RT-AC68U-MIB: View SNMP OID List / Download MIB

The MIB module of Asus RT-AC68U.

The network name or SSID is a unique name that identifies the wireless network. WiFi devices automatically detect all networks within range. Assign an identification string of up to 32 characters for your wireless connection.

If [YES] is selected, your SSID does not show in site surveys by wireless mobile clients and they can only connect to your ASUS Wireless Router with your SSID of AP. Enumeration: 'yes': 1, 'no': 0.

This item allows you to select any of these options for the Wireless Mode of your 802.11n interface. [Auto]: Allows 802.11n, 802.11g, and 802.11b devices to connect to RT-AC68U. [Legacy]: Allows 802.11b/g/n devices to connect to RT-AC68U, but 802.11n devices only run at a speed of 54Mbps. [n Only]: Maximizes performance, but does not allow 802.11g and 802.11b devices to connect to your device. Enumeration: 'auto': 0, 'legacy': 2, 'dot11N-only': 1.

Enumeration: 'yes': 1, 'no': 0.

Tick b/g Protection to allow b/g devices to connect to RT-AC68U without affecting 11n devices, but this increases the router's workload. Enumeration: 'enable': 1, 'disable': 2.

Selecting a wider channel bandwidth provides you with a higher transmission speed. Uses 40MHz coexistent bandwidth to maximize the wireless throughput. If you experience issues with wireless stability, please choose the default mode (20MHz). Enumeration: 'b20-or-40MHz': 0, 'b40MHz': 2, 'b20MHz': 1.

The radio channel for wireless connection operation. 0: auto

Select the extension channel used in the 20/40MHz channel bandwidth mode. 802.11n uses the extension channel to get extra speed. For channels 1 to 4, you can only select an upper channel. For channels 5 to 7, you can select a lower or an upper channel as the extension channel. For channels above 7, you can only select a lower channel. Enumeration: 'auto': 1, 'below': 2, 'above': 3.

This field enables the authentication methods for wireless clients. Enumeration: 'wpa-auto-enterprise': 8, 'wpa-personal': 3, 'wpa-enterprise': 6, 'shared-key': 2, 'open-system': 1, 'wpa-auto-personal': 5, 'wpa2-enterprise': 7, 'wpa2-personal': 4, 'radius-with-8021x': 9.

Enable WEP Encyption to encrypt data. Enumeration: 'wep-64bits': 1, 'none': 0, 'wep-128bits': 2.

Default transmit WEP Key. Enumeration: 'second': 2, 'forth': 4, 'third': 3, 'first': 1.

Wep Key Table.

Wep key index.

WEP key value.

If you select WEP Encryption, you can key in some words in this field to generate WEP keys automatically.

Enable WPA Encryption to encrypt data. Enumeration: 'tkip': 1, 'aes': 2, 'tkip-aes': 3, 'none': 0.

This field requires a password of 8 and 63 characters(letters, numbers or a combination) or 64 hex digits to start the encryption process .

This field specifies the interval (in seconds) after which a WPA group key is changed . Enter [0] (zero) to indicate that a periodic key-change is not required.

Selecting Yes allows Wi-Fi Protected Setup (WPS) to simplify the process of connecting any device to the wireless network. WPS support the authentication of Open system, WPA-Personal, WPA2-Personal. Not support Shared Key, WPA-Enterprise, WPA2-Enterprise and Radius. Enumeration: 'enable': 1, 'disable': 2.

If [YES] is selected, frequency of WPS will be switched to 5G. This value can be set only when WPS is disabled. Enumeration: 'nothing': 2, 'yes': 1.

Key in the router's PIN code in the client's WPS utility and configure the network name and security settings.

Selecting PIN (Personal Information Number) you have to enter a number to establish a wireless connection. Select PBC (Push Button Configuration) you have to push a button to establish a wireless connection. Enumeration: 'nothing': 3, 'clientPinCode': 2, 'pbc': 1.

MAC address of 2.4GHz.

Select [AP Only] to disable Wireless Bridge function. Select [WDS Only] to disable local wireless station connection. Select [Hybrid] to enable Wireless bridge function and wireless stations will be able to connect to the AP. Enumeration: 'wds-only': 2, 'hybrid': 3, 'ap-only': 1.

Select [Yes] to connect RT-AC68U to other APs listed in the Remote AP List. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'nothing': 2, 'scan': 1.

AP scan result entry index.

BSSID of the AP scan result.

SSID of the AP scan result.

Remote AP list.

Remote AP Index.

MAC address of remote bridge APs.

Delete the AP enntry. Enumeration: 'yes': 1, 'no': 2.

In Accept mode, RT-AC68U only accept clients with MAC address in the list. In Reject mode, RT-AC68U will reject clients with MAC address in the list. Enumeration: 'disable': 1, 'accept': 2, 'reject': 3.

Mac filter list.

Mac filter list index

MAC address of station which device controls its access.

Delete the mac filter entry. Enumeration: 'yes': 1, 'no': 2.

The IP address of the RADIUS server for wireless authentication and dynamic WEP key derivation.

The UDP port number for connection to the RADIUS server.

The password to connect to the RADIUS server.

Select [Yes] to enable radio function. Enumeration: 'yes': 1, 'no': 0.

Select [Yes] to enable wirelss schedule function. Enumeration: 'yes': 1, 'no': 0.

This field defines the dates that wireless function is enabled. Bits: 'tuesday': 1, 'thursday': 3, 'friday': 4, 'wednesday': 2, 'monday': 0.

Hour of starting time of weekdays to enable 2.4G radio.

Minute of starting time of weekdays to enable 2.4G radio.

Hour of ending time of weekdays to enable 2.4G radio.

Minute of ending time of weekdays to enable 2.4G radio.

This field defines the dates that wireless function is enabled. Bits: 'sunday': 1, 'saturday': 0.

Hour of starting time of weekend to enable 2.4G radio.

Minute of starting time of weekend to enable 2.4G radio.

Hour of ending time of weekend to enable 2.4G radio.

Minute of ending time of weekend to enable 2.4G radio.

When this feature is enabled, wireless clients or devices will not be able to communicate with each other. You may want to utilize this feature if you have many guests that frequent your wireless network. Enumeration: 'yes': 1, 'no': 0.

In multiple AP or wireless router-repeater environment, client sometimes cannot automatically connect to the AP with better signal because it still connect to main wireless router. Enabling this feature would force disconnecting the client and main router when the signal strength is under the threshold and client can choose the AP with better signal. Enumeration: 'enable': 1, 'disable': 0.

Disconnect clients with RSSI lower than the settings.

When enabled, IGMP Snooping monitors IGMP communication among devices and optimizes wireless multicast traffic. Enumeration: 'enable': 1, 'disable': 0.

Select the multicast transmission rate. You are recommended to select Auto to maximize performance. Enumeration: 'rCCK-5': 12, 'rCCK-2': 11, 'rOFDM-18': 5, 'rCCK-1': 10, 'auto': 1, 'rOFDM-12': 4, 'rOFDM-36': 7, 'rOFDM-24': 6, 'rOFDM-6': 2, 'rOFDM-48': 8, 'rOFDM-9': 3, 'rOFDM-54': 9, 'rCCK-11': 13.

The Preamble type defines the length of the CRC (Cyclic Redundancy Check) block, which is a technique for detecting data transmission errors among wireless devices. We recommend that you configure all wireless devices to the same preamble type. Use short preamble for wireless devices in high network traffic areas. Use long preamble for older wireless devices. Enumeration: 'auto': 3, 'short': 2, 'long': 1.

Select 'Enable' to use RTS for every AMPDU. Enumeration: 'enable': 1, 'disable': 0.

Lower the signal RTS (Request To Send) to promote the transmission efficiency in condition of noisy environment or too many clients.

DTIM (Delivery Traffic Indication Message) is included in Beacon packet.The DTIM Interval (1-255) means the period of time to wake up wireless clients from Sleep Mode. The default value is 3.

Beacon Interval means the period of time between one beacon and the next one. The default value is 100 (the unit is millisecond, or 1/1000 second). Lower the Beacon Interval to improve transmission performance in unstable environment or for roaming clients, but it will be power consuming.

Selecting [Enable] enables TX Bursting to improve the transmission speed (from AP to client) of g devices. Enumeration: 'enable': 1, 'disable': 2.

Enable or Disable WMM APSD (Automatic Power Save Delivery). Enumeration: 'enable': 1, 'disable': 2.

Optimize max number of mpdus in an AMDPU. Enumeration: 'enable': 1, 'disable': 0.

Optimize max number of ack to suppress in a row. Enumeration: 'enable': 1, 'disable': 0.

Increase Tx Power to enhance the transmission quality or decrease Tx Power to reduce power consumption.

The network name or SSID is a unique name that identifies the wireless network. WiFi devices automatically detect all networks within range. Assign an identification string of up to 32 characters for your wireless connection.

If [YES] is selected, your SSID does not show in site surveys by wireless mobile clients and they can only connect to your ASUS Wireless Router with your SSID of AP. Enumeration: 'yes': 1, 'no': 0.

This item allows you to select any of these options for the Wireless Mode of your 802.11n interface. [Auto]: Allows 802.11n, 802.11g, and 802.11b devices to connect to RT-AC68U. [Legacy]: Allows 802.11b/g/n devices to connect to RT-AC68U, but 802.11n devices only run at a speed of 54Mbps. [n Only]: Maximizes performance, but does not allow 802.11g and 802.11b devices to connect to your device. Enumeration: 'auto': 0, 'legacy': 2, 'dot11N-only': 1, 'n-ac-mixed': 8.

Enumeration: 'yes': 1, 'no': 0.

Selecting a wider channel bandwidth provides you with a higher transmission speed. Uses 40MHz coexistent bandwidth to maximize the wireless throughput. If you experience issues with wireless stability, please choose the default mode (20MHz). Enumeration: 'b20MHz': 1, 'b40MHz': 2, 'b20-40-80MHz': 0, 'b80MHz': 3.

The radio channel for wireless connection operation. 0: auto

Enumeration: 'auto': 1.

This field enables the authentication methods for wireless clients. Enumeration: 'wpa-auto-enterprise': 8, 'wpa-personal': 3, 'sharedkey': 2, 'wpa2-personal': 4, 'opensystem': 1, 'wpa-enterprise': 6, 'wpa-auto-personal': 5, 'wpa2-enterprise': 7, 'radius-with-8021x': 9.

Enable WEP Encyption to encrypt data. Enumeration: 'wep-64bits': 1, 'none': 0, 'wep-128bits': 2.

Default transmit WEP Key. Enumeration: 'second': 2, 'forth': 4, 'third': 3, 'first': 1.

Wep Key Table.

Wep key index

WEP key value

If you select WEP Encryption, you can key in some words in this field to generate WEP keys automatically.

Enable WPA Encryption to encrypt data. Enumeration: 'tkip': 1, 'aes': 2, 'tkip-aes': 3, 'none': 0.

This field requires a password of 8 and 63 characters(letters, numbers or a combination) or 64 hex digits to start the encryption process .

This field specifies the interval (in seconds) after which a WPA group key is changed . Enter [0] (zero) to indicate that a periodic key-change is not required.

Selecting Yes allows Wi-Fi Protected Setup (WPS) to simplify the process of connecting any device to the wireless network. WPS support the authentication of Open system, WPA-Personal, WPA2-Personal. Not support Shared Key, WPA-Enterprise, WPA2-Enterprise and Radius. Enumeration: 'enable': 1, 'disable': 2.

If [YES] is selected, frequency of WPS will be switched to 2.4G. This value can be set only when WPS is disabled. Enumeration: 'nothing': 2, 'yes': 1.

Key in the router's PIN code in the client's WPS utility and configure the network name and security settings.

Selecting PIN (Personal Information Number) you have to enter a number to establish a wireless connection. Select PBC (Push Button Configuration) you have to push a button to establish a wireless connection. Enumeration: 'nothing': 3, 'clientPinCode': 2, 'pbc': 1.

MAC address of 5GHz.

Select [AP Only] to disable Wireless Bridge function. Select [WDS Only] to disable local wireless station connection. Select [Hybrid] to enable Wireless bridge function and wireless stations will be able to connect to the AP. Enumeration: 'wds-only': 2, 'hybrid': 3, 'ap-only': 1.

Select [Yes] to connect RT-AC68U to other APs listed in the Remote AP List. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'nothing': 2, 'scan': 1.

AP scan result entry index.

BSSID of the AP scan result.

SSID of the AP scan result.

Remote AP list.

Remote AP Index.

MAC address of remote bridge APs.

Delete the AP enntry. Enumeration: 'yes': 1, 'no': 2.

In Accept mode, RT-AC68U only accept clients with MAC address in the list. In Reject mode, RT-AC68U will reject clients with MAC address in the list. Enumeration: 'disable': 1, 'accept': 2, 'reject': 3.

Mac filter list.

Mac filter list index

MAC address of station which device controls its access.

Delete the mac filter entry. Enumeration: 'yes': 1, 'no': 2.

The IP address of the RADIUS server for wireless authentication and dynamic WEP key derivation.

The UDP port number for connection to the RADIUS server.

The password to connect to the RADIUS server.

Select [Yes] to enable radio function. Enumeration: 'yes': 1, 'no': 0.

Select [Yes] to enable wirelss schedule function. Enumeration: 'yes': 1, 'no': 0.

This field defines the dates that wireless function is enabled. Bits: 'tuesday': 1, 'thursday': 3, 'friday': 4, 'wednesday': 2, 'monday': 0.

Hour of starting time of weekdays to enable 5G radio.

Minute of starting time of weekdays to enable 5G radio.

Hour of ending time of weekdays to enable 5G radio.

Minute of ending time of weekdays to enable 5G radio.

This field defines the dates that wireless function is enabled. Bits: 'sunday': 1, 'saturday': 0.

Hour of starting time of weekend to enable 2.4G radio.

Minute of starting time of weekend to enable 2.4G radio.

Hour of ending time of weekend to enable 2.4G radio.

Minute of ending time of weekend to enable 2.4G radio.

When this feature is enabled, wireless clients or devices will not be able to communicate with each other. You may want to utilize this feature if you have many guests that frequent your wireless network. Enumeration: 'yes': 1, 'no': 0.

In multiple AP or wireless router-repeater environment, client sometimes cannot automatically connect to the AP with better signal because it still connect to main wireless router. Enabling this feature would force disconnecting the client and main router when the signal strength is under the threshold and client can choose the AP with better signal. Enumeration: 'enable': 1, 'disable': 0.

Disconnect clients with RSSI lower than the settings.

When enabled, IGMP Snooping monitors IGMP communication among devices and optimizes wireless multicast traffic. Enumeration: 'enable': 1, 'disable': 0.

Select the multicast transmission rate. You are recommended to select Auto to maximize performance. Enumeration: 'rOFDM-18': 5, 'auto': 1, 'rOFDM-12': 4, 'rOFDM-36': 7, 'rOFDM-24': 6, 'rOFDM-6': 2, 'rOFDM-48': 8, 'rOFDM-9': 3, 'rOFDM-54': 9.

The Preamble type defines the length of the CRC (Cyclic Redundancy Check) block, which is a technique for detecting data transmission errors among wireless devices. We recommend that you configure all wireless devices to the same preamble type. Use short preamble for wireless devices in high network traffic areas. Use long preamble for older wireless devices. Enumeration: 'auto': 3, 'short': 2, 'long': 1.

Fragmentation Threshold sets the frame size of incoming messages (ranging from 256 to 2346 bytes) used as fragmentation boundary. If the frame size is too big, the heavy interference affects transmission reliability. If the frame size is too small, it decreases transmission efficiency.

Lower the signal RTS (Request To Send) to promote the transmission efficiency in condition of noisy environment or too many clients.

DTIM (Delivery Traffic Indication Message) is included in Beacon packet.The DTIM Interval (1-255) means the period of time to wake up wireless clients from Sleep Mode. The default value is 3.

Beacon Interval means the period of time between one beacon and the next one. The default value is 100 (the unit is millisecond, or 1/1000 second). Lower the Beacon Interval to improve transmission performance in unstable environment or for roaming clients, but it will be power consuming.

Selecting [Enable] enables TX Bursting to improve the transmission speed (from AP to client) of g devices. Enumeration: 'enable': 1, 'disable': 2.

Enable WMM (Wi-Fi Multimedia) to improve user experience of multimedia applications on your wireless network. Enumeration: 'auto': 1, 'enable': 2, 'disable': 3.

[No-Acknowledgement] is the acknowledge policy at MAC level. When enabled, it results in more efficient throughput but higher error rates in a noisy Radio Frequency (RF) environment. Enumeration: 'enable': 1, 'disable': 2.

Enable or Disable WMM APSD (Automatic Power Save Delivery). Enumeration: 'enable': 1, 'disable': 2.

Optimize max number of mpdus in an AMDPU. Enumeration: 'enable': 1, 'disable': 0.

Optimize max number of ack to suppress in a row. Enumeration: 'enable': 1, 'disable': 0.

The client's WLAN adapter and router both support beamforming technology. This technology allows these devices to communicate the channel estimation and steering direction to each other to improve download and uplink speed. Enumeration: 'enable': 1, 'disable': 0.

Increase Tx Power to enhance the transmission quality or decrease Tx Power to reduce power consumption.

Enumeration: 'yes': 1, 'no': 2.

The value of this object is IP Address of the device as seen in your local network. The default value is 192.168.1.1.

The value this object is Subnet Mask of the device as seen in your local network. The default value is 255.255.255.0.

Enumeration: 'yes': 1, 'no': 2.

Enable the DHCP server function to allow the router's DHCP server to automatically assign IP addresses to network clients. If this function is disabled, you need to manually assign the IP address settings on your LAN devices. Enumeration: 'yes': 1, 'no': 2.

The Domain Name for clients who request IP Address from the DHCP Server.

The first address in the pool to be assigned by the DHCP server in LAN.

This field indicates the last address in the pool to be assigned by the DHCP server in LAN.

Set the lease time that the network client is allowed to use its current IP address to connect to the wireless router. When the lease time expires, the network client should either renew or get a new IP address from the wireless router's DHCP server.

This field indicates the IP address of gateway in your LAN. If you leave it blank, the IP address of RT-AC68U will be assigned.

This field indicates the IP address of DNS to provide to clients that request IP Address from DHCP Server. You can leave it blank, then the DNS request will be processed by RT-AC68U.

The Windows Internet Naming Service manages interaction of each PC with the Internet. If you use a WINS server, enter IP Address of server here.

Assign a fixed IP address for a specific client. The client's MAC address is required. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'nothing': 2, 'scan': 1.

Client entry index.

MAC address of the client list.

IP address of the client list.

Name of the client list.

Assigned IP around the DHCP list.

Remote AP Index.

MAC address of assigned IP around the DHCP list.

IP address of assigned IP around the DHCP list.

Delete the assigned IP enntry. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'nothing': 2, 'scan': 1.

Client entry index.

IP address of the client list.

Name of the client list.

Static route list.

Static Route Index.

IP address of static route list.

Netmask of static route list.

Netmask of static route list.

Metric of static route list.

Interface of static route list. Enumeration: 'wan': 3, 'lan': 1, 'man': 2.

Delete the static route enntry. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'none': 1, 'singtel-others': 5, 'manual': 9, 'maxis-fiber-special': 8, 'maxis-fiber': 7, 'singtel-mio': 4, 'm1-fiber': 6, 'unifi-home': 2, 'unifi-business': 3.

This variable can be set only when the value of 'selectISPProfile' is 'none'. Enumeration: 'none': 1, 'lan3-and-lan4': 7, 'lan3': 4, 'lan2': 3, 'lan1': 2, 'lan4': 5, 'lan1-and-lan2': 6.

User can set this variable only when 'selectISPProfile' is 'manual'. Blank value means internetVID won't be used. Value Range: 2-4094.

User can set this variable only when 'selectISPProfile' is 'manual'.

User can set this variable only when 'selectISPProfil'e is 'manual'. Blank value means internetVID won't be used. Value Range: 2-4094.

User can set this variable only when 'selectISPProfile' is 'manual'.

User can set this variable only when 'selectISPProfile' is 'manual'. Blank value means internetVID won't be used. Value Range: 2-4094.

User can set this variable only when 'selectISPProfile' is 'manual'.

Enumeration: 'rfc3442-and-microsoft': 4, 'rfc3442': 3, 'microsoft': 2, 'disable': 1.

Allows the wireless router to handle the multicast packets. Enabling multicast router also enables the RTP and RTSP functions. Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'enable': 1, 'disable': 2.

Use this function to run the IPTV application (such as VLC) on several computers at the same time. This function can convert multicast UDP streams to unicast HTTP streams. Enter the port (such as 4000) that you want to assign for the IPTV application, then use this format to enter the address in the play list to watch IPTV streams: http://[Router IP]: [Udpxy port]/[protocol]/[channel IP address]:[channel port] (such as http://192.168.1.1: 4000/udp/239.255.1.1:5000 or http://192.168.1.1:4000/rtp/239.255.1.2:5000). Enter 0 (zero) to disable this function.

Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'ctf-level2': 3, 'ctf-level1': 2, 'disable': 1.

Enumeration: 'pptp': 4, 'automatic-ip': 1, 'pppoe': 2, 'l2tp': 5, 'static-ip': 3.

Enumeration: 'yes': 1, 'no': 2.

NAT (Network Address Translation) is a process used in routers to replace the address information of network packet with new address information. Typical applications for NAT is router which connect to LAN with the WAN. In LAN every network devices had a private IP(LAN IP) but there is only one public IP(WAN IP). To grant the network devices access to the Internet, the router replaces the private IP address of the sender with its own public IP address in all outgoing data packets. The router saves all necessary information in a table(NAT table) so that incoming data packets can then be assigned on the correct network device. Enumeration: 'yes': 1, 'no': 2.

UPnP (Universal Plug and Play) allows several devices (routers, televisions, stereo systems, game consoles, cellular phone) to be controlled via an IP-based network with or without a central control through a gateway. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'yes': 1, 'no': 2.

If your WAN connection requires a static IP address, key in the IP address in this field.

If your WAN connection requires a static IP address, key in the subnet mask in this field.

If your WAN connection requires a static IP address, key in the gateway IP address in this field.

Allows this router to get the DNS IP address from the ISP automatically. Enumeration: 'yes': 1, 'no': 2.

This field indicates the IP address of DNS that RT-AC68U contact to.

This field indicates the IP address of DNS that RT-AC68U contact to.

Enumeration: 'none': 1, 'dot1x-md5': 2.

This field is only available when you set the WAN Connection Type as USB Modem, PPPoE, PPTP or L2TP.

This field is only available when you set WAN Connection Type as PPPoE.

This field is optional and allows you to configure to terminate your ISP connection after a specified period of time. A value of zero allows infinite idle time.

The Maximum Transmission Unit (MTU) of PPPoE packet. The default value is 1492. Change this value only if your ISP requires it.

The Maximum Receive Unit (MRU) of PPPoE packet. The default value is 1492. Change this value only if your ISP requires it.

This field is optional and may be specified by some ISPs. Check with your ISP and fill them in if required.

This field is optional and may be specified by some ISPs. Check with your ISP and fill them in if required.

This field is optional and may be specified by some ISPs. Check with your ISP and fill them in if required. Enumeration: 'mppe-40': 3, 'auto': 1, 'no-encryption': 2, 'mppe-128': 4.

This field is optional and may be specified by some ISPs. Check with your ISP and fill them in if required.

If your WAN connection type is PPTP or L2TP, Please enter the server name or server ip of the VPN server.

Enumeration: 'yes': 1, 'no': 2.

This field allows you to provide a host name for RT-AC68U. It is usually requested by your ISP.

MAC (Media Access Control) address is a unique identifier that identifies your computer or device in the network. ISPs monitor the MAC addresses of devices that connect to their services, and would disallow Internet connection for new MAC addresses. To fix this issue, you can do either of the following: *Contact your ISP and request to update the MAC address associated with your ISP subscription. *Clone or change the MAC address of the new device to match the MAC address of the original device.

Enumeration: 'normal-mode': 1, 'aggressive-mode': 2.

Enumeration: 'pptp': 4, 'automatic-ip': 1, 'pppoe': 2, 'l2tp': 5, 'static-ip': 3.

Enumeration: 'yes': 1, 'no': 2.

NAT (Network Address Translation) is a process used in routers to replace the address information of network packet with new address information. Typical applications for NAT is router which connect to LAN with the WAN. In LAN every network devices had a private IP(LAN IP) but there is only one public IP(WAN IP). To grant the network devices access to the Internet, the router replaces the private IP address of the sender with its own public IP address in all outgoing data packets. The router saves all necessary information in a table(NAT table) so that incoming data packets can then be assigned on the correct network device. Enumeration: 'yes': 1, 'no': 2.

UPnP (Universal Plug and Play) allows several devices (routers, televisions, stereo systems, game consoles, cellular phone) to be controlled via an IP-based network with or without a central control through a gateway. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'yes': 1, 'no': 2.

If your WAN connection requires a static IP address, key in the IP address in this field.

If your WAN connection requires a static IP address, key in the subnet mask in this field.

If your WAN connection requires a static IP address, key in the gateway IP address in this field.

Allows this router to get the DNS IP address from the ISP automatically. Enumeration: 'yes': 1, 'no': 2.

This field indicates the IP address of DNS that RT-AC68U contact to.

This field indicates the IP address of DNS that RT-AC68U contact to.

Enumeration: 'none': 1, 'dot1x-md5': 2.

This field is only available when you set the WAN Connection Type as USB Modem, PPPoE, PPTP or L2TP.

This field is only available when you set WAN Connection Type as PPPoE.

This field is optional and allows you to configure to terminate your ISP connection after a specified period of time. A value of zero allows infinite idle time.

The Maximum Transmission Unit (MTU) of PPPoE packet. The default value is 1492. Change this value only if your ISP requires it.

The Maximum Receive Unit (MRU) of PPPoE packet. The default value is 1492. Change this value only if your ISP requires it.

This field is optional and may be specified by some ISPs. Check with your ISP and fill them in if required.

This field is optional and may be specified by some ISPs. Check with your ISP and fill them in if required.

This field is optional and may be specified by some ISPs. Check with your ISP and fill them in if required. Enumeration: 'mppe-40': 3, 'auto': 1, 'no-encryption': 2, 'mppe-128': 4.

This field is optional and may be specified by some ISPs. Check with your ISP and fill them in if required.

If your WAN connection type is PPTP or L2TP, Please enter the server name or server ip of the VPN server.

Enumeration: 'yes': 1, 'no': 2.

This field allows you to provide a host name for RT-AC68U. It is usually requested by your ISP.

MAC (Media Access Control) address is a unique identifier that identifies your computer or device in the network. ISPs monitor the MAC addresses of devices that connect to their services, and would disallow Internet connection for new MAC addresses. To fix this issue, you can do either of the following: *Contact your ISP and request to update the MAC address associated with your ISP subscription. *Clone or change the MAC address of the new device to match the MAC address of the original device.

Enumeration: 'normal-mode': 1, 'aggressive-mode': 2.

Enumeration: 'yes': 1, 'no': 0.

Enumeration: 'td-scdma': 3, 'wcdma': 1, 'wimax': 4, 'cdma2000': 2.

Enumeration: 'auto': 1, 'only3g': 4, 'only4g': 3, 'both4g-3g': 2, 'only2g': 5.

This is optional. If you do not know the APN service name, please contact your ISP.

Please enter your dial number.

Please input the Personal Identification Number(PIN) code of your SIM card. It must be the number which length is greater than 4 and smaller than 8. If you do not know the PIN code, please contact your ISP.

Please enter your username.

Please enter your password.

Enumeration: 'asus-t500': 2, 'huawei-k3520': 12, 'mts-ac2746': 32, 'samsung-u200': 1, 'cs15': 42, 'cs17': 43, 'onda-mw833up': 31, 'huawei-e372': 17, 'huawei-e161': 8, 'huawei-e122': 18, 'huawei-e1823': 22, 'huawei-e169': 9, 'zte-mfk3570-z': 41, 'bandluxe-c339': 5, 'alcatel-oune-touch-x220s': 27, 'zte-mf622': 37, 'huawei-e1800': 14, 'bandluxe-c170': 4, 'auto': 0, 'huawei-et128': 13, 'huawei-e160e': 19, 'huawei-e1752c': 25, 'huawei-e160g': 7, 'anydata-adu-510a': 28, 'zte-mu351': 34, 'huawei-k4505': 15, 'anydata-adu-500a': 29, 'zte-mf626': 38, 'zte-mf632': 39, 'huawei-e220': 11, 'zte-ac5710': 33, 'zte-mf636': 36, 'onda-mt833up': 30, 'huawei-e176': 10, 'huawei-e1750c': 24, 'huawei-e172': 16, 'huawei-e173': 21, 'bandluxe-c120': 3, 'icon401': 44, 'alcatel-x200': 26, 'zte-mf112': 40, 'huawei-e1762': 23, 'zte-mf100': 35, 'huawei-e1550': 6, 'huawei-e1552': 20.

Primary WAN and secondary wan must be different. Enumeration: 'wan': 1, 'lan': 3, 'usb': 2.

Enumeration: 'lan4': 4, 'lan3': 3, 'lan2': 2, 'lan1': 1.

Value 'none' means there is no secondary WAN. And primary WAN and secondary wan must be different. Enumeration: 'wan': 1, 'lan': 3, 'none': 0, 'usb': 2.

Enumeration: 'lan4': 4, 'lan3': 3, 'lan2': 2, 'lan1': 1.

Load Balance optimizes resource use and maximizes throughput. Use Failover mode for better performance if the difference of bandwidth between the Primary and Secondary WAN is more than 10Mbps. Enumeration: 'fail-over': 1, 'load-balance': 2.

Enumeration: 'yes': 1, 'no': 2.

Time interval between two ping packets.

Time delay before the first ping packet is sent out when the router is restarted.

Maximum number of pings the router sends continuously. If this value is reached, the primary WAN connection will be switched to the secondary WAN.

Once switched to secondary wan, firmware can still detect the primary wan. When primary wan keep IP over the set value (Interval+delay)*failback count, the connection switched back to primary wan.

You can enable Ping Time Watchdog to continuously monitor the primary WAN connection between ZVMODELVZ and the remote host. The router will continuously ping a user defined target in this setting. If the router fails to ping the target IP address, the rouer will automatically do a failover. Enumeration: 'yes': 1, 'no': 2.

The IP address of the target host where the router is sending ping packets continuously.

Enumeration: 'yes': 1, 'no': 2.

Routing Rules.

Routing Rule index.

Source IP address of the routing rule.

Destination IP address of the routing rule.

Enumeration: 'primary-wan': 1, 'secondary-wan': 2.

Delete the routing rule enntry. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'yes': 1, 'no': 2.

Prt tirgger list.

Port trigger index.

Description of port trigger list.

Port of port trigger list.

Protocol of port trigger list. Enumeration: 'udp': 2, 'tcp': 1.

Incoming port of port trigger list.

Incoming protocol of port trigger list. Enumeration: 'udp': 2, 'tcp': 1.

Delete the port trigger enntry. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'nothing': 2, 'scan': 1.

Client entry index.

MAC address of the client list.

Name of the client list.

Port forwarding list.

Port Forwarding Index.

Service name of port forwarding list.

Port range of port forwarding list.

Local IP of port forwarding list.

Local port of port forwarding list.

Protocol of port forwarding list. Enumeration: 'both': 3, 'udp': 2, 'other': 4, 'tcp': 1.

Delete the port forwarding entry. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'yes': 1, 'no': 2.

If IP Address of Exposed Station is not set(blank), DMZ is disabled.

Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'dyndns-static': 4, 'dyndns-custom': 3, 'dnsomatic': 7, 'asus': 1, 'dyndns': 2, 'zoneedit': 6, 'no-ip': 9, 'tunnelbroker': 8, 'tzo': 5.

The host name cannot accept number prefix and '.' (such as '123abc' or 'aaa.bbb').

Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'enable': 1, 'disable': 2.

Enable PPPoE relay allows devices in LAN to establish a individual PPPoE connections that passes through NAT. Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'static-ipv6': 6, 'disable': 1, 'tunnel-6in4': 4, 'tunnel-6to4': 3, 'tunnel-6rd': 5, 'native': 2.

Enumeration: 'enable': 1, 'disable': 0.

Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'stateful': 2, 'stateless': 1.

Value Range: 0001-ffff

Value Range: 0001-ffff

Allows this router to get the DNS IP address from the ISP automatically. Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'enable': 1, 'disable': 2.

Enumeration: 'on': 1, 'off': 0.

Enumeration: 'pptp': 1, 'openVPN': 2.

Enumeration: 'yes': 1, 'no': 2.

Tftp server ip.

Export OpenVPN configuration file. Enumeration: 'nothing': 2, 'export': 1.

VPN user list.

VPN user index.

User name of vpn user list.

Password of vpn user list.

Connectin status of the user. Enumeration: 'connected': 1, 'disconnected': 2.

VPN Ip.

Remote ip of vpn client.

Delete the vpn user enntry. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'vpn-client-to-lan': 3, 'disable': 1, 'lan-to-vpn-client': 2, 'both': 4.

Enumeration: 'auto': 1, 'ms-chapv1': 2, 'ms-chapv2': 3.

Bits: 'mppe-40': 1, 'no-encryption': 2, 'mppe-128': 0.

Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'yes': 1, 'no': 2.

Maximum 10 clients

VPN server list.

VPN server index.

Description of vpn server.

There can be only one OpenVPN profile. Enumeration: 'pptp': 1, 'none': 0, 'l2tp': 2, 'openVPN': 3.

User name of VPN server.

Password of VPN server.

Connectin status of VPN server. Enumeration: 'connected': 1, 'disconnected': 2.

Delete the VPN server entry. Enumeration: 'yes': 1, 'no': 2.

Connect to the VPN server. Enumeration: 'nothing': 3, 'disconnect': 2, 'connect': 1.

Tftp server ip.

Type of imported file. ovnp: .ovpn file ca: Certificate Authority cert: Client Certificate key: Client Key static: Static Key Enumeration: 'none': 0, 'ovpn': 1, 'ca': 2, 'cert': 3, 'static': 5, 'key': 4.

The file name of the .vpn file or CA file which will be imported to the device.

Import will upload the .vpn file or CA file to the device. Enumeration: 'nothing': 2, 'import': 1.

Certificate Authority

Client Certificate

Client Key

Static Key(Optional)

Disabling the firewall will deactivate all the related functions. Enumeration: 'yes': 1, 'no': 2.

A 'denial-of-service' attack is an explicit attempt to deny legitimate users from using a service or computer resource. Enabling this feature can protect the router from DoS attack but it would increase the router's workload. Enumeration: 'yes': 1, 'no': 2.

This field indicates the kind of packets logged between LAN and WAN. Enumeration: 'both': 4, 'none': 1, 'accepted': 3, 'dropped': 2.

This feature allows you to respond to ping request from WAN. Enumeration: 'yes': 1, 'no': 2.

This field defines the dates that URL filter will be enabled. Enumeration: 'enable': 1, 'disable': 0.

URL filter list.

URL Filter Index.

URL of url filter list.

Delete the url filter enntry. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'enable': 1, 'disable': 0.

Keyword filter list.

Keyword Filter Index.

Keyword of keyword filter list.

Delete the keyword filter enntry. Enumeration: 'yes': 1, 'no': 2.

Select [Yes] to enable filter that specify IP or port for control incoming and outgoing packets. Enumeration: 'yes': 1, 'no': 2.

Select either White List or Black List to accept or reject those LAN to WAN packet exchanges for clients specified in the filter table. Enumeration: 'black-list': 2, 'white-list': 1.

This field defines the dates that LAN to WAN filter will be enabled. Bits: 'tuesday': 1, 'thursday': 3, 'friday': 4, 'wednesday': 2, 'monday': 0.

Hour of starting time of weekdays to enable Network Services Filter.

Minute of starting time of weekdays to enable Network Services Filter.

Hour of ending time of weekdays to enable Network Services Filter.

Minute of ending time of weekdays to enable Network Services Filter.

This field defines the dates that LAN to WAN filter will be enabled. Bits: 'sunday': 1, 'saturday': 0.

Hour of starting time of weekend to enable Network Services Filter.

Minute of starting time of weekend to enable Network Services Filter.

Hour of ending time of weekend to enable Network Services Filter.

Minute of ending time of weekend to enable Network Services Filter.

This field defines a list of LAN to WAN ICMP packets type that will be filtered. For example, if you would like to filter Echo(type 8) and Echo Reply(type 0) ICMP packets, you need to enter a string with numbers separated by blank, such as, [0 8].

Network services filter list.

Network Services Filter Index.

For source or destination IP address, you can : (a) enter a specific IP address, such as '192.168.122.1'; (b) enter IP addresses within one subnet or within the same IP pool, such as '192.168.123.*', or '192.168.*.*'; or (c) enter all IP addresses as '*.*.*.*'.

For source or destination port range, you can either : a) enter a specific port, such as '95'; or b) enter ports within a range, such as '103:315', '>100', or '<65535'.

For source or destination IP address, you can : (a) enter a specific IP address, such as '192.168.122.1'; (b) enter IP addresses within one subnet or within the same IP pool, such as '192.168.123.*', or '192.168.*.*'; or (c) enter all IP addresses as '*.*.*.*'.

For source or destination port range, you can either : a) enter a specific port, such as '95'; or b) enter ports within a range, such as '103:315', '>100', or '<65535'.

Protocol type. Enumeration: 'none': 0, 'tcp-psh': 8, 'tcp-rst': 6, 'tcp-fin': 5, 'udp': 9, 'tcp': 1, 'tcp-syn': 3, 'tcp-ack': 4, 'tcp-all': 2, 'tcp-urg': 7.

Delete the network services filter enntry. Enumeration: 'yes': 1, 'no': 2.

Select [Yes] to enable IPv6 firewall. Enumeration: 'yes': 1, 'no': 2.

Network services filter list.

Inbound firewall rules Index.

Key in the LAN client's IP address.

Port range accepts various formats such as Port Range (300:350), individual ports (566,789) or Mix (1015:1024,3021).

Protocol type. Enumeration: 'both': 3, 'udp': 2, 'other': 4, 'none': 0, 'tcp': 1.

Delete the inbound firewall rule. Enumeration: 'yes': 1, 'no': 2.

RT-AC68U supports several operation modes to meet different requirements. Please select the mode that match your situation. * In wireless router/ IP sharing mode, RT-AC68U connects to the Internet via PPPoE, DHCP, PPTP, L2TP, or Static IP and shares the wireless network to LAN clients or devices. In this mode, NAT, firewall, and DHCP server are enabled by default. UPnP and Dynamic DNS are supported for SOHO and home users. Select this mode if you are a first-time user or you are not currently using any wired/wireless routers. * In Repeater mode, RT-AC68U wirelessly connects to an existing wireless network to extend the wireless coverage. In this mode, the firewall, IP sharing, and NAT functions are disabled. * In Access Point (AP) mode, RT-AC68U connects to a wireless router through an Ethernet cable to extend the wireless signal coverage to other network clients. In this mode, the firewall, IP sharing, and NAT functions are disabled by default. * RT-AC68U can be configured in Media bridge mode.The Media Bridge mode provides the fastest 802.11ac Wi-Fi connection for multiple media devices simultaneously. To set up the Media Bridge mode, you need two RT-AC68U: one configured as the Media station and the other as a router.Configure one RT-AC68U as a router and another RT-AC68U as an 802.11ac Media bridge to provide a simultaneous 802.11ac Wi-Fi connection for your media devices such as computer, Smart TV, game console, DVR, or media player via Ethernet cable.Change to Media Bridge mode to provide a simultaneous 802.11ac Wi-Fi connection for your media devices. In media bridge mode, only wireless devices connect to the P-AP. Client devices need to be connected to the media bridge with a network cable. Enumeration: 'repeater-mode': 2, 'wireless-router-mode': 1, 'access-point-mode': 3, 'media-bridge': 4.

Password cannot be greater than 16 characters.

Enumeration: 'activate-wps': 2, 'toggle-radio': 1.

This field allows to assign a remote server to record log messages of RT-AC68U. If you leave it blank, the system will record up to 1024 messages on RT-AC68U.

1 (GMT-12:00) Eniwetok, Kwajalein 2 (GMT-11:00) Midway Island, Samoa 3 (GMT-10:00) Hawaii 4 (GMT-09:00) Alaska 5 (GMT-08:00) Pacific Time (US, Canada) 6 (GMT-07:00) Mountain Time (US, Canada) 7 (GMT-07:00) Arizona 8 (GMT-07:00) Chihuahua, La Paz, Mazatlan 9 (GMT-06:00) Central Time (US, Canada) 10 (GMT-06:00) Saskatchewan 11 (GMT-06:00) Guadalajara, Mexico City 12 (GMT-06:00) Monterrey 13 (GMT-06:00) Central America 14 (GMT-05:00) Eastern Time (US, Canada) 15 (GMT-05:00) Indiana (East) 16 (GMT-05:00) Bogota, Lima, Quito 17 (GMT-04:00) Atlantic Time (Canada) 18 (GMT-04:00) Caracas, La Paz 19 (GMT-04:00) Santiago 20 (GMT-03:30) Newfoundland 21 (GMT-03:00) Brasilia 22 (GMT-03:00) Buenos Aires, Georgetown 23 (GMT-03:00) Greenland 24 (GMT-02:00) Mid-Atlantic 25 (GMT-01:00) Azores 26 (GMT-01:00) Cape Verde Is. 27 (GMT) Greenwich Mean Time 28 (GMT) Dublin, Edinburgh, Lisbon, London 29 (GMT) Casablanca, Monrovia 30 (GMT+01:00) Belgrade, Bratislava, Budapest 31 (GMT+01:00) Ljubljana, Prague 32 (GMT+01:00) Sarajevo, Skopje, Sofija 33 (GMT+01:00) Vilnius, Warsaw, Zagreb 34 (GMT+01:00) Brussels, Copenhagen 35 (GMT+01:00) Madrid, Paris 36 (GMT+01:00) Amsterdam, Berlin, Bern 37 (GMT+01:00) Rome, Stockholm, Vienna 38 (GMT+01:00) West Central Africa 39 (GMT+02:00) Bucharest 40 (GMT+02:00) Cairo 41 (GMT+02:00) Helsinki, Riga, Tallinn 42 (GMT+02:00) Athens, Istanbul, Minsk 43 (GMT+02:00) Jerusalem 44 (GMT+02:00) Harare, Pretoria 45 (GMT+02:00) Ukraine 46 (GMT+03:00) Kaliningrad, Kuwait, Riyadh 47 (GMT+03:00) Nairobi 48 (GMT+03:00) Baghdad 49 (GMT+03:30) Tehran 50 (GMT+04:00) Moscow, St. Petersburg 51 (GMT+04:00) Volgograd 52 (GMT+04:00) Abu Dhabi, Muscat 53 (GMT+04:00) Baku, Tbilisi, Yerevan 54 (GMT+04:30) Kabul 55 (GMT+05:00) Islamabad, Karachi, Tashkent 56 (GMT+05:30) Calcutta, Chennai 57 (GMT+05:30) Mumbai, New Delhi 58 (GMT+05:30) Sri Jayawardenepura 59 (GMT+05:45) Kathmandu 60 (GMT+06:00) Almaty 61 (GMT+06:00) Yekaterinburg 62 (GMT+06:00) Astana, Dhaka 63 (GMT+06:30) Rangoon 64 (GMT+07:00) Bangkok, Hanoi, Jakarta, Novosibirsk 65 (GMT+08:00) Krasnoyarsk 66 (GMT+08:00) Beijing, Hong Kong 67 (GMT+08:00) Chongqing, Urumqi 68 (GMT+08:00) Kuala Lumpur, Singapore 69 (GMT+08:00) Taipei 70 (GMT+08:00) Perth 71 (GMT+08:00) Ulaan Bataar 72 (GMT+09:00) Irkutsk, Seoul 73 (GMT+09:00) Osaka, Sapporo, Tokyo 74 (GMT+09:30) Darwin 75 (GMT+09:30) Adelaide 76 (GMT+10:00) Yakutsk 77 (GMT+10:00) Canberra, Melbourne, Sydney 78 (GMT+10:00) Brisbane 79 (GMT+10:00) Hobart 80 (GMT+10:00) Guam, Port Moresby 81 (GMT+11:00) Vladivostok 82 (GMT+11:00) Solomon Is. 83 (GMT+11:00) New Caledonia 84 (GMT+12:00) Magadan, Fiji, Kamchatka, Marshall Is. 85 (GMT+12:00) Auckland, Wellington 86 (GMT+13:00) Nuku'alofa

Manually set the daylight saving time. Enumeration: 'yes': 1, 'no': 2.

The month of DST start time. Enumeration: 'mMay': 5, 'mMarch': 3, 'mJune': 6, 'mJanuary': 1, 'mNovember': 11, 'mJuly': 7, 'mOctober': 10, 'mApril': 4, 'mSeptember': 9, 'mAugust': 8, 'mFebruary': 2, 'mDecember': 12.

The week of DST start time.

The weekday of DST start time.

The hour of DST start time.

The month of DST end time. Enumeration: 'mMay': 5, 'mMarch': 3, 'mJune': 6, 'mJanuary': 1, 'mNovember': 11, 'mJuly': 7, 'mOctober': 10, 'mApril': 4, 'mSeptember': 9, 'mAugust': 8, 'mFebruary': 2, 'mDecember': 12.

The week of DST end time.

The weekday of DST end time.

The hour of DST end time.

To synchronize your system time with NTP Server.

Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'both': 3, 'http': 1, 'https': 2.

This feature allows you to configure the wireless router via the Internet. The default port is 8080 and you can use http://[WAN IP]:8080 or http://[DDNS name]:8080 to launch the wireless router's web user interface. Enumeration: 'yes': 1, 'no': 2.

To specify the port used to config RT-AC68U from the Internet( 1024:65535 ).

To specify the port used to config RT-AC68U from the Internet( 1024:65535 ).

Time to logout automatically. 0 means to disable the function of auto logout.

Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'nothing': 2, 'scan': 1.

Client entry index.

MAC address of the client list.

Name of the client list.

Specified IP address list.

Client Index.

IP address of client list.

Delete the specified IP client entry. Enumeration: 'yes': 1, 'no': 2.

Tftp server ip.

The file name of the firmware which will be uploaded to the device.

Upgrade firmware or not. When the firmware upgrading, please don't power off the device, and wait for 80 seconds to reconnect to device. Enumeration: 'nothing': 2, 'upgrade': 1.

Tftp server ip.

The file name of the config file which will be uploaded to the device or downloaded to the local PC.

The actions of tftp. 'Get' will get config file from remote PC to device, and 'Put' will upload config file from device to remote PC. Enumeration: 'put': 2, 'nothing': 3, 'get': 1.

Enable SNMP. Enumeration: 'yes': 1, 'no': 2.

The value of this object is the system name of the device. This value will be seen in the remote SNMP agent discovery result, and can be gotten and set by MIB browser and WEB.

The value of this object is the system location of the device. This value will be seen in the remote SNMP agent discovery result, and can be gotten and set by MIB browser and WEB.

The value of this object is the system contact information of the device. This value will be seen in the remote SNMP agent discovery result, and can be gotten and set by MIB browser and WEB.

The value of this object is the read-write community used in the SNMPv1 and SNMPv2c. The community string can be gotten and set by MIB browser and WEB.

The value of this object is the read-only community used in the SNMPv1 and SNMPv2c. The community string can be gotten and set by MIB browser and WEB.

The value of this object shows SNMPv3 authentication protocol. Enumeration: 'sha': 3, 'none': 1, 'md5': 2.

The authentication password. SNMPv3 pass phrases must be at least 8 characters long.

The value of this object shows SNMPv3 privacy protocol. Enumeration: 'none': 1, 'des': 2, 'aes': 3.

The privacy password. SNMPv3 passphrases must be at least 8 characters long.

The value of this object is the MIB version device supports.

1 commit 2 reboot 3 factoryDefault 4 restart_wireless 5 restart_net_and_phy 6 restart_net 7 restart_wan_if 8 restart_firewall 9 restart_ddns 10 restart_pppoe_relay 11 restart_allnet 12 restart_pptpd 13 restart_all 14 restart_time 15 restart_qos 16 restart_upnp 17 restart_ntpc 18 restart_snmpd 19 wps_apply 20 reset_wps 21 nothing Enumeration: 'restart-snmpd': 18, 'restart-wireless': 4, 'restart-net-and-phy': 5, 'restart-qos': 15, 'restart-ddns': 9, 'restart-net': 6, 'reboot': 2, 'factoryDefault': 3, 'restart-all': 13, 'restart-firewall': 8, 'reset-wps': 20, 'wps-apply': 19, 'restart-pppoe-relay': 10, 'restart-wan-if': 7, 'restart-pptpd': 12, 'nothing': 21, 'commit': 1, 'restart-allnet': 11, 'restart-upnp': 16, 'restart-time': 14, 'restart-ntpc': 17.

The value of this oject is the elapsed time (in hundredths of a second) since system boot.

Tftp server ip.

The file name of the syslog file which will be saved to the local PC. Default name is syslog.txt.

Select 'Save' to save syslog file to the local PC. Enumeration: 'nothing': 2, 'save': 1.

The value of this object shows the bss info of the device.

Get/Refresh station table of wireless 2g. Enumeration: 'nothing': 2, 'refresh': 1.

2.4G station list.

2.4G Station List Index

The MAC address of 2.4G station.

Show the associated state of 2.4G station.

Show the authorized state of 2.4G station.

Show the RSSI(dBm) of 2.4G station.

Show the PSM of 2.4G station.

The Tx Rate of 2.4G station.

The Rx Rate of 2.4G station.

The value of this oject is the elapsed time (in hundredths of a second) since the 2.4G station connects to RT-AC68U.

The value of this object shows the bss info of the device.

Get/Refresh station table of wireless 5g. Enumeration: 'nothing': 2, 'refresh': 1.

5G station list.

5G Station List Index

The MAC address of 5G station list.

Show the associated state of 2.4G station.

Show the authorized state of 2.4G station.

Show the RSSI(dBm) of 2.4G station.

Show the PSM of 2.4G station.

The Tx Rate of 2.4G station.

The Rx Rate of 2.4G station.

The value of this oject is the elapsed time (in hundredths of a second) since the 2.4G station connects to RT-AC68U.

DHCP leases list.

DHCP Leases List Index.

The host name of DHCP leases list.

The IP address of DHCP leases list.

The MAC address of DHCP leases list.

The expires of DHCP leases list.

IPv6 Connection Type.

WAN IPv6 Address.

WAN IPv6 Gateway.

LAN IPv6 Address.

LAN IPv6 Link-Local Address.

DHCP-PD.

LAN IPv6 Prefix.

DNS Address.

IPv6 LAN devices list.

IPv6 LAN Devices Index.

The host name of IPv6 LAN device.

The MAC address of IPv6 LAN device.

The IPv6 address of IPv6 LAN device.

Routing list.

Routing rule Index.

The destination of routing rule.

The gateway of routing rule.

The genmask of routing rule.

The flags of routing rule.

The metric of routing rule.

The ref of routing rule.

The use of routing rule.

The Iface of routing rule.

IPv6 Routing table.

IPv6 Routing rule Index.

The destination of IPv6 routing rule.

The gateway of IPv6 routing rule.

The flags of IPv6 routing rule.

The metric of IPv6 routing rule.

The ref of IPv6 routing rule.

The use of IPv6 routing rule.

The Iface of IPv6 routing rule.

This table shows the port forwarding status. Some P2P programs use the UPnP protocol to open the port and the port number is shown on this table.

Port Forwarding List Index.

The destination of port forwarding list.

The protocol of port forwarding list.

The port range of port forwarding list.

The redirect of port forwarding list.

The local port of port forwarding list.

This is the history log of active connections.

Index of active connection.

Protocol of active connection.

Nated address of active connection.

Destination address of active connection.

State of active connection.

Guest network list for 2G.

Guest Network List Index for 2G.

The enable of guest network list for 2G. Enumeration: 'enable': 1, 'disable': 2.

The SSID of guest network list for 2G.

The authentication method of guest network list of 2G. Open system with wep key, shared key, and radius with 802.1x are only supported when wireless mode is legacy. Enumeration: 'wpa-auto-enterprise': 8, 'wpa-personal': 3, 'sharedkey': 2, 'wpa2-personal': 4, 'opensystem': 1, 'wpa-enterprise': 6, 'wpa-auto-personal': 5, 'wpa2-enterprise': 7, 'radius-with-8021x': 9.

The wep encryption of guest network list for 2G. Enumeration: 'wep-64bits': 2, 'none': 1, 'wep-128bits': 3.

The key index of guest network list for 2G. Enumeration: 'second': 2, 'forth': 4, 'third': 3, 'first': 1.

The passphrase of guest network list for 2G.

The WPA encryption of guest network list for 2G. Enumeration: 'tkip': 1, 'aes': 2, 'tkip-aes': 3, 'none': 0.

The WPA pre-shared key of guest network list for 2G.

The access time of guest network list for 2G. Enumeration: 'limitless': 2, 'specific-time': 1.

The access time (hour) of guest network list for 2G.

The access time (minute) of guest network list for 2G.

The access intranet of guest network list for 2G. Enumeration: 'enable': 1, 'disable': 2.

Enable MAC filter of guest network of 2G. Note: MAC filter function of primary SSID must be enabled first. Enumeration: 'yes': 1, 'no': 2.

Wep key table of guest network 1 for 2G.

Wep key index of guest network 1 for 2G.

WEP key value of guest network 1 for 2G.

Wep key table of guest network 2 for 2G.

Wep key index of guest network 2 for 2G.

WEP key value of guest network 2 for 2G.

Wep key table of guest network 3 for 2G.

Wep key index of guest network 3 for 2G.

WEP key value of guest network 3 for 2G.

Guest network list for 5G.

Guest Network List Index for 5G.

The enable of guest network list for 5G. Enumeration: 'enable': 1, 'disable': 2.

The SSID of guest network list for 5G.

The authentication method of guest network list of 5G. Open system with wep key, shared key, and radius with 802.1x are only supported when wireless mode is legacy. Enumeration: 'wpa-auto-enterprise': 8, 'wpa-personal': 3, 'sharedkey': 2, 'wpa2-personal': 4, 'opensystem': 1, 'wpa-enterprise': 6, 'wpa-auto-personal': 5, 'wpa2-enterprise': 7, 'radius-with-8021x': 9.

The wep encryption of guest network list for 5G. Enumeration: 'wep-64bits': 2, 'none': 1, 'wep-128bits': 3.

The key index of guest network list for 5G. Enumeration: 'second': 2, 'forth': 4, 'third': 3, 'first': 1.

The passphrase of guest network list for 5G.

The WPA encryption of guest network list for 5G. Enumeration: 'tkip': 1, 'aes': 2, 'tkip-aes': 3, 'none': 0.

The WPA pre-shared key of guest network list for 5G.

The access time of guest network list for 5G. Enumeration: 'limitless': 2, 'specific-time': 1.

The access time (hour) of guest network list for 5G.

The access time (minute) of guest network list for 5G.

The access intranet of guest network list for 5G. Enumeration: 'enable': 1, 'disable': 2.

Enable MAC filter of guest network of 5G. Note: MAC filter function of primary SSID must be enabled first. Enumeration: 'yes': 1, 'no': 2.

Wep key table of guest network 1 for 5G.

Wep key index of guest network 1 for 5G.

WEP key value of guest network 1 for 5G.

Wep key table of guest network 2 for 5G.

Wep key index of guest network 2 for 5G.

WEP key value of guest network 2 for 5G.

Wep key table of guest network 3 for 5G.

Wep key index of guest network 3 for 5G.

WEP key value of guest network 3 for 5G.

Enumeration: 'on': 1, 'off': 2.

If the measured uplink speed is incorrect, you can assign it manually here.

If the measured downlink speed is incorrect, you can assign it manually here.

User specify rule list.

User Specify Rule Index.

Service name of user specify rule list.

For source or destination IP address, you can : (a) enter a specific IP address, such as '192.168.122.1'; (b) enter IP addresses within one subnet or within the same IP pool, such as '192.168.123.*', or '192.168.*.*'; or (c) enter all IP addresses as '*.*.*.*\'.

Destination port of user specify rule list.

Protocol of user specify rule list. Enumeration: 'tcp-or-udp': 3, 'udp': 2, 'any': 4, 'tcp': 1.

Set the network traffic limit (in KB) for a specific service to generate specific priorities for the service assigned to a specific port. For example, if two network clients, PC 1 and PC 2, are both accessing the Internet (set at port 80), but PC 1 exceeded the network traffic limit due to some downloading tasks, PC 1 will be given a lower priority. The Transferred column refers to the upstream and downstream traffic (outgoing and incoming network traffic) for one session. If you do not want to set the traffic limit, you can leave it blank.

Set the network traffic limit (in KB) for a specific service to generate specific priorities for the service assigned to a specific port. For example, if two network clients, PC 1 and PC 2, are both accessing the Internet (set at port 80), but PC 1 exceeded the network traffic limit due to some downloading tasks, PC 1 will be given a lower priority. The Transferred column refers to the upstream and downstream traffic (outgoing and incoming network traffic) for one session. If you do not want to set the traffic limit, you can leave it blank.

Priority of user specify rule list. Enumeration: 'high': 2, 'lowest': 5, 'highest': 1, 'medium': 3, 'low': 4.

Delete the user specify rule enntry. Enumeration: 'yes': 1, 'no': 2.

Minimum reserved bandwidth of highest upload priority.

Maximum bandwidth limit of highest upload priority.

Minimum reserved bandwidth of high upload priority.

Maximum bandwidth limit of high upload priority.

Minimum reserved bandwidth of medium upload priority.

Maximum bandwidth limit of medium upload priority.

Minimum reserved bandwidth of low upload priority.

Maximum bandwidth limit of low upload priority.

Minimum reserved bandwidth of lowest upload priority.

Maximum bandwidth limit of lowest upload priority.

Maximum bandwidth limit of highest download priority.

Maximum bandwidth limit of high download priority.

Maximum bandwidth limit of medium download priority.

Maximum bandwidth limit of low download priority.

Maximum bandwidth limit of lowest download priority.

Bits: 'ack': 0, 'rst': 3, 'icmp': 4, 'fin': 2, 'syn': 1.

Enable parental control. Enumeration: 'on': 1, 'off': 2.

Enumeration: 'nothing': 2, 'scan': 1.

Client entry index.

MAC address of the client.

Name of the client.

MAC address of the client.

Parental control client list.

Parental control client list index.

Enable the entry. Enumeration: 'enable': 1, 'disable': 0.

Name of parental control client.

Mac address of parental control client.

Time on Sunday at which clients are allowed to access internet. String format: If client can access internet from 1 o'clock to 3 o'clock, from 14 o'clock to 15 o'clock, and form 19 o'clock to 23 o'clock, please set '00-03,14-15,19-23'. '00-24' means all day.

Time on Monday at which clients are allowed to access internet. String format: If client can access internet from 1 o'clock to 3 o'clock, from 14 o'clock to 15 o'clock, and form 19 o'clock to 23 o'clock, please set '00-03,14-15,19-23'. '00-24' means all day.

Time on Tuesday at which clients are allowed to access internet. String format: If client can access internet from 1 o'clock to 3 o'clock, from 14 o'clock to 15 o'clock, and form 19 o'clock to 23 o'clock, please set '00-03,14-15,19-23'. '00-24' means all day.

Time on Wednesday at which clients are allowed to access internet. String format: If client can access internet from 1 o'clock to 3 o'clock, from 14 o'clock to 15 o'clock, and form 19 o'clock to 23 o'clock, please set '00-03,14-15,19-23'. '00-24' means all day.

Time on Thursday at which clients are allowed to access internet. String format: If client can access internet from 1 o'clock to 3 o'clock, from 14 o'clock to 15 o'clock, and form 19 o'clock to 23 o'clock, please set '00-03,14-15,19-23'. '00-24' means all day.

Time on Friday at which clients are allowed to access internet. String format: If client can access internet from 1 o'clock to 3 o'clock, from 14 o'clock to 15 o'clock, and form 19 o'clock to 23 o'clock, please set '00-03,14-15,19-23'. '00-24' means all day.

Time on Saturday at which clients are allowed to access internet. String format: If client can access internet from 1 o'clock to 3 o'clock, from 14 o'clock to 15 o'clock, and form 19 o'clock to 23 o'clock, please set '00-03,14-15,19-23'. '00-24' means all day.

Delete the entry. Enumeration: 'yes': 1, 'no': 2.

Enumeration: 'pptp': 4, 'automatic-ip': 1, 'pppoe': 2, 'l2tp': 5, 'static-ip': 3.

This field allows you to provide a host name for RT-AC68U. It is usually requested by your ISP.

MAC (Media Access Control) address is a unique identifier that identifies your computer or device in the network. ISPs monitor the MAC addresses of devices that connect to their services, and would disallow Internet connection for new MAC addresses. To fix this issue, you can do either of the following: *Contact your ISP and request to update the MAC address associated with your ISP subscription. *Clone or change the MAC address of the new device to match the MAC address of the original device. (This is optional.)

Enumeration: 'yes': 1, 'no': 2.

If you subscribe to PPPoE, PPTP or L2TP connection type, your ISP would give you a card or document that contains the account name and password on it. The account name and password that your ISP provided are used to connect to the Internet.

If you subscribe to PPPoE, PPTP or L2TP connection type, your ISP would give you a card or document that contains the account name and password on it. The account name and password that your ISP provided are used to connect to the Internet.

If your WAN connection requires a static IP address, key in the IP address in this field.

If your WAN connection requires a static IP address, key in the subnet mask in this field.

If your WAN connection requires a static IP address, key in the gateway IP address in this field.

MAC (Media Access Control) address is a unique identifier that identifies your computer or device in the network. ISPs monitor the MAC addresses of devices that connect to their services, and would disallow Internet connection for new MAC addresses. To fix this issue, you can do either of the following: *Contact your ISP and request to update the MAC address associated with your ISP subscription. *Clone or change the MAC address of the new device to match the MAC address of the original device. (This is optional.)

If you subscribe to PPPoE, PPTP or L2TP connection type, your ISP would give you a card or document that contains the account name and password on it. The account name and password that your ISP provided are used to connect to the Internet.

If you subscribe to PPPoE, PPTP or L2TP connection type, your ISP would give you a card or document that contains the account name and password on it. The account name and password that your ISP provided are used to connect to the Internet.

If your WAN connection requires a static IP address, key in the IP address in this field.

If your WAN connection requires a static IP address, key in the subnet mask in this field.

If your WAN connection requires a static IP address, key in the gateway IP address in this field.

Enumeration: 'yes': 1, 'no': 2.

If your WAN connection type is PPTP or L2TP, Please enter the server name or server ip of the VPN server.

Enumeration: 'none': 1, 'singtel-others': 5, 'manual': 9, 'maxis-fiber-special': 8, 'maxis-fiber': 7, 'singtel-mio': 4, 'm1-fiber': 6, 'unifi-home': 2, 'unifi-business': 3.

Show the IPTV STB Port.