Wellfleet-Series7-MIB: View SNMP OID List / Download MIB

The BackPlane identification number. Enumeration: 'aceln': 2, 'fns': 4, 'freln': 16640, 'acecn': 3, 'acefn': 1, 'in': 5, 'frecn': 16896.

The revision level of the BackPlane. High byte is in upper 2 bytes.

The serial number of the BackPlane.

Status of BCN Hot-Swappable Power Supply 1 Enumeration: 'fail': 2, 'notpresent': 3, 'ok': 1.

Status of BCN Hot-Swappable Power Supply 2 Enumeration: 'fail': 2, 'notpresent': 3, 'ok': 1.

Status of BCN Hot-Swappable Power Supply 3 Enumeration: 'fail': 2, 'notpresent': 3, 'ok': 1.

Status of BCN Hot-Swappable Power Supply 4 Enumeration: 'fail': 2, 'notpresent': 3, 'ok': 1.

Status of BCN Fan Tray Enumeration: 'fail': 2, 'notpresent': 3, 'ok': 1.

Status of BCN Fan Tray Enumeration: 'caution': 2, 'notpresent': 3, 'ok': 1.

Hardware Table - indexed by slot number

Hardware specific information about a slot.

A unique value for each slot. Its value ranges between 1 and 14. There are products in this family that contain 1, 5, and 14 slots.

The module identification number. Port Configurations HWStat Name Enet Sync Async Token Framer Fiber ------ ------------ ------ ---- ----- ----- ------ ----- 1 ENET-1 2 0 0 0 0 0 8 ENET-2 2 0 0 0 0 0 16 SYNC-1 0 4 1 0 0 0 17 SYNC-1 [1] 0 4 1 0 0 0 24 T1-1 0 2 1 0 2 0 32 DSE-1 1 2 1 0 0 0 33 DSE-1 [1] 1 2 1 0 0 0 40 DST-4/16 0 2 1 1 0 0 41 SST-4/16 [1] 0 1 1 1 0 0 42 DST-4 0 2 1 1 0 0 43 SST-4 [1] 0 1 1 1 0 0 44 SST-4/16 0 1 1 1 0 0 45 STOK-4/16 [3] 0 0 0 1 0 0 46 SST-4 0 1 1 1 0 0 47 STOK-4 [3] 0 0 0 1 0 0 48 FLOPPY 0 0 0 0 0 0 56 T1-2 0 2 1 0 2 0 57 T1-2 0 2 1 0 2 0 58 ST1 0 1 1 0 1 0 60 T1-56K 0 1 1 0 1 0 61 E1 [3] 0 2 0 0 2 0 62 ST1-56K 0 1 1 0 1 0 63 SE1 [3] 0 1 0 0 1 0 64 T1-2n 0 2 1 0 2 0 65 ST1n 0 1 1 0 1 0 66 T1-56Kn 0 1 1 0 1 0 67 ST1-56Kn 0 1 1 0 1 0 68 E1n [3] 0 2 0 0 2 0 69 SE1n [3] 0 1 0 0 1 0 80 SYNC-2 0 4 1 0 0 0 81 SYNC-2 [1] 0 4 1 0 0 0 88 CMC-FDDI [6] 0 0 0 0 0 1 89 IPHASE-FDDI [6] 0 0 0 0 0 1 104 DT 0 0 0 2 0 0 112 DSDE-1 2 2 1 0 0 0 113 DSDE-1 [1] 2 2 1 0 0 0 114 ENET 2 0 0 0 0 0 116 DSE-2 1 2 1 0 0 0 117 DSE-2 [1] 1 2 1 0 0 0 118 SSE 1 1 1 0 0 0 119 SSE [1] 1 1 1 0 0 0 120 DSDE10BT 2 2 0 0 0 0 132 ENET-3 [2] 2 0 0 0 0 0 156 DSDE-2 [2] 2 2 1 0 0 0 160 QE/NF 4 0 0 0 0 0 161 DE/NF [5] 2 0 0 0 0 0 162 QE/NF 4 0 0 0 0 0 164 QE/F [4] 4 0 0 0 0 0 165 DE/F [4,5] 2 0 0 0 0 0 168 MCT1 0 2 Munich 0 0 2 0 176 DTOK 0 0 0 2 0 0 168 MCE1 0 2 Munich 0 0 2 0 192 WF_FDDI_2M 0 0 0 0 0 1 193 WF_FDDI_1M 0 0 0 0 0 1 194 WF_FDDI_2S 0 0 0 0 0 1 195 WF_FDDI_1S 0 0 0 0 0 1 196 WF_FDDI_2MF 0 0 0 0 0 1 197 WF_FDDI_1MF 0 0 0 0 0 1 198 WF_FDDI_2SF 0 0 0 0 0 1 199 WF_FDDI_1SF 0 0 0 0 0 1 208 FNSDSE [7] 1 2 0 0 0 0 216 FNSDSDT [7] 0 2 0 2 0 0 217 FNSDST [7] 0 2 0 1 0 0 224 DHSSI 0 2 hssi 0 0 0 0 225 SHSSI 0 1 hssi 0 0 0 0 8448 SRML 0 0 0 0 0 0 NOTES: [1] Indicates Module has COM Port 1 configured for ASYNC. The AM8530's port B is configured for COM1. [2] This Module contains the DEFA - Hardware Filtering. CAMS must be programmed (can contain 2 - 6 CAMS onboard). [3] The AM8530 has been removed (depopulated) from this module. Programming this device should not be performed. [4] Contains Dual Defa hardware. (Can be depopulated) [5] Depop'd two ports of hardware to make Dual Ethernet module. [6] These are FDDI modules. The ID cannot be read from the Link module I/O space. [7] These are FNS Platform Integrated 'Modules' - Cannot be detached or be used by any other platform. Enumeration: 'enet': 114, 'wffddi2sf': 198, 'qef': 164, 'stok4': 47, 't156kn': 66, 'dst4': 42, 'dse2': 116, 'sync': 80, 't156k': 60, 'cmcfddi': 88, 'shssi': 225, 'dhssi': 224, 't12n': 64, 'dtok': 176, 'dse1a': 33, 'sync2a': 81, 'dse1': 32, 'dsde1': 112, 'dst416': 40, 'enet2': 8, 'enet1': 1, 'wffddi2s': 194, 'wffddi1sf': 199, 'dse2a': 117, 'srml': 8448, 'dt': 104, 'dsde2': 156, 'st1n': 65, 'stok416': 45, 'st156k': 62, 't11': 24, 't12': 56, 'sst416a': 41, 'wffddi2mf': 196, 'ssea': 119, 't12a': 57, 'mct1': 168, 'oldqenf': 160, 'st1': 58, 'se1': 63, 'floppy': 48, 'wffddi1mf': 197, 'mce1': 184, 'wffddi2m': 192, 'sse': 118, 'sync1a': 17, 'sst4a': 43, 'e1': 61, 'sst416': 44, 'fnsdsdt': 216, 'wffddi1m': 193, 'fnsdse': 208, 'se1n': 69, 'wffddi1s': 195, 'sst4': 46, 'sync1': 16, 'qenf': 162, 'fnsdst': 217, 'dsde1a': 113, 'e1n': 68, 'iphfddi': 89, 'dsde10bt': 120, 'enet3': 132, 'denf': 161, 'def': 165, 'st156kn': 67.

The revision level of the module. High byte is in upper 2 bytes.

The serial number of the module.

The mother board identification number. Enumeration: 'ace32': 4, 'fns': 5, 'srmf': 8704, 'fre': 256, 'ace25': 3, 'ace12': 2, 'in': 6, 'sysctrl': 1.

The revision level of the mother board. High byte is in upper 2 bytes.

The serial number of the mother board.

The daughter board identification number. Enumeration: 'ace68020mhz25': 3, 'fre68040mhz25': 4352, 'ace68030mhz32': 4, 'sysctrl': 1, 'ace68020mhz12': 2, 'fre68040mhz33': 4608.

The revision level of the daughter board. High byte is in upper 2 bytes.

The serial number of the daughter board.

The baby board identification number.

The revision level of the baby board. High byte is in upper 2 bytes.

The serial number of the baby board.

The revision level of the Diagnostic PROM. Major revision level is in the upper 2 bytes, minor revision level in the lower 2 bytes.

The creation date of the Diagnostic PROM

The origin of the Diagnostic PROM contents

The revision level of the BOOT PROM. Major revision level is in the upper 2 bytes, minor revision level in the lower 2 bytes.

The creation date of the Boot PROM

The origin of the Boot PROM contents

The revision level of the BOOT PROM. Major revision level is in the upper 2 bytes, minor revision level in the lower 2 bytes.

The creation date of the Spare PROM

The origin of the Spare PROM contents

Flag indicating presence of File System on this slot. Enumeration: 'filesys': 1, 'nofilesys': 2.

State of this record Enumeration: 'init': 1.

Instance of this record

actual module ID and Option

actual module Revision

module PROM

module ID register

module LED register

module MISR register

module SNPROM

SNPROM MAC address connector 1

SNPROM MAC address connector 2

SNPROM MAC address connector 3

SNPROM MAC address connector 4

LANCE line 1

LANCE line 2

MK5025 line 1

MK5025 line 2

MK5025 line 3

MK5025 line 4

SYNC interface control register

SYNC baudrate register

8530 DUART

CAM assembly register

DEFA A chip

CAM A lock

CAM A unlock

DEFA B chip

CAM B lock

CAM B unlock

ILACC line 1

ILACC line 2

ILACC line 3

ILACC line 4

TOKEN ring chip line 1

TOKEN ring chip line 2

TOKEN control register

TOKEN source route accelerator

T1 mux RAM active

T1 mux RAM inactive

T1 interface control register

T1 framer line 1

T1 framer line 2

FDDI FSI line 1

FDDI MAC line 1

FDDI ELM A line 1

FDDI ELM B line 1

FDDI Module control register line 1

HSSI FSI line 1

HSSI FSI line 2

HSSI UGA-330-2 line 1

HSSI UGA-330-2 line 2

HSSI Control Register address

HSSI Last value written to the HICR

HSSI Line Status Register address

HSSI Last value read from HLSR

Bit mask for loading the IP routing suite (RIP, EGP, OSPF) on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the DECNet router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the AppleTalk router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the XNS router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the IPX router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the ISO router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the X.25 DTE protocol on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the X.25 DCE protocol on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the VINES router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the Ethernet II driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the Quad Ethernet driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the FDDI driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the Dual Sync - Dual Enet driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the Dual Sync - Dual Enet II driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the Quad Sync driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the Dual Token driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the DST driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the T1 II driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the E1 II driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the HSSI driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the FNSDSE driver on slot 2 (FNES Only). The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the FNSDSDT driver on slot 2 (FNTS Only). The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the LANCE chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the ILACC chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the FDDI System Interface (FSI) chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth. This attribute shall be used to configure the FSI chip driver on the appropriate slots for FDDI only (see wfHSSIFSILoad for other usage).

Bit mask for loading the TMS380 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the MK5025 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the DS2180 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the DS2181 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.

Bit mask for loading the AM99C10 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth. The AM99C10 chip is Content Addressable Memory (CAM) and the driver to control it is represented by this attribute. The generic name of this attribute shall be the Hardware Filter Driver which will also provide control of the Dual Ethernet Filter Accelerator (DEFA) chip.

Bit mask for loading the AMZ8530 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

Bit mask for loading the HSSI FSI chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.

A textual description of the entity including full name and version of the system's hardware type, OS, and networking SW

Provides an unambiguous means for determining the MIB type (old product vs. harpoon MIB).

Time in seconds/100 since the last cold start

Contact person for this node and where/how to contact them

Node's fully qualified domain name or administratively assigned name

Physical Location of this Node

A sum of numbers indicating the set of services the entity offers. For each layer L, add 2**(L - 1). Example: 78 = Layers 2,3,4, and 7.

The positive or negative offset from Greenwich Mean Time (GMT). This effectively describes the time zone.

The version of the private management information base currently being used by the system software. Format is: xV.RR

Baud rate configured on the Technician Interface console

Number of data bits configured on the Technician Interface console

Type of parity configured on the Technician Interface console Enumeration: 'even': 3, 'none': 1, 'odd': 2.

Number of stop bits configured on the Technician Interface console Enumeration: 's15bit': 2, 's2bit': 3, 's1bit': 1.

Enable the Technician Interface console to run over a modem Enumeration: 'disabled': 2, 'enabled': 1.

Number of lines which can be displayed in one screen on the Technician Interface console

Enable the 'more' feature on the Technician Interface console Enumeration: 'disabled': 2, 'enabled': 1.

Character string which will be used as the system prompt on the Technician Interface console

IF MODEM_ENABLED then time out in minutes to HUP when at the login prompt Enumeration: 'default': 1, 'minimum': 1, 'maximum': 99.

Timout on Password entry Enumeration: 'default': 1, 'minimum': 1, 'maximum': 99.

IF MODEM_ENABLED then time out in minutes to HUP when at the command prompt Enumeration: 'default': 15, 'minimum': 1, 'maximum': 99.

IF MODEM_ENABLED then limit # of login attempts then HUP Enumeration: 'default': 3, 'minimum': 1, 'maximum': 99.

Total number of TI login attempts

Total number of FAILED User login attempts

Total number of FAILED Manager login attempts

Total number of FAILED Other login attempts

Count of TTY Frame errors

Count of TTY Overrun errors

Count of TTY Parity errors

Count of TTY Input Fifo errors

The state of the ti rui command processor. Idle is normal state. Busy indicates a command is being processed. Enumeration: 'idle': 1, 'busy': 2.

Ti command request string

The result of the Ti command requst

Total number of command requests

Total number of command requests that processed without error

Total number of command requests that could not be processed because of errors

The table of circuit names

Entry format for the table of circuit names

Creation and deletion flag for this record Enumeration: 'create': 1, 'delete': 2.

circuit number

circuit name

circuit interface type Enumeration: 'sync': 20, 't1': 30, 'token': 50, 'csmacd': 10, 'hssi': 70, 'e1': 40, 'fddi': 60.

The Circuit-Protocol mask

Table of kernel statistics, indexed by slot number

A particular interface

The slot number indexes the kernel statistics table

The total size of allocatable memory, in bytes

The amount of memory which hasn't been allocated yet, in bytes

Total number of memory segments in the kernel

Total number of unallocated memory segments in the kernel

Size of the largest unallocated memory segment

Total number of packet buffers

Number of packet buffers in the free pool

Number of tasks running

Number of tasks awaiting scheduling

Total number of timers available

Total number of timers in use by tasks

Activation address of task which owns many buffers

Number of buffers owned by the task

Activation address of task which owns many buffers

Number of buffers owned by the task

Activation address of task which owns many buffers

Number of buffers owned by the task

Activation address of task which owns many buffers

Number of buffers owned by the task

Activation address of task which owns many buffers

Number of buffers owned by the task

Activation address of task which owns many buffers

Number of buffers owned by the task

Activation address of task which owns many buffers

Number of buffers owned by the task

Activation address of task which owns many buffers

Number of buffers owned by the task

Activation address of task which owns many buffers

Number of buffers owned by the task

Activation address of task which owns many buffers

Number of buffers owned by the task

Activation address of task which owns a sizable amount of memory

Amount of memory owned by the task

Activation address of task which owns a sizable amount of memory

Amount of memory owned by the task

Activation address of task which owns a sizable amount of memory

Amount of memory owned by the task

Activation address of task which owns a sizable amount of memory

Amount of memory owned by the task

Activation address of task which owns a sizable amount of memory

Amount of memory owned by the task

Activation address of task which owns a sizable amount of memory

Amount of memory owned by the task

Activation address of task which owns a sizable amount of memory

Amount of memory owned by the task

Activation address of task which owns a sizable amount of memory

Amount of memory owned by the task

Activation address of task which owns a sizable amount of memory

Amount of memory owned by the task

Activation address of task which owns a sizable amount of memory

Amount of memory owned by the task

CSMA/CD line record

An entry in the csmacd table

create/delete parameter, dflt = created Enumeration: 'create': 1, 'delete': 2.

enable/disable parameter, dflt = enabled Enumeration: 'enable': 1, 'disable': 2.

line driver state variable, Not Present, Init, Down, Up Enumeration: 'down': 2, 'init': 3, 'up': 1, 'notpresent': 4.

instance ID Slot, filled in by driver Enumeration: 'minimum': 1, 'maximum': 14.

instance ID Connector, filled in by driver Enumeration: 'four': 4, 'three': 3, 'two': 2, 'one': 1.

cct number for this line instance Enumeration: 'minimum': 1, 'maximum': 1023.

bofl parameter, dflt = enabled Enumeration: 'enable': 1, 'disable': 2.

bofl parameter, dflt = 5 Enumeration: 'default': 5, 'minimum': 1, 'maximum': 60.

mtu parameter, fixed Enumeration: 'default': 1518.

line MAC address, fixed - line driver fills in

Number of octets received without error

Number of frames received without error

Number of octets transmitted without error

Number of frames transmitted without error

Number of deferred transmissions

Number of late collisions

Number of excessive collisions

Number of frames transmitted larger than 1518 octets

Number of internal buffer errors

Number of loss of carrier errors

Number of transmitter underflow errors

Number of receiver checksum errors

Number of receiver alignment errors

Number of receiver lack of resource errors

Number of frames received exceeding 1518 octets

Number of receiver overflow errors

Number of internal memory errors

Number of collision errors

Hardware filtering parameter. Enumeration: 'enable': 1, 'disable': 2.

Transmit Queue Length, values larger than the compiled ring size are truncated to the compiled ring size. Enumeration: 'default': 32, 'minimum': 1, 'maximum': 255.

Receive Queue Length, values larger than the compiled ring size are truncated to the compiled ring size. Enumeration: 'default': 32, 'minimum': 1, 'maximum': 255.

Number of frames clipped in driver's transmit routine due to transmit congestion.

Number of packet buffer misses while attempting to replenish driver receive ring.

TOKEN RING line record

An entry in the token table

create/delete parameter. Enumeration: 'deleted': 2, 'created': 1.

enable/disable parameter. Enumeration: 'disabled': 2, 'enabled': 1.

line driver state variable, Not Present, Init, Down, Up Enumeration: 'down': 2, 'init': 3, 'up': 1, 'notpresent': 4.

instance ID Slot, filled in by driver Enumeration: 'minimum': 1, 'maximum': 14.

instance ID Connector, filled in by driver Enumeration: 'two': 2, 'one': 1.

cct number for this line instance, configuration required Enumeration: 'minimum': 1, 'maximum': 1023.

mtu parameter, fixed. This mtu of 4568 allows a type 3 Source Route Frame (info=4472) to be IP encapsulated over Token Ring. The components are: AC_FC (2) + SNAP (12+8) + SNAP_IP (12+8+20) + SR (12+18) + TYPE3_INFO (4472) + FCS (4) --------------------- total 4568 bytes Enumeration: 'default': 4568.

line MAC address, line driver fills in the currently used 48 bit MAC address.

Configured line MAC address. Only used if wfTokenRingMadrSelect is set appropriately.

Selector determines which MAC address the interface will use. Enumeration: 'prom': 2, 'boxwide': 1, 'cnfg': 3.

Token Ring speed parameter - 4 and 16 Mbps are only valid values Enumeration: 'mbps16': 16777216, 'mbps4': 4194304.

Early Token Release parameter, only valid with 16Mbps Enumeration: 'disabled': 2, 'enabled': 1.

The current interface status. This attribute is only valid when the wfTokenRingOpenState attribute is set to OPENED. The attribute's value is a sum of values, one for each currently applicable condition (ie, bit positions indicate active conditions). Occurrences of each condition are separately counted and the counts are included in this MIB as attributes wfTokenRingSignalLosses through wfTokenRingRingRecoveries. The following values are defined: 32768 = Signal Losses 16384 = Hard Errors 8192 = Soft Errors 4096 = Transmit Beacons 2048 = Lobe Wire Faults 1024 = Auto-Removal Errors 256 = Remove Received 128 = Counter Overflows 64 = Single Stations 32 = Ring Recoveries This attribute is the most recent sum of these conditions. More information on each condition is include in the descriptions of the individual counter attributes.

The current interface state with respect to entering or leaving the ring. Enumeration: 'ringfailure': 5, 'opened': 1, 'opening': 2, 'openfailure': 4, 'closed': 6, 'closing': 3.

Indicates the success, or the reason for failure, of the station's most recent attempt to enter the ring. Enumeration: 'insertiontimeout': 5, 'unkerror': 11, 'ringfailed': 6, 'lobefailed': 3, 'removereceived': 10, 'requestfailed': 9, 'duplicatemac': 8, 'noopen': 12, 'badparam': 2, 'signalloss': 4, 'open': 1, 'beaconing': 7.

MAC address of Up Stream neighbor. Only valid when 'opened'.

Number of octets received without error.

Number of frames received without error.

Number of octets transmitted without error.

Number of frames transmitted without error.

Number of error-free inbound packets discarded. Usually due to lack of memory resources. This is equivalent to wfTokenRingRxCongestionErrors.

Number of inbound packets not delivered to higher-layer protocol due to errors. The sum of wfTokenRingLineErrors and wfTokenRingBurstErrors.

Number of error-free outbound packets discarded. Usually due to lack of transmission bandwidth. This is equivalent to wfTokenRingTxClipFrames.

Number of outbound packets that could not be transmitted because of errors. This is equivalent to wfTokenRingLostFrameErrors.

Number of frames clipped in driver's transmit routine due to transmit congestion.

Number of packet buffer misses while attempting to replenish driver receive ring.

Number of ring signal losses detected.

Number of events causing the adapter to transmit or receive beacon MAC frames.

Number of soft errors. Corresponds to the number of Report Error MAC frames transmitted by this station.

Number of events causing the adapter to transmit beacon frames.

Number of opens or shorts (cable faults) between the adapter and the MAU.

Number of lobe wrap test failures during beacon auto_removal process.

Number of Remove Ring Station MAC frames received. Each frame causes this station to leave the ring.

Number of adapter error counter overflows.

Number of ring status change interrupts while adapter is only station on the ring.

Number of claim token MAC frames (ring recoveries) observed on the ring.

Number of internal adapter errors that result in adapter crashes.

Adapter Check Code of first occurrence.

Adapter Check Code of most recent (last) occurrence.

Number of frames copied or repeated by this station with bad format or an FCS error.

Number of errored frames with no transition for 5 1/2 bit times.

Number of occurrences of this station receiving both an AMP MAC frame and a SMP MAC frame with the a & c bits clear or more than one SMP MAC frame with the a & c bits clear without an intervening AMP MAC frame. This condition indicates that the up-stream neighbor is unable to set the a & c bits in a frame that it has copied.

Number of frames being stripped which are missing their tails.

Number of frames dropped due to receive congestion.

Number of specifically addressed frames for this station that had their a & c bits previously set.

Number of token protocol errors. Only relevant when this station is the active monitor.

Number of bus errors during DMA that do not exceed threshold.

Number of parity errors during DMA that do not exceed threshold.

Number of host to adapter commands aborted because of in-completed in process commands.

Number of processings of received frames (similar to RINT).

Number of processings of frames for transmit.

Number of processings of transmitted frames (similar to TINT).

Number of re-initializations due to receiver time-outs.

Number of re-initializations due to command time-outs.

Number of re-initializations due to receive host interface errors.

Internal Adapter RAM buffer size.

FDDI line record

An entry in the FDDI table

create/delete parameter, default = created Enumeration: 'create': 1, 'delete': 2.

enable/disable parameter, default = enabled Enumeration: 'enable': 1, 'disable': 2.

line driver state variable, not present, init, down, up Enumeration: 'down': 2, 'init': 3, 'up': 1, 'notpresent': 4.

instance ID slot - filled in by driver Enumeration: 'minimum': 1, 'maximum': 14.

instance ID Node - filled in by driver Enumeration: 'two': 2, 'one': 1.

cct number for this line instance Enumeration: 'minimum': 1, 'maximum': 1023.

bofl parameter, default = enabled Enumeration: 'enable': 1, 'disable': 2.

bofl parameter, default = 5 seconds Enumeration: 'default': 5, 'minimum': 1, 'maximum': 60.

mtu parameter, fixed Enumeration: 'default': 4495.

line MAC address, fixed - line driver fills in

Number of bytes received without error

Number of frames received without error

Number of bytes transmitted without error

Number of frames transmitted without error

Number of frames received with CRC errors

Number of frames received with internal overrun errors

Number of frames received with parity errors

Number of frames received with mac errors

Number of receive ring error events

Number of SMT receive ring error events

Number of LLC receive ring overrun events

Number of SMT receive ring overrun events

Number of transmit frames with internal abort errors

Number of transmit frames aborted with underrun errors

Number of transmit frames aborted with parity errors

Number of LLC/SMT transmit ring error events

Number of port operation error events

Number of internal operation error events

Number of host error events

A value that indicates the connection policies enforced at the station. A station sets the corresponding policy for each of the connection types that it rejects. The letter designations, X and Y, in the 'rejectX-Y' names have the following significance: X represents the PC-Type of the local PORT and Y represents a PC-Neighbor in the evaluation of Connection-Policy (PC-Type, PC- Neighbor) that is done to determine the setting of T-Val(3) in the PC-Signaling sequence. The value is a sum. This value initially takes the value zero, then for each of the connection policies currently enforced on the node, 2 raised to a power is added to the sum. The powers are according to the following table: Policy Power rejectA-A 0 rejectA-B 1 rejectA-S 2 rejectA-M 3 rejectB-A 4 rejectB-B 5 rejectB-S 6 rejectB-M 7 rejectS-A 8 rejectS-B 9 rejectS-S 10 rejectS-M 11 rejectM-A 12 rejectM-B 13 rejectM-S 14 rejectM-M 15 Enumeration: 'default': 65381.

The timer used in the Neighbor Notification protocol, reported in seconds and ranging from 2 to 30 seconds. Enumeration: 'default': 22, 'max': 30, 'min': 2.

The requested Target Token Rotation Time (TTRT) for a MAC's synchronous traffic represented in unsigned integer specifying time in octet units (80 nanoseconds). Enumeration: 'default': 2062500.

The requested maximum TTRT to be supported by a MAC represented in unsigned integer specifying time in octet units (80 nanoseconds). Enumeration: 'default': 2097152.

The requested value of TvxValue represented in unsigned integer specifying time in octet units (80 nanoseconds). Enumeration: 'default': 32768.

The requested minimum TTRT to be requested by a MAC represented in unsigned integer specifying time in octet units (80 nanoseconds). Enumeration: 'default': 50000.

Hardware filter (CAM) parameter. Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'enable': 1, 'disable': 2.

Transmit Queue Length, values larger than the compiled ring size are truncated to the compiled ring size. Enumeration: 'default': 127, 'minimum': 1, 'maximum': 255.

Receive Queue Length, values larger than the compiled ring size are truncated to the compiled ring size. Enumeration: 'default': 64, 'minimum': 1, 'maximum': 255.

Number of frames clipped in driver's transmit routine due to transmit congestion.

Number of packet buffer misses while attempting to replenish driver receive ring.

SYNC line record

An entry in the SYNC table

Create/Delete parameter Enumeration: 'deleted': 2, 'created': 1.

Enable/Disable parameter Enumeration: 'disabled': 2, 'enabled': 1.

Line Driver state variable, Not Present, Init, Down, Up Enumeration: 'down': 2, 'init': 3, 'up': 1, 'notpresent': 5, 'wait': 4.

Instance ID Slot, filled in by driver Enumeration: 'minimum': 1, 'maximum': 14.

Instance ID Connector, filled in by driver Enumeration: 'four': 4, 'three': 3, 'two': 2, 'one': 1.

CCT number for this line instance Enumeration: 'minimum': 1, 'maximum': 1023.

breath of life parameter Enumeration: 'disabled': 2, 'enabled': 1.

breath of life timeout in seconds Enumeration: 'default': 5, 'minimum': 1, 'maximum': 60.

MTU parameter, this is buffer size for SYNC media, fixed Enumeration: 'default': 1600, 'minimum': 3, 'maximum': 4500.

Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom for this connector.

The promiscuous parameter allows address filtering based on the local and remote addresses. When enabled, all frames are received, disabled indicates only frames destined for this local address are received Enumeration: 'disabled': 2, 'enabled': 1.

XID enable/disable parameter. This parameter is used to enable or disable transmission/reception of Test XID frames. Enumeration: 'disabled': 2, 'enabled': 1.

Tx/Rx clock source is either internally or external generated. Enumeration: 'internal': 1, 'external': 2.

Tx/Rx clock speed. This speed selection is valid only when the internal clock speed parameter has been selected. Enumeration: 'clk2mb': 2500000, 'clk125k': 125000, 'clk19200b': 19230, 'clk32000b': 32051, 'clk833k': 833333, 'clk5mb': 5000000, 'clk1mb': 1250000, 'clk1200b': 1200, 'clk230k': 227272, 'clk2400b': 2401, 'clk625k': 625000, 'clk38400b': 38461, 'clk64k': 64102, 'clk420k': 416666, 'clk9600b': 9615, 'clk4800b': 4807, 'clk7200b': 7204, 'clk56k': 56818.

The signal mode parameter indicates the line paramter balanced or unbalanced. Enumeration: 'balanced': 1, 'unbalanced': 2.

The RTS parameter enables/disables detection of RTS signals on the interface. Normal default mode is running without RTS enabled. Enumeration: 'disabled': 2, 'enabled': 1.

Allows single or multiple DMA burst cycles. When enabled the chip performs 8 word burst's. Single word cycles are performed when disabled Enumeration: 'disabled': 2, 'enabled': 1.

Service type for this circuit. Transparent is raw HDLC mode, LLC1 will prefix the HDLC address and control fields to the frame. The LLC2 service provides the LAPB protocol service. Enumeration: 'llc1': 2, 'transparent': 1, 'llc2': 3.

The Retry count parameter indicates the number of retransmission attempts which will be tried per frame before a line is determined to be down. The retry count is max attempts following expiration of the T1 timer. This parameter is equal to the N2 counter in ICB. Enumeration: 'default': 16, 'minimum': 1, 'maximum': 64.

The link idle parameter is the number of seconds before a line has been determined to be idle. An idle line is considered disconnectd This value is expressed in seconds. Enumeration: 'default': 3, 'minimum': 1, 'maximum': 9999.

The Retry Timer parameter indicates the timeout in seconds for a response to be heard form the link. Link control frames are sent at the expiration of this timer value. The frames will be resent up to retry count (N2) at which time the link will be disconnected. Enumeration: 'default': 3, 'minimum': 1, 'maximum': 9999.

This parameter controls length determination of the address field. When this parameter is enabled, the first bit of the address field be tested to determine the length of address field in octets. Enumeration: 'disabled': 2, 'enabled': 1.

When this parameter is enabled, the receiver will assume that all address fields are 2 octets in length regardless of the first two bits of the control field. Usefull only in Transparent Mode. Enumeration: 'disabled': 2, 'enabled': 1.

This parameter allows the control fields of all S and I frames to become 2 octets in length instead of one. Numbering of all I frame become modulo 128 instead of modulo 8. The control field of U frames remains one octet in length. Enumeration: 'disabled': 2, 'enabled': 1.

This parameter when enabled will force all control fields to become two octets in length regardless the first two bits in the control field. Usefull only in Transparent Mode. (LLC1) Enumeration: 'disabled': 2, 'enabled': 1.

This parameter controls the number of connection attempts which will be made during a LAPB connection request. This parameter is applicable only during LLC2 service. Enumeration: 'default': 10, 'minimum': 1, 'maximum': 9999.

The window size parameter controls the number of I frames which may be transmitted without acknowledgement. Non EXTC mode. Enumeration: 'default': 1, 'minimum': 1, 'maximum': 7.

The window size parameter controls the number of I frames which may be transmitted without acknowledgement in EXTC mode. Enumeration: 'default': 1, 'minimum': 1, 'maximum': 7.

The minimum frame spacing parameter defines the number of flags that are transmitted between adjacent frames. Enumeration: 'default': 1, 'minimum': 1, 'maximum': 32.

The local address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set. Enumeration: 'addressdce': 3, 'addressexplicit': 7, 'addressdte': 1.

The remote address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set. Enumeration: 'addressdce': 3, 'addressexplicit': 7, 'addressdte': 1.

48 bit MAC address of Local end of Sync Passthru circuit

48 bit MAC address of Remote end of Sync Passthru circuit

WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface. Enumeration: 'passthr': 2, 'smds': 4, 'ppp': 3, 'framerelay': 5, 'standard': 1.

CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC Enumeration: 'crc16bit': 1, 'crc32bit': 2.

Number of octets received without error

Number of frames received without error

Number of octets transmitted without error

Number of frames transmitted without error

Number of receive errors

Number of transmission errors

Number of Rx frames dropped due to lack of buffer resources

Number of Tx frames dropped due to lack of buffer resources

Number of transmission underflows, device FIFO went empty before next DMA request was granted.

Number of reject frames which were transmitted

Number of reject frames which were received

Number of receive overflows, device FIFO overflowed before next DMA cycle granted. No buffer resources available.

Number of frames which were incompletely received. These are frames which may have resulted from FRMRR errors.

Number of bad receive frames, caused by FCS errors or non octet aligned.

Number of Frame Rejects received

Number of runt frames received

Number of T1 timeout's detected. The T1 timer is the link retransmission timer. Link control frames will be retransmitted when T1 expires. This is a count of the number of timeouts.

Number of memory access errors detected. A MERR is the expiration of a DMA cycle without the bus being granted within 26us.

Media type selection is provided via this parameter Enumeration: 'default': 1, 'e1': 3, 't1': 2.

The following table will contain information about a collection of Hardware Filter (HWF) driver records. Only one HWF driver may be spawned, by the loader, on a given slot. Hence, only the slot number is used as the instance identifier into the table.

Slot number used as instance identifier.

Create/delete parameter. Enumeration: 'deleted': 2, 'created': 1.

Enable/disable parameter. Enumeration: 'disabled': 2, 'enabled': 1.

Driver state variable. Enumeration: 'down': 2, 'init': 3, 'up': 1, 'notpresent': 4.

Slot number -- instance ID. Enumeration: 'minimum': 1, 'maximum': 14.

Number of available lines on module.

The following table will contain information about a collection of Hardware Filter (HWF) line records.

Slot number and line number used as instance identifier.

State of filtering hardware on a per line basis. Enumeration: 'disabled': 2, 'full': 3, 'operational': 1.

Slot number -- instance ID.

Line number -- instance ID. Enumeration: 'four': 4, 'three': 3, 'two': 2, 'one': 1.

Circuit number associated with a line.

This attribute specifies the maximum number of table entries capable of being used by a line based upon actual hardware filter devices present and available.

Current capacity of the hardware filter table. Hardware filter table resources are dynamically allocated (in increments of 256) on an as-needed basis up to the available table size.

Number of hardware filter table entries used.

Number of frames dropped because of hardware filter match.

HSSI line record

An entry in the HSSI table

Create/Delete parameter Enumeration: 'deleted': 2, 'created': 1.

Enable/Disable parameter Enumeration: 'disabled': 2, 'enabled': 1.

Line Driver state variable, Not Present, Init, Down, Up Enumeration: 'boflwait': 3, 'up': 1, 'init': 5, 'cawait': 4, 'notpresent': 6, 'lmiwait': 2.

Instance ID Slot, filled in by driver Enumeration: 'minimum': 1, 'maximum': 14.

Instance ID Connector, filled in by driver Enumeration: 'four': 4, 'three': 3, 'two': 2, 'one': 1.

CCT number for this line instance Enumeration: 'minimum': 1, 'maximum': 1023.

breath of life parameter Enumeration: 'disabled': 2, 'enabled': 1.

breath of life frequency in seconds Enumeration: 'default': 1, 'minimum': 1, 'maximum': 60.

MTU parameter, this is buffer size for HSSI media, fixed Enumeration: 'default': 4495, 'minimum': 3, 'maximum': 4500.

Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom for this connector.

Service type for this circuit. Transparent is raw HDLC mode, and is the only service provided on the current HSSI product Enumeration: 'transparent': 1, 'undefined': 2.

WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface. Enumeration: 'passthr': 2, 'smds': 4, 'ppp': 3, 'framerelay': 5, 'standard': 1.

T1 or T3, in the future OC1, OC3 and OC12. Used for MIB selection Enumeration: 'dsone': 1, 'dsthree': 3.

External Clock Speed, Used in the future for route selection Enumeration: 'default': 46359642, 'minimum': 307200, 'maximum': 52638515.

CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC Enumeration: 'crc16bit': 1, 'crc32bit': 2.

Enables internal transmit clock generation. Should NEVER be enabled for normal operation. Enumeration: 'disabled': 2, 'enabled': 1.

Number of bytes received without error

Number of frames received without error

Number of bytes transmitted without error

Number of frames transmitted without error

Number of error-free inbound packets discarded. Usually due to lack of memory resources.

Number of inbound packets not delivered to higher-layer protocol because of errors.

Number of error-free outbound packets discarded. Usually due to lack of transmission bandwidth.

Number of outbound packets that could not be transmitted because of errors.

Number of Long frames dropped on receive because of length

Number of frames clipped in the transmit routine

Number of failed attempts by the line driver to aquire a packet buffer

Last errored receive descriptor's control field

Number of frames received with CRC errors

Number of frames received with fifo overrun errors

Number of frames received with abort status

Last errored transmit descriptor's control field

Number of transmit frames with internal abort errors

Number of transmit frames aborted with underrun errors

Number of receive ring error events

Last 8 bit value from the recv ring state register

Number of receive ring overrun events

Number of transmit ring error events

Last 8 bit value from the transmit ring state register

Number of port operation error events

Number of internal operation error events

Number of parity errs on host accesses to directly accessable registers.

Number of receive frame processings (RINT)

Number of transmit processings, invokations of transmit routine

Number of transmit complete processings (TINT)

Number of Interrupt processings, invokations of intr routine

Number of breath of life packets per breath of life Enumeration: 'default': 5, 'minimum': 1, 'maximum': 127.

breath of life packet length Enumeration: 'default': 100, 'minimum': 22, 'maximum': 4450.

Performance tunning parameter controls Receive buffer size. Enumeration: 'length4k': 64, 'length8k': 128.

Performance tunning parameter controls device memory access burst length. Enumeration: 'length256': 3, 'length32': 1.

Performance tunning parameter controls the receive queue length. Receive Queue Length, values larger than the compiled ring size are truncated to the compiled ring size. Enumeration: 'default': 64, 'minimum': 1, 'maximum': 255.

Performance tunning parameter controls the transmit queue length. Transmit Queue Length, values larger than the compiled ring size are truncated to the compiled ring size. Enumeration: 'default': 127, 'minimum': 1, 'maximum': 255.

Performance tunning parameter controls the receive watermark. Enumeration: 'default': 2, 'minimum': 2, 'maximum': 255.

Performance tunning parameter controls the transmit watermark. Enumeration: 'default': 16, 'minimum': 2, 'maximum': 255.

Performance tunning parameter controls fifo area allowed for receive. Enumeration: 'default': 1, 'minimum': 1, 'maximum': 255.

Only for DEBUG. Enumeration: 'default': 1, 'ace32': 3, 'ace25': 2.

Only for DEBUG, Turbo breath of life parameter Enumeration: 'disabled': 2, 'enabled': 1.

T1 line record

An entry in the T1 table

create/delete parameter, dflt = created Enumeration: 'deleted': 2, 'created': 1.

enable/disable parameter, dflt = enabled Enumeration: 'disabled': 2, 'enabled': 1.

line driver state variable, Not Present, Init, Up Enumeration: 'notpresent': 4, 'init': 3, 'up': 1.

instance ID Slot, filled in by driver Enumeration: 'minimum': 1, 'maximum': 14.

instance ID Connector, filled in by driver Enumeration: 'two': 2, 'one': 1.

Line mac address, filled in by driver

Frame Type - differentiates between two tarrifed framing formats D4 and ESF. Enumeration: 'esf': 2, 'd4': 1.

Line Buildout - Approximate length of cable Enumeration: 'default': 1, 'minimum': 1, 'maximum': 655.

B8ZS Support - Enables or disables Binary 8 zeros suppression Enumeration: 'disabled': 2, 'enabled': 1.

Clock Mode - Specifies the source of the T1 transmit clock Enumeration: 'default': 1, 'manual': 4, 'internal': 1, 'slave': 2.

MiniDacs Configuration - assigns each T1 channel to a specific function

Number of Bipolar Violations

Number of frame bit errors

Number of Out of Frame errors

Number of Superframe errors

Number of Yellow Alarms Received

Number of instances of carrier loss

Number of Red Alarm Received

E1 line record

An entry in the E1 table

create/delete parameter, dflt = created Enumeration: 'deleted': 2, 'created': 1.

enable/disable parameter, dflt = enabled Enumeration: 'disabled': 2, 'enabled': 1.

line driver state variable, Not Present, Init, Up Enumeration: 'notpresent': 4, 'init': 3, 'up': 1.

instance ID Slot, filled in by driver Enumeration: 'minimum': 1, 'maximum': 14.

instance ID Connector, filled in by driver Enumeration: 'two': 2, 'one': 1.

Line mac address, filled in by driver

HDB3 Support - Enables or disables high density bipolar coding Enumeration: 'disabled': 2, 'enabled': 1.

Clock Mode - Specifies the source of the E1 transmit clock Enumeration: 'default': 1, 'manual': 4, 'internal': 1, 'slave': 2.

MiniDacs Configuration - assigns each E1 channel to a specific function

Number of Bipolar Violations

Number of Frame errors

Number of remote alarms received

Number of Multiframe Alarms Received

Number of instances of CAS Multiframe resync criteria met

Number of instances of sync loss

Number of instances of receive signalling all 1's

Number of instances of Receive unframed all 1's

The DS1 Configuration table

per circuit DS1 configuration objects; wfDs1LineIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

1..900 seconds within the current 15-minute interval

0..96 previous intervals that valid data were collected. This is 96 unless the CSU device was brought on line within the last 24 hours.

the variety of DS1 implementing this circuit Enumeration: 'ds1ansi-esf': 4.

the variety of Zero Code Suppression used on the link Enumeration: 'ds1b8zs': 2, 'ds1zbtsi': 5.

the type of code being sent across the DS1 circuit by the CSU Enumeration: 'ds1sendnocode': 2.

the transmission vendor's circuit identifier

the loopback state of the CSU Enumeration: 'ds1mgrpayloadloop': 2, 'ds1noloop': 1, 'ds1mgrlineloop': 3, 'ds1otherloop': 6, 'ds1netreqpayloadloop': 4, 'ds1netreqlineloop': 5.

the state of the DS1 line Enumeration: 'ds1lossofframe': 8, 'ds1loopbackstate': 32, 'ds1farendalarm': 2, 'ds1alarmindicationsignal': 4, 'ds1noalarm': 1, 'ds1lossofsignal': 16.

The DS1 Current table

per circuit DS1 current objects - wfDs1CurrentIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

the count of errored seconds in the current interval

the count of severely errored seconds in the current interval

the count of severely errored framing seconds in the current interval

the number of unavailable seconds in the current interval

the count of bipolar violations in the current interval

the count of code violation error events in the current interval

The DS1 Interval table

per circuit DS1 interval objects - wfDs1IntervalIndex corresponds to Wellfleet circuit number, wfDs1IntervalNumber is the numbered previous 15-minute interval

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

1..96 where 1 is the most recent 15-minute interval and 96 is the least Enumeration: 'minimum': 1, 'maximum': 96.

the count of errored seconds in the specified interval

the count of severely errored seconds in the specified interval

the count of severely errored framing seconds in the specified interval

the number of unavailable seconds in the specified interval

the count of bipolar violations in the specified interval

the count of code violation error events in the specified interval

The DS1 Total table

per circuit DS1 total objects - wfDs1TotalIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

total count of errored seconds

total count of severely errored seconds

total count of severely errored framing seconds

total number of unavailable seconds

total count of bipolar violations

total count of code violation error events

The DS1 Far End Current table

per circuit DS1 far end current objects wfDs1CurrentIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

the count of errored seconds in the current interval

the count of severely errored seconds in the current interval

the count of severely errored framing seconds in the current interval

the count of bipolar violations in the current interval

the count of code violation error events in the current interval

The DS1 Far End Interval table

per circuit DS1 far end interval objects - wfDs1FeIntervalIndex corresponds to Wellfleet circuit number, wfDs1FeIntervalNumber is the numbered previous 15-minute interval

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

1..96 where 1 is the most recent 15-minute interval and 96 is the least Enumeration: 'minimum': 1, 'maximum': 96.

the count of errored seconds in the specified interval

the count of severely errored seconds in the specified interval

the count of severely errored framing seconds in the specified interval

the count of bipolar violations in the specified interval

the count of code violation error events in the specified interval

The DS1 Far End Total table

per circuit DS1 far end total objects - wfDs1FeTotalIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

total count of errored seconds

total count of severely errored seconds

total count of severely errored framing seconds

total count of bipolar violations

total count of code violation error events

The DS3 Configuration table

per circuit DS3 configuration objects; wfDs3LineIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

1..900 seconds within the current 15-minute interval

0..96 previous intervals that valid data were collected. This is 96 unless the CSU device was brought on line within the last 24 hours.

the variety of DS3 implementing this circuit Enumeration: 'ds3cbitparity': 4, 'ds3clearchannel': 5, 'other': 1.

the variety of Zero Code Suppression used on the link Enumeration: 'ds3b3zs': 2.

the type of code being sent across the DS3 circuit by the CSU Enumeration: 'ds3sendnocode': 2.

the transmission vendor's circuit identifier

the loopback state of the CSU Enumeration: 'ds3mgrlineloop': 3, 'ds3netreqlineloop': 5, 'ds3netreqpayloadloop': 4, 'ds3otherloop': 6, 'ds3noloop': 1, 'ds3mgrpayloadloop': 2.

the state of the DS3 line Enumeration: 'ds3noalarm': 1, 'ds3lossofsignal': 16, 'ds3lossofframe': 8, 'ds3alarmindicationsignal': 4, 'ds3loopbackstate': 32, 'ds3farendalarm': 2.

The DS3 Current table

per circuit DS3 current objects - wfDs3CurrentIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

the count of errored seconds in the current interval

the count of severely errored seconds in the current interval

the count of severely errored framing seconds in the current interval

the number of unavailable seconds in the current interval

the count of bipolar violations in the current interval

the count of code violation error events in the current interval

The DS3 Interval table

per circuit DS3 interval objects - wfDs3IntervalIndex corresponds to Wellfleet circuit number, wfDs3IntervalNumber is the numbered previous 15-minute interval

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

1..96 where 1 is the most recent 15-minute interval and 96 is the least Enumeration: 'minimum': 1, 'maximum': 96.

the count of errored seconds in the specified interval

the count of severely errored seconds in the specified interval

the count of severely errored framing seconds in the specified interval

the number of unavailable seconds in the specified interval

the count of bipolar violations in the specified interval

the count of code violation error events in the specified interval

The DS3 Total table

per circuit DS3 total objects - wfDs3TotalIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

total count of errored seconds

total count of severely errored seconds

total count of severely errored framing seconds

total number of unavailable seconds

total count of bipolar violations

total count of code violation error events

The DS3 Far End Configuration table

per circuit DS3 far end config objects - wfDs3FeIntervalIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

equipment description code - C-bit parity only

equipment location code - C-bit parity only

code for the equipment location within a building

code for the equipment location within a bay

path identification code

The DS3 Far End Current table

per circuit DS3 far end current objects wfDs3FeCurrentIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

the count of errored seconds in the current interval

the count of severely errored seconds in the current interval

the count of code violation error events in the current interval

The DS3 Far End Interval table

per circuit DS3 far end interval objects - wfDs3FeIntervalIndex corresponds to Wellfleet circuit number, wfDs3FeIntervalNumber is the numbered previous 15-minute interval

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

1..96 where 1 is the most recent 15-minute interval and 96 is the least Enumeration: 'minimum': 1, 'maximum': 96.

the count of errored seconds in the specified interval

the count of severely errored seconds in the specified interval

the count of code violation error events in the specified interval

The DS3 Far End Total table

per circuit far end DS3 total objects - wfDs3FeTotalIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

total count of errored seconds

total count of severely errored seconds

total count of code violation error events

The SIP L2 Table

per circuit SIP Level 2 objects - wfSipL2Index corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

total of unerrored received SIP L2 PDUs

total of unerrored SIP L2 PDU's sent across the SNI

total SIP L2 PDUs with HCS or CRC errors

total SIP L2 PDUs with length errors

total SIP L2 PDUs with unexpected sequence numbers

number of SIP L2 PDUs with BOMs previously started

number of SIP L2 PDUs with zero BOMs or SSMs not zero

number of SIP L2 PDUs with zero EOMs or EOMs without BOMs

The SIP DS1 PLCP Table

per circuit DS1 PLCP objects - wfSipDs1PlcpIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

number of second intervals containing one or more severely errored seconds

alarm state Enumeration: 'incominglof': 3, 'noalarm': 1, 'receivedfarendalarm': 2.

number of second intervals containing one or more unavailable seconds

The SIP DS3 PLCP Table

per circuit DS3 PLCP objects - wfSipDs3PlcpIndex corresponds to Wellfleet circuit number

this corresponds to the Wellfleet circuit number Enumeration: 'minimum': 1, 'maximum': 1024.

number of second intervals containing one or more severely errored seconds

alarm state Enumeration: 'incominglof': 3, 'noalarm': 1, 'receivedfarendalarm': 2.

number of second intervals containing one or more unavailable seconds

A list of SMT entries.

An SMT entry containing information common to a given SMT.

Slot number associated with an SMT entity.

Node/connector number associated with an SMT entity.

Circuit number associated with an SMT entity.

Unique identifier of an FDDI station.

The version that this station is using for its operation.

The number of MACs in the station or concentrator.

The number of Non Master PORTs (A, B, or S PORTs) in the station or concentrator.

Indicates the current state of the ECM state machine. Enumeration: 'insert': 6, 'trace': 3, 'leave': 4, 'deinsert': 8, 'in': 2, 'pathtest': 5, 'check': 7, 'out': 1.

The attachment configuration for the station or concentrator. Enumeration: 'wraps': 2, 'wrapab': 5, 'isolated': 1, 'wrapa': 3, 'wrapb': 4, 'thr': 6.

A list of MAC entries.

A MAC entry containing information common to a given MAC.

Slot number associated with a MAC entity.

Node/connector number associated with a MAC entity.

Circuit number associated with a MAC entity.

The MAC's upstream neighbor's long individual MAC address. It may be determined by the Neighbor Information Frame protocol. The value shall be reported as '00 00 00 00 00 00' if it is unknown.

The MAC's downstream neighbor's long individual MAC address. It may be determined by the Neighbor Information Frame protocol. The value shall be reported as '00 00 00 00 00 00' if it is unknown.

The 48 bit individual address of the MAC used for SMT frames.

The negotiated TTRT during the claim process represented in unsigned integer specifying time in octet units (80 nanosecond).

Indicates the current state of the Ring Management state machine. Enumeration: 'directed': 64, 'detect': 8, 'trace': 128, 'ringop': 4, 'isolated': 1, 'nonopdup': 16, 'nonop': 2, 'ringopdup': 32.

A list of PORT entries. The number of entries is given by the value of wfFddiPortNumber.

A PORT entry containing information common to a given PORT.

Slot number associated with a PORT entity.

Node/connector number associated with a PORT entity.

Circuit number associated with a PORT entity.

A unique value for each PORT associated with each slot/connector pair.

PC_Type. Enumeration: 'a': 1, 's': 3, 'b': 2, 'm': 4.

The type (PC_Neighbor) of the remote PORT that is determined in PC_Signaling in R_Val (1,2). Enumeration: 'a': 1, 'unknown': 5, 's': 3, 'b': 2, 'm': 4.

State of Physical State Machine. Enumeration: 'off': 1, 'trace': 3, 'verify': 8, 'signal': 6, 'maint': 10, 'next': 5, 'break': 2, 'connect': 4, 'active': 9, 'join': 7.

Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the bridge. Enumeration: 'deleted': 2, 'created': 1.

Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable the bridge. Enumeration: 'disabled': 2, 'enabled': 1.

The current state of the entire Bridge. Enumeration: 'down': 2, 'init': 3, 'up': 1, 'pres': 4.

A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame. inst = wfBrTpBaseFdbAddress

An entry in the wfBrTpFdbTable.

A unicast MAC address for which the bridge has forwarding and/or filtering information.

The port number on which the wfBrTpBaseFdbAddress was learned.

The status of this entry. The meanings of the values are: learned(3) : the value of the corresponding instance of wfBrTpFdbPort was learned, and is being used. Enumeration: 'learned': 3.

Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the bridge. Enumeration: 'deleted': 2, 'created': 1.

Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable the bridge. Enumeration: 'disabled': 2, 'enabled': 1.

The current state of the SR bridge. Enumeration: 'down': 2, 'init': 3, 'up': 1, 'notpresent': 4.

The SR bridge internal LAN ID

The SR bridge Id

The SR bridge Group LAN ID

IP Encapsulation Enable/Disable Enumeration: 'disabled': 2, 'enabled': 1.

The ring number of a connected IP network

The number IP frames received by the network

The number IP frames received by the network

to the LF code in the Route Control field

A table that contains information about every interface that is associated with this source routing bridge. inst_id[1] = wfBrSrInterfaceCircuit

An entry in wfBrSrInterface.

Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an interface. Enumeration: 'deleted': 2, 'created': 1.

Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable an interface. Enumeration: 'disabled': 2, 'enabled': 1.

The current state of the interface. Enumeration: 'down': 2, 'init': 3, 'up': 1, 'notpresent': 4.

The circuit that this interface runs over.

The maximum number of RDs permitted in incoming explorer frames

The ring number of the source routing circuit. Even non-ring circuit need a ring number if it is to do source routing

Enables blocking of outbound STEs Enumeration: 'accept': 2, 'block': 1.

Enables blocking of inbound STEs Enumeration: 'accept': 2, 'block': 1.

Enables blocking of inbound explorers that have have already been through the IP network Enumeration: 'accept': 2, 'block': 1.

Ip address for this ring. This should match the the IP address in the IP MIB

The number of frames that have been received by this interface from its circuit.

The number of frames that have been transmitted by this interface

The number of frames that have been transmitted by this interface to the IP network

Count of frames received which were discarded because of a bad Route Control field

Count of frames received which were discarded because of a invalid incoming ring

Count of specifically routed frames received which were discarded due to filtering or no next circuit

A table that contains the bridge numbers used by Wellfleet bridges in a source routing network inst_id[2] = wfBrSrBridgeId

An entry in wfBrSrBridge.

Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an IP encapsulation peer record. Enumeration: 'deleted': 2, 'created': 1.

The Bridge Id reserved for Wellfleet bridges

A table that contains the table of IP addresses to which source routing explorers should be sent inst_id[2] = wfBrSrIpExplorerAddress

An entry in wfBrSrIpExplorer.

Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an IP encapsulation peer record. Enumeration: 'deleted': 2, 'created': 1.

The IP address of this encapsulation peer.

A table that contains information about IP Encapsulation ring-to-IP Address mappings. This information is used to make the 'next ring' IP Address decision. inst = wfBrSrIpEncapsRing

An entry in the wfBrSrIpEncapsTable.

The remote ring number for which we have a ring to IP Address mapping.

The IP Address of the Wellfleet IP Encapsulation peer to which this ring is connected.

The status of this entry. The meanings of the values are: learned(3) : the value of the corresponding instance of wfBrSrIpEncapsRing was learned, and is being used. Enumeration: 'learned': 3.

SR Bridge Traffic Filters

An entry in WfBrSrTrafficFilterTable.

Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted. Enumeration: 'deleted': 2, 'created': 1.

Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule. Enumeration: 'disabled': 2, 'enabled': 1.

Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule. Enumeration: 'active': 1, 'inactive': 3, 'error': 2.

The number of received packets that have matched this rule.

The filter rule definition.

Reserved field.

The ID of the Bridge Circuit to which the filter is applied.

ID for the rule.

Fragment number - for large rules.

A table that contains the currently active RIFs in use by Router End Station Support inst_id[9] = wfBrSrIpExplorerAddress

An entry in wfBrSrEsRif.