Wellfleet-DS3E3-MIB: View SNMP OID List / Download MIB

VENDOR: WELLFLEET


 Home MIB: Wellfleet-DS3E3-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, SNMPv2-TC, Wellfleet-COMMON-MIB

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 wfDs3E3ConfigTable 1.3.6.1.4.1.18.3.4.26.10 no-access
The DS3/E3 Configuration table
       wfDs3E3ConfigEntry 1.3.6.1.4.1.18.3.4.26.10.1 no-access
per circuit DS3/E3 configuration objects; wfDs3E3ConfigLineIndex corresponds to Wellfleet circuit number
           wfDs3E3ConfigDelete 1.3.6.1.4.1.18.3.4.26.10.1.1 integer read-write
Create/Delete parameter Enumeration: 'deleted': 2, 'created': 1.
           wfDs3E3ConfigDisable 1.3.6.1.4.1.18.3.4.26.10.1.2 integer read-write
Enable/Disable parameter Enumeration: 'disabled': 2, 'enabled': 1.
           wfDs3E3ConfigState 1.3.6.1.4.1.18.3.4.26.10.1.3 integer read-only
State of the DS3 Port. Enumeration: 'lof': 4, 'raif': 5, 'loopback': 7, 'up': 1, 'ais': 6, 'down': 2, 'los': 3, 'notpresent': 20.
           wfDs3E3ConfigLastChange 1.3.6.1.4.1.18.3.4.26.10.1.4 timeticks read-only
The value of sysUpTime at the time the interface entered its current operational state.
           wfDs3E3ConfigLineIndex 1.3.6.1.4.1.18.3.4.26.10.1.5 integer read-only
this corresponds to the Wellfleet circuit number
           wfDs3E3ConfigIfIndex 1.3.6.1.4.1.18.3.4.26.10.1.6 integer read-only
this is value of ifIndex from the Interfaces table of MIB II (RFC 1213).
           wfDs3E3ConfigLineType 1.3.6.1.4.1.18.3.4.26.10.1.7 integer read-write
the variety of DS3/E3 application implementing this circuit Enumeration: 'ds3m23': 2, 'ds3cbitparity': 4, 'e3other': 6, 'ds3clearchannel': 5, 'autodetect': 9, 'e3framed': 7, 'ds3other': 1, 'ds3syntran': 3, 'e3plcp': 8.
           wfDs3E3ConfigLineCoding 1.3.6.1.4.1.18.3.4.26.10.1.8 integer read-write
the variety of Zero Code Suppression used on the link Enumeration: 'b3zs': 2, 'other': 1, 'hdb3': 3.
           wfDs3E3ConfigLoopbackConfig 1.3.6.1.4.1.18.3.4.26.10.1.9 integer read-write
the loopback configuration of the DS3/E3 interface Enumeration: 'lineloop': 3, 'noloop': 1, 'payloadloop': 2.
           wfDs3E3ConfigLineStatus 1.3.6.1.4.1.18.3.4.26.10.1.10 integer read-only
the status of the DS3/E3 line Enumeration: 'lof': 32, 'otherfailure': 512, 'loopback': 128, 'rctestcode': 256, 'noalarm': 1, 'rcais': 8, 'los': 64, 'txais': 16, 'txrai': 4, 'rcrai': 2.
           wfDs3E3ConfigPrimaryClockSource 1.3.6.1.4.1.18.3.4.26.10.1.11 integer read-write
Selects the Primary source of the Tx Clock for the DS3/E3 interface Enumeration: 'internal': 1, 'external': 2, 'loop': 3.
           wfDs3E3ConfigSecondaryClockSource 1.3.6.1.4.1.18.3.4.26.10.1.12 integer read-write
Selects the Secondary source of the Tx Clock for the DS3/E3 interface Enumeration: 'internal': 1, 'external': 2, 'loop': 3.
           wfDs3E3ConfigMtu 1.3.6.1.4.1.18.3.4.26.10.1.13 integer read-write
MTU parameter for all channels on DS3 .
           wfDs3E3ConfigLineBuildOut 1.3.6.1.4.1.18.3.4.26.10.1.14 integer read-write
Set according to cable length, short (less than 225 feet) or long (greater than 225 feet). Enumeration: 'short': 2, 'long': 1.
           wfDs3E3ConfigCurrentClock 1.3.6.1.4.1.18.3.4.26.10.1.15 integer read-only
Indicates the clock source currently in use by the DS1 Enumeration: 'internal': 1, 'external': 2, 'loop': 3.
           wfDs3E3ConfigExtClockOperational 1.3.6.1.4.1.18.3.4.26.10.1.16 integer read-only
Indicates whether the External clock is operational Enumeration: 'notpresent': 2, 'present': 1.
           wfDs3E3ConfigSetupAlarmThreshold 1.3.6.1.4.1.18.3.4.26.10.1.17 integer read-write
Specifies setup time for performance failure conditions, in seconds. When a performance defect is present for greater than the time specified by this parameter a performance failure is registered and a message is logged.
           wfDs3E3ConfigClearAlarmThreshold 1.3.6.1.4.1.18.3.4.26.10.1.18 integer read-write
Specifies clear time for performance failure conditions, in seconds. When a performance failure condition has been cleared for greater than the time specified by this parameter then the failure cleared condition is registered and a message is logged.
           wfDs3E3ConfigLoopbackState 1.3.6.1.4.1.18.3.4.26.10.1.19 integer read-only
Indicates the current loopback state of this interface. The interface can be in one the following states: Line Loopback Payload Loopback no loopback Loopback modes can be initiated by either of two methods: Manager requested Loopback is initiated by the Manager of this device. Network requested Loopback is initiated by this interface receiving an in-band request on the network from the far end device. Enumeration: 'mgrreqlineloop': 2, 'noloop': 1, 'netreqpayloadloop': 5, 'netreqlineloop': 4, 'mgrreqpayloadloop': 3.
           wfDs3E3ConfigSendCode 1.3.6.1.4.1.18.3.4.26.10.1.20 integer read-only
This variable is currently read-only and it indicates what type of code has been sent across the DS3 interface by the device. The values mean: SENDNOCODE - sending looped or normal data SENDLINECODE - sending a request for a line loopback SENDPAYLOADCODE - sending a request for a payload loopback SENDDS1LOOPCODE - sending a request for a DS1 loopback Enumeration: 'sendds1loopcode': 4, 'sendpayloadcode': 3, 'sendnocode': 1, 'sendlinecode': 2.
 wfDs3E3ActionTable 1.3.6.1.4.1.18.3.4.26.17 no-access
DS3E3 configuration Action record - write only Configuration parameters
       wfDs3E3ActionEntry 1.3.6.1.4.1.18.3.4.26.17.1 no-access
An entry in the DS3E3 Config table
           wfDs3E3ActionPortLineNumber 1.3.6.1.4.1.18.3.4.26.17.1.1 integer read-only
Instance ID LineNumber, filled in by driver
           wfDs3E3ActionSendFeacLoopCode 1.3.6.1.4.1.18.3.4.26.17.1.2 integer read-write
Selects a Far End Alarm and Control Channel code to be sent to the remote end. Enumeration: 'lineloop': 1, 'deactivatepl': 4, 'noaction': 21, 'deactivatell': 2, 'payloadloop': 3.
           wfDs3E3ActionSendFeacDs1LoopUpCode 1.3.6.1.4.1.18.3.4.26.17.1.3 integer read-write
Selects Loop Up code to be sent to the remote end for a DS1. Value passed through this attribute is the DS1 Port number (1 through 28). Enumeration: 'noaction': 29.
           wfDs3E3ActionSendFeacDs1LoopDownCode 1.3.6.1.4.1.18.3.4.26.17.1.4 integer read-write
Selects Loop Down code to be sent to the remote end for a DS1. Value passed through this attribute is the DS1 Port number (1 through 28). Enumeration: 'noaction': 29.
           wfDs3E3ActionClearCurrentStats 1.3.6.1.4.1.18.3.4.26.17.1.5 integer read-write
Clears this port's Current 15 minute Statistics. Enumeration: 'clrStats': 1, 'noaction': 2.
           wfDs3E3ActionClearFarEndCurrentStats 1.3.6.1.4.1.18.3.4.26.17.1.6 integer read-write
Clears this port's Far End, Current 15 minute Statistics. Enumeration: 'clrStats': 1, 'noaction': 2.
           wfDs3E3ActionClearDayCurrentStats 1.3.6.1.4.1.18.3.4.26.17.1.7 integer read-write
Clears this port's Current Day Statistics. Enumeration: 'clrStats': 1, 'noaction': 2.
           wfDs3E3ActionClearFarEndDayCurrentStats 1.3.6.1.4.1.18.3.4.26.17.1.8 integer read-write
Clears this port's Far End, Current Day Statistics. Enumeration: 'clrStats': 1, 'noaction': 2.
           wfDs3E3ActionClearIntervalStats 1.3.6.1.4.1.18.3.4.26.17.1.9 integer read-write
Clears All Interval Statistics (15 minute and day) of this port. Enumeration: 'clrStats': 1, 'noaction': 2.
           wfDs3E3ActionClearFarEndIntervalStats 1.3.6.1.4.1.18.3.4.26.17.1.10 integer read-write
Clears All Far End Interval Statistics (15 minute and day) of this port. Enumeration: 'clrStats': 1, 'noaction': 2.