TIMETRA-SAP-MIB: View SNMP OID List / Download MIB

The current number of SAPs configured in this device.

A table that contains basic SAP information.

Information about a specific SAP.

The ID of the access port where this SAP is defined.

The value of the label used to identify this SAP on the access port specified by sapPortId.

This object indicates the status of this row. The only values supported during a set operation are createAndGo and destroy.

This object indicates the type of service where this SAP is defined.

Generic information about this SAP.

The desired state of this SAP.

The value of the object sapOperStatus indicates the operating state of this SAP.

The value of the object sapIngressQosPolicyId specifies the row index in the tSapIngressTable corresponding to this ingress QoS policy, or one if no policy is specified. The value 0 is needed for mirror SAPs that cannot have a QoS policy assigned.

The value of the object sapIngressMacFilterId specifies the row index in the tMacFilterTable corresponding to this ingress filter, or zero if no filter is specified.

The value of the object sapIngressIpFilterId specifies the row index in the tIPFilterTable corresponding to this ingress filter, or zero if no filter is specified.

The row index in the tSapEgressTable corresponding to this egress QoS policy, or one if no policy is specified.

The row index in the tMacFilterTable corresponding to this egress filter, or zero if no filter is specified.

The row index in the tIPFilterTable corresponding to this egress filter, or zero if no filter is specified.

This object specifies whether traffic mirroring has been enabled on this SAP.

When the value of sapType is ies this object specifies the index of the IES interface where this SAP is defined. The value of this object can be set only when the row is created and cannot be changed while the row status is active. This object is otherwise not significant and should have the value zero.

The value of sysUpTime at the time of the most recent management-initiated change to this SAP.

When the value of this object is true the agent collects accounting statistics on this SAP.

This object specifies the policy to use to collect accounting statistics on this SAP. The value zero indicates that the agent should use the default accounting policy, if one exists.

The VPN ID of the associated service.

The Customer ID of the associated service.

The value of this object, when not null, indicates the Multi-Service Site this SAP is a member of. This information is used to configure the ingress and egress QoS schedulers for this SAP.

This object can be set only when sapCustMultSvcSite is null. It indicates the ingress QoS scheduler for this SAP.

This object can be set only when sapCustMultSvcSite is null. It indicates the egress QoS scheduler for this SAP.

This object specifies the name of the split-horizon group where the SAP belongs to. This object can be set only at the time the row is created. Per default a SAP does not belong to any split-horizon group. The name specified must correspond to an existing split- horizon group in the TLS service where this SAP is defined.

This object indicates the ingress shared queue policy used by this SAP. When the value of this object is null it means that the SAP will use individual ingress QoS queues, instead of the shared ones.

This object applies only to SAPs defined on a port configured for qinq service encapsulation. It indicates which 802.1P bits will be used to match a QoS or a MAC filter policy when a double-tagged frame is received on this SAP.

This object specifies all the conditions that affect the operating status of this SAP. The bit values are: sapAdminDown (0) - SAP is admin down. svcAdminDown (1) - Service is admin down. iesIfAdminDown (2) - IP interface is admin down (IES and VPRN only). portOperDown (3) - Access port is oper down. portMtuTooSmall (4) - Access ports MTU is < Service MTU l2OperDown (5) - L2 PVC/PVP is oper down (FR and ATM only). ingressQosMismatch (6) - Mismatch between ingress QoS and Scheduler policies. egressQosMismatch (7) - Mismatch between egress QoS and Scheduler policies. relearnLimitExceeded (8) - MAC relearn limit was exceeded (TLS only). recProtSrcMac (9) - Received a packet with a protected source MAC (TLS only). subIfAdminDown (10) - Subscriber interface is admin down (group-interface SAP only). sapIpipeNoCeIpAddr (11) - CE IP Address not configured for Ipipe SAP (IPIPE SAP only). sapTodResourceUnavail (12) - SAP with ToD had insufficient resources at boot time and got default policies. sapTodMssResourceUnavail (13) - MSS of this SAP uses ToD and due to insufficient resources at boot time got default scheduler policies. sapParamMismatch (14) - Service specific local parameter mismatch. sapCemNoEcidOrMacAddr (15) - ECID or MAC address not configured (CEM SAP only). sapStandbyForMcRing (16) - mc-ring keeps this SAP standby for the corresponding SAP on peer. sapSvcMtuTooSmall (17) - Service MTU is < SAP payload. ingressNamedPoolMismatch (18) - Invalid named-pool on the ingress side. egressNamedPoolMismatch (19) - Invalid named-pool on the egress side. ipMirrorNoMacAddr (20) - No MAC Address configured for the ip-mirror. sapEpipeNoRingNode (21) - No TIMETRA-MC-REDUNDANCY-MIB ::tmnxMcEpipeSapEntry object configured for Epipe SAP (EPIPE SAP only). mcStandby (22) - indicates the SAP is standby because of a mutli-chassis protocol. mhStandby (23) - indicates the SAP is standby because of a BGP multi-home protocol. oamDownMepFault (24) - ETH-CFM down MEP fault detected. oamUpMepFault (25) - ETH-CFM up MEP fault detected. ethTunTagMisconfig (26) - Missing Eth-tunnel SAP tag(s). ingressPolicerMismatch (27)- indicate ingress policer - is parented to non-existent arbiter egressPolicerMismatch (28) - indicate egress policer - is parented to non-existent arbiter. sapTlsNoRingNode (29) - No TIMETRA-MC-REDUNDANCY-MIB ::tmnxMcTlsSapEntry object configured for TLS SAP (VPLS SAP only). ethRingPathBlocked (30) - indicates eth-ring path is blocked. oamTunnelMepFault (31) - ETH-CFM Tunnel MEP fault detected. operGrpDown (32) - indicates operational-group is down.

The value of sysUpTime at the time of the most recent operating status change to this SAP.

The value of the object sapAntiSpoofing specifies the type of anti-spoof filtering applicable on this SAP. nextHopIpAndMacAddr (4) is not supported on SR-1, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is 5.

The value of the object sapIngressIpv6FilterId specifies the row index in the tIPv6FilterTable corresponding to this ingress ipv6 filter, or zero if no ipv6 filter is specified.

The value of the object sapEgressIpv6FilterId specifies the row index in the tIPv6FilterTable corresponding to this egress ipv6 filter, or zero if no ipv6 filter is specified.

The value of the object sapTodSuite specifies the Time of Day (ToD) suite to be applied on this SAP. An empty string indicates that no ToD suite is applied on this SAP. A set request will only be allowed, if the indicated suite is defined in TIMETRA-SCHEDULER-MIB::tmnxTodSuiteTable.

When the value of sapIngressSharedQueuePolicy is not null, the value of the object sapIngUseMultipointShared specifies whether this SAP uses the multipoint-shared queues of the shared policy.

When the encapsulation type of the access port where this SAP is defined is qinq, the value of the object sapEgressQinQMarkTopOnly specifies which P-bits to mark during packet egress. When the value is false both set of P-bits are marked. When the value is true, only the P-bits in the top Q-tag are marked.

The value of the object sapEgressAggRateLimit specifies the maximum total rate of all egress queues for this SAP. The value -1 means that there is no limit.

The value of the object sapEndPoint specifies the service endpoint to which this SAP is attached. The svcId of the SAP MUST match the svcId of the service endpoint.

The value of sapIngressVlanTranslation specifies the desired Ingress Vlan Translation. A value of vlanId specifies that the value of sapIngressVlanTranslationId is to be used to overwrite the preserved VLAN id in the packet. A value of copyOuter specifies that the outer VLAN id should be used to overwrite the preserved VLAN id in the packet. An inconsistentValue error is returned when an attempt is made to set the value of sapIngressVlanTranslation to vlanId and sapIngressVlanTranslationId is set to -1.

The value of sapIngressVlanTranslationId specifies the VLAN id to be used to overwrite the preserved VLAN id in the packet. An inconsistentValue error is returned when an attempt is made to set the value of sapIngressVlanTranslationId to other than -1 and sapIngressVlanTranslation is not set to vlanId.

The value of the object sapSubType indicates the sub-type for this SAP. A value of regular indicates a standard SAP. A value of capture specifies a capturing SAP in which triggering packets will be sent to the CPM. Non-triggering packets captured by the capture SAP will be dropped. A value of managed indicates a managed SAP which was created dynamically after receiving triggering packets on a SAP with a sapSubType value of capture. Entries with a value of managed are not user editable and are not maintained in the configuration file. A value of video indicates a video SAP which terminates on a video SAP. Entries with a value of video are not user editable and are not maintained in the configuration file. A value of internal indicates an internal SAP which was created by the system. Entries with a value of internal are not user editable and are not maintained in the configuration file. Whereas any of the five values may be returned in in response to an SNMP GET request, only two values may be specified in an SNMP SET request: regular and capture. An attempt to specify a value of managed, video or internal in an SNMP SET request will fail with an error of inconsistentValue. The value of this object cannot be changed after creation.

The value of sapCpmProtPolicyId associates a CPM Protection policy with a SAP. A value of zero (0) specifies that no CPM Protection policy is associated with this SAP. A value of 254 specifies that the default CPM Protection policy is associated with this SAP. If no value for sapCpmProtPolicyId is specified when the sapBaseInfoEntry is created, the system assigns a default value as follows: if the system creates a corresponding entry in the sapSubMgmtInfoTable, the default value is 254; otherwise, the default value is zero. This means that all SAPs that support Enhanced Subscriber Management get a default value of 254. If a SAP would get a default value of 254, it is not allowed to set the value of sapCpmProtPolicyId to zero. If a SAP would get a default value of zero, it is not allowed to modify the value of sapCpmProtPolicyId. This object is not supported on SR-1 and ESS-1, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is 5, and 7710, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is 7 or 9.

The value of sapCpmProtMonitorMac specifies whether or not to apply the tmnxCpmProtPolPerSrcRateLimit of this SAPs CPM Protection policy to packets served by the SAP, on a per source MAC address basis. For example, suppose sapCpmProtMonitorMac is true, and this SAPs sapCpmProtPolicyId points to a policy table row with tmnxCpmProtPolPerSrcRateLimit set to 100 packets/second. Suppose two source MAC addresses each send 150 packets/second to this SAP. Approx. 50 packets/second from each source will be discarded. If the value of sapCpmProtPolicyId is equal to zero, the value of sapCpmProtMonitorMac is irrelevant and will be ignored. At most one of the following options can be enabled on this SAP: 1. sapCpmProtMonitorMac, 2. The sapCpmProtEthCfmMonitorFlags option ethCfmMonitor(0), 3. sapCpmProtMonitorIP. This object is not supported on SR-1 and ESS-1, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is 5, and 7710, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is 7 or 9.

The value of sapEgressFrameBasedAccounting specifies whether to use frame-based accounting when evaluating sapEgressAggRateLimit for all egress queues for this SAP. If the value is false, the default packet-based accounting method will be used.

The value of the object sapIngressAggRateLimit specifies the maximum total rate of all ingress queues for this SAP. The value -1 means that there is no limit. This object is obsoleted in 10.0 Release.

The value of the object sapEgressHsmdaShaperOverride specifies the name of the secondary shaper for this SAP. The value must correspond to an entry in the tmnxPortEgrShaperTable. If the empty string is specified, the default secondary shaper will be used.

The value of sapIngressHsmdaPacketOffOvr specifies the value, in bytes, of the adjustment to make to the size of each packet for HSMDA queue accounting on ingress. This object is obsoleted in 10.0 Release.

The value of sapEgressHsmdaPacketOffOverride specifies the value, in bytes, of the adjustment to make to the size of each packet for HSMDA queue accounting on ingress.

The value of sapCallingStationId specifies the calling-station-id to be included in all RADIUS authentication and accounting requests if configured to be included in the corresponding RADIUS authentication or accounting policy. If the empty string is specified, no calling-station-id will be included.

The value of sapIsaAaApplicationProfile specifies the ISA-AA application profile for this sap. The specified application profile needs to exist in the TIMETRA-BSX-NG-MIB::tmnxBsxAppProfTable.

The value of sapIngPolicerPolicy specifies the ingress policer control policy applicable to this subscriber profile.

The value of sapEgrPolicerPolicy specifies the egress policer control policy applicable to this subscriber profile.

The value of sapTmplUsed indicates the name of the sap-template used to create this sap. A value of empty-string indicates that this sap was not created using a sap-template.

The value of sapEthRingIndex specifies the Ethernet Ring associated with this SAP. This object, if required, MUST be configured during the row creation of the sapBaseInfoTable row, and MUST reference an existing row in TIMETRA-ETH-RING-MIB::tmnxEthRingConfigTable. The value zero, the default value, specifies there is no Ethernet Ring associated with this SAP. This object can not be changed once set; the SAP MUST be destroyed and re-created to change the sapEthRingIndex object.

The value of sapIngressFlowspec specifies whether ingress Flowspec is enabled for this sap.

The value of sapCpmProtEthCfmMonitorFlags specifies whether or not to apply rate limiting (using the tmnxCpmProtEthCfmPolTable configuration) to Ethernet Connectivity Fault Management (Eth-CFM) packets served by the SAP. Two associated options are also specified. Five combinations of flag values are supported, as shown in the following table. Flag Value (0=Disabled, 1=Enabled) ------------------------------------- ----------------------------- ethCfmMonitor(0) 0 0 0 0 1 1 1 1 ethCfmMonitorAggregate(1) 0 0 1 1 0 0 1 1 ethCfmMonitorCommittedAccessRate(2) 0 1 0 1 0 1 0 1 ------------------------------------- ----------------------------- Supported Combination? Y N N N Y Y Y Y If ethCfmMonitor(0) is disabled, Eth-CFM rate limiting is disabled on this SAP. If ethCfmMonitor(0) is enabled, Eth-CFM rate limiting is enabled on this SAP. Excess packets are discarded. The configured information used to perform the Eth-CFM rate limiting (e.g. the rate limit(s)) resides in the tmnxCpmProtEthCfmPolTable row(s) indexed by the SAPs sapCpmProtPolicyId. At most one of the following options can be enabled on this SAP: 1. sapCpmProtMonitorMac, 2. The sapCpmProtEthCfmMonitorFlags option ethCfmMonitor(0), 3. sapCpmProtMonitorIP. The flags ethCfmMonitorAggregate(1) and ethCfmMonitorCommittedAccessRate(2) adjust the behavior of Eth-CFM rate limiting. Therefore, they are only significant if Eth-CFM rate limiting is enabled (i.e. when ethCfmMonitor(0) is enabled). The remainder of this DESCRIPTION assumes ethCfmMonitor(0) is enabled. If ethCfmMonitorAggregate(1) is disabled, the applicable Eth-CFM packet rate limit (tmnxCpmProtEthCfmPolRateLimit) applies per peer (i.e. on a source MAC address basis). For example, if the SAPs rate limit for all Eth-CFM packets is 100 packets/sec, and two peers are served by the SAP, then 100 Eth-CFM packets/sec from each peer is within the limit. If ethCfmMonitorAggregate(1) is enabled, the applicable Eth-CFM packet rate limit (tmnxCpmProtEthCfmPolRateLimit) applies to the aggregated traffic flow. For example, if the SAPs rate limit for all Eth-CFM packets is 100 packets/sec, and two peers are served by this SAP, then the combined rate of the two peers cannot exceed 100 packets/sec. ethCfmMonitorCommittedAccessRate(2) controls the interaction between two features: Eth-CFM rate limiting, and overall rate limiting (as configured using tmnxCpmProtPolOverallRateLimit). If ethCfmMonitorCommittedAccessRate(2) is disabled, an Eth-CFM packet is subjected to two rate limits, in the following order. a) The applicable tmnxCpmProtEthCfmPolRateLimit is applied, as described above. If the packet exceeds the limit, it is discarded. Otherwise... b) The SAPs tmnxCpmProtPolOverallRateLimit (which is applied to Eth-CFM packets, and the other rate limited packet types) is applied. If ethCfmMonitorCommittedAccessRate(2) is enabled, an Eth-CFM packet is subjected to one rate limit: the applicable tmnxCpmProtEthCfmPolRateLimit, as described above. Eth-CFM packets are neither counted nor discarded when performing the tmnxCpmProtPolOverallRateLimit rate limiting.

The value of sapTransitIpPolicyId specifies the transit IP policy to be associated with this SAP. The value must either be 0 indicating an invalid transit IP policy or the specified transit IP policy needs to exist in the TIMETRA-BSX-NG-MIB::tmnxBsxTransitIpPolicyTable. At most one of sapTransitIpPolicyId and sapTransitPrefixPolicyId can be non-zero.

The value of the sapOperGrp specifies the Operational-Group identifier associated with this SAP. An inconsistentValue error is returned when both sapOperGrp and sapMonitorOperGrp are set together and atleast one of them to a non-default value.

The value of the sapMonitorOperGrp specifies the Operational-Group identifier which will affect the state of this SAP. An inconsistentValue error is returned when both sapOperGrp and sapMonitorOperGrp are set together and atleast one of them to a non-default value.

The value of the sapEgressHsmdaWrrPolicyOvr specifies the egress hsmda weighted round-robin policy override for this SAP. When no policy is given, the hsmda weighted round-robin policy specified in the sap-egress policy is honored. When a valid policy is given, it is used instead of the hsmda weighted round-robin policy given in the sap-egress policy.

The value of sapTransitPrefixPolicyId specifies the transit prefix policy to be associated with this SAP. The value must either be 0 indicating an invalid transit prefix policy or the specified transit prefix policy needs to exist in the TIMETRA-BSX-NG-MIB::tmnxBsxTransPrefPolicyTable. At most one of sapTransitIpPolicyId and sapTransitPrefixPolicyId can be non-zero.

The value of sapCpmProtMonitorIP specifies whether or not to apply the tmnxCpmProtPolPerSrcRateLimit of this SAPs CPM Protection policy to IPv4 DHCP packets served by the SAP, on a per source IP address basis. For example, suppose sapCpmProtMonitorIP is true, and this SAPs sapCpmProtPolicyId points to a policy table row with tmnxCpmProtPolPerSrcRateLimit set to 100 packets/second. Suppose two source IP addresses (e.g. 138.120.141.173 and 138.120.141.174) each send 150 DHCP packets/second to this SAP. Approx. 50 DCHP packets/second from each source will be discarded. If the value of sapCpmProtPolicyId is equal to zero, the value of sapCpmProtMonitorIP is irrelevant and will be ignored. At most one of the following options can be enabled on this SAP: 1. sapCpmProtMonitorMac, 2. The sapCpmProtEthCfmMonitorFlags option ethCfmMonitor(0), 3. sapCpmProtMonitorIP.

The value of the object sapHostsAdminState specifies the administrative state of all hosts on this SAP. If set to down no dynamic subscriber hosts can be created, and any active dynamic host on the SAP will be removed.

The value of sapHostLockoutPolicy specifies the Host Lockout Policy for this SAP.

The value of sapAarpId specifies the AA Redundancy Protocol (AARP) instance associated with this SAP. If set to 0, no AARP instance is associated with this SAP.

The value of sapIngressFPQGrp specifies the forwarding-plane queue group Policy for this SAP. This object must be set along with sapIngressFPQGrpInstanceId object. An inconsistentValue error is returned if sapIngressFPQGrp is set to a non-default value and an entry corresponding to tmnxFPNum to which this SAP belongs does not exist in tmnxFPAccIngQGrpTable.

The value of sapIngressFPQGrpInstanceId specifies the instance of the forwarding-plane ingress Queue Group for this SAP. This object must be set along with sapIngressFPQGrp object. An inconsistentValue error is returned if sapIngressFPQGrp is set to a non-default value and an entry corresponding to tmnxFPNum to which this SAP belongs does not exist in tmnxFPAccIngQGrpTable.

The value of sapAarpServRefType specifies the role of the SAP referenced by the AA Redundancy Protocol (AARP) instance identified by sapAarpId. If sapAarpId is the invalid AARP instance 0, then the service reference type is none(0).

The value of sapSiteName indicates the site-name associated with this SAP.

The value of sapIgnoreOperDown specifiy whether service will ignore when sap is operationally down.

A table that contains TLS SAP information.

TLS specific information about a SAP.

The value of the object sapTlsStpAdminStatus specifies whether this SAP participates in the TLSs Spanning Tree Protocol. A SAP with a non-zero sapEthRingIndex does not participate in the TLSs Spanning Tree Protocol. The default value for sapTlsStpAdminStatus for these SAPs is disabled and may not be set to enabled.

The value of the object sapTlsStpPriority specifies the value of the port priority field which is contained in the most significant 4 bits of the 16-bit Port ID associated with this SAP. As only the most significant 4 bits of the value are used, the actual value of this object is limited to multiples of 16: e.g. the agent rounds down the value to one of: 0, 16, 32, .. , 224, 240.

The value of the object sapTlsStpPortNum specifies the value of the port number field which is contained in the least significant 12 bits of the 16-bit Port ID associated with this SAP. Values in the range 2048..4094 are automatically assigned by the agent when the SAP is created or when the value of this object is set to zero via management. Values in the range 1..2047 can be set via management, to allow this object to have a deterministic value across system reboots.

The value of the object sapTlsStpPathCost specifies the contribution of this port to the path cost of paths towards the spanning tree root which include this port.

The value of the object sapTlsStpRapidStart specifies whether Rapid Start is enabled on this SAP. When the value is enabled the Spanning Tree Protocol state transitions on this SAP are driven by the value of the HelloTime instead of the value of ForwardDelay, thus allowing a faster transition into the forwarding state. This parameter is also referred to as adminEdge.

The value of the object sapTlsStpBpduEncap specifies the type of encapsulation used on BPDUs sent out and received on this SAP.

The value of the object sapTlsStpPortState indicates the ports current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken state.

The value of the object sapTlsStpDesignatedBridge indicates the Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this ports segment.

The value of the object sapTlsStpDesignatedPort indicates the Port Identifier of the port on the Designated Bridge for this ports segment.

The value of the object sapTlsStpForwardTransitions indicates the number of times this port has transitioned from the Learning state to the Forwarding state.

The value of the object sapTlsStpInConfigBpdus indicates the number of Configuration BPDUs received on this SAP.

The value of the object sapTlsStpInTcnBpdus indicates the number of Topology Change Notification BPDUs received on this SAP.

This object specifies the number of bad BPDUs received on this SAP.

The value of the object sapTlsStpOutConfigBpdus indicates the number of Configuration BPDUs sent out this SAP.

This object specifies the number of Topology Change Notification BPDUs sent out this SAP.

The value of the object sapTlsStpOperBpduEncap indicates the operating encapsulation type used on BPDUs sent out and received on this SAP.

The value of the object sapTlsVpnId indicates the VPN ID of the associated service.

The Customer ID of the associated service.

The value of the object sapTlsMacAddressLimit specifies the maximum number of learned and static entries allowed in the FDB of this SAP. The value 0 means: no limit for this SAP. The maximum value of sapTlsMacAddressLimit is 511999, when the the value of TIMETRA-CHASSIS-MIB::tmnxChassisOperMode is d. The maximum value of sapTlsMacAddressLimit is 196607, when the the value of TIMETRA-CHASSIS-MIB::tmnxChassisOperMode is c. In other cases, the maximum value of sapTlsMacAddressLimit is 131071.

The value of the object sapTlsNumMacAddresses indicates the number of MAC addresses currently present in the FDB that belong to this SAP (Both learned and static MAC addresses are counted).

The value of the object sapTlsNumStaticMacAddresses indicates the number of static MAC addresses currently present in the FDB that belong to this SAP.

The value of the object sapTlsMacLearning specifies whether the MAC learning process is enabled for this SAP. The value is ignored if MAC learning is disabled on service level.

The value of the object sapTlsMacAgeing specifies whether the MAC aging process is enabled for this SAP. the value is ignored if MAC aging is disabled on service level.

The value of the object sapTlsStpOperEdge indicates the operational value of the Edge Port parameter. The object is initialized to the value of sapTlsStpRapidStart and is set FALSE on reception of a BPDU.

The value of the object sapTlsStpAdminPointToPoint specifies the administrative point-to-point status of the LAN segment attached to this sap. The value forceTrue means that this port should always be treated as if it is connected to a point-to-point link. The value of forceFalse means that this port should be treated as having a shared media connection.

sapTlsStpPortRole indicates the current role of the sap as defined by the Rapid Spanning Tree Protocol.

sapTlsStpAutoEdge specifies whether this SAP is enabled for auto-edge detection as defined by Rapid Spanning Tree Protocol.

sapTlsStpOperProtocol indicates whether stp, rstp or mstp is running on this SAP. If the protocol is not enabled on this SAP, the value notApplicable is returned.

The value of the object sapTlsStpInRstBpdus indicates the number of Rapid Spanning Tree (RST) BPDUs received on this SAP.

The value of the object sapTlsStpOutRstBpdus indicates the number of Rapid Spanning Tree (RST) BPDUs sent out on this SAP.

When sapTlsLimitMacMove value is set to blockable the agent will monitor the MAC relearn rate on this SAP, and it will block it when the re-learn rate specified by svcTlsMacMoveMaxRate is exceeded. When the value is nonBlockable this SAP will not be blocked, and another blockable SAP will be blocked instead.

The value of the object sapTlsDhcpSnooping specifies whether or not DHCP packets received on this SAP will be snooped. This object was made obsolete in the 3.0 release.

The value of the object sapTlsMacPinning specifies whether or not MAC address pinning is active on this SAP. The value will be set by default to disabled. However for a SAP that belongs to a residential SHG, the value is set to enabled by the system, and cannot be altered by the operator. Setting the value to enable disables re-learning of MAC addresses on other SAPs or spoke-SDPs within the same VPLS; the MAC address will hence remain attached to the SAP for the duration of its age-timer. This object has effect only for MAC addresses learned via the normal MAC learning process, and not for entries learned via DHCP.

with the object sapTlsMacAddressLimit a limit can be configured for the max number of MAC addresses that will be learned on this SAP. When this limit is reached, packets with unknown source MAC address are forwarded by default. By setting sapTlsDiscardUnknownSource to enabled, packets with unknown source MAC will be dropped in stead.

The value of sapTlsMvplsPruneState indicates the mVPLS prune state of the SAP. The object will be set to notApplicable if the SAP is not managed by a mVPLS. If the SAP is managed the state reflects whether or not the SAP is pruned by the STP instance running in the mVPLS instance.

The value of sapTlsMvplsMgmtService indicates the service Id of the service where the STP instance is running that is managing this SAP. This object is only valid if sapTlsMvplsPruneState is different from notApplicable.

The value of sapTlsMvplsMgmtPortId indicates the SAP port Id of the SAP in the mVPLS instance specified in sapTlsMvplsMgmtService that is controlling this SAP. This object is only valid if sapTlsMvplsPruneState is different from notApplicable.

The value of sapTlsMvplsMgmtEncapValue indicates the SAP Encap value of the SAP in the mVPLS instance specified in sapTlsMvplsMgmtService that is controlling this SAP. This object is only valid if sapTlsMvplsPruneState is different from notApplicable.

The value of the object sapTlsArpReplyAgent specifies the status of the special ARP response mechanism in the system for ARP requests destined to static or dynamic hosts associated with this SAP. disabled: the ARP reply function is not operational enabled: the ARP reply function is enabled without subscriber identification. enabledWithSubscrIdent: the ARP reply function is enabled with subscriber identification.

The value of the object sapTlsStpException indicates whether an STP exception condition is present on this Sap. - none : no exception condition found. - oneWayCommuniation : The neighbor RSTP peer on this link is not able to detect our presence. - downstreamLoopDetected :A loop is detected on this link.

The value of the object sapTlsAuthenticationPolicy specifies which subscriber authentication policy must be applied when a DHCP msg is received on the interface. The authentication policies must be defined in tmnxSubAuthPlcyTable. The policy will only be applied when sapTlsDhcpSnoop is enabled.

The value of the object sapTlsL2ptTermination specifies whether received Layer 2 Protocol Tunnel (L2PT) pdus are terminated on this port or sap.

The value of the object sapTlsBpduTranslation specifies whether received L2 Protocol Tunnel pdus are translated before being sent out on this port or sap.

The value of the object sapTlsStpRootGuard specifies whether this port is allowed to become STP root port. It corresponds to the parameter restrictedRole in 802.1Q. If set, it can cause lack of spanning tree connectivity.

The value of the object sapTlsStpInsideRegion indicates whether the network connected to the SAP is in the same MST region. It corresponds to the parameter infoInternal in 802.1Q.

The value of the object sapTlsEgressMcastGroup specifies the Egress Multicast Group this SAP belongs to.

The value of the object sapTlsStpInMstBpdus indicates the number of Multiple Spanning Tree (MST) BPDUs received on this SAP.

The value of the object sapTlsStpOutMstBpdus indicates the number of Multiple Spanning Tree (MST) BPDUs sent out on this SAP.

The value of the object sapTlsRestProtSrcMac specifies how the agent will handle relearn requests for protected MAC addresses. When the value of this object is true requests to relearn a protected MAC address will be ignored. In addition, if the value of sapTlsRestProtSrcMacAction is disable, then the SAP where the protected source MAC was seen will be brought operationally down.

The value of the object sapTlsRestUnprotDstMac specifies how the system will forward packets destined to an unprotected MAC address. When the value of this object is true packets destined to an unprotected MAC address will be dropped.

The value of the object sapTlsStpRxdDesigBridge indicates the designated Bridge Identifier in the last BPDU which was received on this SAP. It identifies which bridge is connected to the SAP.

The value of the object sapTlsStpRootGuardViolation indicates whether there is a root-guard violation at the present time. This can only happen when sapTlsStpRootGuard is set to true.

The value of the object sapTlsShcvAction indicates whether any action should be triggered when the connectivity check fails.

The value of the object sapTlsShcvSrcIp specifies the source IP address used when doing the connectivity check. The value 0.0.0.0 indicates that no host IP address is specified.

The value of the object sapTlsShcvSrcMac specifies the MAC address used when doing the connectivity check. The value 0:0:0:0:0:0 indicates that no host MAC address is specified.

The value of the object sapTlsShcvInterval specifies the interval in minutes between connectivity checks. Zero means no connectivity checking.

The value of the object sapTlsMvplsMgmtMsti indicates the MST-instance in the mVPLS instance specified in sapTlsMvplsMgmtService that is controlling this SAP. A value of 0 indicates the CIST. This object is only valid if sapTlsMvplsPruneState is different from notApplicable.

The value of the object sapTlsMacMoveNextUpTime counts down the time in seconds until a SAP that has been brought down due to exceeding the TLS svcTlsMacMoveMaxRate, sapOperFlags relearnLimitExceeded, is automatically brought up again. When this value is 0xffff, the SAP will never be automatically brought up. When sapOperStatus is up, this object counts down the time in seconds until the value of sapTlsMacMoveRateExcdLeft is reset.

The value of the object sapTlsMacMoveRateExcdLeft counts down the number of times this SAP can exceed the TLS svcTlsMacMoveMaxRate and still be automatically brought up.

The value of the object sapTlsRestProtSrcMacAction indicates the action to take whenever a relearn request for a protected MAC is received on a restricted SAP. When the value of this object is disable the SAP will be placed in the operational down state, with the operating flag recProtSrcMac set. When the value of this object is alarm-only, the SAP will be left up and only a notification, sapReceivedProtSrcMac, will be generated. When the value of this object is discardFrame, the SAP will start discarding the frame in addition to generating sapReceivedProtSrcMac notification.

The value of sapTlsL2ptForceBoundary specifies if sapTlsL2ptTermination is enforced for its managed SAPs. Setting the value of the object sapTlsL2ptForceBoundary of a SAP in a Management VPLS to `true forces all its managed SAPs to have sapTlsL2ptTermination enabled. This value can only be `true if the SAP belongs to a management VPLS. If this SAP has managed SAPs already with sapTlsL2ptTermination disabled, it is not allowed to set sapTlsL2ptForceBoundary to `true.

The value of the object sapTlsLimitMacMoveLevel specifies the hierarchy in which SAPs are blocked when a MAC-move limit is exceeded. When a MAC is moving among multiple SAPs or spoke-SDPs, the SAP bind or spoke-SDP bind with the lower level is blocked first. (tertiary is the lowest)

The value of the object sapTlsBpduTransOper indicates the operational bpdu encapsulation used for BPDU translated frames.

The value of sapTlsDefMsapPolicy specifies the default Managed SAP policy to use to create Managed SAPs when the response from the Radius server does not specify a Managed SAP policy. The value of sapTlsDefMsapPolicy is only valid for a SAP with a sapSubType value of capture. If the value is set to a non-empty string for a SAP with a sapSubType value other than capture, an inconsistentValue error will be returned. The Managed SAP policy must be defined in msapPlcyTable, otherwise an inconsistentValue error will be returned.

The value of the object sapTlsL2ptTermination specifies which L2 Protocol Tunnel pdus are terminated on this port or sap.

The value of the object sapTlsL2ptForceProtocols specifies which L2 Protocol Tunnel pdus must be terminated by SAPs managed by this SAP. This object is only relevant if the value of the object sapTlsL2ptForceBoundary is true. For every SAP managed by this SAP, each L2 protocol specified by sapTlsL2ptForceProtocols must be terminated, while other L2 protocols may or may not be terminated, depending on the value of sapTlsL2ptProtocols of that managed SAP.

The value of sapTlsPppoeMsapTrigger specifies whether the receipt of PPPoE trigger packets on a VPLS SAP with a sapSubType value of capture will result in a Radius authentication that will provide a service context and the creation of a SAP with a sapSubType value of managed. An attempt to set the value sapTlsPppoeMsapTrigger to true on a SAP with sapSubType other than capture will return an inconsistentValue error.

The value of sapTlsDhcpMsapTrigger specifies whether the receipt of DHCP trigger packets on this VPLS SAP with a sapSubType value of capture will result in a Radius authentication that will provide a service context and the creation of a SAP with a sapSubType value of managed. An attempt to set the value sapTlsDhcpMsapTrigger to true on a SAP with sapSubType other than capture will return an inconsistentValue error.

The value of sapTlsMrpJoinTime specifies a timer value in 10ths of seconds which determines the maximum rate at which attribute join messages can be sent on the SAP.

The value of sapTlsMrpLeaveTime specifies a timer value in 10ths of seconds which determines the amount of time a registered attribute is held in leave state before the registration is removed.

The value of sapTlsMrpLeaveAllTime specifies the a timer value in 10ths of seconds which determines the frequency where all attribute declarations on the SAP are all refreshed.

The value of sapTlsMrpPeriodicTime specifies a timer value in 10ths of seconds which determines the frequency of re-transmission of attribute declarations.

The value of sapTlsMrpPeriodicEnabled specifies whether re-transmission of attribute declarations is enabled.

The value of sapTlsPppoePolicy specifies the PPPoE policy (defined in TIMETRA-PPPOE-MIB::tmnxPppoePlcyTable) to use to create Managed SAPs via PPPoE with PAP/CHAP authentication. The value of sapTlsPppoePolicy is only valid for a SAP with a sapSubType value of capture. If the value is set to a non-empty string for a SAP with a sapSubType value other than capture, an inconsistentValue error will be returned. The value of sapTlsPppoePolicy is used for PPP sessions where the value of TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppType is equal to oE or oEoA. In general, the default value is empty; for a SAP with a sapSubType value of capture, the default value is equal to default.

The value of sapTlsArpMsapTrigger specifies whether the receipt of ARP trigger packets on this VPLS SAP with a sapSubType value of capture will result in a Radius authentication that will provide a service context and the creation of a SAP with a sapSubType value of managed. An attempt to set the value sapTlsArpMsapTrigger to true on a SAP with sapSubType other than capture will return an inconsistentValue error.

The value of sapTlsDefMsapService specifies the service ID of the service where Managed SAPs are created when there is no Radius server available, or the Radius server does not specify the service ID. The value of sapTlsDefMsapService is only relevant for a SAP with a sapSubType value of capture. While the value of sapTlsDefMsapService is equal to zero, no Managed SAPs are created when there is no Radius server-specified service ID available. For a SAP with a sapSubType value other than capture, zero is the only value allowed.

The value of sapTlsDefMsapGroupIf specifies the name of the group interface where Managed SAPs are created when there is no Radius server available, or the Radius server does not specify the group interface. The value of sapTlsDefMsapGroupIf is only relevant for a SAP with a sapSubType value of capture. While the value of sapTlsDefMsapGroupIf is the empty string, no Managed SAPs are created when there is no Radius server-specified group interface available. For a SAP with a sapSubType value other than capture, zero is the only value allowed.

The value of sapTlsMrpPolicy specifies the mrp policy to control which Group BMAC attributes will advertise on the egress SAP-SDP.

The value of sapTlsSiteName indicates the site-name associated with this SAP.

The value of sapTlsDhcp6MsapTrigger specifies whether the receipt of DHCPv6 trigger packets on this VPLS SAP with a sapSubType value of capture will result in a Radius authentication that will provide a service context and the creation of a SAP with a sapSubType value of managed. An attempt to set the value sapTlsDhcp6MsapTrigger to true on a SAP with sapSubType other than capture will return an inconsistentValue error.

The value of the object sapTlsShcvRetryTimeout specifies the timeout in seconds before a connectivity check retransmission.

The value of the object sapTlsShcvRetryCount specifies the number of connectivity check retransmissions. Setting the value to n specifies that, for any given host, at most (n+1) probes are done each interval, and (n+1) missed replies are considered as a connectivity failure.

The value of sapTlsDataSapInstStatus indicates the status of the SAP which is instantiating other SAPs controlled by this SAP. This object is valid for services with TIMETRA-SERV-MIB::svcMgmtVpls set to true.

The value of sapTlsDataSapInstLastErr indicates last error encountered while instantiating SAPs controlled by this SAP. This object is valid for services with TIMETRA-SERV-MIB::svcMgmtVpls set to true.

The value of sapTlsMvrpAdminStatus specifies whether MVRP is enabled on this SAP. The default value of sapTlsMvrpAdminStatus is set to enabled for MVRP enabled services.

The value of sapTlsMvrpOperStatus indicates operational status of MVRP on this SAP.

The value of the object sapTlsInTcBitBpdus indicates the number of BPDUs received on this SAP with the Topology Change bit set.

The value of the object sapTlsOutTcBitBpdus indicates the number of BPDUs sent out this SAP with the Topology Change bit set.

The value of sapTlsPppMsapTrigger specifies whether the receipt of PPP trigger packets on a VPLS SAP with a sapSubType value of capture will result in a Radius authentication that will provide a service context and the creation of a SAP with a sapSubType value of managed. An attempt to set the value sapTlsPppoeMsapTrigger to true on a SAP with sapSubType other than capture will return an inconsistentValue error.

The value of sapTlsPppPolicy specifies the policy (defined in TIMETRA-PPPOE-MIB::tmnxPppoePlcyTable) to use to create Managed SAPs via PPP with PAP/CHAP authentication. The value of sapTlsPppPolicy is only valid for a SAP with a sapSubType value of capture. If the value is set to a non-empty string for a SAP with a sapSubType value other than capture, an inconsistentValue error will be returned. The value of sapTlsPppPolicy is used for PPP sessions where the value of TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppType is equal to oA, as opposed to oE or oEoA. In general, the default value is empty; for a SAP with a sapSubType value of capture, the default value is equal to default.

The value of sapTlsTrackSrrpInst specifies the SRRP instance to track.

The value of sapTlsPppUserDb specifies the local user database to use for PPP PAP/CHAP based authentication. If no authentication with the local user database is required, the value of this object must be set to the empty string. The value of sapTlsPppUserDb is only valid for a SAP with a sapSubType value of capture. If the value is set to a non-empty string for a SAP with a sapSubType value other than capture, an inconsistentValue error will be returned. The value of sapTlsPppUserDb is used for PPP sessions where the value of TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppType is equal to oA, as opposed to oE or oEoA.

The value of sapTlsPppoeUserDb specifies the local user database to use for PPPoE PADI PAP/CHAP based authentication. If no authentication with the local user database is required, the value of this object must be set to the empty string. The value of sapTlsPppoeUserDb is only valid for a SAP with a sapSubType value of capture. If the value is set to a non-empty string for a SAP with a sapSubType value other than capture, an inconsistentValue error will be returned. The value of sapTlsPppoeUserDb is used for PPP sessions where the value of TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppType is equal to oE or oEoA, as opposed to oA.

The value of sapTlsDhcpUserDb specifies the local user database to use for DHCP based authentication. If no authentication with the local user database is required, the value of this object must be set to the empty string. The value of sapTlsDhcpUserDb is only valid for a SAP with a sapSubType value of capture. If the value is set to a non-empty string for a SAP with a sapSubType value other than capture, an inconsistentValue error will be returned.

The value of sapTlsAutoLearnMacProtect specifies whether to enable automatic population of the MAC protect list with source MAC addresses learned on the associated SAP.

A table that contains ATM SAP information.

Information about a specific ATM SAP.

This object specifies the data encapsulation used over the AAL5 SSCS layer. The definition references RFC 2684 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification.

This object specifies the index of the ATM traffic descriptor in the ATM traffic data encapsulation used in for the ingress direction over the AAL5 SSCS layer. The definition references RFC 2684 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification.

This object specifies the index of the ATM traffic descriptor in the ATM traffic data encapsulation used in for the egress direction over the AAL5 SSCS layer. The definition references RFC 2684 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification.

A value of up specifies that the OAM status of a pvc affects the sap operational status and OAM AIS/RDI cell generation upon a sap operational status of down. A value of down specifies that the OAM status of a pvc will not affect the operational status of the associated sap and no OAM AIS/RDI cells are generated.

The sapAtmOamTerminate object specifies whether this SAP will act as an OAM termination point. If enabled, OAM cells will be sunk by the SAP and can affect the SAPs operational status (if sapAtmOamAlarmCellHandling is also enabled). Otherwise the OAM cells will be passed into the APIPE service. This object is only configurable for ATM SAPs that are part of an APIPE service SDU or VCC mode. If the sapPortId belongs to an Multi-Chassis APS port, the default value is up.

The sapAtmOamPeriodicLoopback object specifies whether this SAP will run periodic OAM loopbacks or not. If enabled, an ATM OAM loopback cell will be transmitted every period as configured in tAtmSysOamLoopbackPeriod. If a response is not received and tAtmSysOamRetryDown consecutive retries also result in failure, the endpoint will transition to the eteAisLoc state. Once in the eteAisLoc state, an ATM OAM loopback cell will be transmitted every period as configured in tAtmSysOamLoopbackPeriod. If a response is received for the periodic loopback and tAtmSysOamRetryUp consecutive retries also each receive a response, the endpoint will transition back to the up state. This object is only configurable on IES or VPRN service endpoints.

sapAtmLLFAdminStatus specifies whether or not Link- Loss Forwarding is enabled (up). When this object is set to up the underlying port will be forced into the operationally down state if the service is operationally down, or any of the sdpBindPwPeerStatusBits are set, and will set the underlying ports tmnxPortReasonDownFlags linklossFwd bit. Setting this object to down will clear the linklossFwd reason. sapAtmLLFAdminStatus can only be enabled on saps configured for an APIPE service using an port with the tmnxPortEncapType set to atmEncap and sapEncapValue set for ATM ports.

sapAtmLLFOperStatus indicates whether or not the underlying port is forced operationally down due to the service being operationally down or an sdpBindPwPeerStatusBits bit is set. sapAtmLLFOperStatus is set to fault when the sapAtmLLFAdminStatus is set to up, and either a fault has occurred on the pseudo-wire, or the service is down, otherwise sapAtmLLFOperStatus is set to clear.

The value of sapAtmSubPppIndex indicates the local identifier of the subscriber PPP session. It is the index of the corresponding conceptual row in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppTable. The value zero indicates that there is no subscriber PPP session associated with this SAP.

This object indicates the AAL5 data encapsulation detected by PPPoA (PPP over ATM) or PPPoEoA (PPP over Ethernet over ATM). The value is only applicable if sapAtmEncapsulation is set to auto and returns unknown as long as no encapsulation is detected. If sapAtmEncapsulation is set to a value different than auto, sapAtmDetectedEncapsulation always returns the same value as sapAtmEncapsulation.

This object indicates the index of the ATM ingress traffic descriptor override. This override value is given by an AAA server such as a RADIUS server. The value zero indicates that no override is given.

This object indicates the index of the ATM egress traffic descriptor override. This override value is given by an AAA server such as a RADIUS server. The value zero indicates that no override is given.

A table that contains basic SAP statistics. In the descriptions below Pchip refers to the Alcatel-Lucent SROS series Packet Processing chip, while Qchip refers to the Alcatel-Lucent SROS series QoS Queueing Engine chip.

Basic statistics about a specific SAP.

The number of packets dropped by the ingress Pchip due to: SAP state, ingress MAC, IP or IPv6 filter, same segment discard, bad checksum, etc.

The number of octets dropped by the ingress Pchip due to: SAP state, ingress MAC, IP or IPv6 filter, same segment discard, bad checksum, etc.

The number of high priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The number of high priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The number of low priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The number of low priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of high priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of in-profile packets (rate below CIR) forwarded by the ingress Qchip.

The number of in-profile octets (rate below CIR) forwarded by the ingress Qchip.

The number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip.

The number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip.

The number of in-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of in-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of in-profile packets (rate below CIR) forwarded by the egress Qchip.

The number of in-profile octets (rate below CIR) forwarded by the egress Qchip.

The number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip.

The number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip.

The Customer ID for the associated service.

The number of uncolored packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The number of uncolored octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The number of DHCP packets discarded as result of authentication.

The number of DHCP packets successfully authenticated.

The value of sapBaseStatsLastClearedTime indicates the sysUpTime when the counters in this table were last cleared.

The value of sapBaseStatsIngressCPMPackets indicates ingress traffic in terms of packets destined to CPM associated with this SAP.

The value of sapBaseStatsIngressCPMPacketsHi indicates upper 32 bits of sapBaseStatsIngressCPMPackets object.

The value of sapBaseStatsIngressCPMPacketsHi indicates lower 32 bits of sapBaseStatsIngressCPMPackets object.

The value of sapBaseStatsIngressCPMOctets indicates ingress traffic in terms of bytes destined to CPM associated with this SAP.

The value of sapBaseStatsIngressCPMOctetsHi indicates upper 32 bits of sapBaseStatsIngressCPMOctets object.

The value of sapBaseStatsIngressCPMOctetsHi indicates lower 32 bits of sapBaseStatsIngressCPMOctets object.

A table that contains ingress QoS queue SAP statistics.

Ingress statistics about a specific SAPs QoS queue.

The index of the ingress QoS queue of this SAP.

The number of high priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of low priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of high priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The number of high priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of low priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of in-profile packets (rate below CIR) forwarded by the ingress Qchip.

The number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip.

The number of in-profile octets (rate below CIR) forwarded by the ingress Qchip.

The number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip.

The Customer ID for the associated service.

The number of uncolored packets offered to the ingress Qchip.

The number of uncolored octets offered to the ingress Qchip.

A table that contains egress QoS queue SAP statistics.

Egress statistics about a specific SAPs QoS queue.

The index of the egress QoS queue of this SAP.

The number of in-profile packets (rate below CIR) forwarded by the egress Qchip.

The number of in-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip.

The number of out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of in-profile octets (rate below CIR) forwarded by the egress Qchip.

The number of in-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip.

The number of out-of-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The Customer ID for the associated service.

A table that contains ingress QoS queue SAP statistics.

Ingress statistics about a specific SAPs QoS queue.

The index of the ingress QoS scheduler of this SAP.

The number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

The number of forwarded octets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

The Customer ID for the associated service.

A table that contains ingress QoS queue SAP statistics.

Egress statistics about a specific SAPs QoS queue.

The index of the egress QoS scheduler of this SAP.

The number of forwarded packets by the egress Qchip, as determined by the SAP egress scheduler policy.

The number of forwarded octets by the egress Qchip, as determined by the SAP egress scheduler policy.

The Customer ID for the associated service.

This table is used only for SAPs that are part of a management VPLS. It indicates for each SAP the ranges of associated VLANs that will be affected when the SAP changes state.

Each row specifies a range of VLANS associated with a SAP of a MVPLS. Ranges may contains overlapping sections only for Mvpls SAPs that belong to the same service.

The value of sapTlsMvplsMinVlanTag specifies the left bound (i.e. min. value) of a range of VLANs that are associated with the Mvpls SAP. sapTlsMvplsMinVlanTag must be smaller than (or equal to) sapTlsMvplsMaxVlanTag. Special values are: 0: this value is reserved for the null tag. 4095: this value denotes the default SAP.

The value of sapTlsMvplsMaxVlanTag specifies the right bound (i.e. max. value) of a range of VLANs that are associated with the Mvpls SAP. Special values are: 0: this value is reserved for the null tag. 4095: this value denotes the default SAP.

The value of sapTlsMvplsRowStatus specifies the status of this row. The only values supported during a set operation are createAndGo and destroy. A row (i.e. a range of VLAN tags) can be destroyed only if there are no SAPs defined in regular VPLSses in this range.

The sapAntiSpoofTable contains information about anti-spoofing filters on a SAP.

An entry in the sapAntiSpoofTable.

The value of sapAntiSpoofIpAddress indicates the IP address for which this table entry contains information.

The value of sapAntiSpoofMacAddress indicates the MAC address for which this table entry contains information.

The sapStaticHostTable is used to configure static hosts on a SAP.

Each row entry represents information on a statically configured host. Entries can be created and deleted via SNMP SET operations.

The value of the object sapStaticHostRowStatus controls the creation and deletion of rows in this table.

The value of the object sapStaticHostIpAddress specifies the IP address associated with this static host. The value 0.0.0.0 indicates that no host IP address is specified.

The value of the object sapStaticHostMacAddress specifies the MAC address associated with this static host. The value 0:0:0:0:0:0 indicates that no host MAC address is specified.

The value of the object sapStaticHostSubscrIdent specifies the subscriber identification for this static host.

The value of the object sapStaticHostSubProfile specifies the subscriber profile for this static host. The specified subscriber profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubProfileTable.

The value of the object sapStaticHostSlaProfile specifies the SLA profile for this static host. The specified SLA profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSLAProfileTable.

The value of the object sapStaticHostShcvOperState gives the state of the subscriber host connectivity check for this static host.

The value of the object sapStaticHostShcvChecks specifies the number of connectivity checks for this static host.

The value of the object sapStaticHostShcvReplies specifies the number of host replies for this static host.

The value of the object sapStaticHostShcvReplyTime gives the timestamp of the last successful connectivity check for this static host.

The value of the object sapStaticHostDynMacAddress gives the MAC address learned via ARP in case this is an IP-only static host (sapStaticHostMacAddress is set to 0:0:0:0:0:0). The value 0:0:0:0:0:0 indicates that no MAC address is learned yet.

The value of the object sapStaticHostRetailerSvcId indicates the service ID of the retailer VPRN service to which this static host belongs. When this object is non zero, the static host belongs to a retailer VPRN.

The value of the object sapStaticHostRetailerIf indicates the interface index of the retailer VPRN interface to which this static host belongs. When this object is non zero, the static host belongs to a retailer VPRN.

The value of sapStaticHostFwdingState indicates the forwarding state of this static host. When the value is outOfService, host traffic is not forwarded. When it is inService, host traffic is forwarded.

The value of sapStaticHostAncpString specifies the ancp-string associated to this SAP host.

The value of the object sapStaticHostSubIdIsSapId specifies whether the SAP-id is taken as subscriber identification for this static host.

The value of sapStaticHostAppProfile specifies the application profile for this static host. The specified application profile needs to exist in the TIMETRA-BSX-NG-MIB::tmnxBsxAppProfTable.

The value of sapStaticHostIntermediateDestId specifies to which intermediate destination (for example a DSLAM) this host belongs.

The value of sapStaticHostAdminStatus specifies the administrative status of this host.

The value of the object sapStaticHostFilterProfile specifies the filter profile for this static host. The specified filter profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubFilterProfileTable.

sapTlsDhcpInfoTable contains DHCP information related to a TLS SAP. This table complements sapTlsInfoTable, and contains an entry for each Tls SAP. Rows in this table are created and deleted automatically by the system.

DHCP specific information for a TLS SAP.

The value of the object sapTlsDhcpAdminState specifies the overall enable/disable state of all DHCP related actions on this Sap. The value disabled allows the user to configure individual DHCP commands but administratively disable them.

The value of the object sapTlsDhcpDescription specifies a user provided description for DHCP on this Sap. It consists of any printable, seven-bit ASCII characters up to 80 characters in length.

The value of the object sapTlsDhcpSnoop specifies the enable/disable state for DHCP snooping on this Sap. Note that in order for snooping to be enabled the object sapTlsDhcpAdminState must also have the value enabled.

The value of the object sapTlsDhcpLeasePopulate specifies the maximum number of DHCP lease states allowed on this SAP.

The value of the object sapTlsDhcpOperLeasePopulate indicates the number of DHCP lease states currently allocated on this SAP.

The value of the object sapTlsDhcpInfoAction specifies the DHCP option reforwarding policy: replace - replace existing information with configured information drop - discard messages with existing relay information if the option-82 information is also present. keep - retain the existing relay information.

The value of the object sapTlsDhcpCircuitId specifies whether or not the circuit-id suboption is present, and if it is present what information goes in it: - none the circuit-id suboption will not be part of the information option (Option 82). - asciiTuple the ASCII-encoded concatenated tuple consisting of the - access-node-identifier - service-id - interface-name is used. - vlanAsciiTuple the format will include VLAN-id and dot1p bits in addition to what is included in ascii-tuple already. The format is supported on dot1q and qinq encapsulated ports only. Thus, when the option 82 bits are stripped, dot1p bits will be copied to the Ethernet header of an outgoing packet.

The value of the object sapTlsDhcpRemoteId specifies what information goes into the remote-id suboption in the DHCP Relay packet. If the value of this object is set to none, the remote-id suboption will not be part of the information option (Option 82). If the value of this object is set to mac, the MAC address of the remote end is encoded in the suboption. If the value of this object is set to remote-id, sapTlsDhcpRemoteIdString will represent the remote-id. By default, the remote-id value is none.

The value of the object sapTlsDhcpRemoteIdString specifies the remote-id. This object exists only if sapTlsDhcpRemoteId has a value of remote-id.

The value of sapTlsDhcpProxyAdminState specifies the desired administrative state of the proxy server on this interface. Note that in order for the proxy server to be enabled, the value of sapTlsDhcpAdminState must also be enabled.

The value of sapTlsDhcpProxyServerAddr specifies the IP address which will be used as the source address of the emulated DHCP server in the context of this VPLS SAP. This address is mandatory for the proxy server capability and it should be in the context of the subnet represented by this VPLS.

The value of sapTlsDhcpProxyLeaseTime specifies in seconds how long a DHCP client is allowed to use the offered IP address. Value 0 means the lease time provided by a RADIUS or an upstream DHCP server will not be overridden. A lease time of 7 days is used when RADIUS does not provide a lease time.

The value of sapTlsDhcpProxyLTRadiusOverride specifies whether or not the lease time provided by the RADIUS server is presented to the DHCP client. By default the proxy-server will always make use of sapTlsDhcpProxyLeaseTime, regardless of what lease time information is provided from the RADIUS server. When sapTlsDhcpProxyLTRadiusOverride is set to true, the proxy-server will use the lease time information provided by the RADIUS server, regardless of the configured one.

The value of sapTlsDhcpVendorIncludeOptions specifies what is encoded in the Alcatel-Lucent vendor specific sub-option of option 82. The value of this object is only used when sapTlsDhcpInfoAction is replace.

The value of sapTlsDhcpVendorOptionString specifies the string that goes into the Alcatel-Lucent vendor specific sub-option of option 82. This string is only used when sapTlsDhcpInfoAction is set to replace.

sapTlsDhcpStatsTable contains DHCP statistics related to a TLS SAP. This table complements sapTlsInfoTable, and contains an entry for each Tls SAP. Rows in this table are created and deleted automatically by the system.

DHCP statistics for a TLS SAP.

The value of the object sapTlsDhcpStatsClntSnoopdPckts indicates the number of DHCP client packets that have been snooped on this SAP.

The value of the object sapTlsDhcpStatsSrvrSnoopdPckts indicates the number of DHCP server packets that have been snooped on this SAP.

The value of the object sapTlsDhcpStatsClntForwdPckts indicates the number of DHCP client packets that have been forwarded on this SAP.

The value of the object sapTlsDhcpStatsSrvrForwdPckts indicates the number of DHCP server packets that have been forwarded on this SAP.

The value of the object sapTlsDhcpStatsClntDropdPckts indicates the number of DHCP client packets that have been dropped on this SAP.

The value of the object sapTlsDhcpStatsSrvrDropdPckts indicates the number of DHCP server packets that have been dropped on this SAP.

The value of the object sapTlsDhcpStatsClntProxRadPckts indicates the number of DHCP client packets that have been proxied on this SAP based on data received from a RADIUS server.

The value of the object sapTlsDhcpStatsClntProxLSPckts indicates the number of DHCP client packets that have been proxied on this SAP based on a lease state. The lease itself can have been obtained from a DHCP or RADIUS server. This is the so called lease split functionality.

The value of the object sapTlsDhcpStatsGenReleasePckts indicates the number of DHCP RELEASE messages spoofed on this SAP to the DHCP server.

The value of the object sapTlsDhcpStatsGenForceRenPckts indicates the number of DHCP FORCERENEW messages spoofed on this SAP to the DHCP clients.

sapTlsDhcpLeaseStateTable contains DHCP lease state info for a TLS SAP. This table complements sapTlsInfoTable, and contains an entry for each Tls SAP. Rows in this table are created and deleted automatically by the system. The content of this table is moved to the svcDhcpLeaseStateTable.

DHCP Lease State information on a TLS SAP.

The value of the object sapTlsDhcpLseStateCiAddr indicates the IP address of the DHCP lease state.

The value of the object sapTlsDhcpLseStateChAddr indicates the MAC address of the DHCP lease state.

The value of the object sapTlsDhcpLseStateRemainLseTime indicates the remaining lease time of the Ip address of the DHCP lease state. This object was made obsolete in the 4.0 release.

The value of the object sapTlsDhcpLseStateOption82 indicates the content of the Option82 for this DHCP lease state. This object was made obsolete in the 4.0 release.

The value of the object sapTlsDhcpLseStatePersistKey indicates a key value that can be used to track this lease state in the persistence file. This object was made obsolete in the 4.0 release.

The sapPortIdIngQosSchedStatsTable contains ingress QoS queue SAP statistics. This table is used when the SAP is a CCAG or LAG in link mode, or an APS.

Each entry represents the ingress statistics about a specific SAPs QoS queue. Entries are created when a scheduler policy is applied to a SAP.

The value of sapPortIdIngQosSchedName is used as an index of the ingress QoS scheduler of this SAP.

The value of sapPortIdIngPortId is used as an index of the ingress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in link mode, this object is the TmnxPortID of the member-port on which the scheduler is applied.

The value of sapPortIdIngQosSchedFwdPkts indicates the number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

The value of sapPortIdIngQosSchedFwdOctets indicates the number of forwarded octets,as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

The value of sapPortIdIngQosSchedCustId indicates the Customer ID for the associated service.

The sapPortIdEgrQosSchedStatsTable contains egress QoS queue SAP statistics. This table is used when the SAP is a CCAG or LAG in link mode, or an APS.

Each entry represents the egress statistics about a specific SAPs QoS queue. Entries are created when a scheduler policy is applied to a SAP.

The value of sapPortIdEgrQosSchedName is used as an index of the egress QoS scheduler of this SAP.

The value of sapPortIdEgrPortId is used as an index of the egress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in link mode, this object is the TmnxPortID of the member-port on which the scheduler is applied.

The value of sapPortIdEgrQosSchedFwdPkts indicates the number of forwarded packets, as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip.

The value of sapPortIdEgrQosSchedFwdOctets indicates the number of forwarded octets,as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip.

The value of sapPortIdEgrQosSchedCustId indicates the Customer ID for the associated service.

This table is used to override the base parameters of a queue, as defined in the associated SAP ingress QoS policy.

Override values for the specified SAP ingress QoS queue. These values override the corresponding ones specified in the associated SAP ingress QoS policy.

The value of sapIngQosQId indicates the ID of the queue whose parameters are to be overridden.

The value of sapIngQosQRowStatus controls the creation and deletion of rows in this table.

The value of sapIngQosQLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row.

The value of sapIngQosQOverrideFlags specifies the set of attributes whose values have been overridden via management on this queue. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAPs ingress QoS policy.

The value of sapIngQosQCBS specifies the amount of reserved buffer space (in kilo bytes) for this queue.

The value of sapIngQosQMBS specifies the maximum amount of buffer space (in kilo bytes) allowed for this queue.

The value of sapIngQosQHiPrioOnly specifies the percentage of buffer space for this queue, used exclusively by high priority packets.

The value of sapIngQosQCIRAdaptation specifies the criteria to use to compute the operational CIR value for this queue, while maintaining a minimum offset.

The value of sapIngQosQPIRAdaptation specifies the criteria to use to compute the operational PIR value for this queue, while maintaining a minimum offset.

The value of sapIngQosQAdminPIR specifies the desired PIR value for this queue.

The value of sapIngQosQAdminCIR specifies the desired CIR value for this queue.

The value of sapIngQosQMBSBytes specifies the maximum amount of buffer space (in bytes) allowed for this queue.

The value of sapIngQosQWeight specifies the weight that needs to be used by the scheduler to which this queue would be feeding.

The value of sapIngQosQCIRWeight specifies the weight that should be assigned to this queue by the parent scheduler among all the entities feeding into the parent, when the traffic is conforming to the committed rate. A value of 0 specifies that the queue will not receive bandwidth for the within-cir pass on its parent scheduler.

The value of sapIngQosQAdminPIRPercent specifies the desired PIR value for this queue as a percentage.

The value of sapIngQosQAdminCIRPercent specifies the desired CIR value for this queue as a percentage.

This table is used to override the base parameters of a queue, as defined in the associated SAP egress QoS policy.

Override values for the specified SAP egress QoS queue. These values override the corresponding ones specified in the associated SAP egress QoS policy.

The value of sapEgrQosQId indicates the ID of the queue whose parameters are to be overridden.

The value of sapEgrQosQRowStatus controls the creation and deletion of rows in this table.

The value of sapEgrQosQLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row.

The value of sapEgrQosQOverrideFlags specifies the set of attributes whose values have been overridden via management on this queue. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAPs ingress QoS policy.

The value of sapEgrQosQCBS specifies the amount of reserved buffer space (in kilo bytes) for this queue.

The value of sapEgrQosQMBS specifies the maximum amount of buffer space (in kilo bytes) allowed for this queue.

The value of sapEgrQosQHiPrioOnly specifies the percentage of buffer space for this queue, used exclusively by high priority packets.

The value of sapEgrQosQCIRAdaptation specifies the criteria to use to compute the operational CIR value for this queue, while maintaining a minimum offset.

The value of sapEgrQosQPIRAdaptation specifies the criteria to use to compute the operational PIR value for this queue, while maintaining a minimum offset.

The value of sapEgrQosQAdminPIR specifies the desired PIR value for this queue.

The value of sapEgrQosQAdminCIR specifies the desired CIR value for this queue.

The value of sapEgrQosQAvgOverhead specifies the encapsulation overhead, in hundredths of a percent, used to translate packet-based rate to frame-based rate and vice versa.

The value of sapEgrQosQMBSBytes specifies the maximum amount of buffer space (in bytes) allowed for this queue.

The value of sapEgrQosQWeight specifies the weight that needs to be used by the scheduler to which this queue would be feeding.

The value of sapEgrQosQCIRWeight specifies the weight that should be assigned to this queue by the parent scheduler among all the entities feeding into the parent, when the traffic is conforming to the committed rate. A value of 0 specifies that the queue will not receive bandwidth for the within-cir pass on its parent scheduler.

The value of sapEgrQosQAdminPIRPercent specifies the desired PIR value for this queue as a percentage.

The value of sapEgrQosQAdminCIRPercent specifies the desired CIR value for this queue as a percentage.

This table is used to override the base parameters of a virtual scheduler, as defined in the associated SAP ingress scheduler policy.

Override values for the specified SAP ingress virtual scheduler. These values override the corresponding ones specified in the associated SAP ingress scheduler policy.

The value of sapIngQosSName indicates the name of the virtual scheduler whose parameters are to be overridden.

The value of sapIngQosSRowStatus controls the creation and deletion of rows in this table.

The value of sapIngQosSLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row.

The value of sapIngQosSOverrideFlags specifies the set of attributes whose values have been overridden via management on this virtual scheduler. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAPs ingress scheduler policy.

The value of sapIngQosSPIR specifies the desired PIR value for this virtual scheduler.

The value of sapIngQosSCIR specifies the desired CIR value for this virtual scheduler.

The value of sapIngQosSSummedCIR specifies if the CIR should be used as the summed CIR values of the children schedulers or queues. If set to true, the applicable scheduler CIR (sapIngQosSCIR) loses its meaning.

This table is used to override the base parameters of a virtual scheduler, as defined in the associated SAP egress scheduler policy.

Override values for the specified SAP egress virtual scheduler. These values override the corresponding ones specified in the associated SAP egress scheduler policy.

The value of sapEgrQosSName indicates the name of the virtual scheduler whose parameters are to be overridden.

The value of sapEgrQosSRowStatus controls the creation and deletion of rows in this table.

The value of sapEgrQosSLastMgmtChange indicates the value of sysUpTime at the time of the last management change of any writable object of this row.

The value of sapEgrQosSOverrideFlags specifies the set of attributes whose values have been overridden via management on this virtual scheduler. Clearing a given flag will return the corresponding overridden attribute to the value defined on the SAPs egress scheduler policy.

The value of sapEgrQosSPIR specifies the desired PIR value for this virtual scheduler.

The value of sapEgrQosSCIR specifies the desired CIR value for this virtual scheduler.

The value of sapEgrQosSSummedCIR specifies if the CIR should be used as the summed CIR values of the children schedulers or queues. If set to true, the applicable scheduler CIR (sapEgrQosSCIR) loses its meaning.

A table that contains SAP subscriber management information.

Subscriber management specific information about a SAP.

The value of sapSubMgmtAdminStatus specifies whether enhanced subscriber management is enabled on this SAP.

The value of sapSubMgmtDefSubProfile specifies the default subscriber profile applicable on this SAP. The corresponding profile is defined in TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubProfileTable. A value of default is not allowed for this object.

The value of sapSubMgmtDefSlaProfile specifies the default SLA profile applicable on this SAP. The corresponding profile is defined in TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSLAProfileTable.

The value of sapSubMgmtSubIdentPolicy specifies the subscriber identification policy applicable on this SAP. The corresponding policy is defined in TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubIdentPolicyTable.

The value of sapSubMgmtSubscriberLimit specifies the maximum number of subscribers allowed for this SAP. If the value is 0, there is no limit. Only if the value is 1, the single-sub-parameters defined with objects sapSubMgmtProfiledTrafficOnly, sapSubMgmtNonSubTrafficSubProf and sapSubMgmtNonSubTrafficSlaProf are meaningful.

The value of sapSubMgmtProfiledTrafficOnly specifies whether only profiled traffic is applicable for this SAP. If set to true, all SAP queues will be deleted. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1.

The value of sapSubMgmtNonSubTrafficSubIdent specifies the subscriber identification applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1.

The value of sapSubMgmtNonSubTrafficSubProf specifies the subscriber profile applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1.

The value of sapSubMgmtNonSubTrafficSlaProf specifies the SLA profile applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1.

The value of sapSubMgmtMacDaHashing specifies whether subscriber traffic egressing a LAG SAP has its egress LAG link selected by a function of the MAC destination address instead of subscriber id. The value of this object is only meaningful if sapSubMgmtAdminStatus is set to enabled and can only be configured for TLS services.

The value of sapSubMgmtDefSubIdent specifies what is used as the default subscriber identification applicable on this SAP. This value is used in case no other source (like Radius) provides a subscriber identification string. If the value of this objects is set to useSapId, the SAP-id is used as the default subscriber identification string. In this case, sapSubMgmtDefSubIdentString must contain the empty string. If the value of this objects is set to useAutoId, the auto-generated subscriber identification string, as defined in tmnxSubMgmtAutoSubIdObjs, is used as the default subscriber identification string. In this case, sapSubMgmtDefSubIdentString must contain the empty string. If the value of this object is set to useString, the value of sapSubMgmtDefSubIdentString is used as the default subscriber identification string. In this case, an empty sapSubMgmtDefSubIdentString means that there is no default subscriber identification configured.

The value of sapSubMgmtDefSubIdentString specifies the default subscriber identification string applicable on this SAP.

The value of sapSubMgmtDefAppProfile specifies the default application profile applicable on this SAP. The corresponding profile is defined in TIMETRA-BSX-NG-MIB::tmnxBsxAppProfTable.

The value of sapSubMgmtNonSubTrafficAppProf specifies the application profile applicable on this SAP for all non-subscriber traffic. The value of this object is only meaningful if sapSubMgmtSubscriberLimit is set to 1.

The value of sapSubMgmtDefInterDestId specifies what is used as the default intermediate destination identifier applicable on this SAP. This value is used in case no other source (like Radius) provides an intermediate destination identifier. If the value of this object is set to useString, the value of sapSubMgmtDefInterDestIdString is used as the default intermediate destination identifier. In this case, an empty sapSubMgmtDefInterDestIdString means that there is no default intermediate destination identifier configured. If the value of this object is set to useTopQTag, the top q-tag of this SAP is used as the default intermediate destination identifier. In this case, sapSubMgmtDefInterDestIdString must contain the empty string. If the value of this object is set to useVpi, the ATM VPI of this SAP is used as the default intermediate destination identifier. In this case, sapSubMgmtDefInterDestIdString must contain the empty string.

The value of sapSubMgmtDefInterDestIdString specifies the default intermediate destination identifier applicable on this SAP.

The value of the object sapSubMgmtDefFilterProfile specifies the default filter profile for this SAP. The specified filter profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubFilterProfileTable.

This table contains Multiple Spanning Tree Instance information for the SAP. Each management VPLS running MSTP can have upto 15 MSTI. An entry in this table is automatically created when a tlsMstiEntry is created.

Information about a specific MSTI for a SAP.

The value of the object sapTlsMstiPriority specifies the value of the port priority field which is contained in the most significant 4 bits of the 16-bit Port ID associated with this SAP and MSTI. As only the most significant 4 bits of the value are used, the actual value of this object is limited to multiples of 16: e.g. the agent rounds down the value to one of: 0, 16, 32, .. , 224, 240.

The value of the object sapTlsMstiPathCost specifies the contribution of this port to the MSTI path cost of paths towards the spanning tree regional root which include this port.

The value of the object sapTlsMstiLastMgmtChange indicates the value of sysUpTime at the time of the most recent management-initiated change to this SAP MSTI information.

sapTlsMstiPortRole indicates the current role of the sap in the MSTI as defined by the Spanning Tree Protocol.

The value of the object sapTlsMstiPortState indicates the ports current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken state.

The value of the object sapTlsMstiDesignatedBridge indicates the Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this ports segment for this MSTI.

The value of the object sapTlsMstiDesignatedPort indicates the Port Identifier of the port on the Designated Bridge for this ports segment for this MSTI.

A table that contains IPIPE specific SAP information.

IPIPE specific information about a SAP.

The value of the object sapIpipeCeInetAddressType specifies the addresstype of the local end host IP of an IPIPE. This object is only configurable if the value of svcIpipeCeAddressDiscovery is disabled.

The type of this address is determined by the value of the sapIpipeCeInetAddressType object. This object specifies the IPv4 address of the local end host of an IPIPE. This object is only configurable if the value of svcIpipeCeAddressDiscovery is disabled.

The value of sapIpipeMacRefreshInterval specifies the interval between successive attempts to refresh the MAC address of the CE device associated with an Ethernet ipipe SAP. If no other event (such as reception of an ARP request from the CE) occurs that would refresh the MAC address before the end of the interval, an ARP request will be originated from the IPIPE SAP.

The value of the object sapIpipeMacAddress specifies the MAC address of an IPIPE Ethernet SAP.

The value of the object sapIpipeArpedMacAddress indicates the MAC address of the local end host.

The value of the object sapIpipeArpedMacAddressTimeout indicates the number of seconds to wait for the sapIpipeArpedMacAddress to be re-refreshed.

The value of the object sapIpipeDiscoveredCeInetAddrType indicates the addresstype of the local end discovered host IP of an IPIPE SAP.

The type of this address is determined by the value of the sapIpipeDiscoveredCeInetAddrType object. This object indicates the IPv4 address of the discovered local end host of an IPIPE SAP.

The value of sapIpipeUseBroadcastMac specifies whether to use a broadcast MAC address to forward traffic from the Ethernet Ipipe SAP when sapIpipeArpedMacAddress is not a valid MAC address (no ARPed MAC address). If svcIpipeCeAddressDiscovery is set to disabled (2), this value cannot be changed from the default value. For non-Ethernet SAPs this value cannot be changed from the default value.

The value of sapIpipeUsingBroadcastMac indicates whether a broadcast MAC address is currently being used to forward traffic from the Ethernet Ipipe SAP.

This object indicates the discovered link local IPv6 address of the local end host of an IPIPE SAP.

This object indicates the discovered global IPv6 address of the local end host of an IPIPE SAP.

The value of the object sapIpipeIpv6DiscoveredMacAddress indicates the MAC address of the IPv6 local end host.

This table contains information on configurable objects on SAP level, that can be modified by a scheduled policy.

Information about ToD policy modifiable config data for a SAP.

The value of the object sapCurrentIngressIpFilterId indicates the index in the tIPFilterTable corresponding to the ingress filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressIpFilterId in case it is overruled by a ToD Suite policy.

The value of the object sapCurrentIngressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the ingress Ipv6 filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressIpv6FilterId in case it is overruled by a ToD Suite policy.

The value of the object sapCurrentIngressMacFilterId indicates the index in the tMacFilterTable corresponding to the ingress Mac filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressMacFilterId in case it is overruled by a ToD Suite policy.

The value of the object sapCurrentIngressQosPolicyId indicates the index in the tSapIngressTable corresponding to the ingress Qos Policy applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapIngressQosPolicyId in case it is overruled by a ToD Suite policy.

The value of the object sapCurrentIngressQosSchedPlcy indicates the ingress QoS scheduler on this SAP, or zero if none is currently active. The active policy may deviate from sapIngressQosSchedulerPolicy in case it is overruled by a ToD Suite policy defined on this SAP, or on the multi-service this SAP belongs to.

The value of the object sapCurrentEgressIpFilterId indicates the index in the tIPFilterTable corresponding to the Egress filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressIpFilterId in case it is overruled by a ToD Suite policy.

The value of the object sapCurrentEgressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the Egress Ipv6 filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressIpv6FilterId in case it is overruled by a ToD Suite policy.

The value of the object sapCurrentEgressMacFilterId indicates the index in the tMacFilterTable corresponding to the Egress Mac filter applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressMacFilterId in case it is overruled by a ToD Suite policy.

The value of the object sapCurrentEgressQosPolicyId indicates the index in the tSapEgressTable corresponding to the Egress Qos Policy applied on this SAP, or zero if no filter is currently active. The active filter may deviate from sapEgressQosPolicyId in case it is overruled by a ToD Suite policy.

The value of the object sapCurrentEgressQosSchedPlcy indicates the Egress QoS scheduler on this SAP, or zero if none is currently active. The active policy may deviate from sapEgressQosSchedulerPolicy in case it is overruled by a ToD Suite policy defined on this SAP, or on the multi-customer this SAP belongs to.

The value of the object sapIntendedIngressIpFilterId indicates the index in the tIPFilterTable corresponding to the ingress IP filter that should be applied on this SAP. If it deviates from sapCurrentIngressIpFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

The value of the object sapIntendedIngressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the ingress Ipv6 filter that should be applied on this SAP. If it deviates from sapCurrentIngressIpv6FilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

The value of the object sapIntendedIngressMacFilterId indicates the index in the tMacFilterTable corresponding to the ingress Mac filter that should be applied on this SAP. If it deviates from sapCurrentIngressMacFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

The value of the object sapIntendedIngressQosPolicyId indicates the index in the tSapIngressTable corresponding to the ingress Qos policy that should be applied on this SAP. If it deviates from sapCurrentIngressQosPolicyId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

The value of the object sapIntendedIngressQosSchedPlcy indicates the ingress QoS scheduler that should be applied on this SAP. If it deviates from sapCurrentIngressQosSchedPlcy, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

The value of the object sapIntendedEgressIpFilterId indicates the index in the tIPFilterTable corresponding to the Egress IP filter scheduler that should be applied on this SAP. If it deviates from sapCurrentEgressIpFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

The value of the object sapIntendedEgressIpv6FilterId indicates the index in the tIPv6FilterTable corresponding to the Egress IPv6 filter scheduler that should be applied on this SAP. If it deviates from sapCurrentEgressIpv6FilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

The value of the object sapIntendedEgressMacFilterId indicates the index in the tMacFilterTable corresponding to the Egress mac filter scheduler that should be applied on this SAP. If it deviates from sapCurrentEgressMacFilterId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

The value of the object sapIntendedEgressQosPolicyId indicates the index in the tSapEgressTable corresponding to the Egress Qos Policy that should be applied on this SAP. If it deviates from sapCurrentEgressQosPolicyId, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

The value of the object sapIntendedEgressQosSchedPlcy indicates the index in the tSapEgressTable corresponding to the Egress Qos Scheduler policy that should be applied on this SAP. If it deviates from sapCurrentEgressQosSchedPlcy, this means that there was a problem when trying to activate this filter. It can only deviate when using ToD Suites for the SAP. When the ToD Suites decides that a new filter must be applied, it will try to do this. If it fails, the current and intended field are not equal.

A table that contains Ingress Qos policy related statistics for a SAP. Conceptual rows in this table are automatically created by the system. No row will be created for a SAP if the value of the object sapTodSuite is equal to the empty string.

Statistics about a specific Ingress Qos Policy applied on a specific SAP.

The value of the object sapIgQosPlcyId indicates the row index in the tSapIngressTable corresponding to this ingress QoS policy, or one if no policy is specified.

The value of the object sapIgQosPlcyDroppedHiPrioPackets indicates the number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of the object sapIgQosPlcyDroppedHiPrioOctets indicates the number of high priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of the object sapIgQosPlcyDroppedLoPrioPackets indicates the number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of the object sapIgQosPlcyDroppedLoPrioOctets indicates the number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of the object sapIgQosPlcyForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the ingress Qchip.

The value of the object sapIgQosPlcyForwardedInProfOctets indicates the number of in-profile octets (rate below CIR) forwarded by the ingress Qchip.

The value of the object sapIgQosPlcyForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip.

The value of the object sapIgQosPlcyForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip.

A table that contains Egress Qos policy related statistics for a SAP. Conceptual rows in this table are automatically created by the system. No row will be created for a SAP if the value of the object sapTodSuite is equal to the empty string.

Statistics about a specific Egress Qos Policy applied on a specific SAP.

The value of the object sapEgQosPlcyId indicates the row index in the tSapEgressTable corresponding to this egress QoS policy, or one if no policy is specified.

The value of the object sapEgQosPlcyDroppedInProfPackets indicates the number of in-profile packets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of the object sapEgQosPlcyDroppedInProfOctets indicates the number of in-profile octets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of the object sapEgQosPlcyDroppedOutProfPackets indicates the number of out-profile packets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of the object sapEgQosPlcyDroppedOutProfOctets indicates the number of out-profile octets, as determined by the SAP egress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of the object sapEgQosPlcyForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the egress Qchip.

The value of the object sapEgQosPlcyForwardedInProfOctets indicates the number of in-profile octets (rate below CIR) forwarded by the egress Qchip.

The value of the object sapEgQosPlcyForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip.

The value of the object sapEgQosPlcyForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip.

A table that contains ingress QoS queue SAP statistics, per Ingress QoS Policy the queue was used by. Conceptual rows in this table are automatically created by the system. No row will be created for a SAP if the value of the object sapTodSuite is equal to the empty string.

Ingress statistics about a specific SAPs QoS queue for a given Qos policy.

The value of the object sapIgQosPlcyQueuePlcyId indicates the row index in the tSapIngressTable corresponding to this ingress QoS policy.

The index of the ingress QoS queue of this SAP used by the policy indicated by sapIgQosPlcyQueuePlcyId.

The value of sapIgQosPlcyQueueStatsOfferedHiPrioPackets indicates the number of high priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The value of sapIgQosPlcyQueueStatsDroppedHiPrioPackets indicates the number of high priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of sapIgQosPlcyQueueStatsOfferedLoPrioPackets indicates the number of low priority packets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The value of sapIgQosPlcyQueueStatsDroppedLoPrioPackets indicates the number of low priority packets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of sapIgQosPlcyQueueStatsOfferedHiPrioOctets indicates the number of high priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The value of sapIgQosPlcyQueueStatsDroppedHiPrioOctets indicates the number ofhigh priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of sapIgQosPlcyQueueStatsOfferedLoPrioOctets indicates the number of low priority octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip.

The value of sapIgQosPlcyQueueStatsDroppedLoPrioOctets indicates the number of low priority octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of sapIgQosPlcyQueueStatsForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the ingress Qchip.

The value of sapIgQosPlcyQueueStatsForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip.

The value of sapIgQosPlcyQueueStatsForwardedInProfOctets indicates the number of in-profile octets (rate below CIR) forwarded by the ingress Qchip.

The value of sapIgQosPlcyQueueStatsForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip.

The value of the object sapIgQosPlcyQueueCustId indicates the Customer ID for the associated service.

The value of sapIgQosPlcyQueueStatsUncoloredPacketsOffered indicates the number of uncolored packets offered to the ingress Qchip.

The value of sapIgQosPlcyQueueStatsUncoloredOctetsOffered indicates the number of uncolored octets offered to the ingress Qchip.

A table that contains egress QoS queue SAP statistics per Egress QoS Policy the queue was used by. Conceptual rows in this table are automatically created by the system. No row will be created for a SAP if the value of the object sapTodSuite is equal to the empty string.

Egress statistics about a specific SAPs QoS queue for a given Qos policy.

The row index in the tSapEgressTable corresponding to this egress QoS policy.

The value of sapEgQosPlcyQueueId indicates index of the egress QoS queue of this SAP.

The value of sapEgQosPlcyQueueStatsForwardedInProfPackets indicates the number of in-profile packets (rate below CIR) forwarded by the egress Qchip.

The value of sapEgQosPlcyQueueStatsDroppedInProfPackets indicates the number of in-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of sapEgQosPlcyQueueStatsForwardedOutProfPackets indicates the number of out-of-profile packets (rate above CIR) forwarded by the egress Qchip.

The value of sapEgQosPlcyQueueStatsDroppedOutProfPackets indicates the number out-of-profile packets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of sapEgQosPlcyQueueStatsForwardedInProfOctets indicates the number ofin-profile octets (rate below CIR) forwarded by the egress Qchip.

The value of sapEgQosPlcyQueueStatsDroppedInProfOctets indicates the number in-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of sapEgQosPlcyQueueStatsForwardedOutProfOctets indicates the number of out-of-profile octets (rate above CIR) forwarded by the egress Qchip.

The value of sapEgQosPlcyQueueStatsDroppedOutProfOctets indicates the number out-of-profile octets discarded by the egress Qchip due to: MBS exceeded, buffer pool limit exceeded, etc.

The value of the object sapEgQosPlcyQueueCustId indicates the Customer ID for the associated service.

sapDhcpInfoTable contains DHCP information related to a routed CO subscriber SAP. This table complements sapBaseInfoTable, and contains an entry for each routed CO subscriber SAP. Rows in this table are created and deleted automatically by the system.

DHCP specific information for a routed CO subscriber SAP.

The value of the object sapDhcpOperLeasePopulate indicates the number of DHCP lease states currently allocated on this SAP.

A table that contains ingress QoS queue statistics for the SAPs, organized by scheduler policy. Conceptual rows in this table are automatically created by the system. No row will be created for a SAP if the value of the object sapTodSuite is equal to the empty string.

Statistics about a specific SAPs ingress Qos Scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies.

The number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

The number of forwarded octets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

A table that contains egress QoS scheduler statistics for the SAPs, organized by scheduler policy. Conceptual rows in this table are automatically created by the system. No row will be created for a SAP if the value of the object sapTodSuite is equal to the empty string.

Statistics about a specific SAPs egress QoS scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies.

The number of packets forwarded by the egress Qchip, as determined by the SAP egress scheduler policy.

The number of octets forwarded by the egress Qchip, as determined by the SAP egress scheduler policy.

The sapIngSchedPlcyPortStatsTable contains ingress QoS scheduler statistics for the SAPs, organized per scheduler policy and per port. This table is used when the SAP is a CCAG or LAG in link mode, or an APS. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies. Conceptual rows in this table are automatically created by the system. No row will be created for a SAP if the value of the object sapTodSuite is equal to the empty string.

Statistics about a specific SAPs ingress Qos Scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies.

The value of sapIngSchedPlcyPortStatsPort is used as an index of the ingress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in link mode, this object is the TmnxPortID of the member-port on which the scheduler is applied.

The value of sapIngSchedPlcyPortStatsFwdPkt indicates the number of forwarded packets, as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

The value of sapIngSchedPlcyPortStatsFwdOct indicates the number of forwarded octets,as determined by the SAP ingress scheduler policy, offered by the Pchip to the Qchip.

The sapEgrSchedPlcyPortStatsTable contains egress QoS scheduler statistics for the SAPs, organized per scheduler policy and per port. This table is used when the SAP is a CCAG or LAG in link mode, or an APS. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies. Conceptual rows in this table are automatically created by the system. No row will be created for a SAP if the value of the object sapTodSuite is equal to the empty string.

Statistics about a specific SAPs egress Qos Scheduler. Entries are created when a scheduler policy of a SAP is replaced with another one due to Time-Of-Day policies.

The value of sapEgrSchedPlcyPortStatsPort is used as an index of the egress QoS scheduler of this SAP. When the SAP is an aps/ccag/lag in link mode, this object is the TmnxPortID of the member-port on which the scheduler is applied.

The value of sapEgrSchedPlcyPortStatsFwdPkt indicates the number of forwarded packets, as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip.

The value of sapEgrSchedPlcyPortStatsFwdOct indicates the number of forwarded octets,as determined by the SAP egress scheduler policy, offered by the Pchip to the Qchip.

A table that contains CEM SAP information.

Information about a specific CEM SAP.

The value of the object sapCemLastMgmtChange indicates the value of sysUpTime at the time of the most recent management-initiated change to this CEM SAP information.

This object indicates the CEM SAP endpoint type.

This object indicates the bit-rate in multiples of 64 Kbit/s of the CEM SAP.

This object indicates the CAS trunk framing mode of the CEM SAP.

This object specifies the payload size (in bytes) of packets transmitted to the Packet Service Network (PSN) by the CEM SAP. This determines the size of the data that will be transmitted over the service. As well, if the size of the data received is not consistent with the payload size then the packet is considered malformed. The default value depends on the CEM SAP endpoint type (sapCemEndpointType), and if applicable, the number of timeslots (sapCemBitrate): --------------------------------------------------------- | Endpoint Type | Timeslots | Default payload size | ---------------------+-----------+----------------------- | unstructuredE1 | n/a | 256 bytes | ---------------------+-----------+----------------------- | unstructuredT1 | n/a | 192 bytes | ---------------------+-----------+----------------------- | unstructuredE3 | n/a | 1024 bytes | ---------------------+-----------+----------------------- | unstructuredT3 | n/a | 1024 bytes | ---------------------+-----------+----------------------- | nxDS0 (E1/T1) | N = 1 | 64 bytes | | +-----------+----------------------- | | N = 2..4 | N x 32 bytes | | +-----------+----------------------- | | N = 5..15 | N x 16 bytes | | +-----------+----------------------- | | N >= 16 | N x 8 bytes | ---------------------+-----------+----------------------- | nxDS0WithCas (E1)| N | N x 16 bytes | ---------------------+-----------+----------------------- | nxDS0WithCas (T1)| N | N x 24 bytes | --------------------------------------------------------- For nxDS0WithCas, the sapCemPayloadSize cannot be changed away from the default value. For 1xDS0, sapCemPayloadSize must be a multiple of 2. For NxDS0, where N > 1, sapCemPayloadSize must be a multiple of the number of timeslots (sapCemBitrate). For unstructuredE1, unstructuredT1, unstructuredE3 and unstructuredT3, sapCemPayloadSize must be a multiple of 32 bytes. Configuring sapCemPayloadSize and sapCemJitterBuffer to values that result in less than 2 packet buffers or greater than 32 packet buffers is not allowed. For all endpoint types except for nxDS0WithCas, the minimum payload size is given below: --------------------------------------------------------- | Endpoint Type | Timeslots | Minimum payload size | ---------------------+-----------+----------------------- | unstructuredE1 | n/a | 256 bytes | ---------------------+-----------+----------------------- | unstructuredT1 | n/a | 192 bytes | ---------------------+-----------+----------------------- | unstructuredE3 | n/a | 1024 bytes | ---------------------+-----------+----------------------- | unstructuredT3 | n/a | 1024 bytes | ---------------------+-----------+----------------------- | nxDS0 (E1) | N = 1..4 | N x 16 bytes | ---------------------+-----------+----------------------- | nxDS0 (T1) | N = 1..4 | N x 24 bytes | ---------------------+-----------+----------------------- | nxDS0 (E1/T1) | N = 5..15 | N x 16 bytes | | +-----------+----------------------- | | N >= 16 | N x 8 bytes | ---------------------+-----------+----------------------- For all endpoints types except for nxDS0WithCas, the maximum payload size is 2048 bytes. Setting this object to 0 sets it back to the default value.

This object specifies the jitter buffer size in milliseconds (ms). Default value depends on the CEM SAP endpoint type (sapCemEndpointType), and if applicable, the number of timeslots (sapCemBitrate): --------------------------------------------------------- | Endpoint Type | Timeslots | Default jitter buf. | ---------------------+-----------+----------------------- | unstructuredE1 | n/a | 5 ms | ---------------------+-----------+----------------------- | unstructuredT1 | n/a | 5 ms | ---------------------+-----------+----------------------- | unstructuredE3 | n/a | 5 ms | ---------------------+-----------+----------------------- | unstructuredT3 | n/a | 5 ms | ---------------------+-----------+----------------------- | nxDS0 (E1/T1) | N = 1 | 32 ms | | +-----------+----------------------- | | N = 2..4 | 16 ms | | +-----------+----------------------- | | N = 5..15 | 8 ms | | +-----------+----------------------- | | N >= 16 | 5 ms | ---------------------+-----------+----------------------- | nxDS0WithCas (E1)| N | 8 ms | ---------------------+-----------+----------------------- | nxDS0WithCas (T1)| N | 12 ms | --------------------------------------------------------- Configuring sapCemPayloadSize and sapCemJitterBuffer to values that result in less than 2 packet buffers or greater than 32 packet buffers is not allowed. The valid range is 1 to 250 ms. Setting this object to 0 sets it back to the default value.

This object specifies whether a RTP header is used when packets are transmitted to the Packet Service Network (PSN) by the CEM SAP.

This object specifies whether this CEM SAP is in differential mode.

This object specifies the value of the differential timestamp frequency in multiples of 8 KHz for this CEM SAP.

The value of sapCemReportAlarm determines when and if to generate notifications for the CEM SAP.

The value of sapCemReportAlarmStatus indicates the current alarms on this CEM SAP.

The value of the object sapCemLocalEcid specifies the local ECID. Only valid if CEM SAP belongs to an EPIPE service.

The value of the object sapCemRemoteMacAddr specifies the remote MAC address. Only valid if CEM SAP belongs to an EPIPE service.

The value of the object sapCemRemoteEcid specifies the remote ECID. Only valid if CEM SAP belongs to an EPIPE service.

This value indicates the jitter buffer length in number of packet buffers.

This value indicates the playout buffer packets threshold in number of packet buffers.

A table that contains CEM SAP statistics.

Statistics for a specific CEM SAP.

The value of sapCemStatsIngressForwardedPkts indicates the number of packets that were successfully forwarded.

The value of sapCemStatsIngressDroppedPkts indicates the total number of packets that were dropped due to errors.

The value of sapCemStatsEgressForwardedPkts indicates the number of packets that were successfully forwarded.

The value of sapCemStatsEgressDroppedPkts indicates the total number of packets that were dropped due to errors.

The value of sapCemStatsEgressMissingPkts indicates the number of missing packets (as detected via control word sequence number gaps).

The value of sapCemStatsEgressPktsReOrder indicates the number of packets detected out of sequence (via control word sequence number), but successfully re-ordered.

The value of sapCemStatsEgressJtrBfrUnderruns indicates the number of times a packet needed to be played out and the jitter buffer was empty.

The value of sapCemStatsEgressJtrBfrOverruns indicates the number of times a packet was dropped because it could not fit in the jitter buffer.

The value of sapCemStatsEgressMisOrderDropped indicates the number of packets detected out of order (via control word sequence numbers), and could not be re-ordered, or could not be placed in the jitter buffer because it was out of the current window.

The value of sapCemStatsEgressMalformedPkts indicates the number of packets detected with unexpected size, or bad headers stack.

The value of sapCemStatsEgressLBitDropped indicates the number of packets dropped due to the L bit set by the far end.

The value of sapCemStatsEgressMultipleDropped indicates the number of packets dropped due to multiple sequence numbers.

The value of sapCemStatsEgressESs indicates the number of Error Seconds (ESs) encountered. Any malformed packet, seq. error, LOPS and similar are considered as error seconds.

The value of sapCemStatsEgressSESs indicates the number of Severely Error Seconds (SESs) encountered. This is when more than 30 percent of the packets within a one second window are missing.

The value of sapCemStatsEgressUASs indicates the number of Unavailable Seconds (UASs) encountered. Any consecutive ten seconds of SESs are counted as one UAS.

The value of sapCemStatsEgressFailureCounts indicates the number failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared.

The value of sapCemStatsEgressUnderrunCounts indicates the number of times the jitter buffer went into an underrun state.

The value of sapCemStatsEgressOverrunCounts indicates the number of times the jitter buffer went into an overrun state.

The value of sapCemStatsEgressJtrBfrDepth indicates the current packet depth of the jitter buffer.

A table that contains SAP Layer 2 Protocol Tunneling Statistics. This table complements sapTlsInfoTable. Rows in this table are created and deleted automatically by the system.

Layer 2 Protocol Tunneling Statistics for a specific SAP. The statistics are provided for each combination of Destination Address and LLC SNAP type.

The value of sapTlsL2ptStatsLastClearedTime indicates the last time that these stats were cleared. The value zero indicates that they have not been cleared yet.

The value of sapTlsL2ptStatsL2ptEncapStpConfigBpdusRx indicates the number of L2PT encapsulated STP config bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapStpConfigBpdusTx indicates the number of L2PT encapsulated STP config bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsL2ptEncapStpRstBpdusRx indicates the number of L2PT encapsulated STP rst bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapStpRstBpdusTx indicates the number of L2PT encapsulated STP rst bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsL2ptEncapStpTcnBpdusRx indicates the number of L2PT encapsulated STP tcn bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapStpTcnBpdusTx indicates the number of L2PT encapsulated STP tcn bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsL2ptEncapPvstConfigBpdusRx indicates the number of L2PT encapsulated PVST config bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapPvstConfigBpdusTx indicates the number of L2PT encapsulated PVST config bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsL2ptEncapPvstRstBpdusRx indicates the number of L2PT encapsulated PVST rst bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapPvstRstBpdusTx indicates the number of L2PT encapsulated PVST rst bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsL2ptEncapPvstTcnBpdusRx indicates the number of L2PT encapsulated PVST tcn bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapPvstTcnBpdusTx indicates the number of L2PT encapsulated PVST tcn bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsStpConfigBpdusRx indicates the number of STP config bpdus received on this SAP.

The value of sapTlsL2ptStatsStpConfigBpdusTx indicates the number of STP config bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsStpRstBpdusRx indicates the number of STP rst bpdus received on this SAP.

The value of sapTlsL2ptStatsStpRstBpdusTx indicates the number of STP rst bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsStpTcnBpdusRx indicates the number of STP tcn bpdus received on this SAP.

The value of sapTlsL2ptStatsStpTcnBpdusTx indicates the number of STP tcn bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsPvstConfigBpdusRx indicates the number of PVST config bpdus received on this SAP.

The value of sapTlsL2ptStatsPvstConfigBpdusTx indicates the number of PVST config bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsPvstRstBpdusRx indicates the number of PVST rst bpdus received on this SAP.

The value of sapTlsL2ptStatsPvstRstBpdusTx indicates the number of PVST rst bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsPvstTcnBpdusRx indicates the number of PVST tcn bpdus received on this SAP.

The value of sapTlsL2ptStatsPvstTcnBpdusTx indicates the number of PVST tcn bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsOtherBpdusRx indicates the number of other bpdus received on this SAP.

The value of sapTlsL2ptStatsOtherBpdusTx indicates the number of other bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsOtherL2ptBpdusRx indicates the number of other L2PT bpdus received on this SAP.

The value of sapTlsL2ptStatsOtherL2ptBpdusTx indicates the number of other L2PT bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsOtherInvalidBpdusRx indicates the number of other invalid bpdus received on this SAP.

The value of sapTlsL2ptStatsOtherInvalidBpdusTx indicates the number of other invalid bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsL2ptEncapCdpBpdusRx indicates the number of L2PT encapsulated CDP bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapCdpBpdusTx indicates the number of L2PT encapsulated CDP bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsL2ptEncapVtpBpdusRx indicates the number of L2PT encapsulated VTP bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapVtpBpdusTx indicates the number of L2PT encapsulated VTP bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsL2ptEncapDtpBpdusRx indicates the number of L2PT encapsulated DTP bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapDtpBpdusTx indicates the number of L2PT encapsulated DTP bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsL2ptEncapPagpBpdusRx indicates the number of L2PT encapsulated PAGP bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapPagpBpdusTx indicates the number of L2PT encapsulated PAGP bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsL2ptEncapUdldBpdusRx indicates the number of L2PT encapsulated UDLD bpdus received on this SAP.

The value of sapTlsL2ptStatsL2ptEncapUdldBpdusTx indicates the number of L2PT encapsulated UDLD bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsCdpBpdusRx indicates the number of CDP bpdus received on this SAP.

The value of sapTlsL2ptStatsCdpBpdusTx indicates the number of CDP bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsVtpBpdusRx indicates the number of VTP bpdus received on this SAP.

The value of sapTlsL2ptStatsVtpBpdusTx indicates the number of VTP bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsDtpBpdusRx indicates the number of DTP bpdus received on this SAP.

The value of sapTlsL2ptStatsDtpBpdusTx indicates the number of DTP bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsPagpBpdusRx indicates the number of PAGP bpdus received on this SAP.

The value of sapTlsL2ptStatsPagpBpdusTx indicates the number of PAGP bpdus transmitted on this SAP.

The value of sapTlsL2ptStatsUdldBpdusRx indicates the number of UDLD bpdus received on this SAP.

The value of sapTlsL2ptStatsUdldBpdusTx indicates the number of UDLD bpdus transmitted on this SAP.

A table that contains Ethernet SAP information.

Information about a specific Ethernet SAP.

sapEthernetLLFAdminStatus specifies whether or not Link- Loss Forwarding is enabled (up). When this object is set to up the underlying port will be forced into the operationally down state if the service is operationally down, or any of the sdpBindPwPeerStatusBits are set, and will set the underlying ports tmnxPortEtherReasonDownFlags linklossFwd bit. Setting this object to down will clear the linklossFwd reason. sapEthernetLLFAdminStatus can only be enabled on saps configured for an EPIPE service using an Ethernet port with the tmnxPortEncapType set to nullEncap.

sapEthernetLLFOperStatus indicates whether or not the underlying port is forced operationally down due to the service being operationally down or an sdpBindPwPeerStatusBits bit is set. sapEthernetLLFOperStatus is set to fault when the sapEthernetLLFAdminStatus is set to up, and either a fault has occurred on the pseudo-wire, or the service is down, otherwise sapEthernetLLFOperStatus is set to clear.

The msapPlcyTable has an entry for each managed SAP(MSAP) policy configured in the system.

Each entry represents the configuration for a managed SAP(MSAP) policy. The values for each entry will be used to populate the following tables when the MSAP policy is applied to a MSAP: TIMETRA-SAP-MIB::sapBaseInfoTable TIMETRA-SAP-MIB::sapSubMgmtInfoTable

The value of msapPlcyName specifies the name of the MSAP policy.

The value of msapPlcyRowStatus is used for the creation and deletion of MSAP policies.

The value of msapPlcyLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

The value of msapPlcyDescription specifies the description of the MSAP policy.

The value of msapPlcyCpmProtPolicyId specifies a CPM Protection policy for the MSAP policy. If a corresponding policy is not defined in TIMETRA-SECURITY-MIB::tmnxCpmProtPolTable, an inconsistentValue error will be returned. A value of 254 specifies that the default CPM Protection policy is associated with the Managed SAP. This object is not supported on SR-1 and ESS-1, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is 5, and 7710, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is 7 or 9. An attempt to set msapPlcyCpmProtPolicyId to a non-zero value on one of these unsupported chassis types will return an inconsistentValue error.

The value of msapPlcyCpmProtMonitorMac specifies whether the tmnxCpmProtPolPerSrcRateLimit of the CPM Protection policy, as specified by msapPlcyCpmProtPolicyId, must be applied. If the value of msapPlcyCpmProtMonitorMac is true, the per-source rate limit must be applied. If the value of msapPlcyCpmProtPolicyId is equal to zero, the value of msapPlcyCpmProtMonitorMac is irrelevant and will be ignored. This object is not supported on SR-1 and ESS-1, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is 5, and 7710, where the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is 7 or 9. An attempt to set msapPlcyCpmProtMonitorMac to true on one of these unsupported chassis types will return an inconsistentValue error.

The value of msapPlcySubMgmtDefSubId specifies what will be used as the default subscriber identification applicable on the MSAP. This value is used in case no other source (like Radius) provides a subscriber identification string. If the value of this object is set to useSapId, the SAP-id will be used as the default subscriber identification string. In this case, msapPlcySubMgmtDefSubIdStr must contain the empty string, so any non-empty string in msapPlcySubMgmtDefSubIdStr will be set to an empty string. If the value of this object is set to useAutoId, the auto-generated subscriber identification string, as defined in tmnxSubMgmtAutoSubIdObjs, is used as the default subscriber identification string. In this case, msapPlcySubMgmtDefSubIdStr must contain the empty string, so any non-empty string in msapPlcySubMgmtDefSubIdStr will be set to an empty string. If the value of this object is set to useString, the value of msapPlcySubMgmtDefSubIdStr will be used as the default subscriber identification string. In this case, an empty msapPlcySubMgmtDefSubIdStr means that there is no default subscriber identification configured.

The value of msapPlcySubMgmtDefSubIdStr specifies the default subscriber identification string applicable on this MSAP.

The value of msapPlcySubMgmtDefSubProfile specifies the default subscriber profile applicable on the MSAP. If a corresponding profile is not defined in tmnxSubProfileTable, an inconsistentValue error will be returned. A value of default is not allowed for this object.

The value of msapPlcySubMgmtDefSlaProfile specifies the default SLA profile applicable on the MSAP. If a corresponding profile is not defined in tmnxSLAProfileTable, an inconsistentValue error will be returned.

The value of msapPlcySubMgmtDefAppProfile specifies the default application profile applicable on the MSAP. If a corresponding profile is not defined in TIMETRA-BSX-NG-MIB::tmnxBsxAppProfTable, an inconsistentValue error will be returned.

The value of msapPlcySubMgmtSubIdPlcy specifies the subscriber identification policy applicable on the MSAP. If a corresponding profile is not defined in tmnxSubIdentPolicyTable, an inconsistentValue error will be returned.

The value of msapPlcySubMgmtSubscriberLimit specifies the maximum number of subscribers allowed for the MSAP. A value is 0 means there is no limit. The values for the objects msapPlcySubMgmtProfiledTrafOnly, msapPlcySubMgmtNonSubTrafSubProf, and msapPlcySubMgmtNonSubTrafSlaProf are only meaningful when the value of msapPlcySubMgmtSubscriberLimit is 1 and will not be used when the value of msapPlcySubMgmtSubscriberLimit is not 1.

The value of msapPlcySubMgmtProfiledTrafOnly specifies whether only profiled traffic is applicable for the MSAP. If set to true, the MSAP queues will be deleted. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1.

The value of msapPlcySubMgmtNonSubTrafSubId specifies the subscriber identification applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1.

The value of msapPlcySubMgmtNonSubTrafSubProf specifies the subscriber profile applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1.

The value of msapPlcySubMgmtNonSubTrafSlaProf specifies the SLA profile applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1.

The value of msapPlcySubMgmtNonSubTrafAppProf specifies the Application profile applicable on the MSAP for all non-subscriber traffic. The value of this object is only meaningful if msapPlcySubMgmtSubscriberLimit is set to 1.

The value of msapPlcyAssociatedMsaps indicates the number of MSAPs associated with this MSAP policy.

The value of msapPlcySubMgmtDefInterDestId specifies what will be used as the default intermediate destination identifier applicable on the MSAP. This value is used in case no other source (like Radius) provides an intermediate destination identifier. If the value of this object is set to useString, the value of msapPlcySubMgmtDefInterDestIdStr will be used as the default intermediate destination identifier. In this case, an empty msapPlcySubMgmtDefInterDestIdStr means that there is no default intermediate destination identifier configured. If the value of this object is set to useTopQTag, the top q-tag of the MSAP will be used as the default intermediate destination identifier. In this case, msapPlcySubMgmtDefInterDestIdStr must contain the empty string. If the value of this object is set to useVpi, the ATM VPI of the MSAP will be used as the default intermediate destination identifier. In this case, msapPlcySubMgmtDefInterDestIdStr must contain the empty string.

The value of msapPlcySubMgmtDefSubIdStr specifies the default subscriber identification string applicable on this MSAP.

The value of msapPlcyIgmpTrkExpiryTime specifies the time in seconds that this system continues to track an inactive host. The value zero specifies that the value must be set to the actual value of the object svcIgmpTrkExpiryTime of the service an MSAP belongs to.

The value of the object msapPlcyIgmpTrkImportPlcy specifies the policy statement that must be applied to all incoming IGMP messages on the MSAP.

The value of the object msapPlcyIgmpTrkMaxNbrGrps specifies how many group addresses are allowed for the MSAP. The value 0 means that no limit is imposed.

The value of the object msapPlcyIgmpTrkMaxNbrSrcs specifies how many source addresses are allowed per group address for the MSAP. The value 0 means that no limit is imposed.

The value of msapPlcySubMgmtDefFilterProfile specifies the default filter profile applicable on the MSAP. The specified filter profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubFilterProfileTable.

The msapTlsPlcyTable has an entry for each managed SAP (MSAP) policy configured in the system.

Each entry represents the VPLS-related configuration for a managed SAP (MSAP) policy. The values for each entry will be used to populate the following VPLS-related tables when the MSAP policy is applied to a MSAP: TIMETRA-SAP-MIB::sapTlsInfoTable TIMETRA-SAP-MIB::sapTlsDhcpInfoTable ALCATEL-IGMP-SNOOPING-MIB::tlsIgmpSnpgConfigTable

The value of msapTlsPlcyLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

The value of msapTlsPlcySplitHorizonGrp specifies the name of the split-horizon group for the MSAP. If the name specified does not correspond to a tlsShgInfoEntry for the VPLS service, the creation of the MSAP will fail. Additionally, if msapTlsPlcySplitHorizonGrp is set to a new value, the sapSplitHorizonGrp object for any existing MSAPs created by this policy will not be updated.

The value of msapTlsPlcyArpReplyAgent specifies the status of the special ARP response mechanism in the system for ARP requests destined to static or dynamic hosts associated with the MSAP. disabled - the ARP reply function is not operational enabled - the ARP reply function is enabled without subscriber identification. enabledWithSubscrIdent - the ARP reply function is enabled with subscriber identification.

The value of msapTlsPlcySubMgmtMacDaHashing specifies whether subscriber traffic egressing a LAG MSAP has its egress LAG link selected by a function of the MAC destination address instead of subscriber id.

The value of msapTlsPlcyDhcpLeasePopulate specifies the maximum number of DHCP lease states allowed on the MSAP.

The value of msapTlsPlcyDhcpPrxyAdminState specifies the desired administrative state of the proxy server on the interface.

The value of msapTlsPlcyDhcpPrxyServAddrType specifies the address type of msapTlsPlcyDhcpPrxyServAddr.

The value of msapTlsPlcyDhcpPrxyServAddr specifies the IP address of the which will be used as the source address of the emulated DHCP server in the context of the VPLS MSAP. This address is mandatory for the proxy server capability and it should be in the context of the subnet represented by the VPLS.

The value of msapTlsPlcyDhcpPrxyLeaseTime specifies, in seconds, how long a DHCP client is allowed to use the offered IP address. A value of 0 means the lease time provided by a RADIUS or an upstream DHCP server will not be overridden. A value of 7 days (315446399 seconds) is used when RADIUS does not provide a lease time.

The value of msapTlsPlcyDhcpPrxyLTRadOverride specifies whether or not the lease time provided by the RADIUS server is presented to the DHCP client. By default the proxy-server will always make use of msapTlsPlcyDhcpPrxyLeaseTime, regardless of what lease time information is provided from the RADIUS server. When msapTlsPlcyDhcpPrxyLTRadOverride is set to true, the proxy-server will use the lease time information provided by the RADIUS server, regardless of the configured lease time.

The value of msapTlsPlcyDhcpInfoAction specifies the DHCP option reforwarding policy: replace - replace existing information with configured information drop - discard messages with existing relay information if the option-82 information is also present keep - retain the existing relay information

The value of msapTlsPlcyDhcpCircuitId specifies whether or not the circuit-id suboption is present, and if it is present what information goes in it: none - the circuit-id suboption will not be part of the information option (Option 82). asciiTuple - the ASCII-encoded concatenated tuple consisting of the - access-node-identifier - service-id - interface-name is used. vlanAsciiTuple - the format will include VLAN-id and dot1p bits in addition to what is included in ascii-tuple already. The format is supported on dot1q and qinq encapsulated ports only. Thus, when the option 82 bits are stripped, dot1p bits will be copied to the Ethernet header of an outgoing packet.

The value of msapTlsPlcyDhcpRemoteId specifies what information goes into the remote-id suboption in the DHCP Relay packet. If the value of this object is set to none, the remote-id suboption will not be part of the information option (Option 82). If the value of this object is set to mac, the MAC address of the remote end is encoded in the suboption. If the value of this object is set to remote-id, msapTlsPlcyDhcpRemoteIdString will represent the remote-id. By default, the remote-id value is none.

The value of msapTlsPlcyDhcpRemoteIdString specifies the remote-id. The value of this object is ignored if msapTlsPlcyDhcpRemoteId does not have the value of remote-id.

The value of msapTlsPlcyDhcpVendorInclOpts specifies what is encoded in the Alcatel-Lucent vendor specific sub-option of option 82. The value of this object is only used when msapTlsPlcyDhcpInfoAction is replace.

The value of msapTlsPlcyDhcpVendorOptStr specifies the string that goes into the Alcatel-Lucent vendor specific sub-option of option 82. This string is only used when msapTlsPlcyDhcpInfoAction is set to replace.

The value of msapTlsPlcyEgressMcastGroup specifies the Egress Multicast Group for the MSAP.

The value of msapTlsPlcyIgmpSnpgImportPlcy specifies the policy statement that is be applied to all incoming IGMP messages on the MSAP.

The value of msapTlsPlcyIgmpSnpgFastLeave specifies whether fast leave is allowed on this MSAP. If set to enabled, the system prunes the port on which an IGMP leave message has been received without waiting for the Group Specific Query to timeout.

The value of msapTlsPlcyIgmpSnpgSendQueries specifies whether the system generates General Queries by itself on the MSAP.

The value of msapTlsPlcyIgmpSnpgGenQueryIntv specifies the interval (in seconds) between two consecutive general queries sent by the system on the MSAP. The value of this object is only meaningful when the value of msapTlsPlcyIgmpSnpgSendQueries is enabled.

The value of msapTlsPlcyIgmpSnpgQueryRespIntv specifies the maximum response time (in seconds) advertised in IGMPv2/v3 queries. The value of this object is only meaningful when the value of msapTlsPlcyIgmpSnpgSendQueries is enabled.

The value of msapTlsPlcyIgmpSnpgRobustCount specifies the robustness variable on the MSAP. This object allows tuning for the expected packet loss on the MSAP. If a MSAP is expected to be lossy, the Robustness Variable may be increased. IGMP snooping is robust to (Robustness Variable-1) packet losses. The value of this object is only meaningful when the value of msapTlsPlcyIgmpSnpgSendQueries is enabled.

The value of msapTlsPlcyIgmpSnpgLastMembIntvl specifies the Max Response Time (in tenths of a second) used in Group-Specific and Group-Source-Specific Queries sent in response to leave messages. This is also the amount of time between Group-Specific Query messages. This value may be tuned to modify the leave latency of the network. A reduced value results in reduced time to detect the loss of the last member of a group.

The value of msapTlsPlcyIgmpSnpgMaxNbrGrps specifies how many group addresses are allowed for the MSAP. The value 0 means that no limit is imposed.

The value of msapTlsPlcyIgmpSnpgMvrFromVplsId specifies from which VPLS the multicast streams corresponding to the groups learned via the MSAP are copied. Groups which cannot be joined to the corresponding MVR VPLS (because MVR is not up or the configured MVR policy rejects the group) copy the multicast streams from the local VPLS if IGMP snooping is up (i.e. tlsIgmpSnpgCfgAdminState is enabled).

The value of msapTlsPlcyIgmpSnpgVersion specifies the version of IGMP running on the MSAP.

The value of msapTlsPlcyIgmpSnpgMcacPlcyName specifies the name of the multicast CAC (Connection Admission Control) policy.

The value of msapTlsPlcyIgmpSnpgMcacUncnstBW specifies the bandwidth assigned for interfaces multicast CAC policy traffic in kilo-bits per second(kbps). If the default value of -1 is set, there is no constraint on bandwidth allocated at the interface. If the value of msapTlsPlcyIgmpSnpgMcacUncnstBW is set to 0 and if a multicast CAC policy is assigned on the interface, then no group (channel) from that policy is allowed on that interface.

The value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW specifies the bandwidth pre-reserved for all the mandatory channels on a given interface in kilo-bits per second(kbps). If the value of msapTlsPlcyIgmpSnpgMcacUncnstBW is 0, no mandatory channels are allowed. If the value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW is -1, then all mandatory and optional channels are allowed. If the value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW is equal to the value of msapTlsPlcyIgmpSnpgMcacUncnstBW, then all the unconstrained bandwidth on a given interface is allocated to mandatory channels configured through multicast CAC policy on that interface and no optional groups (channels) are allowed. The value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW should always be less than or equal to that of msapTlsPlcyIgmpSnpgMcacUncnstBW. An attempt to set the value of msapTlsPlcyIgmpSnpgMcacPrRsvMnBW greater than that of msapTlsPlcyIgmpSnpgMcacUncnstBW will result in inconsistentValue error.

The value of msapTlsPlcyArpHostMaxNumHosts specifies the maximum number of ARP hosts allowed on the TLS MSAP.

The value of msapTlsPlcyArpHostMinAuthIntvl specifies the minimum interval between two consecutive authentication attempts for the same ARP host.

The msapIgmpSnpgMcacLevelTable has an entry for each multicast CAC policy constraint level configured for a Managed SAP policy.

Each row entry represents a multicast CAC policy bundle level constraints for a particular Managed SAP policy. Entries are created and deleted by the user.

The value of msapIgmpSnpgMcacLevelId indicates the level id of the multicast CAC policy bundle constraint. The value of level 1 has the highest priority and level 8 the lowest.

The value of msapIgmpSnpgMcacLevelRowStatus is used for creation and deletion of level constraint in a CAC for a Managed SAP policy.

The value of msapIgmpSnpgMcacLevelLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

The value of msapIgmpSnpgMcacLevelBW specifies the bandwidth in kilo-bits per second (kbps) for the level.

The msapIgmpSnpgMcacLagTable has an entry for each lag port configured for a multicast CAC policy bundle configured for a Managed SAP policy.

Each row entry represents a particular multicast CAC lag port constraints for a Managed SAP policy.. Entries are created and deleted by the user.

The value of msapIgmpSnpgMcacLagPortsDown indicates the configured number of ports in a lag group that are down. If the number of ports available in the lag is reduced by the number of ports configured for msapIgmpSnpgMcacLagPortsDown object then bandwidth allowed for bundle will be updated to the value of msapIgmpSnpgMcacLevelBW indexed by msapIgmpSnpgMcacLagLevel value.

The value of msapIgmpSnpgMcacLagRowStatus is used for creation and deletion of lag constraint in a CAC policy.

The value of msapIgmpSnpgMcacLagLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

The value of msapIgmpSnpgMcacLagLevel specifies the level id to use when the value of msapIgmpSnpgMcacLagPortsDown matches the actual number of ports down in a lag. Using the value of msapIgmpSnpgMcacLagLevel as an index, the operational MSAP unconstrained bandwidth will be set to msapIgmpSnpgMcacLevelBW. By default, for all lag constraints the link level will be set to 1 at row creation.

A table that contains Managed SAP information.

Information about a specific Managed SAP.

The value of msapInfoCreationSapPortEncapVal indicates the port encapsulation value of the SAP with a sapSubType value of capture that created this MSAP.

The value of msapInfoCreationPlcyName indicates the value of the msapPlcyName object for MSAP policy used to create this MSAP.

The value of msapInfoReEvalPolicy specifies whether to re-apply the Managed SAP policy associated with this MSAP. When a SET of this object is done with a value of doAction, the system will attempt to re-apply the MSAP policy indicated by msapInfoCreationPlcyName. If this action is successful, noError will be returned. If this action is unsuccessful, an inconsistentValue error will be returned. Attempting to SET this object with a value of notApplicable will have no effect and will return noError. SNMP GET and GETNEXT requests on this object will return notApplicable.

The value of msapInfoLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local network management subsystem, then this object contains a zero value.

A table that contains statistics for SAPs with a sapSubType value of capture.

Statistics for a specific capture SAP.

The value of msapCaptureSapStatsTriggerType indicates the type of trigger packets this entry is for.

The value of msapCaptureSapStatsPktsRecvd indicates the number of packets received on this capture SAP.

The value of msapCaptureSapStatsPktsRedirect indicates the number of packets redirected on this capture SAP.

The value of msapCaptureSapStatsPktsDropped indicates the number of packets dropped on this capture SAP.

The sapTlsMrpTable augments sapTlsInfoTable with attributes of the Multiple Registration Protocol (MRP) feature for the TLS SAP.

MRP specific information about a SAP in a TLS.

The value of sapTlsMrpRxPdus indicates the number of MRP packets received on this SAP.

The value of sapTlsMrpDroppedPdus indicates the number of dropped MRP packets on this SAP.

The value of sapTlsMrpTxPdus indicates the number of MRP packets transmitted on this SAP.

The value of sapTlsMrpRxNewEvent indicates the number of New MRP events received on this SAP.

The value of sapTlsMrpRxJoinInEvent indicates the number of Join-In MRP events received on this SAP.

The value of sapTlsMrpRxInEvent indicates the number of In MRP events received on this SAP.

The value of sapTlsMrpRxJoinEmptyEvent indicates the number of Join Empty MRP events received on this SAP.

The value of sapTlsMrpRxEmptyEvent indicates the number of Empty MRP events received on this SAP.

The value of sapTlsMrpRxLeaveEvent indicates the number of Leave MRP events received on this SAP.

The value of sapTlsMrpTxNewEvent indicates the number of New MRP events transmitted on this SAP.

The value of sapTlsMrpTxJoinInEvent indicates the number of Join-In MRP events transmitted on this SAP.

The value of sapTlsMrpTxInEvent indicates the number of In MRP events transmitted on this SAP.

The value of sapTlsMrpTxJoinEmptyEvent indicates the number of Join Empty MRP events transmitted on this SAP.

The value of sapTlsMrpTxEmptyEvent indicates the number of Empty MRP events transmitted on this SAP.

The value of sapTlsMrpTxLeaveEvent indicates the number of Leave MRP events transmitted on this SAP.

This table contains an entry for each MAC address managed by Multiple MAC Registration Protocol (MMRP) on the SAP for the TLS. Entries are dynamically created and destroyed by the system as the MAC Addresses are registered or declared in MMRP.

MMRP specific information about a MAC address managed by MMRP on a SAP in a TLS.

The value of sapTlsMmrpMacAddr indicates an ethernet MAC address which is being managed by MMRP on this SAP.

The value of sapTlsMmrpDeclared indicates whether the MRP applicant on this SAP is declaring this MAC address on behalf of MMRP.

The value of sapTlsMmrpRegistered indicates whether the MRP registrant on this SAP has notified MMRP of a registration of this MAC address.

The value of sapTlsMmrpEndStation indicates whether the MRP registrant on this SAP is registered per end station.

The sapIngQosHsmdaQueueTable has an entry for each Hsmda SAP-level ingress queue override configured on the system. This table is obsoleted in 10.0 release.

Each row entry represents a Hsmda SAP-level ingress queue override record. Entries are created and deleted via SNMP SET operations on sapIngQosHsmdaQueueRowStatus.

The value of sapIngQosHsmdaQueueId index specifies the Hsmda egress queue which this override record will affect.

The value of sapIngQosHsmdaQueueRowStatus specifies...

The value of sapIngQosHsmdaQueueLastChanged indicates the sysUpTime at the time of the most recent management-initiated change to this table row.

The value of sapIngQosHsmdaQueueAdminPIR specifies the PIR rate in kbps allowed for this Hsmda ingress queue.

The value of sapIngQosHsmdaQueueAdminCIR specifies the CIR rate in kbps allowed for this Hsmda ingress queue.

The value of sapIngQosHsmdaQueueSlopePolicy specifies the slope policy that defines the RED slopes for this Hsmda ingress queue.

A table that contains ingress QoS HSMDA queue SAP statistics. This table is obsoleted in 10.0 release.

Ingress statistics about a specific SAPs QoS HSMDA queue.

The value of sapIngHsmdaQStatCustId indicates the customer ID for the statistics.

The value of sapIngHsmdaQStatHiPktsDropped indicates the number of high-priority packets dropped on ingress on this SAP.

The value of sapIngHsmdaQStatLoPktsDropped indicates the number of low-priority packets dropped on ingress on this SAP.

The value of sapIngHsmdaQStatHiOctsDropped indicates the number of high-priority octets dropped on ingress on this SAP.

The value of sapIngHsmdaQStatLoOctsDropped indicates the number of low-priority octets dropped on ingress on this SAP.

The value of sapIngHsmdaQStatInProfPktsFwd indicates the number of in-profile packets forwarded on ingress on this SAP.

The value of sapIngHsmdaQStatOutProfPktsFwd indicates the number of out-of-profile packets forwarded on ingress on this SAP.

The value of sapIngHsmdaQStatInProfOctsFwd indicates the number of out-of-profile packets forwarded on ingress on this SAP.

The value of sapIngHsmdaQStatOutProfOctsFwd indicates the number of out-of-profile packets forwarded on ingress on this SAP.

The value of sapIngHsmdaQStatAllPktsOffered indicates the total number of packets offered on ingress on this SAP.

The value of sapIngHsmdaQStatAllOctsOffered indicates the total number of octets offered on ingress on this SAP.

A table that contains ingress QoS HSMDA counter SAP statistics. This table is obsoleted in 10.0 release.

Ingress statistics about a specific SAPs QoS HSMDA counter.

The value of sapIngHsmdaCntrStCntrId indicates the counter ID for the statistics.

The value of sapIngHsmdaCntrStCustId indicates the customer ID for the statistics.

The value of sapIngHsmdaCntrStHiPktDrop indicates the number of high-priority packets dropped for the ingress counter, specified by the index sapIngHsmdaCntrStCntrId, on this SAP.

The value of sapIngHsmdaCntrStLoPktDrop indicates the number of low-priority packets dropped for the ingress counter, specified by the index sapIngHsmdaCntrStCntrId, on this SAP.

The value of sapIngHsmdaCntrStHiOctDrop indicates the number of high-priority octets dropped for the ingress counter, specified by the index sapIngHsmdaCntrStCntrId, on this SAP.

The value of sapIngHsmdaCntrStLoOctDrop indicates the number of low-priority octets dropped for the ingress counter, specified by the index sapIngHsmdaCntrStCntrId, on this SAP.

The value of sapIngHsmdaCntrStInProfPktFwd indicates the number of in-profile packets forwarded for the ingress counter, specified by the index sapIngHsmdaCntrStCntrId, on this SAP.

The value of sapIngHsmdaCntrStOutProfPktFwd indicates the number of out-of-profile packets forwarded for the ingress counter, specified by the index sapIngHsmdaCntrStCntrId, on this SAP.

The value of sapIngHsmdaCntrStInProfOctFwd indicates the number of out-of-profile packets forwarded for the ingress counter, specified by the index sapIngHsmdaCntrStCntrId, on this SAP.

The value of sapIngHsmdaCntrStOutProfOctFwd indicates the number of out-of-profile packets forwarded for the ingress counter, specified by the index sapIngHsmdaCntrStCntrId, on this SAP.

The value of sapIngHsmdaCntrStAllPktOffered indicates the total number of packets offered on ingress on this SAP.

The value of sapIngHsmdaCntrStAllOctOffered indicates the total number of octets offered on ingress on this SAP.

The sapEgrQosHsmdaQueueTable has an entry for each Hsmda SAP-level egress queue override configured on the system.

Each row entry represents a Hsmda SAP-level egress queue override record. Entries are created and deleted via SNMP SET operations on sapEgrQosHsmdaQueueRowStatus.

The value of sapEgrQosHsmdaQueueId index specifies the Hsmda egress queue which this override record will affect.

The value of sapEgrQosHsmdaQueueRowStatus controls the creation and deletion of rows in this table.

The value of sapEgrQosHsmdaQueueLastChanged indicates the sysUpTime at the time of the most recent management-initiated change to this table row.

The value of sapEgrQosHsmdaQueueAdminPIR specifies the PIR rate in kbps allowed for this Hsmda ingress queue.

The value of sapEgrQosHsmdaQueueAdminCIR specifies the CIR rate in kbps allowed for this Hsmda ingress queue. This object is obsoleted in 10.0 Release.

The value of sapEgrQosHsmdaQueueSlopePolicy specifies the slope policy that defines the RED slopes for this Hsmda ingress queue.

The value of sapEgrQosHsmdaQueueWrrWeight specifies the weighted round-robin weight override for the given egress hsmda queue on this SAP. When set to default value, the weighted round-robin weight is not overridden and the weighted round-robin weight from the sap-egress qos policy is honored. When a non-default value is given, that is used instead of the weighted round-robin weight given in the sap-egress policy.

The value of sapEgrQosHsmdaQueueMBS specifies the maximum buffer space (MBS) override in bytes for the given egress hsmda queue on this SAP. When set to default value, the MBS is not overridden and the MBS from the sap-egress qos policy is honored. When a non-default value is given, that is used instead of the MBS given in the sap-egress policy.

A table that contains egress QoS HSMDA queue SAP statistics.

Egress statistics about a specific SAPs QoS HSMDA queue.