SLE-MLSQOS-MIB: View SNMP OID List / Download MIB

This MIB contains all informations about ML QOS supported features.

Enable / Disable MlQos enable (1) disable (0)

Global incoming Cos to outgoing Cos mapping.

Global incoming Cos to outgoing queue mapping.

Global incoming dscp to outgoing dscp mapping.

Global incoming dscp to outgoing queue mapping.

Global incoming exp to outgoing exp mapping.

Global incoming exp to outgoing queue mapping.

Queues with Strict scheduling

Queue weight for Weighted round robin scheduling. If the queue wt is given 0, then the queue becomes strict queue

Rate limiting for CPU. Defines Max packets per second to CPU

weight for Cpu Queues

node Rate limiting for CPU. Defines Max packets per second to CPU

node weight for Cpu Queues

Exp - to - class mapping

Hqos has feature to disable or enable statistics so this object is only applicable when hqos is enabled

qos phb-priority-color Ex: PHB Name | Priority Color ------------------------------------------- be | 0 red cs0 | 0 green cs1 | 1 green af11 | 1 yellow af12 | 1 red af13 | 0 green cs2 | 2 green af21 | 2 green af22 | 2 yellow af23 | 2 red cs3 | 3 green af31 | 4 red af32 | 3 green af33 | 3 yellow cs4 | 4 green af41 | 5 yellow af42 | 5 red af43 | 4 green cs5 | 5 green ef | 6 red cs6 | 6 yellow cs7 | 7 green

Default Class to DSCP Ex: QoS PHB map to DSCP: PHB Name | dscp ------------------------------------------- be | 0 be | 0 cs1 | 9 af11 | 10 af12 | 12 af13 | 14 cs2 | 16 af21 | 18 af22 | 20 af23 | 22 cs3 | 24 af31 | 26 af32 | 28 af33 | 30 cs4 | 32 af41 | 34 af42 | 35 af43 | 38 cs5 | 40 ef | 46 cs6 | 48 cs7 | 56

qos default cos to class trust Ex:QoS Cos+Cfi/DEI to CLASS: COS CFI/DEI | CLASS ------------------------------------------- 0 0 | cs0 0 1 | cs0 1 0 | cs1 1 1 | cs1 2 0 | cs2 2 1 | cs2 3 0 | cs3 3 1 | cs3 4 0 | cs4 4 1 | cs4 5 0 | cs5 5 1 | cs5 6 0 | cs6 6 1 | cs6 7 0 | cs7 7 1 | cs7

qos Default cos to class no trust Ex: QoS Cos+Cfi/DEI to CLASS: COS CFI/DEI | CLASS ------------------------------------------- 0 0 | be 0 1 | be 1 0 | be 1 1 | be 2 0 | be 2 1 | be 3 0 | be 3 1 | be 4 0 | be 4 1 | be 5 0 | be 5 1 | be 6 0 | be 6 1 | be 7 0 | be 7 1 | be

qos default dscp to class trust Ex: QoS Dscp to CLASS: DSCP | CLASS ------------------------------------------- 0 | be 1 | be 2 | be 3 | be 4 | be 5 | be 6 | be 7 | be 8 | cs1 9 | be 10 | af11 11 | be 12 | af12 13 | be 14 | af13 15 | be 16 | cs2 17 | be 18 | af21 19 | be 20 | af22 21 | be 22 | af23 23 | be 24 | cs3 25 | be 26 | af31 27 | be 28 | af32 29 | be 30 | af33 31 | be 32 | cs4 33 | be 34 | af41 35 | be 36 | af42 37 | be 38 | af43 39 | be 40 | cs5 41 | be 42 | be 43 | be 44 | be 45 | be 46 | ef 47 | be 48 | cs6 49 | be 50 | be 51 | be 52 | be 53 | be 54 | be 55 | be 56 | cs7 57 | be 58 | be 59 | be 60 | be 61 | be 62 | be 63 | be

qos defualt dscp to class no trust Ex: QoS Dscp to CLASS: DSCP | CLASS ------------------------------------------- 0 | be 1 | be 2 | be 3 | be 4 | be 5 | be 6 | be 7 | be 8 | be 9 | be 10 | be 11 | be 12 | be 13 | be 14 | be 15 | be 16 | be 17 | be 18 | be 19 | be 20 | be 21 | be 22 | be 23 | be 24 | be 25 | be 26 | be 27 | be 28 | be 29 | be 30 | be 31 | be 32 | be 33 | be 34 | be 35 | be 36 | be 37 | be 38 | be 39 | be 40 | be 41 | be 42 | be 43 | be 44 | be 45 | be 46 | be 47 | be 48 | be 49 | be 50 | be 51 | be 52 | be 53 | be 54 | be 55 | be 56 | be 57 | be 58 | be 59 | be 60 | be 61 | be 62 | be 63 | be

The configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'setMlQosStatus': 1, 'unSetMlsQosWrr': 7, 'setMlsQosNodeCpuRate': 10, 'setMlsQosWrr': 6, 'setMlsQosNodeCpuQueueWt': 11, 'unsetHQosStatistics': 13, 'setHQosStatistics': 12, 'setMlsQosCpuRate': 8, 'setMlsQosCpuQueueWt': 9, 'setMlsQosStrictQueue': 4, 'unSetMlsQosMapping': 3, 'unSetMlsQosStrictQueue': 5, 'setMlsQosMapping': 2.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

Enable / Disable MlQos enable (1) disable (0)

Below Mapping Types can be configured cosToCos(1), cosToQueue(2), dscpToDscp(3), dscpToQueue(4), expToExp(5), expToQueue(6) expToClass(7)

Ingress or incoming mapping values. Based on sleMlsQosGlobalControlMappingType, this value has to be set. Ex. If sleMlsQosGlobalControlMappingType = cosToCos, then sleMlsQosGlobalControlMappingIngValue = Incoming or ingress COS value

Egress or outgoing mapping values. Based on sleMlsQosGlobalControlMappingType, this value has to be set. Ex. If sleMlsQosGlobalControlMappingType = cosToCos, then sleMlsQosGlobalControlMappingEgrValue = outgoing or egress COS value

Queue Id

Queue weight for weighted round robin scheduling. This value is set for the Queue Id configured via sleMlsQosGlobalControlQueueId

Rate limiting for CPU. Defines Max packets per second to CPU This value is set for the Queue Id configured via sleMlsQosGlobalControlQueueId

Weight for CPU Queue. This value is set for the Queue Id configured via sleMlsQosGlobalControlQueueId

Node Id

Egress or outgoing mapping value is only for exp to class Diffserv class alias, eg: be, ef, af11 etc. If sleMlsQosGlobalControlMappingType is exp-to-class, this value has to be set. Ex. If sleMlsQosGlobalControlMappingType = exp-to-class, then sleMlsQosGlobalControlMappingEgrValue = outgoing or egress class value

Aggrgegate Policy Table

Police index

Police Name

Traffic Rate configured for the Aggregate police profile

Burst Size configured for the Aggregate police profile

the configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'deleteAggrPolice': 2, 'createAggrPolice': 1.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

Aggregator Police Name

Traffic Rate configured for the Aggrgegate Police profile

Traffic Rate configured for the Aggrgegate Police profile

Index for the table. This is a running index number, which will be generated internally

Filter Index for the table. This is a running index number, which will be generated internally

Access Control List Num. <1-99> standard access list <100-199> extended access list <1300-1999> standard access list (expanded range) <2000-2699> extended access list (expanded range) Name of the access list

ACL MATCH Type mac (1), EthType(2), l3Proto (3)

ACL Actions deny(0) deny the packets permit(1) permit. remark(2) mark the packets

ACL ethertype to be matched. ip4(0) ipv4 packets ip6(1) ipv6 packets. mpls(3) mpls packets

ACL protocols to be matched. 0-255 : IANA protocol numbers 256 - any Some important protocol Numbers GRE - 47 IGMP -2 IPV4 - 4 IPComp - 108 OSPF - 89 RSVP - 46 PIM - 103 VRRP - 112

Src Ip Address

DST Address

SRC Address Mask

DST Address Mask

Src MAC Address

DST MAC Address

SRC Address Mask

DST Address Mask

TCP/UDP Src port action 0 - no-action 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range

TCP/UDP Dst port action 0 - no-action 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range

TCP/UDP Src port .

TCP/UDP Dst port .

Exact Match

Remark Description

The object is used to display the ICMP type of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1

The object is used to display the ICMP code of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1

End port for TCP/UDP source port range.

End port for TCP/UDP destination port range.

the configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'unSetExtenAclMatchTcpUdp': 10, 'setAclNameSrcIp': 11, 'unSetExtenAclMatchEthType': 6, 'setAclWithActionRemark': 13, 'setExtenAclMatchEthType': 5, 'setExtenAclMatchL3Proto': 7, 'setExtenAclMatchMac': 3, 'unSetAclNameSrcIp': 12, 'setExtenAclMatchTcpUdp': 9, 'unSetStandAclMatchSrcIp': 2, 'unSetExtenAclMatchMac': 4, 'unSetAclWithActionRemark': 14, 'unSetExtenAclMatchL3Proto': 8, 'setStandAclMatchSrcIp': 1.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

Access Control List Name. <1-99> standard access list <100-199> extended access list <1300-1999> standard access list (expanded range) <2000-2699> extended access list (expanded range) Name for the access list

ACL Match Types mac (1), EthType(2), l3Proto (3)

ACL Actions deny(0) deny the packets permit(1) Permit packets remark(2) mark the packets

ACL MAC ethertype to be matched. WORD Ethertype value - (0x600-0xffff) ip4 IPv4 Ethertype - 0x0800 ip6 IPv6 Ethertype - 0x86dd mpls MPLS Ethertype - 0x8847

ACL protocols to be matched. 0-255 : IANA protocol numbers 256 - any Some important protocol Numbers GRE - 47 IGMP -2 IPV4 - 4 IPComp - 108 OSPF - 89 RSVP - 46 PIM - 103 VRRP - 112

ACL SrcAddress. 1. MAC address 2. IP Address 3. Any

ACL SrcAddress. 1. MAC address 2. IP Address 3. Any

ACL Src Addr Mask. 1. MAC address 2. IP Address

ACL dst Addr Mask. 1. MAC address 2. IP Address

TCP/UDP Port Action to be matched. 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range

TCP/UDP Port Action to be matched. 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range

TCP/UDP Src port to be matched.

TCP/UDP Dst port to be matched.

Configure Exact Match for Name

Configure remark description

The object is used to set the ICMP type of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1

The object is used to set the ICMP code of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1

End port for TCP/UDP Src port range to be matched.

End port for TCP/UDP Dst port range to be matched.

Index for the table. Class Map name

Class map Match criteria : Cos value

Class map Match criteria : Inner Cos value

Class map Match criteria : Engress Interface

Class map Match criteria : Eth Type

Class map Match criteria : Src Ip Address

Class map Match criteria : dst Ip Address

Class map Match criteria : Src Ip Mask Length

Class map Match criteria : Dst Ip Mask Length

Class map Match criteria : Src Ip Address

Class map Match criteria : dst Ip Address

Class map Match criteria : Src Ip Mask Length

Class map Match criteria : Dst Ip Mask Length

Class map Match criteria : DSCP value

Class map Match criteria : Ip Precedence

Class map Match criteria : Ip6 DSCP value

Class map Match criteria : ip6 Precedence value

Class map Match criteria : TCP src Port

Class map Match criteria : TCP Dst Port

Class map Match criteria : TCP src Port Range

Class map Match criteria : TCP Dst Port Range

Class map Match criteria : UDP src Port

Class map Match criteria : UDP Dst Port

Class map Match criteria : UDP src Port

Class map Match criteria : UDP Dst Port

Class map Match criteria : Src MAC Addr

Class map Match criteria : Src MAC Addr Mask

Class map Match criteria : Dst MAC Addr

Class map Match criteria : Dst MAC Addr Mask

Class map Match criteria : Vlan Id

Class map Match criteria : Vlan Id Range

Class map Match criteria : Inner Vlan Id

Class map Match criteria : Vlan TPID

Class map Match criteria : Acl Name

Class map Match criteria : Layer4 Any Src Port

Class map Match criteria : Layer4 Any Dst Port

Class map Match criteria : Layer4 Any src Port range

Class map Match criteria : Layer4 Any Dst Port range

This object is used to set the Class map match criteria, to map the matchAll or MatchAny for HQS. Enumeration: 'matchAll': 1, 'matchAny': 2, 'noMatch': 0.

the configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'unSetClassMapMatchVlanTpid': 14, 'unSetClassMapMatchIpAddr': 10, 'unSetClassMapMatchAccessGroup': 16, 'createClassMap': 1, 'setClassMapMatchIpAddr': 9, 'deleteClassMap': 2, 'setClassMapMatch': 3, 'unSetClassMapMatchMac': 12, 'setClassMapMatchRange': 5, 'unSetClassMapMatchEgressIntf': 18, 'setClassMapMatchVlanTpid': 13, 'unSetClassMapMatch': 4, 'setClassMapMatchEgressIntf': 17, 'setClassMapMatchAccessGroup': 15, 'unSetClassMapMatchRange': 6, 'setClassMapMatchMac': 11, 'setClassMapMatchEtherType': 7, 'unSetClassMapMatchEtherType': 8.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

Class Map name

Class Map Type cos (1) , innerCos(2), ipDscp (3), ipPrecedence (4), ip6Dscp (5), ip6Precedence (6), tcpSrcPort (7), tcpDstPort (8), udpSrcPort (9), udpDstPort (10), VlanId (11), innerVlanId (12), layer4SrcPort (13), layer4DstPort (14)

Class Map match Value

Class Map Type tcpSrcPort (1), tcpDstPort (2), udpSrcPort (3), udpDstPort (4), VlanId (5), layer4SrcPort (6), layer4DstPort (7)

Class Map match Value: Low

Class Map match Value : High

Class map Match criteria : Eth Type

Class Map Src Type 1. IPv4 2. IPv6 3. Mac Enumeration: 'mac': 3, 'ipv4': 1, 'ipv6': 2.

Class map Match criteria : Src Address. It can be IPV4 / IPV6 / MAC

Class map Match criteria : dst Ip Address it can be IPV4 / IPV6 / MAC

Class map Match criteria : Src Ip Mask Length

Class map Match criteria : Dst Ip Mask Length

Class map Match criteria : Src MAC Addr Mask

Class map Match criteria : Dst MAC Addr Mask

Class map Match criteria : ACL Group List

Class map Match criteria : vlan TDID

Class map Match criteria : egress interface. This can be CPU, interface Name, Vlan Interface

This object is used to set the Class map match criteria, to map the matchAll or MatchAny for HQS. Enumeration: 'matchAll': 1, 'matchAny': 2.

Policy Map name

Class map Name

Priority low(0) medium(1) high(2) highest(3)

Operation Mode Enumeration: 'none': 0, 'deny': 2, 'allow': 1.

Police Type srtcm(1) trtcm(2)

Police CIR (committed ingress rate) value

Police PIR (peak ingress rate) value

Police CBS (committed burst size) value

Police EBS (Excess burst size) value

Exceed Action Type none (0) drop (1) set-dscp-transmit (2) set-tos-transmit (3) set-cos-transmit (4) transmit (7)

Exceed Action COS

Exceed Action DSCP

Exceed Action TOS

Violate Action Type none(0) drop(1) set-dscp-transmit(2) set-cos-transmit(3) set-tos-transmit(4) transmit(5)

Violate Action Value

Agrregate Police name:

Action Type: deny

Cos value

cpy Cos value.

Ip DSCP value .

Ip6 DSCP value to be set.

Ip precedence value to be set.

Ip6 precedence value to be set.

Mirror to Port value.

redirect to Port value.

Vlan Id value.

Vlan COS value

Heirarchical qos policy-map qos-group. Max range is 1 to 2000.

Internal Queue Priority.

Copy to CPU.

the configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'setPolicyMapClassPolicer': 6, 'deletePolicyMapClass': 2, 'setPolicyMapClassSet': 10, 'deletePolicyMap': 12, 'setPolicyMapClassMatchPriority': 3, 'unSetPolicyMapClassPolicerAggregate': 9, 'setPolicyMapClassOperMode': 4, 'unSetPolicyMapClassSet': 11, 'createPolicyMapClass': 1, 'setPolicyMapClassPolicerAggregate': 8, 'unSetPolicyMapClassPolicer': 7, 'unSetPolicyMapClassOperMode': 5.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

Index for the table. Class Map name

Class map Name

Priority low(0) medium(1) high(2) highest(3)

Operation Mode Enumeration: 'none': 0, 'deny': 2, 'allow': 1.

Police Type srtcm(1) trtcm(2)

Police CIR (committed ingress rate) value

Police PIR (Peak ingress rate) value

Police CBS (Committed Burst size) value

Police EBS (Excess Burst size) value

Exceed Action Type none (0) drop (1) set-dscp-transmit (2) set-tos-transmit (3) set-cos-transmit (4) transmit (7)

Exceed Action COS

Exceed Action DSCP

Exceed Action TOS

Exceed Action Violate none(0) drop(1) set-dscp-transmit(2) set-cos-transmit(3) set-tos-transmit(4) transmit(5)

Exceed Action Violate Value

Aggregate Policy name: this is configured via sleMlsQosAggPoliceTable

Action Types: cos (1), cpu-cos (2), ip-dscp (3), ip-precedence (4), redirect-to-port (5), mirror-to-port (6), vlan (7), ip6-dscp (8), ip6-precedence (9), cpu-copy (10), deny (11), qos-group(12), none(13), queue(14), vlan-cos(15)

Cos value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as cos

cpy Cos value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as cpu-cos

Ip DSCP value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip-dscp

Ip6 DSCP value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip6-dscp

Ip precedence value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip-precedence

Ip6 precedence value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip6-precedence

Mirror to Port value. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To setthis value, sleMlsQosPolicyMapCtrlClassSetAction should be set as mirror-to-port

redirect to Port value. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To setthis value, sleMlsQosPolicyMapCtrlClassSetAction should be set as redirect-to-port

Vlan Id value. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as vlan

Vlan COS value

Heirarchical qos policy-map qos-group. Max range is 1 to 2000.

Internal Queue Priority.

Interface table

This Index is based on Max entries i.e. 64 (dscp)

Index for the table. Interface Name

Interface trust state none (0) cos (1) dscp (2)

Interface Cos value

Interface Cos override value

Interface Cos to cos mapping

Interface Cos to queue mapping

Interface DSCP values

Interface dscp to dscp mapping

Interface dscp to queue mapping

Interface exp to exp mapping

Interface Traffic Shaping rate

Interface traffic shaping burst

Interface policy map mapping

Interface trust pass-through COS enabled

Interface trust pass-through DSCP enabled

Interface cos to class mapping in no truct mode It represnet COS - CNG - CLASS

Interface dscp to class mapping in no truct mode It represnet DSCP - CLASS

To rewite the dscp/cos at egress in uniform mode. Enumeration: 'none': 0, 'cos': 1, 'dscp': 2.

Interface traffic IFG exclude 0 - No 1 - Yes

Interface traffic policing rate <8-1000000> in kbps

Interface traffic policing burst <2-2000>

the configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'unSetInterfaceInputPolicyMap': 6, 'setInterfaceInputPolicyMap': 5, 'setInterfaceQosMapping': 1, 'setInterfaceTrafficPolicingDot3x': 15, 'unSetInterfaceTrafficShaping': 4, 'setInterfaceOutputPolicyMap': 7, 'setInterfaceReplace': 11, 'unsetInterfaceTrafficIfgExclude': 14, 'setInterfaceTrafficShaping': 3, 'setInterfaceTrafficIfgExclude': 13, 'setInterfaceOveride': 9, 'unSetInterfaceQosMapping': 2, 'unSetInterfaceOutputPolicyMap': 8, 'unsetInterfaceOveride': 10, 'unsetInterfaceReplace': 12, 'unsetInterfaceTrafficPolicingDot3x': 16.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

Class map Name

Mapping Type: cos (1) Configure interface default CoS values cos-cos (2) Specify cos-cos cos-queue (3) Specify cos-queue map dscp (4) Set the default DSCP vlaue dscp-dscp(5) Specify dscp-dscp dscp-queue (6) DSCP-to-QUEUE exp-exp(7) Specify exp-exp trust (8) Configure port trust state trust-passthrough (9) COnfigure port trust pass-through state cosToClass (10) configure cos to class dscpToClass (11) configure dscp to class

Ingress or incoming mapping values. Based on sleMlsQosInterfaceCtrlMapingType, this value has to be set. Ex. If sleMlsQosInterfaceCtrlMapingType = cosToCos, then sleMlsQosInterfaceCtrlMapingIngVal = Incoming or ingress COS value

Egress or outgoing mapping values. Based on sleMlsQosInterfaceCtrlMapingType, this value has to be set. Ex. If sleMlsQosInterfaceCtrlMapingType = cosToCos, then sleMlsQosInterfaceCtrlMapingIngVal = Egress COS value

Interface COS override value

Interface trust state Trust: cos (1) dscp (2) Trust pass-through: pass-through cos (1) pass-through dscp (2)

Interface Traffic shape rate

Interface Traffic shape burst

Interface Policy Map mapping

Specify CNG value <0-1>

rewite the dscp/cos at egress in uniform mode. Enumeration: 'none': 0, 'cos': 1, 'dscp': 2.

This Index is based on no of Queues

This Index is based on no of Queues

Interface Queue Shape rate

Interface Queue WRR queue weight

Interface Queue WRR random detect min threshold

Interface Queue WRR random detect max threshold

Interface Queue WRR random detect exp weight

Interface Queue TailDrop threshold

Interface Strict Queue Config

WRR Random Detect Drop Start

WRR Random Detect Drop Slope

WRR Random Detect Color Enumeration: 'red': 2, 'yellow': 1.

Interface Queue Shape rate (minimum)

the configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'unSetQueueProfile': 2, 'setQueueProfile': 1.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

Queue Id

Queue Id

Interface Queue Rate

Interface Queue WRR Queue weight

Interface Queue WRR random detect Min Threshold

Interface Queue WRR random detect Max Threshold

Interface Queue WRR random detect exp weight

Interface Queue Taildrop Threshold

Interface Queue WRR Random Detect Drop Start

Interface Queue WRR Random Detect Drop Slope

Interface Queue WRR Random Detect Color Enumeration: 'red': 2, 'yellow': 1.

Interface Queue Rate(minimum)

Index for the table. QStats Name

This Index is based on Max entries i.e. 64 (dscp)

Wred Green drop packet counter

Wred yellow drop packet counter

Wred red drop packet counter

Taildrop drop packet counter

Taildrop drop bytes counter

Total out packets in the Queue

Total out bytes in the Queue

Total mcast out packets in the Queue

Total mcast out bytes in the Queue

Total drop packets in the Queue

Total drop bytes in the Queue

Total mcast drop packets in the Queue

Total mcast drop bytes in the Queue

Total Enqueued packets in the Queue

Total Enqueued bytes in the Queue

the configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'clearTailDropStats': 2, 'clearWredStats': 1, 'clearQueueStats': 3.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

Index for the table. Class Map name

Class map Name

This Table is used to show the information for Class Map queueing Table

This Table is used to show the information for Class Map queueing Table

Class Map queue name. An unique object identify an entry of this table.

This object is used to show the match group of the class map queueing.

the configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'setSleHqosClassMapQueueControlMatchGroup': 3, 'unsetSleHqosClassMapQueueControlMatchGroup': 4, 'deleteSleHqosClassMapQueueControlEntry': 2, 'createSleHqosClassMapQueueControlEntry': 1.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

This Object is used to the set the control name for the Class map queue Table

This object is used to set the match group of the class map queueing

This table is used to show the Policy mapping queue information of the policy map queueing

This table is used to show the Policy mapping queue information of the policy map queueing

This object identify an entry in this table.

This object is used to show the shape for the policy map queue Types: 1)average 1-1000000000(bps|kbps|mbps|gbps) 2)percent 1-100

This object is used to show the bandwidth for the policy map queue average 1-1000000000(bps|kbps|mbps|gbps) percent 1-100

This object is used to show the remained bandwidth for the policy map queue

This object is used to show the queue limit for the policy map queue

This object is used to show the service name for the policy map queue

This object is used to show the priority for the policy map queue Always value is 1

This object is used to show the random detuct minimum threshold for the policy map queue

This object is used to show the random detuct maximum threshold for the policy map queue

the configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'deletePolicyMapQueueEntry': 2, 'createPolicyMapQueueEntry': 1, 'unsetPolicyMapQueueServicePolicy': 6, 'setPolicyMapQueueRandomDetect': 7, 'unsetPolicyMapQueueParameters': 4, 'unsetPolicyMapQueueRandomDetect': 8, 'setPolicyMapQueueParameters': 3, 'setPolicyMapQueueServicePolicy': 5.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

This object is used to set the name for the policy map queue

This object is used to set the name for the policy map queue

This object is used to set 1)shape: the shape for the policy map queue is to configure shaping on an egress queue to impose a maximum rate on it 2)queue-limit: the Queue Limit is to configure tail drop by setting queue limits on both ingress and egress queues 3)bandwidth: To allocate a minimum percentage of the interface bandwidth to a queue 4)bandwidth-Remain: To configures the bandwidth remaining on the interface in a queue 5)Priority: To configure a single output queuing class as the priority queue average 1-1000000000(bps|kbps|mbps|gbps) limit 1-131072 (packets | bytes | kbytes) percent 1-100 Enumeration: 'priority': 5, 'bandwidthRemain': 4, 'shape': 1, 'queueLimit': 2, 'bandwidth': 3.

This object is used to set 1)shape: the shape for the policy map queue is to configure shaping on an egress queue to impose a maximum rate on it 2)queue-limit: the Queue Limit is to configure tail drop by setting queue limits on both ingress and egress queues 3)bandwidth: To allocate a minimum percentage of the interface bandwidth to a queue 4)bandwidth-Remain: To configures the bandwidth remaining on the interface in a queue 5)Priority: To configure a single output queuing class as the priority queue average 1-1000000000(bps|kbps|mbps|gbps) limit 1-131072 (packets | bytes | kbytes) percent 1-100

This object is used to set the units for the specified objects Enumeration: 'gbps': 4, 'bytes': 6, 'mbps': 3, 'percent': 9, 'packets': 5, 'kbytes': 7, 'bps': 1, 'kbps': 2, 'average': 8.

his object is used to set the Minimum random threashold

This object is used to set the Maximum random threashold

This object is used to set the units for Random Minimum Enumeration: 'packets': 3, 'percent': 4, 'bytes': 1, 'kbytes': 2.

This object is used to set the units for Random Maximum Enumeration: 'packets': 3, 'percent': 4, 'bytes': 1, 'kbytes': 2.

This object is used to set the service name, to attach a child policy onto a parent policy

Max accessList suported

The configuration commands, and user can configure functions via setting this entry as proper value. Enumeration: 'setMaxAccessList': 1, 'unsetMaxAccessList': 2.

status of user command. User have to check this value as .busy. or .idle. before do setRequest.

the wait-time until setRequest end. In case of short-time command, this value is 0

the time stamp of the last command. (don.t care)

Result of the last command.

Max accessList suported

Description.