TIARA-HSSI-MIB: View SNMP OID List / Download MIB

VENDOR: TASMAN NETWORKS


 Home MIB: TIARA-HSSI-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, SNMPv2-TC, TIARA-NETWORKS-SMI

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 tiaraHssiMib 1.3.6.1.4.1.3174.2.7.2
MIB definitions for Tiara HSSI modules.
     hssiConfigTable 1.3.6.1.4.1.3174.2.7.2.1 no-access
The HSSI interface configurable parameters are listed in this table.
         hssiConfigTableEntry 1.3.6.1.4.1.3174.2.7.2.1.1 no-access
HSSI table entry.
             hssiIfIndex 1.3.6.1.4.1.3174.2.7.2.1.1.1 integer no-access
An integer value that is an index in the entries of the ifTable (MIB-II) with a HSSI interface type.
             hssiConfigClockRate 1.3.6.1.4.1.3174.2.7.2.1.1.2 integer32 read-write
Configures the clock rate (in Hertz) for the HSSI interface.
             hssiConfigClockSource 1.3.6.1.4.1.3174.2.7.2.1.1.3 integer read-write
Configures the clock source for the HSSI interface to either internal or line. Enumeration: 'line': 2, 'internal': 1.
             hssiConfigTxClockSource 1.3.6.1.4.1.3174.2.7.2.1.1.4 integer read-write
Configures the transmit clock source for the HSSI interface to either internal or terminal. This variable is valid only for the HSSI interface on the USSI card. Enumeration: 'normalinternal': 1, 'invertedinternal': 3, 'normalterminal': 2, 'invertedterminal': 4.
             hssiConfigRxClockSource 1.3.6.1.4.1.3174.2.7.2.1.1.5 integer read-write
Configures the receive clock source for the HSSI interface to either internal or terminal. This variable is valid only for the HSSI interface on the USSI card Enumeration: 'normalinternal': 1, 'invertedinternal': 3, 'normalterminal': 2, 'invertedterminal': 4.
             hssiConfigMode 1.3.6.1.4.1.3174.2.7.2.1.1.6 integer read-write
Configures the mode for the HSSI to either DCE or DTE. Enumeration: 'dce': 1, 'dte': 2.
             hssiConfigDataMode 1.3.6.1.4.1.3174.2.7.2.1.1.7 integer read-write
Configures the data mode for the HSSI interface. This variable is valid only for the HSSI interface on the USSI card. Enumeration: 'inverted': 2, 'normal': 1.
             hssiConfigCRC 1.3.6.1.4.1.3174.2.7.2.1.1.8 integer read-write
Configures the cyclic redundancy check for the HSSI interface to either 16 or 32 bits. Enumeration: 'crc32': 2, 'crc16': 1.
             hssiConfigProcessCtrlSignal 1.3.6.1.4.1.3174.2.7.2.1.1.9 integer read-write
Configures the processing of control signals (CA/TA) for the HSSI interface. This variable is valid only for the HSSI interface on the USSI card. Enumeration: 'ignore': 1, 'process': 2.
             hssiDteLoopback 1.3.6.1.4.1.3174.2.7.2.1.1.10 truthvalue read-write
Configures the local DTE for loopback operation: TRUE : request local DTE to go into line loopback FALSE : request local DTE to abandon line loopback These commands are valid only if the HSSI adaptor is in DCE mode and connected to a local DTE. Since the local DTE has a greater loopback priority than the local DCE, a loopback request initiated by the DCE will be ignored if the DTE simultaneously requests the DCE to loopback. Similarly, the DTE will abort a loopback already initiated by the DCE when the DTE requests the DCE to loopback.
             hssiDceLoopbackTest 1.3.6.1.4.1.3174.2.7.2.1.1.11 integer read-write
Configures the local/remote DCE for loopback operation. Three DCE loopback modes are available: line, cable, and remote. Use noTest to abandon any of the DCE loopbacks. If the DCE is already in any one of the loopback modes, then noTest must be issued to abort the current test before initiating another loopback request. These commands are valid only if the HSSI adaptor is in DTE mode and it connected to a DCE. Enumeration: 'line': 2, 'remote': 4, 'cable': 3, 'noTest': 1.
     hssiTraps 1.3.6.1.4.1.3174.2.7.2.2
         hssiTrapVariables 1.3.6.1.4.1.3174.2.7.2.2.1
             hssiAlarmType 1.3.6.1.4.1.3174.2.7.2.2.1.1 integer no-access
Specifies the type of alarm generated by the agent for the HSSI interface. Alarms are mode dependent; they are interpreted as follows: hssi-alarms-CA - CA not received from DCE (HSSI is DTE) hssi-alarms-ST - HSSI adaptor driving ST (HSSI is DCE) hssi-alarms-TM - TM received from DCE (HSSI is DTE) hssi-alarms-LC - HSSI adaptor detects LC (HSSI is DTE) hssi-alarms-LC - HSSI adaptor driving LC (HSSI is DCE) hssi-alarms-TA - TA not received from DTE (HSSI is DCE) hssi-alarms-LALB - HSSI adaptor detects LA and/or LB (HSSI is DCE) hssi-alarms-LALB - HSSI adaptor driving LA and/or LB (HSSI is DTE) Enumeration: 'hssi-alarm-TA': 5, 'hssi-alarm-TM': 3, 'hssi-alarm-ST': 2, 'hssi-alarm-LALB': 6, 'hssi-alarm-CA': 1, 'hssi-alarm-LC': 4.
     hssiStatsTable 1.3.6.1.4.1.3174.2.7.2.3 no-access
The HSSI interface status parameters are listed in this table.
         hssiStatsTableEntry 1.3.6.1.4.1.3174.2.7.2.3.1 no-access
HSSI Statistics table entry.
             hssiStatsAlarmStatus 1.3.6.1.4.1.3174.2.7.2.3.1.1 bits read-only
Specifies the status of the HSSI alarm. If the particular bit is set, then it indicates that the alarm is in ON state. Alarm bits are mode dependent; they are interpreted as follows: hssi-alarms-CA - CA not received from DCE (HSSI is DTE) hssi-alarms-ST - HSSI adaptor driving ST (HSSI is DCE) hssi-alarms-TM - TM received from DCE (HSSI is DTE) hssi-alarms-LC - HSSI adaptor detects LC (HSSI is DTE) hssi-alarms-LC - HSSI adaptor driving LC (HSSI is DCE) hssi-alarms-TA - TA not received from DTE (HSSI is DCE) hssi-alarms-LALB - HSSI adaptor detects LA and/or LB (HSSI is DCE) hssi-alarms-LALB - HSSI adaptor driving LA and/or LB (HSSI is DTE) Bits: 'hssi-alarms-TM': 3, 'hssi-alarms-LALB': 6, 'hssi-alarms-LC': 4, 'hssi-alarms-ST': 2, 'hssi-alarms-TA': 5, 'hssi-alarms-CA': 1, 'hssi-no-alarms': 0.
             hssiStatsFramesIn 1.3.6.1.4.1.3174.2.7.2.3.1.2 counter32 read-only
Specifies the number of incoming frames.
             hssiStatsFramesOut 1.3.6.1.4.1.3174.2.7.2.3.1.3 counter32 read-only
Specifies the number of outgoing frames.
             hssiStatsOctetsIn 1.3.6.1.4.1.3174.2.7.2.3.1.4 counter32 read-only
Specifies the number of incoming octets.
             hssiStatsOctetsOut 1.3.6.1.4.1.3174.2.7.2.3.1.5 counter32 read-only
Specifies the number of outgoing octets.
             hssiStatsCRCErrors 1.3.6.1.4.1.3174.2.7.2.3.1.6 counter32 read-only
Specifies the number of CRC errors that have been identified.
           hssiAlarmOnTrap 1.3.6.1.4.1.3174.2.7.2.20.1
HSSI alarm traps for the Alarm-On state.
           hssiAlarmOffTrap 1.3.6.1.4.1.3174.2.7.2.20.2
HSSI alarm traps for the Alarm-Off state.