLANE': 239, 'type4-4GB': 304, 'type1-M12GB': 101, 'type2-M1XFP12GX12GTR4': 203, 'type1-2XFP12GX12GTR4': 141, 'type1-2XFP12GX12GB': 134, 'type4-4GT': 300, 'type3-ES-FW': 233, 'type4-4FX': 301, 'type1-48GB': 130, 'type2-36TX': 173, 'type2-BACKPLANE': 170, 'type3-MI': 229, 'type1-ES2GB': 112, 'type3-24SFP-PLUS': 238, 'type2-E-24GB12GT': 206, 'type1-48GT': 127, 'type2-2XFP12GX12GTR4': 205.

ftp user name

ftp user password

ftp or tftp server ip address

Source file name or Copy from current system configuration .

Destination file name or Copy to startup configuration.

ascii(0): ASCII file mode; binary(1): Binary file mode. Enumeration: 'binary': 1, 'ascii': 0.

ftp(1): ftp server or client; tftp(2): tftp server or client. Enumeration: 'ftp': 1, 'tftp': 2.

File copy configurate. Enumeration: 'download': 2, 'upload': 1.

The result of file copy:error(0):copy file failure;ok(1):copy file success; uploading(2):in process of upload file;downloading(3):in process of download file; idle(4):be out of copy file. Enumeration: 'ok': 1, 'idle': 4, 'downloading': 3, 'uploading': 2, 'error': 0.

The CPU type of switch

Last 5 second CPU IDLE

Last 30 second CPU IDLE

Last 5 minute CPU IDLE

From running CPU IDLE

memory size

memory usage rent

The flash capacity of switch.

The Temperature of switch.80 is 80centigrade

The CPU usage of switch.

the state of fan.

fan supply status

system fan entry index

Whether the slot fan is installed or not. Enumeration: 'sysFanNotInstalled': 0, 'sysFanInstalled': 1.

Whether the slot fan is normal or abnormal. Enumeration: 'abnormal': 1, 'normal': 0.

Status of Fan. Status: Low(1), Medium(2), High(3), none(0) is readonly Enumeration: 'high': 3, 'none': 0, 'medium': 2, 'low': 1.

Set or get filename of boot img for first time,and the length of filename is between 1 and 128.

Set or get filename of boot img for second time,and the length of filename is between 1 and 128.

Set or get filename of boot startup config ,and the length of filename is between 1 and 128.

this object identifies start up status of switch and AM of chassis.1(idle) means hasn't wrote cfg since boot, 2(success) means wrote cfg successfully; 3(fail) means wrote cfg fail; 4(in-progress) means is writing cfg right now. for chassis:it can only be used by active master Enumeration: 'fail': 3, 'in-progress': 4, 'idle': 1, 'success': 2.

A list of boot information.it is only used by chassis.

Entry for boot information.

slot NO.

Set or get filename of boot img for first time,and the length of filename is between 1 and 128.

Set or get filename of boot img for backup,and the length of filename is between 1 and 128.

Set or get filename of boot startup config ,and the length of filename is between 1 and 128.

If there is a old password, you should enter the old password, then you can set the new password or delete the password. The length of the password is between 3 and 32, enter wrong old password or enter wrong length password, you can not set new password or delete password.

Enter the new password you want to set, and the length of the password is between 3 and 32.

Enter the new password again to confirm the new password, the password entries must match.

If you want to delete the password, enter '1'; if you don't want delete it, you can enter '0' or do nothing. Enumeration: 'enable': 1, 'disable': 0.

If you enter '1', excute the operation you set. Firstly, judge the type of deletePassword, if it is '1', delete the password, and return ok; if the type is '0', then modify the password. At first judge the correctness of oldpassword, then judge the new password equal to confirm password. if they are all right, set the new password. Enumeration: 'enable': 1, 'disable': 0.

Enable or disable the Spanning Tree algorithm in the switch. Enumeration: 'enable': 1, 'disable': 2.

Enable or disable the Spanning Tree algorithm in the switch. Enumeration: 'enable': 1, 'disable': 0.

configure global style of TC FLUSH Enumeration: 'protect': 3, 'enable': 1, 'disable': 2.

This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database.

The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.

The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.

setting global Maxhop of mstp

setting global mode of mstp,stp or rstp Enumeration: 'stp': 0, 'mstp': 3, 'rstp': 2.

setting the name of mst

setting the global revision level of mstp

setting global Forwardtime of mstp

setting global HelloTime of mstp

setting global Maxage of mstp

correlative information list with instance

The index of this table is instance ID

instance ID

the map of vlans to instance.The input format is consonant with cli.

the priority of the router in the special instance.

the region root ID in the special instance.

the path cost from self bridge to Region Root.

the root port ID in the special instance.

interrelated parameter list of instance and port

The index of this table is instance ID and port index

instance ID

port index

port cost of port under the special instance

port priority of port under the special instance

rootguard enable/disable on the current instance Enumeration: 'enable': 1, 'disable': 0.

ID of port which receive a BPDU

the path cost from self bridge to Root bridge

the path cost from self bridge to Region Root

the port state in the instance Enumeration: 'forwarding': 1, 'block': 0, 'learning': 2.

the port role in the instance Enumeration: 'root': 2, 'alternate': 1, 'designated': 3, 'disabled': 6, 'master': 5, 'nonstp': 0, 'backup': 4.

the designated bridge ID

the designated port ID

mstp information list of port

The index of this table is port index

port index

enable/disable mstp on the port. Enumeration: 'enable': 1, 'disable': 0.

the p2p link type of the port Enumeration: 'force-true': 1, 'auto': 2, 'force-false': 0.

trigger/untrigger Enumeration: 'trigger': 1, 'untrigger': 0.

default:the port mode is portfast mode bpdufilter:the port mode is portfast mode with bpdufilter bpduguard:the port mode is portfast mode with bpduguard noportfast:the port mode is not portfast mode Enumeration: 'default': 0, 'noportfast': 3, 'bpduguard': 2, 'bpdufilter': 1.

which mode can be setted up port of message format function Enumeration: 'auto': 2, 'standard': 0, 'privacy': 1.

Whether the port use peer's authentication key Enumeration: 'enable': 1, 'disable': 0.

when topology is changed, how to flush the mac Enumeration: 'useglobal': 0, 'protect': 3, 'enable': 1, 'disable': 2.

The total number of ports in the system.

A list of port entries.

A port entry containing port information, status, and control.

port No.

Name of the port. exp:financial.

This value is denoting the number of swith in which this port resides. For the non-stackable device,the value is always 1. While for the stackable device, the value is real switch stack number.

This value is denoting the number of slot. For the static slot,the value is 1,while for the extended slot the value is real extended slot number.

Type of expansion module in this port. Enumeration: 'typeCombo': 1, 'typeMultiOptFE': 4, 'typeSingleOptGE': 6, 'typeElecFE': 5, 'typePortAGG': 9, 'typeElecGE': 8, 'typeSFP': 0, 'typeSingleOptFE': 3, 'typeMultiOptGE': 7, 'typeFiber': 2, 'typePortUsbGE': 10, 'typeOptXge': 11, 'other': 255.

The flow-control status of the port. Its functionality is exactly same as 'flow control' or 'no flow control' commands in console mode. Enumeration: 'enable': 1, 'disable': 0.

The bandwidth-control status of the port. Its functionality is to stop the bandwidth control. The only way to enable bandwidth control is to set receiveBandwidth or transmitBandwith. Enumeration: 'both': 2, 'ingress': 0, 'egress': 1, 'none': 3.

The max bandwidth of the port. Enumeration: 'default': 0, 'bw1000M': 2, 'bw10000M': 3, 'bw100M': 1.

The recevice bandwidth of the port. Its unit is kbs. The command 'bandwidth control 50 both' in console mode equals setting both receiveBandwidth and transmitBandwidth to 50 kbs. Set 0 is no bandwidth.

The transmit bandwidth of the port. Its unit is kbs. Set 0 is no bandwidth.

Close or open to specify the port. Enumeration: 'noshutdown': 1, 'shutDown': 0.

Open or close to specify the wreath of the port back to test the function. Enumeration: 'noloopback': 0, 'loopback': 1.

The speed and duplex status of the port. Enumeration: 'neg-10-100-full': 20, 'full-1000-M': 9, 'neg-10-100-1000-half': 23, 'fx-100-no-phy': 15, 'full100': 4, 'full-1000-s': 10, 'neg-10-100-1000-full': 22, 'half10': 1, 'neg-10-100-half': 21, 'fx-100-phy': 14, 'auto': 0, 'half100': 3, 'full1000': 6, 'half-1000-s': 8, 'full10': 2, 'neg-10-auto': 16, 'neg-10-100-auto': 19, 'half1000': 5, 'neg-10-full': 17, 'half-1000-M': 7, 'neg-10-half': 18, 'fx-100': 13.

port mode: 1 is access,2 is trunk,3 is hybrid Enumeration: 'access': 1, 'hybrid': 3, 'trunk': 2.

port of native vlan No.

Indicates the port type of the configuration of the switch. Enumeration: 'hundredBaseFX': 3, 'thousandBaseGBIC': 7, 'thousandBaseLX': 5, 'hundredBaseTX': 2, 'tenG': 12, 'thousandBaseCX': 11, 'thousandBaseT': 6, 'hundredBaseFxScSingleMode': 9, 'thousandBaseSfp': 8, 'hundredBaseFxScMultiMode': 10, 'other': 1, 'thousandBaseSX': 4.

This object indicates the VCT action of the port,only the value 1 is permitted when SET this entry though you can GET 1(processing) and 0(succeed); The specified port will be shutdown when one sets 1 to this entry,and then it will return to no shutdown after operate the virtual-cable-test. You can get the status of VCT from the entry vctLastStatus.

Indicates the last VCT status of the port.

trunk port allowed vlan list string

hybrid port tagged allowed vlan list string

hybrid port untagged allowed vlan list string

The percentage of the port's bandwidth usage

storm-contol table

storm-control entry

port index

broadcast(broadcast rate suppression),multicast(multicast rate suppression), unicast(unicast rate suppression),dlf(Destination Lookup Failure rate suppression), brmc(broadcast and multicast rate suppression),brmcdlf(Broadcast, multicast and DLF rate suppression) Enumeration: 'broadcast': 0, 'all': 6, 'dlf': 3, 'unicast': 2, 'brmcdlf': 5, 'multicast': 1, 'brmc': 4.

the suppress rate.the value range at <1-1488095> or <1-1000000> on different devices.

Setting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry Enumeration: 'active': 1, 'destroy': 0.

This value is the state recovery time.When this time comes, port back to the normal state.But when the value is 0, does not restore state.

This detection time interval is present when the loop exists, in seconds, the range of 5 to 300. The default value is 5.

This detection time interval is present when the loop does not exist, in seconds, the range from 1 to 30,The default value is 3.

A table containing current configuration information for the function of loopback detection control.

An entry in the loopback detection control table.

An unique value for each port.

Indicates the control type of the configuration of the loopback detection. The default value is 0. When the value is set to 0,the loopback detection control function will be disabled. Enumeration: 'nocontrol': 0, 'shutdown': 1, 'block': 2.

Setting the loopback detection function for the specified vlan of the port.

An entry in the loopbackDetecSpecVlanTable.

An unique value for each port.

The value is a vlan list that you will set.Please pay attention to the list of writing,eg:1;3;5-20 .

When lpbackDetecVlanListSetFlag is 1,open the specified VLAN loopback detection function.When lpbackDetecVlanListSetFlag is 0,close the specified VLAN loopback detection function. Enumeration: 'close': 0, 'open': 1.

Show the config and state of loopback detection for the specified port.

An entry in the loopbackDetecShowTable.

An unique value for each port.

The value display the configuration and state of loopback detection for the specified port.

The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.

Web server on-off. Enumeration: 'enable': 1, 'disable': 0.

A table of iPAddrEntry.

A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is composed of the ifIndex assigned to the corresponding interface.

The VLAN interface being used by this table entry. Only the VLAN interfaces which have an IP configured will appear in the table.

The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the IPAddrIPAddress or IPAddrSubnetMask is 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).

The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the IPAddrIPAddress or IPAddrSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).

Whether this is a primary interface. Enumeration: 'primary': 0, 'secondary': 1.

Now state. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

A table of interfaceEntry.

A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is composed of the ifIndex assigned to the corresponding interface.

The Type of interface. Now support(1)vintf and (2)loopback. Enumeration: 'vintf': 1, 'tunnel': 3, 'loopback': 2.

The Number of interface. exp:intfacetype(1),interfaceID(2) means interface vlan 2. if intfacetype(2) interfaceID(4) means interface loopback4. if intfacetype(3) interfaceID(5) means interface Tunnel5.

The Index of interface.

Now state. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

A table containing current configuration information for each VLAN currently configured into the device by (local or network) management.

Static information for a VLAN configured into the device by (local or network) management.

This value is vlan's ID.

which may be used to identify the VLAN.

The sum of vlan's ports.

This object indicates the status of this entry. Enumeration: 'active': 1, 'destroy': 2.

A table containing current configuration information for Multicast VLAN .

Static information for Multicast VLAN configured into the device by (local or network) management.

This value is mvlan's ID.

the status of mVLAN:enable(1) to active a mvlanID;disable(0) is to destroy a mvlanID. Enumeration: 'enable': 1, 'disable': 0.

configure vlans association with multicast Vlan,such as'3-4'or '2,5,6',set or unset by Configuring mvlanAssoVlanStatus; geting vlans which associating with multicast Vlan .

the status of mvlanAssoVlan:enable(1) to enable multicast Vlan association with Vlan; disable(0) is to disable multicast Vlan association with Vlan. Enumeration: 'enable': 1, 'disable': 0.

configure mode: when no configration,Default: 0. Enumeration: 'default': 0, 'compatible': 2, 'dynamic': 1.

A table containing current configuration information for each Multicast VLAN .

Static information for Multicast VLAN configured into the device by (local or network) management.

This value is mvlan's ID.

Mvlan's port index.

tagId of portIndex association with multicast Vlan,Default:0.if port needn't Tagid, set portIndex association with mvlanVId only.

the status of mvlanPortStatus:enable(1) to enable port association with multicast Vlan; disable(0) is to disable port association with multicast Vlan. Enumeration: 'enable': 1, 'disable': 0.

the number of the stacked units.

Table of descriptive and status information about jumbly stacking in this system.

An entry in the table, containing information about stacking switch in this system.

This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.

The text string denoting the version of the hardware.

The text string denoting the version of the software.

the Mac address of the machine.

Type of this switch.

The table of port security

An entry in the port security table.

A unique value for each port

enable or disable mac bind on this port Enumeration: 'enable': 1, 'disable': 0.

bind Security mac address on this port

delete Security mac address on this port

lock or unlock this port Enumeration: 'lock': 1, 'unlock': 0.

Maximum secure addrs on this port

convert dynamic mac to security mac

lock timer on this port

Table of descriptive and status information about security port

An entry in the security mac port table.

A unique value for each port

Mac adress bind on this port

vlan id of this port(pvid)

Enable or disable the IgmpSnooping algorithm in the switch. Enumeration: 'enable': 1, 'disable': 0.

IopgmpSnoing configuration in vlan.

IgmpSnooping confition in vlan.

This value is vlan's ID.

Enable or disable the IgmpSnooping in the switch.Default:0 Enumeration: 'enable': 1, 'disable': 0.

Enable or disable the immediate leave config.Default:0 Enumeration: 'immediate-leave': 1, 'no-immediate-leave': 0.

Enable or disable the l2-general-querier config.Default:0 Enumeration: 'no-l2-general-querier': 0, 'l2-general-querier': 1.

set the maximum IGMP group the port can join

set the maximum source number

Get static mrouter port of vlan. ethernet: Name of Ethernet port ifname: Name of interface port-channel: Port aggregation.

Configure this survive time of mrouter port.Default: 255s

Configure this query interval. Default: 125s

Configure the maximum query response period. Default: 10s

Configure the query robustness.Default: 2

Configure the suppression query time.Default: 255s

IgmpSnoing bind configuration.

IgmpSnooping bind configuration.

This value is vlan's ID.

This value is group's ip address.

Port's bitmap.

port of qinq tunnel function list

configure of dot1qTunnel

port index

Enable or disable the dot1q-tunnel in this port. Enumeration: 'enable': 1, 'disable': 0.

Protocol type of trunk port(TPID)(exp:33024(0x8100)/37120(0x9100)/37376(0x9200)).

VLAN translation basic config.

VLAN translation

Index of Port.

if the port can be done translation function Enumeration: 'enable': 1, 'disable': 0.

when VLAN-translation missed, drop packet mode Enumeration: 'both': 3, 'noBoth': 6, 'noOut': 5, 'in': 1, 'noIn': 4, 'out': 2.

port VLAN-translation of translation relation list

port VLAN translation of translation relation,index is port index and translation sort

port index

translation type. in:input translation; out:output translation. Enumeration: 'in': 1, 'out': 2.

vlantranslation pre-vid

the new vid

accession/delete VLAN-translation relation Enumeration: 'active': 1, 'destroy': 2.

firewall on-off Enumeration: 'enable': 1, 'disable': 0.

timeRange Map Table

timeRange Map Entry

TimeRange Map index,the range of it is 1-(2^32-1).

TimeRange Map name

TimeRange Map status Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

timeRange Table

timeRange Entry

TimeRange index,the allowed range is 1 to 1000.

TimeRange sub index,the allowed range is 1 to 1000.

TimeRange type Enumeration: 'periodic': 2, 'absolute': 1.

configurate the start week,for example: f8 means monday+tuesday+wednesday+thurday+friday, the lowest bit is not used,so fe is the biggest. Bits: 'monday': 0, 'tuesday': 1, 'friday': 4, 'wednesday': 2, 'thursday': 3, 'sunday': 6, 'saturday': 5.

configurate the start Date,for example YYYY.MM.DD .

configurate the start clock,for example HH:MM:SS.

configurate the end week,for example: f8 means monday+tuesday+wednesday+thurday+friday, the lowest bit is not used,so fe is the biggest. Bits: 'monday': 0, 'tuesday': 1, 'friday': 4, 'wednesday': 2, 'thursday': 3, 'sunday': 6, 'saturday': 5.

configurate the end date,for example YYYY.MM.DD.

configurate the end clock,for example HH:MM:SS.

status of timeRangeMapTable Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

this table is used for building a num-acl list.

numAclGroup Table's Entry

the index of number acl,ip standard <1-99>,ip extern <100-299>,mac standard <700-799>, mac extern <1100-1199>,ipv6 standard <500-599> ipv6 extern <600-699>.

value 0 means Acl rule's priority is automatically configured, value 1 means Acl rule's priority is manually configured, but now it's not supported. Enumeration: 'configPriority': 1, 'autoPriority': 0.

the Number of one acl's rule.

the status of number acl. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

this table is used for building a name-acl list and mapping a string of named acl to a value of number, when you want to config name-acl list,you must map at here.

nameAclGroup Table's Entry

the index of name acl,the range starts at 20000.

the name of name-acl.

the type of name acl. Enumeration: 'ipv6Extern': 7, 'ipExtern': 1, 'macStandard': 2, 'macIpExtern': 4, 'macIpStandard': 5, 'ipStandard': 0, 'ipv6Standard': 6, 'macExtern': 3.

value 0 means Acl rule's priority is automatically configured, value 1 means Acl rule's priority is manually configured, but now it's not supported. Enumeration: 'configPriority': 1, 'autoPriority': 0.

the Number of one acl's rule.

the status of nameAclGroupTable. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

config ip Standard Acl

ip standard Table's Entry

The index of ip-standard-acl group.

The index of ip-standard-acl rule.

The priority of standard ip acl's rule,it is not supported now.

The action of acl rule. Enumeration: 'deny': 0, 'permit': 1.

Source IP-address of basic acl rule.

Source IP-address wild of basic acl rule.

status of the ipStandardAclTable. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

ip extern Acl Table

ip extern Table's Entry

The index of ip-Extern-acl group .

The index of ip-Extern-acl rule .

The priority of extern ip acl's rule,it is not supported now.

The action of acl rule. Enumeration: 'deny': 0, 'permit': 1.

The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value value of 0 matches every IP packet. For example : 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50 is ESP, 51 is AH, 88 is EIGRP, 89 is OSPF, 94 is KA9Q/NOS compatible IP over IP, 103 is PIMv2, 108 is PCP.

Source IP-address of advanced acl rule,for example 10.1.1.0 .

Source IP-address wild of advanced acl rule,for example 0.0.0.255 .

Destination IP-address of advanced acl rule,for example 10.1.1.0 .

Destination IP-address wild of advanced acl rule,for example 0.0.0.255 .

The Time-range of advanced acl rule.

Indicates how a packet's source TCP/UDP port number is to be compared. If the numIpExternProtocol object in the same row does not indicate TCP or UDP, this object has to be 'noOperator(0)' and cannot be changed while this row is active, i.e., the value of numIpExternStatus in the same row has the value 'active(1)'. 'noOperator(0)', which is the default value, means that no comparison is to be made with the source TCP/UDP port number. eq(1) means equal, This operators are using the ipExternSrcPort1 object as an operand which is the only one needed. range(3) means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is ipExternSrcPort1 object, and the other operand is the ending port number of the range which the ipExternSrcPort2 object is in. Now support(3)eq,(5)range. Enumeration: 'range': 2, 'eq': 1, 'noOperator': 0.

The source port number of the TCP or UDP protocol. If the numIpExternSrcOP object in the same row is range(5), this object will be the starting port number of the port range. This object cannot be configured if numIpExternStatus in the same row is active(1) or numIpExternSrcOP in the same row is noOperator(0).

The source port number of the TCP or UDP protocol. If the numIpExternSrcOP object in the same row is range(5), this object will be the ending port number of the port range. This object cannot be configured if numIpExternStatus in the same row is active(1) or numIpExternSrcOP in the same row is not range(5).

Indicates how a packet's Destination TCP/UDP port number is to be compared. If the numIpExternProtocol object in the same row does not indicate TCP or UDP, this object has to be 'noOperator(0)' and cannot be changed while this row is active, i.e., the value of numIpExternStatus in the same row has the value 'active(1)'. 'noOperator(0)', which is the default value, means that no comparison is to be made with the source TCP/UDP port number. eq(1)means equal, This operators are using the numIpExternDestPort object as an operand which is the only one needed. range(5) means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is numIpExternSrcPort object, and the other operand is the ending port number of the range which the numIpExternDestPortRange object is in. Now support(3)eq,(5)range. Enumeration: 'range': 2, 'eq': 1, 'noOperator': 0.

The source port number of the TCP or UDP protocol. If the numIpExternDestOP object in the same row is range(5), this object will be the starting port number of the port range. This object cannot be configured if numIpExternStatus in the same row is active(1) or numIpExternDestOP in the same row is noOperator(0).

The source port number of the TCP or UDP protocol. If the numIpExternDestOP object in the same row is range(5), this object will be the ending port number of the port range. This object cannot be configured if numIpExternStatus in the same row is active(1) or numIpExternDestOP in the same row is not range(5).

now state of the access-list. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

mac Standard Acl Table

mac standard Table's Entry

The index of mac-standard-acl group .

The index of mac-standard-acl rule .

The priority of standard mac acl's rule,it is not supported now.

The action of acl rule. Enumeration: 'deny': 0, 'permit': 1.

Source Mac-address of basic acl rule,for example : ff-ff-ff-ff-ff-00.

Source Mac-address's anti-mask of basic acl rule,for example : ff-ff-ff-ff-00-00.

status of the access-list. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

mac extern Acl Table

mac extern Table's Entry

The index of Mac-Extern-acl group.

The index of Mac-Extern-acl rule.

The priority of extern mac acl's rule,it is not supported now.

The action of acl rule. Enumeration: 'deny': 0, 'permit': 1.

Source Mac-address of advanced acl rule,for example : ff-ff-ff-ff-ff-00.

Source Mac-address's anti-mask of advanced acl rule,for example : ff-ff-ff-ff-00-00.

Destination Mac-address of advanced acl rule,for example : ff-ff-ff-ff-ff-00.

Destination Mac-address's anti-mask of advanced acl rule,for example : ff-ff-ff-ff-00-00.

Indicates the message type of packets.none(0),untagged-eth2(1), untagged-802.3(2),tagged-eth2(3),tagged-802.3(4)

Value of the ethertype

Anti-mask of the ethertype

value of the cos

Anti-mask of the cos

vlan id

Anti-mask of the vlan id

now state of the access-list. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

ipv6 Standard Acl Table

ipv6 standard Table's Entry

The index of ipv6-standard-acl group.

The index of ipv6-standard-acl rule.

The priority of standard ipv6 acl's rule,it is not supported now.

The action of acl rule. Enumeration: 'deny': 0, 'permit': 1.

Source IPV6-address of basic acl rule,for example : 3ffe:506::100.

Source IPV6-address prefix length of basic acl rule.

now state of the access-list. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

ipv6 extern Acl Table

ipv6 extern Table's Entry

The index of ipv6-Extern-acl group .

The index of ipv6-Extern-acl rule .

The priority of extern ipv6 acl's rule,it is not supported now.

The action of acl rule. Enumeration: 'deny': 0, 'permit': 1.

The protocol number field in the IP header used to indicate the higher layer protocol as specified . For example : 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50 is ESP, 51 is AH, 88 is EIGRP, 89 is OSPF, 94 is KA9Q/NOS compatible IP over IP, 103 is PIMv2, 108 is PCP

Source IPV6-address of advanced acl rule,for example : 3ffe:506::100.

Source IP-address prefix length of advanced acl rule.

Destination IPV6-address of advanced acl rule,for example : 3ffe:506::100.

Destination IPV6-address prefix length of advanced acl rule.

The Time-range of advanced acl rule.

Indicates how a packet's source TCP/UDP port number is to be compared. If the ipv6ExternProtocal object in the same row does not indicate TCP or UDP, this object has to be 'noOperator(0)' and cannot be changed while this row is active, i.e., the value of ipv6ExternStatus in the same row has the value 'active(1)'. 'noOperator(0)', which is the default value, means that no comparison is to be made with the source TCP/UDP port number. eq(3) means equal,range(5) means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is ipv6ExternSrcPort1 object, and the other operand is the ending port number of the range which the ipv6ExternSrcPort2 object is in. Enumeration: 'range': 5, 'eq': 3, 'noOperator': 0.

The source port number of the TCP or UDP protocol. If the ipv6ExternSrcOp object in the same row is range(5), this object will be the starting port number of the port range. This object cannot be configured if ipv6ExternStatus in the same row is active(1) or ipv6ExternSrcOp in the same row is noOperator(0).

The source port number of the TCP or UDP protocol. If the ipv6ExternSrcOp object in the same row is range(5), this object will be the ending port number of the port range. This object cannot be configured if ipv6ExternStatus in the same row is active(1) or ipv6ExternSrcOp in the same row is not range(5).

Indicates how a packet's Destination TCP/UDP port number is to be compared. If the ipv6ExternProtocal object in the same row does not indicate TCP or UDP, this object has to be 'noOperator(0)' and cannot be changed while this row is active, i.e., the value of ipv6ExternStatus in the same row has the value 'active(1)'. 'noOperator(0)', which is the default value, means that no comparison is to be made with the source TCP/UDP port number. eq(3) means equal,range(5) means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is ipv6ExternDstPort1 object, and the other operand is the ending port number of the range which the ipv6ExternDstPort2 object is in. Enumeration: 'range': 5, 'eq': 3, 'noOperator': 0.

The Destination port number of the TCP or UDP protocol. If the ipv6ExternDstOp object in the same row is range(5), this object will be the starting port number of the port range. This object cannot be configured if ipv6ExternStatus in the same row is active(1) or ipv6ExternDstOp in the same row is noOperator(0).

The Destination port number of the TCP or UDP protocol. If the ipv6ExternDstOp object in the same row is range(5), this object will be the ending port number of the port range. This object cannot be configured if ipv6ExternStatus in the same row is active(1) or ipv6ExternDstOp in the same row is not range(5).

status of ipv6ExternAclTable. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

mac-ip extern Acl Table

mac-ip extern Table's Entry

The index of macIp-Extern-acl group .

The index of macIp-Extern-acl rule .

The priority of extern macIp acl's rule,it is not supported now.

The action of acl rule. Enumeration: 'deny': 0, 'permit': 1.

The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value value of 0 matches every IP packet. For example : 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50 is ESP, 51 is AH, 88 is EIGRP, 89 is OSPF, 94 is KA9Q/NOS compatible IP over IP, 103 is PIMv2, 108 is PCP.

Source Mac-address of advanced acl rule,for example : ff-ff-ff-ff-ff-00.

Source Mac-address's anti-mask of advanced acl rule,for example : ff-ff-ff-ff-00-00.

Destination Mac-address of advanced acl rule,for example : ff-ff-ff-ff-ff-00.

Destination Mac-address's anti-mask of advanced acl rule,for example : ff-ff-ff-ff-00-00.

Source IP-address of advanced acl rule,for example 10.1.1.0 .

Source IP-address wild of advanced acl rule,for example 0.0.0.255 .

Destination IP-address of advanced acl rule,for example 10.1.1.0 .

Destination IP-address wild of advanced acl rule,for example 0.0.0.255 .

The Time-range of advanced acl rule.

Indicates how a packet's source TCP/UDP port number is to be compared. If the macIpExternProtocal object in the same row does not indicate TCP or UDP, this object has to be 'noOperator(0)' and cannot be changed while this row is active, i.e., the value of macIpExternStatus in the same row has the value 'active(1)'. 'noOperator(0)', which is the default value, means that no comparison is to be made with the source TCP/UDP port number. eq(3) means equal, This operators are using the macIpExternSrcPort1 object as an operand which is the only one needed. range(5) means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is macIpExternSrcPort1 object, and the other operand is the ending port number of the range which the macIpExternSrcPort2 object is in. Now support(3)eq,(5)range. Enumeration: 'range': 5, 'eq': 3, 'noOperator': 0.

The source port number of the TCP or UDP protocol. If the macIpExternSrcOP object in the same row is range(5), this object will be the starting port number of the port range. This object cannot be configured if macIpExternStatus in the same row is active(1) or numIpExternSrcOP in the same row is noOperator(0).

The source port number of the TCP or UDP protocol. If the macIpExternSrcOP object in the same row is range(5), this object will be the ending port number of the port range. This object cannot be configured if numIpExternStatus in the same row is active(1) or macIpExternSrcOP in the same row is not range(5).

Indicates how a packet's Destination TCP/UDP port number is to be compared. If the macIpExternProtocol object in the same row does not indicate TCP or UDP, this object has to be 'noOperator(0)' and cannot be changed while this row is active, i.e., the value of macIpExternStatus in the same row has the value 'active(1)'. 'noOperator(0)', which is the default value, means that no comparison is to be made with the source TCP/UDP port number. eq(3)means equal, This operators are using the macIpExternDstPort object as an operand which is the only one needed. range(5) means that it compares the port value between two numbers, so this operator needs 2 operands. One operand is the starting port number of the range which is macIpExternSrcPort1 object, and the other operand is the ending port number of the range which the macIpExternDstPort2 object is in. Now support(3)eq,(5)range. Enumeration: 'range': 2, 'eq': 1, 'noOperator': 0.

The source port number of the TCP or UDP protocol. If the macIpExternDstOP object in the same row is range(5), this object will be the starting port number of the port range. This object cannot be configured if macIpExternStatus in the same row is active(1) or macIpExternDstOP in the same row is noOperator(0).

The source port number of the TCP or UDP protocol. If the macIpExternDstOP object in the same row is range(5), this object will be the ending port number of the port range. This object cannot be configured if numIpExternStatus in the same row is active(1) or macIpExternDstOP in the same row is not range(5).

The precedence of macIp-Extern-acl .

The tos of macIp-Extern-acl .

state of the access-list. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

bind Acl in port or vlan.

Entry for aclActiveTable

point out the type of position of the bind-acl. Enumeration: 'vlan': 1, 'port': 0.

The value of port id or vlan id .

the type of acl. Enumeration: 'ip': 1, 'mac': 3, 'macIp': 5, 'ipv6': 2.

the direction of a binding acl. Enumeration: 'out': 0, 'in': 1.

the value of acl index,you have configured in aclNumAccessGroupTable or aclNameAccessGroupTable.

support traffic statistic or not. Enumeration: 'enable': 1, 'disable': 0.

access or delete the bind-acl. Enumeration: 'enable': 1, 'disable': 0.

clear traffic-statistic in port or vlan.

entry for aclStatisticClearTable

point out the type of position of the bind-acl. Enumeration: 'vlan': 1, 'port': 0.

the direction of a binding acl. Enumeration: 'out': 0, 'in': 1.

The value of port id or vlan id .

clear the bind-acl's traffic-statistic. Enumeration: 'enable': 1, 'disable': 0.

The status of Secure Shell Server, set this value to 1 to enable SSH server, set this value to 0 to disable the SSH server. Enumeration: 'enable': 1, 'disable': 0.

The version of the SSH Server.

The time interval that the router waits for the SSH client to respond. The range is 10-600.

The number of attempts after which the interface is reset. The range is 1-10.

The table for Secure Shell Connection.

The conceptual row for sshConnInfoTable.

Enumeration: 'cryptograph': 7, 'noCryptograph': 0.

Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

The table for Secure Shell Connection.

The conceptual row for sshConnInfoTable.

The connection ID of the Secure Shell Connection.

The SSH version.

The SSH connection State. negotiationStart(1) mean the SSH is in its negotiation start state, authenticationStart(2) mean the SSH is in authentication start state, sessionStart(3) mean the SSH is in session start State. Enumeration: 'negotiationStart': 1, 'authenticationStart': 2, 'sessionStart': 3.

User Name.

IP address of TACACS server.

IP address of TACACS server.

IP address of TACACS server.

Port of TACACS server.

Enumeration: 'noPrimary': 0, 'primary': 1.

Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

Key for TACACS. Input space(' ') to clear this key

The time before retransmit of the TACACS server.

The time before retransmit of the TACACS server.

Key for TACACS. Input space(' ') to clear this key

Global Enable or disable the Access Management. Enumeration: 'enable': 1, 'disable': 2.

Access Management information list of port.

port index

Enable or disable the Access Management on the port. Enumeration: 'enable': 1, 'disable': 2.

Access Management forwarding type. Enumeration: 'ip-pool': 1, 'mac-ip-pool': 2.

IP address of Access Management.

Mac address of Access Management.

Seriate IP address number.

Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

Enable or disable Aaa function. Enumeration: 'enable': 1, 'disable': 0.

Enable or disable Aaa Accounting function. Enumeration: 'enable': 1, 'disable': 0.

Enable or disable Aaa Accounting update function. Enumeration: 'enable': 1, 'disable': 0.

Enable or disable Aaa Accounting DHCP-Binding function. Enumeration: 'enable': 1, 'disable': 0.

Configuration items and information list of RADIUS authentication server host.

Index of RADIUS authentication server.

IP address of RADIUS authentication server.

Port of RADIUS authentication server.

Key for RADIUS authentication server. Input space(' ') to clear this key

Configuration of primary or not primary Enumeration: 'noPrimary': 0, 'primary': 1.

Configuration access mode of none, dot1x or telnet Enumeration: 'none': 0, 'telnet': 2, 'dot1x': 1.

Setting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry. Enumeration: 'active': 1, 'destroy': 2.

Configuration items and information list of RADIUS accounting server host.

Index of RADIUS accounting server.

IP address of RADIUS accounting server.

Port of RADIUS accounting server.

Key for RADIUS accounting server. Input space(' ') to clear this key

Configuration of primary or not primary Enumeration: 'noPrimary': 0, 'primary': 1.

Setting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry. Enumeration: 'active': 1, 'destroy': 2.

The time before retransmit of the RADIUS server.

Retransmit time before giving up the current RADIUS server.

The time before retry of the down-server.

Key for RADIUS. Input space(' ') to clear this key

Accounting update interval.

Radius server nas IPv4. Input 0.0.0.0 to delete nas ipv4 address

Radius server nas IPv6. Input 0 to delete nas IPv6 address

qos golbal switch.disable express close,enable is open. Enumeration: 'enable': 1, 'disable': 0.

qos port configration.

qos port list of concrete definition.index is port index

port Index

the relation between qosPortType and CLI: 1 mls qos cos { }; 0 mls qos trust {cos [pass-through-cos] [pass-through-dscp]|dscp [pass-through-cos] [pass-through-dscp]| ip-precedence [pass-through-cos] [pass-through-dscp] |port priority [pass-through-cos] [pass-through-dscp]} ; 2 mls qos dscp-mutation ; 3 priority-queue out. According to the relation,when configurate qos with snmp,first set the qosPortType to the correct value to select CLI, then set next CLI parameter.Fox example,set qos default cos is 5, first set qosPortType=1 ,then set qosPortCos to 5, finally setting qosPortStatus to 1, trigger snmp-cache works. Enumeration: 'trust': 0, 'dscpMutation': 2, 'cos': 1, 'priorityQueueOut': 3.

port default cos value

Configure port trust. priority(0),mls qos trust port priority ; priAndPassThroughDscp(1),opposite cli is mls qos trust port priority pass-through-dscp; priAndPassThroughCos(2),opposite cli is mls qos trust port priority pass-through-cos; priAndPassThroughCosAndPassThroughDscp(3),opposite cli is mls qos trust port priority pass-through-cos pass-through-dscp; cos(4),mls qos trust cos; cosAndPassThroughDscp(5),opposite cli is mls qos trust cos pass-through-dscp; cosAndPassThroughCos(6),opposite cli is mls qos trust cos pass-through-cos; cosAndPassThroughCosAndPassThroughDscp(7),opposite cli is mls qos trust cos pass-through-cos pass-through-dscp; dscp(8),mls qos trust dscp; dscpAndPassThroughCos(9),opposite cli is mls qos trust dscp pass-through-cos; dscpAndPassThroughDscp(10),opposite cli is mls qos trust dscp pass-through-dscp; dscpAndPassThroughDscpAndPassThroughCos(11),opposite cli is mls qos trust dscp pass-through-dscp pass-through-cos; ipPrecedence(12), mls qos trust ip-precedence; ipPreAndPassThroughCos(13),opposite cli is mls qos trust ip-precedence pass-through-cos; ipPreAndPassThroughDSCP(14),opposite cli is mls qos trust ip-precedence pass-through-dscp; ipPreAndPassThroughDSCPAndPassThroughCos(15),opposite cli is mls qos trust ip-precedence pass-through-dscp pass-through-cos; mplsEXP(16),mls qos mpls trust exp. Enumeration: 'ipPreAndPassThroughDSCP': 14, 'priority': 0, 'cos': 4, 'cosAndPassThroughCos': 6, 'cosAndPassThroughDscp': 5, 'dscpAndPassThroughCos': 9, 'ipPreAndPassThroughCos': 13, 'dscp': 8, 'ipPrecedence': 12, 'cosAndPassThroughCosAndPassThroughDscp': 7, 'priAndPassThroughCosAndPassThroughDscp': 3, 'dscpAndPassThroughDscp': 10, 'dscpAndPassThroughDscpAndPassThroughCos': 11, 'priAndPassThroughCos': 2, 'mplsEXP': 16, 'priAndPassThroughDscp': 1, 'ipPreAndPassThroughDSCPAndPassThroughCos': 15.

The corresponding CLI:mls qos trust port priority .

configure port of dscp-mutation,opposite cli 'mls qos dscp-mutation '

priorityQueue configure queue out method to strict priority-queue method; wrrQueue restores the default wrr queue out method. Enumeration: 'priorityQueue': 0, 'wrrQueue': 1.

Setting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry. Enumeration: 'active': 1, 'destroy': 2.

classmap configure list

about classmap list of concrete definition,index is classmapname.

classmap name

0 class-map ,index is classmapname; 1 match access-group ,need qosClassMapAccessGroup cooperation; 2 match ip dscp qosClassMapDscp ; 3 match ip precedence qosClassMapIpPre; 4 match vlan qosClassMapVlan; 5 match ipv6 dscp qosClassMapV6Dscp; 7 match ipv6 flowlabel qosClassMapV6Flow; 8 match ipv6 access-group qosClassMapV6AccGroup 9 match cos qosClassCos 10 match mpls-experimental topmost qosClassMapEXPtopmost Enumeration: 'v6dscp': 5, 'cos': 9, 'ippre': 3, 'v6Flow': 7, 'vlan': 4, 'accessGroup': 1, 'dscp': 2, 'configurClassMap': 0, 'exptopmost': 10, 'v6AccessGroup': 8.

Match specify access-group (name or number). This object be configured only if qosClassMapType in the same row is accessGroup(1).

Match specify Dscp. This object be configured only if qosClassMapType in the same row is dscp(2).

Match specify ipv6 Dscp. This object be configured only if qosClassMapType in the same row is v6dscp(5).

Match specify Ip Precedence. This object be configured only if qosClassMapType in the same row is ippre(3).

Match specify Ipv6 Access-Group. This object be configured only if qosClassMapType in the same row is v6AccessGroup(8).

Match specify Ipv6 Flowlabel. This object be configured only if qosClassMapType in the same row is v6Flow(6).

Match specify Vlan list . At most 8 vlan id. This object be configured only if qosClassMapType in the same row is vlan(4).

Match specify Cos . This object be configured only if qosClassMapType in the same row is cos(9).

Match specify MPLS EXP. This object be configured only if qosClassMapType in the same row is EXPtopmost(10).

Setting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry. Enumeration: 'active': 1, 'destroy': 2.

qos policy list

qos policy list of definition,index is qos policy and classmap of name

QoS Policy name

Specify the classmap name.After a policy map is created, it can be associated to a class. So, if you want the class map to match the policy map,please setting the qosPolicyType to 1,and then setting the qosPolicyStatus to 1 .

the relation between qosPolicyType and CLI: 0 policy-map ; 1 class ; 2 police [exceed-action {drop | policed-dscp-transmit}]; 3 police aggregate ; Enumeration: 'aggregatePolicer': 3, 'matchclassmap': 1, 'policymap': 0, 'sp': 2.

Rate Bandwidth of one policymap. This object be configured only if qosPolicyType in the same row is sp(2).

Normal burst kbytes.

Maximum burst kbytes.

Peak information rate.

conform-action transmit means send packets without any change when specified speed is not exceeded; conform-action drop means drop packets when specified speed is not exceeded; conform-action set-dscp-transmit specifies to mark down packet DSCP value according to policed-dscp mapping when specified speed is not exceeded; conform-action set-prec-transmit specifies to mark down packet TOS value according to policed-dscp mapping when specified speed is not exceeded. Enumeration: 'transmit': 0, 'set-dscp-transmit': 2, 'drop': 1, 'set-prec-transmit': 3.

If conform-action is set-dscp-transmit(2),the value is between 0-63; else if conform-action is set-prec-transmit(2),the value is between 0-7.

exceed-action transmit means send packets without any change when specified speed is exceeded; exceed-action drop means drop packets when specified speed is exceeded; exceed-action policed-dscp-transmit specifies to mark down packet DSCP value according to policed-dscp mapping when specified speed is exceeded. Enumeration: 'transmit': 0, 'drop': 1, 'policeDscpTransmit': 2.

violate-action transmit means send packets without any change when specified speed is violate; violate-action drop means drop packets when specified speed is violate; violate-action policed-dscp-transmit specifies to mark down packet DSCP value according to policed-dscp mapping when specified speed is violate. Enumeration: 'transmit': 0, 'drop': 1, 'policeDscpTransmit': 2.

aggregate-policer-name. This object be configured only if qosPolicyType in the same row is aggregatePolicer(3).

Setting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry. Enumeration: 'active': 1, 'destroy': 2.

qos of AggPolicer list,use it can configure one item AggPolicer,Attention : the get/get next operation can only get snmp cache content, please refer to qosshow node for the running configuraton

index is AggPolicer name.

QoS qosAggPolicer name

Rate Bandwidth of After the classification.

Normal burst kbytes.

Maximum burst kbytes.

Peak information rate.

conform-action transmit means send packets without any change when specified speed is not exceeded; conform-action drop means drop packets when specified speed is not exceeded; conform-action set-dscp-transmit specifies to mark down packet DSCP value according to policed-dscp mapping when specified speed is not exceeded; conform-action set-prec-transmit specifies to mark down packet TOS value according to policed-dscp mapping when specified speed is not exceeded. Enumeration: 'transmit': 0, 'set-dscp-transmit': 2, 'drop': 1, 'set-prec-transmit': 3.

If conform-action is set-dscp-transmit(2),the value is between 0-63; else if conform-action is set-prec-transmit(2),the value is between 0-7.

exceed-action transmit means send packets without any change when specified speed is exceeded; exceed-action drop means drop packets when specified speed is exceeded; exceed-action policed-dscp-transmit specifies to mark down packet DSCP value according to policed-dscp mapping when specified speed is exceeded. Enumeration: 'transmit': 0, 'drop': 1, 'policeDscpTransmit': 2.

violate-action transmit means send packets without any change when specified speed is violate; violate-action drop means drop packets when specified speed is violate; violate-action policed-dscp-transmit specifies to mark down packet DSCP value according to policed-dscp mapping when specified speed is violate. Enumeration: 'transmit': 0, 'drop': 1, 'policeDscpTransmit': 2.

Setting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry. Enumeration: 'active': 1, 'destroy': 2.

remark new dscp or ip precedence for classified flow

qosSetTable list of acce index policyname and classmap name.

QoS Policy name

QoS class map name

qosSetType range:1,2,3,4,5,6,7,8,9 1 dscp Set IP DSCP (DiffServ CodePoints); 2 precedence Set IP precedence; 3 nexthop Set IP nexthop; 4 dscp Set IPv6 DSCP (DiffServ CodePoints); 6 flowlabel Set IPv6 flowlabel; 7 v6nextHop Set IPv6 nexthop; 8 cos Set CoS ; 9 expimposition Set mpls-experimental-imposition Enumeration: 'v6Dscp': 4, 'v6nextHop': 7, 'cos': 8, 'nextHop': 3, 'precedence': 2, 'expimposition': 9, 'dscp': 1, 'v6FlowLabel': 6.

remark dscp for the classified flow

remark ip precedence for classified flow

set nexthop for classified flow

remark ipv6 dscp for classified flow

remark ipv6 flow lable for classified flow

set IPv6 nexthop for classified flow

remark cos for classified flow

remark MPLS EXP value for classified flow

Setting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry. Enumeration: 'active': 1, 'destroy': 2.

Apply a policy map to the specified port.

the index of this entry is port-index and policy-map

QoS Port Index

QoS Policy name

input(1),bind the policy-map to ingress port; output(2),bind the policy-map to egress port; noinput(3),unbind the policy-map to ingress port; nooutput(4), unbind the policy-map to egress port Enumeration: 'noinput': 3, 'input': 1, 'nooutput': 4, 'output': 2.

set golbal qos WRR weight

set port qos WRR weight,index is port index.

QoS Port Index

WRR weight,range is 0~15.

WRR weight,range is 0~15.

WRR weight,range is 0~15.

WRR weight,range is 0~15.

WRR weight,range is 0~15.

WRR weight,range is 0~15.

WRR weight,range is 0~15.

WRR weight,range is 0~15.

Setting it to active(1) creates an entry.Setting it to destroy(2) destroys an entry. Enumeration: 'active': 1, 'destroy': 2.

qosMapType range is 1~5.1 mls qos map cos-dscp ; 2 mls qos map dscp-cos to ; 3 mls qos map dscp-mutation to ; 4 mls qos map ip-prec-dscp ; 5 mls qos map policed-dscp to ; 6 mls qos map exp-dscp ; 7 mls qos map dscp-exp to When you want to configure the Map of DSCP to COS,please configure the qosMapType==2 firstly, input the dscp(1~8) optionally, then configure the qosMapCos , valid/invalid the qosMapStatus finally. Enumeration: 'cosDscp': 1, 'dscpexp': 7, 'policedDscp': 5, 'dscpMutation': 3, 'expdscp': 6, 'ipPrecDscp': 4, 'dscpCos': 2.

DSCP-CoS map,DSCP range is 0~63

DSCP-CoS map,DSCP range is 0~63

DSCP-CoS map,DSCP range is 0~63

DSCP-CoS map,DSCP range is 0~63

DSCP-CoS map,DSCP range is 0~63

DSCP-CoS map,DSCP range is 0~63

DSCP-CoS map,DSCP range is 0~63

DSCP-CoS map,DSCP range is 0~63

the cos which DSCP map to

the EXP value which DSCP map to

the dscp after mark down

normal-burst:markdown map used by the exceed-action;max-burst:markdown map used by the violate-action. Enumeration: 'normal-burst': 0, 'max-burst': 1.

map name

egress DSCP,only one,eight ingress DSCP value map to one egress value

Setting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry. Enumeration: 'active': 1, 'destroy': 2.

show class map table

show class map entry

classmap name

one item classmap match rule

show policy list

policy map entry

policy name

the match classmap and all defined other rules

display aggregatepolicer list

aggregatepolicer entry,index is showqosaggregatepolicername

aggregatepolicer name

aggregatepolicer parameter

show port qos configuration

showmlsqosinterfaceTable,index is port-index

port index

qos port configuration

cos-dscp map

COS-wrr-queue map

DSCP-COS map

IP precedence to DSCP map

DSCP mark down map

Normal Burst Policed-dscp map

EXP to DSCP map

DSCP to EXP map

ingress DSCP to egress DSCP map

index is dscpmutationname

dscpmutationname.

DSCP-DSCP map

this table is used for building a policy and mapping the named policy to number, if you want to configure a policy,you must map at here.

entry for policy map group.

the range is 0-(2^64 - 1).

the policy name

indicate that whether the policy used on extand field processor. Enumeration: 'enable': 1, 'disable': 0.

the status of qos3PolicyMapGroupTable Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

this table is used for configuring the filter rule of qos

entry for class map.

the name of class

the clss type that you want to matching. Enumeration: 'cos': 0, 'exp': 5, 'vlan': 6, 'dscp': 1, 'ipPrecedence': 2, 'ipv6Dscp': 3, 'ipv6Flowlabel': 4, 'aclIndex': 7.

the value of you choosed type at last node,the limits: cos <0-7> dscp <0-63> ipPrecedence<0-7> ipv6Dscp<0-63> vlan <1-4094> ipv6Flowlabel<0-1048575> exp is not support now.except aclindex,you can config 8 parameters at most,for example,if you choose the type of cos,you can config 0,1,2,3,4,5,6,7 or 0,1 at here.

display how many times the class used.

the status of qos3ClassMapTable,destroy(2) will destroy the whole class-map,remove(3) just clear the value of qos3ClassMapValue. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0, 'remove': 3.

this table is used for configuring aggregate policy.

entry for aggregate policy.

the name of aggregate policy.

CIR(Committed Information Rate) Kbits per second <1-10000000>

CBS(Committed Burst Size) Kbytes <1-1000000>

PBS(Peak Burst Size) Kbytes <1-1000000>

PIR(Peak Information Rate) Kbits per second <1-10000000>

Action when rate is not exceeded,for example: if you want to config cos(2) and intp(5),you must set 24 (0010 0100). Bits: 'cos': 2, 'drop': 1, 'dscp': 3, 'ipPrecedence': 4, 'intp': 5, 'transmit': 0, 'dp': 6.

Set COS

Change dscp

Change precedence

Set Internal priority

Set Drop priority

Action when rate is exceeded,for example: if you want to config cos(2) and intp(5),you must set 24 (0010 0100). Bits: 'policiedIntpTransmit': 7, 'cos': 2, 'drop': 1, 'dscp': 3, 'ipPrecedence': 4, 'intp': 5, 'transmit': 0, 'dp': 6.

Set COS

Change dscp

Change precedence

Set Internal priority

Set Drop priority

Action when rate is violated,for example: if you want to config cos(2) and intp(5),you must set 24 (0010 0100). Bits: 'policiedIntpTransmit': 7, 'cos': 2, 'drop': 1, 'dscp': 3, 'ipPrecedence': 4, 'intp': 5, 'transmit': 0, 'dp': 6.

Set COS

Change dscp

Change precedence

Set Internal priority

Set Drop priority

the status of qos3AggregatePolicyTable Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

this table is used for configuring policy

entry for policy.

the index of policy that you configured at qos3PolicyMapGroupTable

Specify the classmap name.After a policy map is created, it can be associated to a class

Specify the position of classmap name

pidAction means simple policy.colorAction and aggregateAction is Mutually exclusive,for example,if you want the pidAction and colorAction become effective,you must set the value c0. Bits: 'colorAction': 1, 'pidAction': 0, 'aggregateAction': 2.

CIR(Committed Information Rate) Kbits per second <1-10000000>

CBS(Committed Burst Size) Kbytes <1-1000000>

PBS(Peak Burst Size) Kbytes <1-1000000>

PIR(Peak Information Rate) Kbits per second <1-10000000>

Action when rate is not exceeded,for example: if you want to config cos(2) and intp(5),you must set 24 (0010 0100). Bits: 'cos': 2, 'drop': 1, 'dscp': 3, 'ipPrecedence': 4, 'intp': 5, 'transmit': 0, 'dp': 6.

Set COS

Change dscp

Change precedence

Set Internal priority

Set Drop priority

Action when rate is exceeded,for example: if you want to config cos(2) and intp(5),you must set 24 (0010 0100). Bits: 'policiedIntpTransmit': 7, 'cos': 2, 'drop': 1, 'dscp': 3, 'ipPrecedence': 4, 'intp': 5, 'transmit': 0, 'dp': 6.

Set COS

Change dscp

Change precedence

Set Internal priority

Set Drop priority

Action when rate is violated,for example: if you want to config cos(2) and intp(5),you must set 24 (0010 0100). Bits: 'policiedIntpTransmit': 7, 'cos': 2, 'drop': 1, 'dscp': 3, 'ipPrecedence': 4, 'intp': 5, 'transmit': 0, 'dp': 6.

Set COS

Change dscp

Change precedence

Set Internal priority

Set Drop priority

the name of aggregate policy

enable the Counter statistics or not. Enumeration: 'enable': 1, 'disable': 0.

simple policy action,for example: if you want to config cos(0) and setSTpid(10),you must set 8020 (1000 0000 0010 0000). some network Management Software offer selections that is not correct,in RFC3417,When encoding an object whose syntax is described using the BITS construct, the value is encoded as an OCTET STRING, in which all the named bits in (the definition of) the bitstring, commencing with the first bit and proceeding to the last bit,are placed in bits 8 (high order bit) to 1 (low order bit) of the first octet, followed by bits 8 to 1 of each subsequent octet in turn, followed by as many bits as are needed of the final subsequent octet, commencing with bit 8. Remaining bits,if any, of the final octet are set to zero on generation and ignored on receipt. Bits: 'ipNextHop': 3, 'cos': 0, 'setTunnelId': 13, 'setSTpid': 10, 'ipv6NextHop': 5, 'drop': 15, 'delCvid': 12, 'addSvid': 11, 'dscp': 1, 'ipPrecedence': 2, 'intp': 6, 'exp': 4, 'transmit': 14, 'setSvid': 9, 'dp': 7, 'setCvid': 8.

set cos

change dscp

change precedence

Set Internal priority

Set Drop priority

set vlan id of inner VLAN tag.

set vlan id of outer VLAN tag.

Set S-tpid Enumeration: 'value0x8100': 1, 'value0x9100': 3, 'value0x88a8': 2.

add vlan id of outer VLAN tag

delete vlan id of inner VLAN tag. Enumeration: 'enable': 1, 'disable': 0.

whether add Default routing of ip type. Enumeration: 'enable': 1, 'disable': 0.

set the vrf of ip type

set Nexthop IP address.

set exp.

whether add Default routing of ipv6 type Enumeration: 'enable': 1, 'disable': 0.

set the vrf of ipv6 type.

set Nexthop IPv6 address

the status of qos3PolicyTable. destroy(2) will put off the class-map,removeColorAct(3) will clear the color-act, removeAggregateAct(4) will clear the aggregate-act,removePidAct(5) will clear the value while you set int pidAction. Enumeration: 'removeAggregateAct': 4, 'removeColorAct': 3, 'createAndGo': 0, 'removePidAct': 5, 'active': 1, 'destroy': 2.

qos port configration.

entry for port configuration of qos about trust,cos value,queue drop-algorithm and queue algorithm.

port index.

set default cos of the port.

set port trust. cosEnable,dscpEnable and expEnable can be set at the same time;cosDisable,dscpDisable and expDisbable can be set at the same time; cosEnable,dscpEnable and expEnable can not be set at the same time with dscpDisable,cosDisable and expDisbable. Bits: 'expEnable': 2, 'dscpEnable': 1, 'cosDisable': 3, 'expDisbable': 5, 'dscpDisable': 4, 'cosEnable': 0.

set the drop Algorithm of port's queue. Enumeration: 'wred': 1, 'tail': 0.

effected the weight Algorithm of port's queue. Enumeration: 'sp': 0, 'wrr': 1, 'wdrr': 2.

forbid changing the value of cos. Enumeration: 'enable': 1, 'disable': 0.

forbid changing the value of dscp. Enumeration: 'enable': 1, 'disable': 0.

this table is used for configuring port's weight

entry for queue weight configuration.

port index.

choose the algorithm weight that you want to set. Enumeration: 'wrr': 0, 'wdrr': 1.

wrr default value is 1,wdrr default value is 10.

wrr default value is 2,wdrr default value is 20

wrr default value is 3,wdrr default value is 40

wrr default value is 4,wdrr default value is 80

wrr default value is 5,wdrr default value is 160

wrr default value is 6,wdrr default value is 320

wrr default value is 7,wdrr default value is 640

wrr default value is 8,wdrr default value is 1280

the status of qos3QueueWeightTable. Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

this table is used for setting bindwidth of port.

entry for Queue BindWidth configuration.

port index.

queue id

the Smallest bindwidth.

the Largest bindwidth.

the status of qos3QueueBindWidthTable Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

this table is used for configuring the drop Algorithm of queue

entry for queue wred configuration.

port index.

queue id.

drop Priority.

the smallist queue length when the queue start Discard packet.

the Largest queue length when the queue start Discard packet

the max Discard Probability

the status of qos3QueueWredEntry Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

this table is used for setting map between priorities(eg:cos,intp).

entry for mls qos map configuration.

the type of map,if the range of intp value beyonds 0-7,please config it in qos3MapIntpExtendTable. Enumeration: 'intpToCos': 4, 'cosToCosRed': 9, 'cosToIntp': 0, 'cosToDscpGreen': 10, 'cosToCosGreen': 7, 'expToDp': 3, 'cosToCosYellow': 8, 'intpToExp': 6, 'cosToDscpYellow': 11, 'intpToDscp': 5, 'cosToDp': 1, 'expToIntp': 2, 'cosToDscpRed': 12.

according to maptype,map a to b for the first value.

according to maptype,map a to b for the second value.

according to maptype,map a to b for the third value.

according to maptype,map a to b for the fourth value.

according to maptype,map a to b for the fifth value.

according to maptype,map a to b for the sixth value.

according to maptype,map a to b for the seventh value.

according to maptype,map a to b for the eighth value.

the status of qos3MapTable Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

this table is used for mapping between dscp and other priorities.

entry for mls qos dscp map configuration.

the type of map Enumeration: 'dscpToCosGreen': 6, 'dscpToDscpRed': 5, 'dscpToIntp': 0, 'dscpToDscpYellow': 4, 'dscpToCosRed': 8, 'dscpToCosYellow': 7, 'dscpToDscpGreen': 3, 'dscpToDscp': 2, 'dscpToDp': 1.

the index of dscp

the map value

the status of qos3MapDscpTable Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

bind the policy to port or vlan.

entry for qos bind.

bind the policy to port or vlan Enumeration: 'vlan': 1, 'port': 0.

port index or vlan id

the direction of binding Enumeration: 'ext': 2, 'out': 0, 'in': 1.

the policy name

the status of qos3ServicePolicyTable Enumeration: 'active': 1, 'destroy': 2, 'createAndGo': 0.

this table is used for clearing counter statistics

entry for clear statistics of vlan or port.

bind to port or vlan Enumeration: 'vlan': 1, 'port': 0.

port index or vlan id

the direction that you want to clear Enumeration: 'out': 0, 'in': 1.

the status of qos3StatisticClearTable Enumeration: 'enable': 1, 'disable': 0.

this table is used for enabling QOS ETS and MC_UC mode.

entry for enabling ETS and MC_UC.

port index