UDS1-MIB: View SNMP OID List / Download MIB

VENDOR: UTSTARCOM INCORPORATED


 Home MIB: UDS1-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 usr 1.3.6.1.4.1.429
         nas 1.3.6.1.4.1.429.1
             uds1 1.3.6.1.4.1.429.1.4
                 uds1ConfigTable 1.3.6.1.4.1.429.1.4.1 no-access
This table is an extension of the ds1ConfigTable in the DS1 MIB defined by RFC1232.
                     uds1ConfigEntry 1.3.6.1.4.1.429.1.4.1.1 no-access
This table contains configurable parameters for a CSU that are not supported in the DS1 MIB defined by RFC1232. Each entry in this table corresponds to an entry in the DS1 MIB. There is a one-to-one correspondance between the value of uds1CSUIndex and ds1CSUIndex.
                         uds1CfgIndex 1.3.6.1.4.1.429.1.4.1.1.1 integer read-only
The index value which uniquely identifies the CSU to which this entry is applicable. The value corresponds to ds1CSUIndex in the DS1 MIB defined in RFC1232. The value of uds1CfgIndex matches the value of the index for the corresponding DS1 entity in the entity table of the chassis MIB.
                         uds1CfgRespToRemoteLoopbk 1.3.6.1.4.1.429.1.4.1.1.2 integer read-write
This object configures the specified CSU to either ignore or respond to remotely initiated loopback requests. Enumeration: 'ignore': 1, 'respond': 2.
                         uds1CfgJitterAttenuation 1.3.6.1.4.1.429.1.4.1.1.3 integer read-write
This object is used to select how the jitter attenuation circuit on the CSU is to be used. It can be used to attenuate jitter on the receiver, or the transmitter. Enumeration: 'attenJitterOnRcvr': 1, 'attenJitterOnTxmtr': 2, 'notApplicable': 3.
                         uds1CfgXmitLineBuildOut 1.3.6.1.4.1.429.1.4.1.1.4 integer read-write
This object is used to configure the amount of attenuation that is to be applied to the transmit signal in order to control cross-talk, etc. Enumeration: 'dB15': 3, 'dB0': 1, 'dB22': 4, 'dB7': 2, 'notApplicable': 5.
                         uds1CfgAutoBusyEnable 1.3.6.1.4.1.429.1.4.1.1.5 integer read-write
This object is used to enable or disable the automatic busy out feature for all timeslots on the specified CSU. If enabled, when a modem is considered idle and that modem is not sending the idle pattern to the T1 Card on the TDM bus, the timeslot will be busied out. Enumeration: 'disabled': 1, 'enabled': 2.
                         uds1CfgDialInAdr 1.3.6.1.4.1.429.1.4.1.1.6 integer read-write
This object identifies whether or not DNIS digits will be transferred as part of the call setup for the specified T1 line. Enumeration: 'ani-dnis': 3, 'dnis': 2, 'ani': 4, 'noAddress': 1.
                         uds1CfgZeroCoding 1.3.6.1.4.1.429.1.4.1.1.7 integer read-write
This object defines the type of zero coding used on the specified DS1. It provides some values that are not present in the experimental DS1 MIB. Enumeration: 'b8zs': 3, 'ami': 4, 'other': 1, 'hdb3': 5, 'zcs': 2.
                         uds1CfgDialInOutTrunkSt 1.3.6.1.4.1.429.1.4.1.1.8 integer read-write
This will set the Dial-in/Dial-out trunk start signal type. Default = wink(1). Enumeration: 'wink': 1, 'dialTone': 3, 'immediate': 2.
                         uds1CfgDialInAdrAckWinkEn 1.3.6.1.4.1.429.1.4.1.1.9 integer read-write
Allows to enable/disable an acknowledgement wink after the dial-in address information has been received. Enumeration: 'disabled': 1, 'enabled': 2.
                         uds1CfgDialOutAdrDly 1.3.6.1.4.1.429.1.4.1.1.10 integer read-write
Allows an adjustable delay on sending out address information from the T1 NAC to the TELCO.
                         uds1CfgStuffByteValue 1.3.6.1.4.1.429.1.4.1.1.11 integer read-write
The stuffed byte to send to TELCO for inactive DS0 in Fractional T1.
                         uds1CfgDialInOutTrunkType 1.3.6.1.4.1.429.1.4.1.1.12 integer read-write
This will set the Dial-In/Dial-out trunk type. Default = eAndMTypeII(1). Enumeration: 'eAndMTypeII': 1, 'groundStart': 3, 'loopStart': 2.
                         uds1CfgPriSwitchType 1.3.6.1.4.1.429.1.4.1.1.13 integer read-write
This sets the primary switch type for the T1-PRI ISDN NAC. The setting takes effect at NAC boot time. Default = priSw5ESS(2). Enumeration: 'priSwICTR4': 4, 'priSw5ESS': 2, 'priSwDMS100': 3, 'priSwVn4': 5, 'priSwNI2': 6, 'priSwDASS2': 8, 'priSw4ESS': 1, 'priSwINS1500': 7, 'priSwTSO14': 9.
                         uds1CfgIdleByte 1.3.6.1.4.1.429.1.4.1.1.14 integer read-write
This sets the idle byte pattern for the T1-PRI ISDN NAC. The setting takes effect at NAC boot time. Default = 0xFE.
                         uds1CfgAnlgBlockErrCode 1.3.6.1.4.1.429.1.4.1.1.15 integer read-write
This is the error code that will be returned to an ISDN switch when analog connections are being blocked. Default = 58.
                         uds1CfgDgtlBlockErrCode 1.3.6.1.4.1.429.1.4.1.1.16 integer read-write
This is the error code that will be returned to an ISDN switch when digital connections are being blocked. Default = 58.
                         uds1CfgNoMdmAvailErrCode 1.3.6.1.4.1.429.1.4.1.1.17 integer read-write
This is the error code that will be returned to an ISDN switch when there are no modems available to accept the requested connection. Default = 58.
                         uds1CfgNoIgwsAvailErrCode 1.3.6.1.4.1.429.1.4.1.1.18 integer read-write
This is the error code that will be returned to an ISDN switch when no IGWS connections are available. Default = 58.
                         uds1CfgChanBlockErrCode 1.3.6.1.4.1.429.1.4.1.1.19 integer read-write
This is the error code that will be returned to an ISDN switch when connections to a specific B channel are being blocked. Default = 58.
                         uds1CfgBlockCallType 1.3.6.1.4.1.429.1.4.1.1.20 integer read-write
This object determines if a PRI span line will block calls of a specific type. This object does not apply to a NAC operating in Rob Bit T1 mode. Default = blockNone(2). Enumeration: 'blockAll': 5, 'blockAnalog': 3, 'notSupported': 1, 'blockNone': 2, 'blockDigital': 4.
                         uds1CfgNfasId 1.3.6.1.4.1.429.1.4.1.1.21 integer read-write
This defines the NFAS ID associated with a PRI span line. This object does not apply to Rob Bit T1 operation. Default = 0.
                         uds1CfgNfasDChannel 1.3.6.1.4.1.429.1.4.1.1.22 integer read-write
This determines how a PRI span line will use the DS0 normally assigned as a D channel when NFAS is being used. This object does not apply to Rob Bit T1 operation. Default = dchannel(2). Enumeration: 'extraBchannel': 3, 'notSupported': 1, 'dchannel': 2.
                         uds1CfgShrtHaulDist 1.3.6.1.4.1.429.1.4.1.1.23 integer read-write
Variuos distance ranges supported by Short Haul NIC Default=len0thru133Ft. Enumeration: 'len0thru133Ft': 2, 'len533thru655Ft': 6, 'len133thru266Ft': 3, 'len266thru399Ft': 4, 'notApplicable': 1, 'len399thru533Ft': 5.
                         uds1CfgCallProceedingRsp 1.3.6.1.4.1.429.1.4.1.1.24 integer read-write
This object determines to send CALL_PROCEEDING and CONNECT response, when a SETUP message is received from TELCO. Default = ON. Enumeration: 'on': 2, 'off': 1.
                         uds1CfgAlertingRsp 1.3.6.1.4.1.429.1.4.1.1.25 integer read-write
This object determines to send ALERTING response, when a SETUP message is received from TELCO. Default = OFF. Enumeration: 'on': 2, 'off': 1.
                         uds1CfgServiceState 1.3.6.1.4.1.429.1.4.1.1.26 integer read-write
This objects configures the service state of the DS1 and will configure the state for power up if saved to NVRAM. Default= inService(2). Enumeration: 'localOutOfService': 3, 'notSupported': 1, 'inService': 2.
                         uds1CfgIcbKeyword 1.3.6.1.4.1.429.1.4.1.1.27 displaystring read-write
This is the keyword used for DASS2 Incoming Call Barring control.
                         uds1CfgOverlapRxMode 1.3.6.1.4.1.429.1.4.1.1.28 integer read-write
This object allows dialed digits to arrive in separate messages. Default = disabled(2) Enumeration: 'enable': 1, 'disable': 2.
                         uds1CfgEandMnoAddrTimer 1.3.6.1.4.1.429.1.4.1.1.29 integer read-write
This object is for E&M type II trunks with no DNIS address. If timer is >0, the ch T1 NAC will flush calls upon timer expiration, if the modem has not signalled the NAC to go ahead and answer the call. 2 seconds per unit. Default = 0
                         uds1CfgSeizureWinkDly 1.3.6.1.4.1.429.1.4.1.1.30 integer read-write
Allows an adjustable delay on sending out address information from the T1 NAC to the TELCO. Default=18.
                 uds1IntervalTable 1.3.6.1.4.1.429.1.4.2 no-access
An extension of the DS1 Interval table which provides status counters over 15 minute intervals.
                     uds1IntervalEntry 1.3.6.1.4.1.429.1.4.2.1 no-access
An entry in the extended DS1 Interval table. Every entry in the DS1 Interval table will have a corresponding entry in this table.
                         uds1IntIndex 1.3.6.1.4.1.429.1.4.2.1.1 integer read-only
This is the index value which uniquely identifies the CSU to which this entry is applicable. The value of uds1IntIndex matches the value of the index for the corresponding DS1 entity in the entity table of the chassis MIB.
                         uds1IntNumber 1.3.6.1.4.1.429.1.4.2.1.2 integer read-only
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minute interval (assuming that all 96 intervals are valid).
                         uds1IntBurstyErrSeconds 1.3.6.1.4.1.429.1.4.2.1.3 counter read-only
This object counts the number of seconds, over the specified interval, in which there were more than 2 and less than 320 CRC errors.
                         uds1IntFrameBitErrors 1.3.6.1.4.1.429.1.4.2.1.4 counter read-only
A specific bit pattern is used for the T1 receiver to determine frame allignment. This object counts the number of incorrectly received framing bits in the specified 15 minute interval.
                         uds1IntDeltaFrameAlligns 1.3.6.1.4.1.429.1.4.2.1.5 counter read-only
This object counts the number of times the specified T1 receiver has reframed on a new framing pattern (ie. due to an OOF condition) in the specified 15 minute interval.
                         uds1IntExcessCRCErrors 1.3.6.1.4.1.429.1.4.2.1.6 counter read-only
This object counts each time 32 of any 33 consecutive CRCs are in error for the specified T1 line in the specified 15 minute interval. This counter is only valid in ESF format.
                 uds1CurrentTable 1.3.6.1.4.1.429.1.4.3 no-access
An extension of the DS1 Current table that provides status counters over the present 15 minute interval.
                     uds1CurrentEntry 1.3.6.1.4.1.429.1.4.3.1 no-access
An entry in the extended DS1 Current table. Every entry in the DS1 Current table will have a corresponding entry in this table.
                         uds1CurrIndex 1.3.6.1.4.1.429.1.4.3.1.1 integer read-only
The index value which uniquely identifies the CSU to which this entry is applicable. The value of uds1CurrIndex matches the value of the index for the corresponding DS1 entity in the entity table of the chassis MIB.
                         uds1CurrBurstyErrSeconds 1.3.6.1.4.1.429.1.4.3.1.2 counter read-only
This object counts the number of seconds, in the current 15 minute interval, during which there was more than two, and less than 320 CRC errors.
                         uds1CurrFrameBitErrors 1.3.6.1.4.1.429.1.4.3.1.3 counter read-only
A specific bit pattern is used for the receiver to determine frame allignment. This object is a count of the number of incorrectly received framing bits in the current 15 minute interval.
                         uds1CurrDeltaFrameAlligns 1.3.6.1.4.1.429.1.4.3.1.4 counter read-only
This object counts the number of times the specified T1 receiver has reframed on a new framing pattern (ie. due to an OOF condition) in the current 15 minute interval.
                         uds1CurrExcessCRCErrors 1.3.6.1.4.1.429.1.4.3.1.5 counter read-only
This object counts each time 32 of any 33 consecutive CRCs are in error for the specified T1 line in the current 15 minute interval. This counter is only valid in ESF format.
                 uds1TotalTable 1.3.6.1.4.1.429.1.4.4 no-access
An extension of the DS1 Total table that provides the cumulative sum of the various statistics for the 24 hour interval preceding the first valid interval in the uds1CurrentTable.
                     uds1TotalEntry 1.3.6.1.4.1.429.1.4.4.1 no-access
An entry in the extended DS1 Total table.
                         uds1TotIndex 1.3.6.1.4.1.429.1.4.4.1.1 integer read-only
The index value which uniquely identifies the CSU to which this entry is applicable. The value of ds1TotalIndex matches the value of the index for the corresponding DS1 entity in the entity table of the chassis MIB.
                         uds1TotBurstyErrSeconds 1.3.6.1.4.1.429.1.4.4.1.2 counter read-only
This object counts the number of seconds, over the last 24 hour period, in which there were more than 2 and less than 320 CRC errors.
                         uds1TotFrameBitErrors 1.3.6.1.4.1.429.1.4.4.1.3 counter read-only
A specific bit pattern is used so the T1 receiver can determine frame allignment. This object counts the total number of incorrectly received framing bits in the last 24 hour period.
                         uds1TotDeltaFrameAlligns 1.3.6.1.4.1.429.1.4.4.1.4 counter read-only
This object counts the number of times the specified T1 receiver has reframed on a new framing pattern (ie. due to an OOF condition) in the last 24 hour period.
                         uds1TotExcessCRCErrors 1.3.6.1.4.1.429.1.4.4.1.5 counter read-only
This object indicates the total number of times there have been 32 of any 33 consecutive CRCs in error on the specified T1 line in the last 24 hour period. This counter is only valid in ESF format.
                 uds1StatTable 1.3.6.1.4.1.429.1.4.5 no-access
USR's DS1 Status table contains various CSU status information. There is no corresponding table in the DS1 MIB defined by RFC1232.
                     uds1StatEntry 1.3.6.1.4.1.429.1.4.5.1 no-access
There is one entry in the DS1 Status table for each CSU in the chassis.
                         uds1StatIndex 1.3.6.1.4.1.429.1.4.5.1.1 integer read-only
The index value which uniquely identifies the CSU to which this entry is applicable. The value of this object matches the value of the index for the corresponding DS1 entity in the entity table of the chassis MIB.
                         uds1StatReceiverGain 1.3.6.1.4.1.429.1.4.5.1.2 integer read-only
This object identifies the amount of gain applied to boost the receive signal level to an appropriate operating level. Enumeration: 'dB15': 3, 'dB0': 1, 'dB22': 4, 'dB7': 2, 'notApplicable': 5.
                         uds1StatOutOfFrame 1.3.6.1.4.1.429.1.4.5.1.3 integer read-only
This object indicates when the framing pattern for the specified T1 line has been lost and data connot be extracted properly. This condition is also known as red alarm. Enumeration: 'true': 2, 'false': 1.
                         uds1StatLossOfSignal 1.3.6.1.4.1.429.1.4.5.1.4 integer read-only
This object indicates when 175 consecutive 0's have been detected. The signal is considered recovered if the 1's density reaches 12.5% (ie. four ones in a 32 bit period). Enumeration: 'true': 2, 'false': 1.
                         uds1StatReceivingAIS 1.3.6.1.4.1.429.1.4.5.1.5 integer read-only
This object identifies when the remote end of the specified T1 line has lost its receive signal and is transmitting a stream of all 1's to the local end. This AIS condition is also known as blue alarm. Enumeration: 'true': 2, 'false': 1.
                         uds1StatSwitchTypeActive 1.3.6.1.4.1.429.1.4.5.1.6 integer read-only
This object identifies the primary switch type that the T1-PRI ISDN NAC is currently connected to. Enumeration: 'priSwICTR4': 4, 'priSw5ESS': 2, 'priSwDMS100': 3, 'priSwVn4': 5, 'priSwNI2': 6, 'priSwDASS2': 8, 'priSw4ESS': 1, 'priSwINS1500': 7, 'priSwTSO14': 9.
                         uds1StatDchanOperational 1.3.6.1.4.1.429.1.4.5.1.7 integer read-only
This object reflects the operational status of the D channel on the T1-PRI ISDN NAC. Enumeration: 'bChannel': 3, 'dChannelUp': 1, 'dChannelDown': 2.
                         uds1StatE1ContCrc 1.3.6.1.4.1.429.1.4.5.1.8 integer read-only
This object indicates when continuous CRC errors are being received on the E1 DS1 span line on the T1-PRI ISDN NAC. Enumeration: 'true': 2, 'false': 1.
                         uds1StatE1PhysicalState 1.3.6.1.4.1.429.1.4.5.1.9 integer read-only
This object reflects the physical state of the E1 DS1 span line on the T1-PRI ISDN NAC. Enumeration: 'psF1Operational': 1, 'psF3Fc2LossOfSignal': 3, 'psF6PowerOn': 6, 'psF2Fc1RaiTempCrcErrors': 2, 'psF5Fc4RaiContCrcErrors': 5, 'psF4Fc3AlarmIndSignal': 4.
                         uds1StatLoopBackInit 1.3.6.1.4.1.429.1.4.5.1.10 integer read-only
This object tells if the loopback was initiated by the network or by command Enumeration: 'none': 1, 'command': 3, 'network': 2.
                         uds1StatNfasDChannel 1.3.6.1.4.1.429.1.4.5.1.11 integer read-only
This reflect how a PRI span line is using the DS0 normally assigned as a D channel when NFAS is being used. This object does not apply to Rob Bit T1 operation. Default = dchannel(2). Enumeration: 'extraBchannel': 3, 'notSupported': 1, 'dchannel': 2.
                         uds1StatDChannel 1.3.6.1.4.1.429.1.4.5.1.12 integer read-only
This is the status of the D channel for this PRI span line. A value of notSupported(1) means that this DS1 is not operating in ISDN mode or there is no D channel defined on this span line. Enumeration: 'notSupported': 1, 'bChannel': 3, 'inService': 2.
                         uds1StatDs0SrvcChngLst 1.3.6.1.4.1.429.1.4.5.1.13 displaystring read-only
This object contains the current list of DS0s that have changed their state from In Service to Out of Service or Vice versa. The list is included in the corresponding SNMP trap.
                         uds1StatMultiFrame 1.3.6.1.4.1.429.1.4.5.1.14 integer read-only
This object identifies when the E1/PRI NAC line has lost synchronization with the Time-Slot 16 Multi-Frame alignment pattern. Only valid for E1/CAS NAC. Enumeration: 'true': 2, 'false': 1.
                         uds1StatRemMultiFrame 1.3.6.1.4.1.429.1.4.5.1.15 integer read-only
This object identifies when the remote end of the specified E1/PRI NAC line has lost synchronization with the Time-Slot 16 Multi-Frame alignment pattern. Only valid for E1/CAS NAC. Enumeration: 'true': 2, 'false': 1.
                         uds1StatServiceState 1.3.6.1.4.1.429.1.4.5.1.16 integer read-only
This object shows the current state of the DS1 Service. Default = inService(2). Enumeration: 'localOutOfService': 3, 'notSupported': 1, 'inService': 2.
                 uds1CmdTable 1.3.6.1.4.1.429.1.4.6 no-access
The DS1 Command table contains an entry for each of the manageable CSUs in the chassis. It provides a means through which to take specific actions on one or more CSUs in the chassis.
                     uds1CmdEntry 1.3.6.1.4.1.429.1.4.6.1 no-access
There is one entry in the DS1 Command table per CSU in the chassis.
                         uds1CmdIndex 1.3.6.1.4.1.429.1.4.6.1.1 integer read-only
A unique value for each CSU in the chassis. The value of uds1CmdIndex matches the value of the index for the corresponding DS1 entity in the entity table of the chassis MIB.
                         uds1CmdMgtStationId 1.3.6.1.4.1.429.1.4.6.1.2 octet string read-write
This object is a generic read-write variable that a Management Station (MS) can use to guarantee that the results from a given command are the result of that specific MS. Each MS must SET a unique value to this object when doing commands and GET the value of this object together with uds1CmdReqId and uds1CmdResult to detect interference from other MSs.
                         uds1CmdReqId 1.3.6.1.4.1.429.1.4.6.1.3 integer read-only
This object contains the value of the request-id field in the SNMP PDU which invoked the current or most recent command on this DS1 interface. If the request-id is unknown or undefined, this object contains the zero value.
                         uds1CmdFunction 1.3.6.1.4.1.429.1.4.6.1.4 integer read-write
This object identifies the command being requested. Enumeration: 'localOutOfService': 6, 'blockAnalogCalls': 7, 'bringUpDChannel': 13, 'blockAllCalls': 9, 'takeDownDChannel': 12, 'noCommand': 1, 'enterLoopback': 3, 'exitLoopback': 4, 'forceReceiverReframe': 2, 'blockNoCalls': 10, 'redAlarmOverride': 11, 'blockDigitalCalls': 8, 'inService': 5.
                         uds1CmdForce 1.3.6.1.4.1.429.1.4.6.1.5 integer read-write
In some cases, the DS1 interface may be in a state such that certain commands could adversely affect connections. In such cases, a command request with uds1CmdForce not defined, or set to noForce will result in a warning. If the operator elects to ignore such warnings, uds1CmdForce can be set to force in a re-issued request and the command will be carried out regardless of its potentially hazzardous effects. Enumeration: 'noForce': 2, 'force': 1.
                         uds1CmdParam 1.3.6.1.4.1.429.1.4.6.1.6 octet string read-write
This object contains parameters that are specific to the particular command being issued. In some cases, there will be no additional parameters required.
                         uds1CmdResult 1.3.6.1.4.1.429.1.4.6.1.7 integer read-only
This object contains the result of the most recently requested command, or the value none(1) if no commands have been requested since the last reset. Enumeration: 'none': 1, 'success': 2, 'failed': 7, 'unAbleToRun': 5, 'aborted': 6, 'inProgress': 3, 'notSupported': 4.
                         uds1CmdCode 1.3.6.1.4.1.429.1.4.6.1.8 integer read-only
The value of this object upon command completion indicates a further description of what went wrong if the command was unsuccessful. Enumeration: 'pendingSoftwareDownload': 73, 'unsupportedCommand': 20, 'deviceDisabled': 22, 'unrecognizedCommand': 6, 'noError': 1, 'unable': 2, 'slotEmpty': 8, 'noResponse': 12.
                 uds1TrapEnaTable 1.3.6.1.4.1.429.1.4.7 no-access
A trap enable table that defines a column for every trap that a DS1 entity can generate.
                     uds1TrapEnaEntry 1.3.6.1.4.1.429.1.4.7.1 no-access
There is one entry in this table for every CSU that exists in the chassis.
                         uds1TrapEnaIndex 1.3.6.1.4.1.429.1.4.7.1.1 integer read-only
A unique value for each CSU in the chassis. The value of uds1TrapEnaIndex matches the value of the index for the corresponding DS1 entity in the entity table of the chassis MIB.
                         uds1TrapEnaYellowAlarm 1.3.6.1.4.1.429.1.4.7.1.2 integer read-write
Enable the generation of an SNMP trap upon detection of a yellow alarm condition on the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaRedAlarm 1.3.6.1.4.1.429.1.4.7.1.3 integer read-write
Enable the generation of an SNMP trap upon detection of a red alarm condition on the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaLossOfSignal 1.3.6.1.4.1.429.1.4.7.1.4 integer read-write
Enable the generation of an SNMP trap upon detection of loss of signal on the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaAlarmIndSignal 1.3.6.1.4.1.429.1.4.7.1.5 integer read-write
Enable the generation of an SNMP trap upon detection of an alarm indication signal (AIS) on the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaYellowAlarmClr 1.3.6.1.4.1.429.1.4.7.1.6 integer read-write
Enable the generation of an SNMP trap upon detection of a yellow alarm condition being cleared on the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaRedAlarmClr 1.3.6.1.4.1.429.1.4.7.1.7 integer read-write
Enable the generation of an SNMP trap upon detection of a red alarm condition being cleared on the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaLossOfSgnlClr 1.3.6.1.4.1.429.1.4.7.1.8 integer read-write
Enable the generation of an SNMP trap upon detection of loss of signal condition being cleared on the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaAlrmIndSgnlClr 1.3.6.1.4.1.429.1.4.7.1.9 integer read-write
Enable the generation of an SNMP trap upon detection of an alarm indication signal (AIS) being cleared on the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaContCrcAlrm 1.3.6.1.4.1.429.1.4.7.1.10 integer read-write
Enable the generation of an SNMP trap upon detection of a continuous CRC condition on the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaContCrcAlrmClr 1.3.6.1.4.1.429.1.4.7.1.11 integer read-write
Enable the generation of an SNMP trap upon detection of the clearing of a continuous CRC condition on the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaPhysStateChng 1.3.6.1.4.1.429.1.4.7.1.12 integer read-write
Enable the generation of an SNMP trap upon detection of a change in the physical state of the specified DS1. Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaDchanInSrvc 1.3.6.1.4.1.429.1.4.7.1.13 integer read-write
Enable the generation of an SNMP trap upon detection of a change in the service state of a D channel on this span line from Out of Service, Maintenance or Standby to In Service. Default = disableAll(2). Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaDchanOutOfSrvc 1.3.6.1.4.1.429.1.4.7.1.14 integer read-write
Enable the generation of an SNMP trap upon detection of a change in the service state of a D channel on this span line from In Service to Out of Service, Maintenance or Standby. Default = disableAll(2). Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaDs0InSrvc 1.3.6.1.4.1.429.1.4.7.1.15 integer read-write
Enable the generation of an SNMP trap upon detection of a change in the service state of a DS0 on this span line from Out of Service to In Service. Default = disableAll(2). Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaDs0OutOfSrvc 1.3.6.1.4.1.429.1.4.7.1.16 integer read-write
Enable the generation of an SNMP trap upon detection of a change in the service state of a DS0 on this span line from In Service to Out of Service. Default = disableAll(2). Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaMultiFrame 1.3.6.1.4.1.429.1.4.7.1.17 integer read-write
Enable the generation of an SNMP trap upon detection of a Multi-Frame Alignment condition on the specified DS1. Default = disableAll(2). Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaRemMultiFrame 1.3.6.1.4.1.429.1.4.7.1.18 integer read-write
Enable the generation of an SNMP trap upon detection of a Remote Multi-Frame Alignment condition on the specified DS1. Default = disableAll(2). Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaMultiFrmClr 1.3.6.1.4.1.429.1.4.7.1.19 integer read-write
Enable the generation of an SNMP trap upon detection of clearing a Multi-Frame Alignment condition on the specified DS1. Default = disableAll(2). Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.
                         uds1TrapEnaRemMultiFrmClr 1.3.6.1.4.1.429.1.4.7.1.20 integer read-write
Enable the generation of an SNMP trap upon detection of clearing a Remote Multi-Frame Alignment condition on the specified DS1. Default = disableAll(2). Enumeration: 'enableTrap': 1, 'enableAll': 4, 'enableLog': 3, 'disableAll': 2.