PT3080-MIB: View SNMP OID List / Download MIB

This is the MIB file of PT3080 DVB-T/H Modulator. Copyright (c) 2008-2015 Protelevision Technologies A/S. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included.

The instrument serial number.

The product type designation.

The instrument Software Revision currently running.

The instrument Bootloader Software Revision.

The instrument O/S Kernel Version.

The options installed on this instrument.

The instrument FW1 revision

The instrument FW1 BL revision

The instrument FW2 revision

The instrument FW2 BL revision

The instrument FW3 revision

The instrument FW4 revision

The instrument PCB revision

The instrument Calibration revision

The instrument Calibration date

Force a reboot of the device on the designated image now. Enumeration: 'sameimage': 1, 'image1': 4, 'keeprunning': 0, 'image0': 3, 'otherimage': 2.

Restore all parameters to factory default and reboot the device on the same image. Enumeration: 'keeprunning': 0, 'reboot': 1.

The method used to synchronize system RTC. Mode auto means use gps if available else ntp else manual. Enumeration: 'auto': 1, 'gps': 2, 'manual': 0, 'ntp': 3.

The Time Zone used for displaying Data and Time.

The current date/time in local timezone of the device. Format is YYYY MM DD HH MM SS.

The flash Image the device is currently booted from.

The image 0 version string.

The date and time image 0 was installed.

The image 1 version string.

The date and time image 0 was installed.

Control the Service LED on frontpanel. Enumeration: 'on': 1, 'off': 0.

The system type to start in on next reboot. Enumeration: 'repeater': 1, 'modulator': 0.

The actual method used to synchronize system RTC. Enumeration: 'auto': 1, 'gps': 2, 'manual': 0, 'ntp': 3.

The Modulation Standard to start in on next reboot. Enumeration: 'isdbt': 3, 'iboc': 4, 'dvbt': 0, 'atsc': 2, 'dvbt2': 1.

Controls which language is used on web and facia. Change requires reboot. Enumeration: 'da-dk': 1, 'c': 0, 'it-it': 5, 'de-de': 6, 'fr-fr': 7, 'pt-br': 4, 'es-es': 3, 'ru-r': 2.

Number of seconds this unit has been turned on since production.

Number of seconds this unit has been unmuted since production.

Number of times this unit has been booted since last factory default restore.

ID of the backplane the device is plugged into

Raw ID of the backplane the device is plugged into

PCB version of the backplane the device is plugged into

Cable options of the backplane the device is plugged into

Manufacture ID of the backplane the device is plugged into

Calibration date of the backplane the device is plugged into

Calibration SW version of the backplane the device is plugged into

Partlist version of the backplane the device is plugged into

This table contains the scheduled actions

An entry for the scheduled action

Unique ID for this scheduled action entry

The interval at which this scheduled action entry will be executed Enumeration: 'hourly': 3, 'monthly': 6, 'never': 0, 'immediate': 1, 'daily': 4, 'weekly': 5, 'once': 2.

The recurrence hour used when pt3080SystemScheduledActionRecurrence is once, hourly, dayly, weekly and monthly.

The recurrence minute used when pt3080SystemScheduledActionRecurrence is once, hourly, dayly, weekly and monthly.

The recurrence weekday used when pt3080SystemScheduledActionRecurrence is weekly. Enumeration: 'monday': 0, 'tuesday': 1, 'friday': 4, 'wednesday': 2, 'thursday': 3, 'sunday': 6, 'saturday': 5.

The recurrence day of the monthe used when pt3080SystemScheduledActionRecurrence is monthly.

The recurrence date used when pt3080SystemScheduledActionRecurrence is once. The format is dd/mm/yyyy.

An extra random delay added before the action for this entry is executed. A setting of x means that a random delay between 0 and x seconds are added.

The action for this entry is executed Enumeration: 'repeatermode': 1, 'none': 0, 'mute': 5, 'reboot': 4, 'swupgrade': 3, 'preset': 2.

The new repeater mode to change to when pt3080SystemScheduledActionAction of type repeatermode is executed Enumeration: 'auto': 0, 'digital-transposer': 2, 'analog-iso-repeater': 3, 'digital-iso-repeater': 1, 'analog-transposer': 4.

The preset to load when pt3080SystemScheduledActionAction of type preset is executed Enumeration: 'auto': 0, 'digital-transposer': 2, 'analog-iso-repeater': 3, 'digital-iso-repeater': 1, 'analog-transposer': 4.

The image to reboot to when pt3080SystemScheduledActionAction of type reboot is executed Enumeration: 'sameimage': 0, 'image1': 3, 'image0': 2, 'otherimage': 1.

The system type to reboot to when pt3080SystemScheduledActionAction of type reboot is executed Enumeration: 'repeater': 1, 'modulator': 0, 'same': 2.

The mute mode to change into when pt3080SystemScheduledActionAction of type mute is executed Enumeration: 'on': 1, 'off': 0.

The protocol to use into when pt3080SystemScheduledActionAction of type swupgrade(3) is executed Enumeration: 'ftp': 1, 'http': 0.

The username to use into when pt3080SystemScheduledActionAction of type swupgrade(3) is executed

The password to use into when pt3080SystemScheduledActionAction of type swupgrade(3) is executed

The server name to use into when pt3080SystemScheduledActionAction of type swupgrade(3) is executed

The image path name to use into when pt3080SystemScheduledActionAction of type swupgrade(3) is executed

Network mode multi-frequency-network or single-frequency-network Enumeration: 'network-mode-mfn': 0, 'network-mode-sfn': 1.

Hierarchy mode. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'network-hierarchy-none': 0, 'network-hierarchy-h2': 2, 'network-hierarchy-h1': 1, 'network-hierarchy-h4': 3.

IFFT 2k, 4k or 8k mode. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'ifft-mode-8k': 2, 'ifft-mode-4k': 1, 'ifft-mode-2k': 0.

High Priority Code Rate. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'code-rate-3-4': 2, 'code-rate-7-8': 4, 'code-rate-5-6': 3, 'code-rate-1-2': 0, 'code-rate-2-3': 1.

Low Priority Code Rate. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'code-rate-3-4': 2, 'code-rate-7-8': 4, 'code-rate-5-6': 3, 'code-rate-1-2': 0, 'code-rate-2-3': 1.

If QPSK is selected and Hierarchical is <> NONE, then Hierarchical will be forced to NONE. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'qpsk': 0, 'qam16': 1, 'qam64': 2.

Guard Interval. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'guard-1-32': 0, 'guard-1-8': 2, 'guard-1-16': 1, 'guard-1-4': 3.

Sets the Cell ID value. Cannot be set if pt3080ModeMipControl is on(1).

Enables Cell ID in the TPS information. Cannot be set if pt3080ModeMipControl is on(1). Cannot be set to off(0) if pt3080ModeEnableDVBH is on(1) Enumeration: 'on': 1, 'off': 0.

Enables Deep Interleaver. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'on': 1, 'off': 0.

Enables DVB-H mode Enumeration: 'on': 1, 'off': 0.

Enables MPE Fec Low Priority. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'on': 1, 'off': 0.

Enables MPE Fec High Priority. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'on': 1, 'off': 0.

Enables timeslicing High Priority. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'on': 1, 'off': 0.

Enables timeslicing High Priority. Cannot be set if pt3080ModeMipControl is on(1). Enumeration: 'on': 1, 'off': 0.

SFN delay offset

The transport stream control identifier

Enables transport stream control of modulator Enumeration: 'on': 1, 'off': 0.

Enables MFN mode keep null packets option Enumeration: 'on': 1, 'off': 0.

Current network delay of HP TS

Minimum network delay of HP TS seen since last reset

Maximum network delay of HP TS seen since last reset

Maximum allowed network delay, as received from MIP

Difference between Actual Network Delay and Max. Allowed Network Delay

Current network delay of LP TS

Minimum network delay of LP TS seen since last reset

Maximum network delay of LP TS seen since last reset

Maximum allowed network delay, as received from MIP

Difference between Actual Network Delay and Max. Allowed Network Delay

Reset network delay. Always reads back as noop(0) Enumeration: 'reset': 1, 'noop': 0.

Default MIP value for Output Power Level. Cannot be set if pt3080ModeMipControlOutputPower is on(1)

Default MIP value for Output SFN Time Offset. Cannot be set if pt3080ModeMipControlOutputTimeOffset is on(1)

Default MIP value for Output Cell ID. Cannot be set if pt3080ModeMipControlOutputCellId is on(1)

Default MIP value for Output frequency Offset. Cannot be set if pt3080ModeMipControlOutputFreqOffset is on(1)

The MIP value for SFN maximum delay

Enables transport stream control of ModeDefaultMIPOutputPower Enumeration: 'on': 1, 'off': 0.

Enables transport stream control of ModeDefaultMIPOutputTimeOffset Enumeration: 'on': 1, 'off': 0.

Enables transport stream control of ModeDefaultMIPOutputCellId Enumeration: 'on': 1, 'off': 0.

Enables transport stream control of ModeDefaultMIPOutputFreqOffset Enumeration: 'on': 1, 'off': 0.

Control wheter to react on broadcast tx id. Enumeration: 'on': 1, 'off': 0.

monitors the Reference signal direction. state: - inputOutput[inputOutput_INPUT] - inputOutput[inputOutput_OUTPUT] Enumeration: 'input': 0, 'output': 1.

Defines the input reference synchronisation source. If the value AUTO is chosen, the source is chosen automatically between available sources. The order of choice is GPS->EXT10MHz->INT. If the value EXT is chosen, the external clock is chosen as source If the value INT is chosen, the internal clock is chosen as source. If the value GPS is chosen, the GNSS 1PPS clock is chosen as source. Enumeration: 'int': 2, 'auto': 0, 'ext': 1, 'gps': 3.

Defines the external 10 MHz input reference synchronisation source impedance. The value is either 50O or high impedance. Enumeration: 'o-50': 0, 'himp': 1.

Defines the external 1 PPS input reference synchronisation source impedance. The value is either 50ohm or high impedance. Enumeration: 'o-50': 0, 'himp': 1.

Defines the trigger edge of the external 1PPS input reference clock. The value is either RISING or FALLING. Enumeration: 'falling': 1, 'rising': 0.

Defines the trigger level of the external 1PPS input reference clock

Defines the external 10 MHz input reference synchronisation source impedance. The value is either 50O or high impedance.

The holdover delay for input reference source 10MHz failure is forever Enumeration: 'yes': 1, 'no': 0.

Defines the external 1 PPS input reference synchronisation source impedance. The value is either 50ohm or high impedance.

The holdover delay for input reference source 1 pps failure is forever Enumeration: 'yes': 1, 'no': 0.

returns the current input reference synchronisation source. Enumeration: 'ndel': 7, 'gnss': 4, 'internal': 3, 'external': 0, 'external-10mhz': 1, 'external-1pps': 2, 'asi2': 6, 'asi1': 5.

The TS-Primary input source connector selected Enumeration: 'satRecv': 6, 'asi-in-1': 0, 'asi-in-2': 1, 'demodulator-2': 3, 'demodulator-1': 2, 'tsoip-rx1': 4, 'tsoip-rx2': 5.

The TS-Secondary input source connector selected Enumeration: 'satRecv': 6, 'asi-in-1': 0, 'asi-in-2': 1, 'demodulator-2': 3, 'demodulator-1': 2, 'tsoip-rx1': 4, 'tsoip-rx2': 5.

The policy to use for TS auto routing Enumeration: 'only-use-primary': 0, 'use-primary-if-available': 2, 'only-use-secondary': 1, 'use-any-available': 3.

The delay before performing the actual substitution where TS-Primary -> TS-LP and TS-Secondary -> TS-HP

The delay before performing the actual substitution where TS-Primary -> TS-HP and TS-Secondary -> TS-LP

The time ASI Holdover will be active, if seamless ASI switching is not possible

The Max delay between the Program Association Table (PAT) on the incomming transport stream.

Enables TS switching if the Max delay between PAT table updates has been exceeded. Enumeration: 'on': 1, 'off': 0.

The TS-ID value expected on the incoming TS stream.

Enables TS switching if the TS-ID is not the expected value. Enumeration: 'on': 1, 'off': 0.

The NW-ID value expected on the incoming TS stream.

Enables TS switching if the NW-ID is not the expected value. Enumeration: 'on': 1, 'off': 0.

The expected stuffing rate on the incoming TS stream.

Enables TS switching if the Stuffing rate is over the expected value. Enumeration: 'on': 1, 'off': 0.

The Max STS jitter on the TS-Primary

The Max delay between the Program Association Table (PAT) on the incomming transport stream.

Enables TS switching if the Max delay between PAT table updates has been exceeded. Enumeration: 'on': 1, 'off': 0.

The TS-ID value expected on the incoming TS stream.

Enables TS switching if the TS-ID is not the expected value. Enumeration: 'on': 1, 'off': 0.

The NW-ID value expected on the incoming TS stream.

Enables TS switching if the NW-ID is not the expected value. Enumeration: 'on': 1, 'off': 0.

The expected stuffing rate on the incoming TS stream.

Enables TS switching if the Stuffing rate is over the expected value. Enumeration: 'on': 1, 'off': 0.

The Max STS jitter on the TS-Secondary

The current state for TS-Primary. Unavailable means violation of alarms. Enumeration: 'available': 0, 'unavailable': 1, 'nosync': 2.

The current state for TS-Secondary. Unavailable means violation of alarms. Enumeration: 'available': 0, 'unavailable': 1, 'nosync': 2.

The input source currently On Air. (TS-HP) Enumeration: 'satRecv': 6, 'asi-in-1': 0, 'asi-in-2': 1, 'demodulator-2': 3, 'demodulator-1': 2, 'tsoip-rx1': 4, 'tsoip-rx2': 5.

The input source currently used as backup. (TS-LP) Enumeration: 'satRecv': 6, 'asi-in-1': 0, 'asi-in-2': 1, 'demodulator-2': 3, 'demodulator-1': 2, 'tsoip-rx1': 4, 'tsoip-rx2': 5.

Reflects the effective ASI Autorouting Policy Enumeration: 'prefer-primary': 2, 'only-primary': 0, 'only-secondary': 1, 'seamless': 4, 'any-available': 3.

Current bitrate for On Air TS. (TS-HP)

Current number of packets buffered for On Air TS (TS-HP)

Current size of packets for On Air TS (TS-HP)

Current NULL stuffing as a percentage of the current bitrate for On Air TS (TS-HP)

Current Transport Stream ID for On Air TS. (TS-HP)

Current Network ID for On Air TS. (TS-HP)

Current bitrate for Backup TS. (TS-LP)

Current number of packets buffered for Backup TS. (TS-LP)

Current size of packets for Backup TS. (TS-LP)

Current NULL stuffing as a percentage of the current bitrate for Backup TS. (TS-LP)

Current Transport Stream ID for Backup TS. (TS-LP)

Current Network ID for Backup TS. (TS-LP)

Current STS jitter on the TS-Primary.

The Maximum STS jitter value seen on the TS-Primary

The minimum STS jitter value seen on the TS-Primary

Reset the pt3080InputTSPrimaryStsJitterMax and pt3080InputTSPrimaryStsJitterMin values Enumeration: 'noop': 0, 'reset-min-max': 1.

Current STS jitter on the TS-Secondary

The Maximum STS jitter value seen on the TS-Secondary

The minimum STS jitter value seen on the TS-Secondary

Reset the pt3080InputTSSecondaryStsJitterMax and pt3080InputTSSecondaryStsJitterMin values Enumeration: 'noop': 0, 'reset-min-max': 1.

The minimum delay margin of the incoming TS stream.

Enables TS switching if the Minimum Delay margin is not according to the expected value. Enumeration: 'on': 1, 'off': 0.

The minimum delay margin of the incoming TS stream.

Enables TS switching if the Minimum Delay margin is not according to the expected value. Enumeration: 'on': 1, 'off': 0.

The maximum seconds of missing mip information from the incoming TS stream.

Enables TS switching if the Maximum missing mip is not according to the expected value. Enumeration: 'on': 1, 'off': 0.

The maximum seconds of missing mip information from the incoming TS stream.

Enables TS switching if the Maximum missing mip is not according to the expected value. Enumeration: 'on': 1, 'off': 0.

Type of TCXO/OCXO Enumeration: 'tcxo-int': 0, 'ocxo-pt3710-10': 1, 'ocxo-pt3710-20': 2.

Calibration Date

Calibration SW Version

Control RF output mode Enumeration: 'standby': 1, 'normal': 0.

Output RF frequency

Sets the output level in 0.01dB steps, 0dB is +6dBm on IF, 0dBm on RF

Output Bandwidth

Channel settings

The values of pt3080OutputRfFrequency, pt3080OutputBandwidth and pt3080OutputChannel are synchronized aaccording to freq = (bw * channel) + 306000000. Enumeration: 'not-synchronized': 0, 'synchronized': 1.

Output mute. When set the mute reason UserRequest is ORed into the mute reason set. When read it is the logical OR of all mute reasons Enumeration: 'on': 1, 'off': 0.

Control RF output polarity Enumeration: 'inv': 1, 'norm': 0.

The desired output power level.

Output RF frequency offset

Control IF output Enumeration: 'yes': 1, 'no': 0.

Output Frequency for I/F

Control IF output polarity Enumeration: 'inv': 1, 'norm': 0.

Output Level for I/F

Effective RF Output Level

Actual RF Output Level

Detected Output Level for RF

Limit to how much lower the detected RF output level can be than the configured level.

Controls whether the lower limit for RF output level is enforced. Enumeration: 'enable': 1, 'disable': 0.

Limit to how much higher the detected RF output level can be than the configured level.

Controls whether the higher limit for RF output level is enforced. Enumeration: 'enable': 1, 'disable': 0.

Controls whether the ALC system is enabled or disabled. Enumeration: 'enable': 1, 'disable': 0.

Controls which sense port is used by the ALC system if the ALC is enabled. Enumeration: 'rfsense2': 1, 'rfsense1': 0.

ALC setpoint for RF Sense Port 1

ALC setpoint for RF Sense Port 2

Status for whether the ALC system is enabled or disabled. Enumeration: 'enable': 1, 'disable': 0.

Information on the state of the ALC system.

Control whether Cable Level loss compensation should be enabled Enumeration: 'auto': 2, 'none': 0, 'const': 1.

Constant level offset to add to RF Output level. Only used if mode is Constant.

Frequency depedent level offset to add to RF Output level. Only used if mode is Automatic.

Frequency depedent level offset to add to RF Output level. Only used if mode is Automatic.

Frequency depedent level offset to add to RF Output level. Only used if mode is Automatic.

Frequency depedent level offset to add to RF Output level. Only used if mode is Automatic.

Frequency depedent level offset to add to RF Output level. Only used if mode is Automatic.

Frequency depedent level offset to add to RF Output level. Only used if mode is Automatic.

Returns the current locking state of the GPS system. The value LOCKED indicates that the GPS system is locked to a sufficient number of satellites to perform well. UNLOCKED indicates that it is not. For the GPS system to perform well at least 4 satellites must be visible with a proper signal to noise ratio. Enumeration: 'locked': 0, 'unlocked': 1.

Returns the number of currently visible satellites via the built-in GPS receiver. A satellite is visible if at all detectable by the GPS system i.e. regardless of signal to noise ratio. Note that the upper value N can change with the launch of new satellites. For some time, however, the GPS system has had a total of 24 satellites.

Returns the number of currently tracked satellites via the GPS receiver.

Defines the bias to be either on or off for the GPS antenna DC supply (5V or 3V DC). An active GPS antenna requires a power supply i.e. requires this parameter to set to ON. Enumeration: 'on': 1, 'off': 0.

Returns - as a string - the current longtitude derived from the received GPS signal(s). The string format is DDD MM SS C. according to the following: - DD denotes degrees in the intervals [0 .. 180]. MM and SS denote minutes/seconds in the interval [0 .. 59]. C denotes E, W (East, West).

Returns - as a string - the current latitude derived from the received GPS signal(s). The string format is DD MM SS C. according to the following: - DD denotes degrees in the intervals [0 .. 90]. MM and SS denote minutes/seconds in the interval [0 .. 59]. C denotes N, S (North, South).

Returns - as a string - the current altitude derived from the received GPS signal(s). The string format is HHHH.c;. according to the following: HHHH.c denotes the altitude in metres with one digit after the comma. The altitude can be negative.

Returns the GPS chip firmware version as a string.

Defines the GPS holdover time. This value is ignored if the holdover forever (see below) is set to YES If the GPS locking is lost the system is allowed to continue operating for holdover time seconds using the internal GPS chip oscillator. If - when the holdover time interval expires - the GPS locking it still lost, the GPS operation will be maintained using external timing if present. If external timing is not present the GPS operation will be maintained using the internal motherboard oscillator.

Defines whether the GPS system is allowed to operate infinitely (YES) following loss of GPS locking using the internal GPS chip oscillator or not (NO).In case NO is chosen the GPS holdover time applies. Enumeration: 'yes': 1, 'no': 0.

Defines the antenna cable compensation delay. If the GPS antenna is situated far away from the receiver itself the signal will be delayed and must be compensated.

Returns a string describing the GPS state. For informational purposes.

Returns the average signal to noise ratio of all visible satellites via the built-in GPS receiver

Defines the gps antenna bias voltage. An active GPS antenna requires a power supply of either 3V or 5V. Enumeration: 'gpsant-5v': 0, 'gpsant-33v': 1.

Controls whether GPS satellites are used to obtain position and timing information. Enumeration: 'enable': 1, 'disable': 0.

Controls whether GLONASS satellites are used to obtain position and timing information. Enumeration: 'enable': 1, 'disable': 0.

Controls whether GALILEO satellites are used to obtain position and timing information. Enumeration: 'enable': 1, 'disable': 0.

Controls whether COMPASS satellites are used to obtain position and timing information. Enumeration: 'enable': 1, 'disable': 0.

Specifies the maximum time accepted between received TS packages.

Specifies the minimum time incoming data is buffered. The value configured might be modified by FEC row/column sized on the incoming data.

Specifies which virtual LAN interface to receive IP/UDP packets from. Enumeration: 'tlan': 2, 'flan': 0, 'plan': 4, 'alan': 1, 'blan': 3.

Enables the reception of Multicast IP/UDP packets with transport stream data to be forward into the modulator. If disabled, only unicast IP/UDP packets are considdered. Enumeration: 'on': 1, 'off': 0.

Selects which protocol to expect incoming packets to have. Enumeration: 'auto': 2, 'udp': 0, 'rtp': 1.

Specifies which UDP port number to receive IP/UDP packets from.

Enables the reception of IP/UDP packets with transport stream data to be forward into the modulator. Enumeration: 'enable': 1, 'disable': 0.

Specifies limit for the Packet Error Ratio. If the limit is exceeded and alarm is raised.

The current status of the receiver. Locked means minimum of 3 IP/UDP frames received per second. Enumeration: 'disabled': 2, 'locked': 0, 'unlocked': 1.

The current receive IP address for the TSoIP interface.

The number of sequence errors on this channel on the TSoIP interface.

Shows the current error ratio of uncoming traffic for this UDP port.

The number of lost IP frames on the channel on the TSoIP interface. The sequence numbers of frames employed by the RTP protocol are used to determine this statistic.

The number of corrected IP frames (via FEC) on this cannel on the TSoIP interface.

The curent FEC Column (L) number for this cannel on the TSoIP interface.

The curent FEC Row (D) number for this cannel on the TSoIP interface.

The curent number of TS packets per IP frames on this cannel on the TSoIP interface.

Shows the current bitrate of uncoming traffic for this UDP port.

The curent queue size for this cannel on the TSoIP interface.

The current latency incurrent by queue size on this channel on the TSoIP interface.

The curent size of TS packets on this cannel on the TSoIP interface. Usually 188 or 204.

The number of IP frames lost on the channel on the TSoIP interface due to overrun. Overrun happens when the outgoing rate of the modulator is lower that the incoming rate of TSoIP data.

Specifies the maximum time accepted between received TS packages.

Specifies the minimum time incoming data is buffered. The value configured might be modified by FEC row/column sized on the incoming data.

Specifies which virtual LAN interface to receive IP/UDP packets from. Enumeration: 'tlan': 2, 'flan': 0, 'plan': 4, 'alan': 1, 'blan': 3.

Enables the reception of Multicast IP/UDP packets with transport stream data to be forward into the modulator. If disabled, only unicast IP/UDP packets are considdered. Enumeration: 'on': 1, 'off': 0.

Selects which protocol to expect incoming packets to have. Enumeration: 'auto': 2, 'udp': 0, 'rtp': 1.

Specifies which UDP port number to receive IP/UDP packets from.

Enables the reception of IP/UDP packets with transport stream data to be forward into the modulator. Enumeration: 'enable': 1, 'disable': 0.

Specifies limit for the Packet Error Ratio. If the limit is exceeded and alarm is raised.

The current status of the receiver. Locked means minimum of 3 IP/UDP frames received per second. Enumeration: 'disabled': 2, 'locked': 0, 'unlocked': 1.

The current receive IP address for the TSoIP interface.

The number of sequence errors on this channel on the TSoIP interface.

Shows the current error ratio of uncoming traffic for this UDP port.

The number of lost IP frames on the channel on the TSoIP interface. The sequence numbers of frames employed by the RTP protocol are used to determine this statistic.

The number of corrected IP frames (via FEC) on this cannel on the TSoIP interface.

The curent FEC Column (L) number for this cannel on the TSoIP interface.

The curent FEC Row (D) number for this cannel on the TSoIP interface.

The curent number of TS packets per IP frames on this cannel on the TSoIP interface.

Shows the current bitrate of uncoming traffic for this UDP port.

The curent queue size for this cannel on the TSoIP interface.

The current latency incurrent by queue size on this channel on the TSoIP interface.

The curent size of TS packets on this cannel on the TSoIP interface. Usually 188 or 204.

The number of IP frames lost on the channel on the TSoIP interface due to overrun. Overrun happens when the outgoing rate of the modulator is lower that the incoming rate of TSoIP data.

Selects the source to be monitored on the ASI monitor output. Enumeration: 'asi-in1': 0, 'ts-lp': 7, 'backplane1': 8, 'backplane2': 9, 'ts-hp': 6, 'asi-in2': 1, 'aux2': 3, 'aux1': 2, 'tsoiprx1': 4, 'tsoiprx2': 5.

Enable or disable the generation of monitor data over TSoIP. Enumeration: 'enable': 1, 'disable': 0.

Selects the source to be monitored on the TSoIP monitor output. Enumeration: 'asi-in1': 0, 'ts-lp': 7, 'backplane1': 8, 'backplane2': 9, 'ts-hp': 6, 'asi-in2': 1, 'aux2': 3, 'aux1': 2, 'tsoiprx1': 4, 'tsoiprx2': 5.

Selects the destination IP address of the data to be monitored on the TSoIP monitor output.

Selects the destination UDP Port number of the data to be monitored on the TSoIP monitor output.

Selects the protocol to be used on the TSoIP monitor output. Enumeration: 'udp': 0, 'rtp': 1.

Enable or disable FEC protocol on the output data from the TSoIP Monitor. Enumeration: 'enable': 1, 'disable': 0.

Selects the FEC protocoll Column number (L) of the data to be monitored on the TSoIP monitor output.

Selects the FEC protocol Row number (D) of the data to be monitored on the TSoIP monitor output.

Selects the FEC protocol Skew (non block alignment of FEC Frame) of the data to be monitored on the TSoIP monitor output.

Retain or discard Null packets of the generation of monitor data over TSoIP. Enumeration: 'enable': 1, 'disable': 0.

Set the number of TS packets to send per IP frame on the TSoIP monitor output.

Generate UDP checksum in the outgoing packets of the TSoIP Monitor. Enumeration: 'enable': 1, 'disable': 0.

Selects the value of the TOS/DSCP field in IP packets to be sent on the TSoIP monitor output.

Selects the value of the TTL (Time-To-Live) field in IP packets to be sent on the TSoIP monitor output.

Artificially generate an error rate as a percentage of frames lost on the TSoIP monitor output.

Specifies which virtual LAN interface to transmit Multicast IP/UDP packets out via. Enumeration: 'tlan': 2, 'flan': 0, 'plan': 4, 'alan': 1, 'blan': 3.

The current rate IP packets traffic to be sent on the TSoIP monitor output.

The number of IP packets traffic generated but lost on the TSoIP monitor output.

The current TS packet size (188 or 204) on the TSoIP monitor output.

controls the test signal generation. This cannot be used when network mode is SFN. Only a subset is available in repeater mode. test signal output state: - testSignalsArray[testSignals_OFF] Normal operation. No test signal. - testSignalsArray[testSignals_SCAR] A single carrier output is provided. - testSignalsArray[testSignals_SWEEP2] A test signal with full spectrum bandwidth and a 3dB peak to average power ratio. (OFDM PPR-3). - testSignalsArray[testSignals_PRBSON] Forced transmission of stuffing data only (null packets) irrespective of the status of the MPEG-2 transport stream input. - testSignalsArray[testSignals_PRBSAUTO] Automatic transmission of spectrum based on stuffing data when no MPEG-2 TS input is available. Enumeration: 'off': 0, 'scar': 1, 'sweep2': 2, 'prbs-auto': 4, 'prbs-on': 3.

Controls whether the test signal shall reconnect after reset. This value is saved in non-volatile memory and thus survives a reboot. - onOffArray[TEXT_INDEX_OFF] The selected test signal will be set to OFF after reset. - onOffArray[TEXT_INDEX_ON] The selected test signal will be output after reset. Enumeration: 'on': 1, 'off': 0.

Control level of the single carrier test signal.

Control frequency offset of the single carrier test signal.

This table contains the group alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current GroupAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the ASI TS-Primary alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current ASITSPrimaryAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the ASI alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current ASITSSecondaryAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the SFN alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current SFNAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the Reference alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current ReferenceAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the RF alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current RFAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the GPS alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current GPSAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the TSoIP alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current TSoIPAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the External alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current ExternalAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the HW Monitor alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current HWMonitorAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the Communication alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current CommsAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the ASI alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current ASIAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the Demodulator alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current DemodulatorAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the Internal alarms

An entry for the alarms

Unique ID for this alarm

Description for this alarm

Current InternalAlarm state condition Enumeration: 'off': 0, 'activated': 1.

Will the current alarm generate an event in the eventlog Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay1 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm activate relay2 Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate a trap Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm generate an email Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm turn Alarm LED on frontpanel on Enumeration: 'disabled': 0, 'enabled': 1.

Will the current alarm mute output Enumeration: 'none': 0, 'reboot': 2, 'mute': 1.

This table contains the presets

An entry for the presets

Unique number for this preset

Name for this preset

Install this preset into current running parameter set. Value will always read as 0 and setting it to 0 has no effect.

Store the currently running parameter set into this preset Value will always read as 0 and setting it to 0 has no effect.

This table contains the group alarms

An entry for the alarms

Unique number for this event

Unique ID for this type of event

Timestamp for this event

Text for this event

Clear the entire eventlog by setting the value to 1. Enumeration: 'clear': 1, 'noop': 0.

Enable eventlog by setting the value to 1. Enumeration: 'on': 1, 'off': 0.

Set eventlog mode to FIFO for keeping the newest entries. Set eventlog mode to FULL for keeping the oldest entries. Enumeration: 'full': 1, 'fifo': 0.

The static IP address for this interface. Will be used if DHCP is disabled or unavailable.

The static IP netmask for this interface. Will be used if DHCP is disabled or unavailable.

Enable/Disable DHCP client on this interface. Enumeration: 'client': 1, 'off': 0.

The current IP address for this interface.

The current IP netmask for this interface.

The static IP address for this interface. Will be used if DHCP is disabled or unavailable.

The static IP netmask for this interface. Will be used if DHCP is disabled or unavailable.

The current IP address for this interface.

The current IP netmask for this interface.

The static IP address for this interface. Will be used if DHCP is disabled or unavailable.

The static IP netmask for this interface. Will be used if DHCP is disabled or unavailable.

The current IP address for this interface.

The current IP netmask for this interface.

The IP address of DNS server 1.

The Current IP address of DNS server 1.

The IP address of DNS server 2.

The Current IP address of DNS server 2.

The IP address of DNS server 3.

The Current IP address of DNS server 3.

The static DNS domain name for the device. Will be used if DHCP is disabled or unavailable.

The current DNS domain name for the device.

The static hostname for the device. Will be used if DHCP is disabled or unavailable.

The static hostname for the device. Will be used if DHCP is disabled or unavailable.

The static IP address for the default router (gateway). Will be used unless DHCP is enabled and the DHCP server is configured to include a default router address.

The Current IP address for the default router (gateway).

The DNS name or IP address of the NTP server.

The Current IP address of the NTP server.

The IP address of the Email (SMTP) server.

The email address of the receipiant of alarm emails.

The TCP port number used for Web Service.

The TCP port number used for SCPI Service.

The Baudrate used for SCPI Service on serial port. Enumeration: 'r19200': 3, 'r115200': 6, 'r57600': 5, 'r4800': 1, 'r9600': 2, 'r2400': 0, 'r38400': 4.

The UDP port number used for RIP Service.

The Interface used for SCPI Service on serial port. Enumeration: 'rs232': 0, 'rs485': 1, 'rs485hd': 2.

Current access mode allowed: Remote: SNMP via Ethernet, Local: Frontpanel Enumeration: 'local-disable-set': 1, 'remote': 0.

Timeout (in minutes) before local mode reverts to remote mode.

Current time left (in seconds) before local mode reverts to remote mode.

The access password for Observer level access. Will always read as empty.

The access password for Operator level access. Will always read as empty.

The access password for Administrator level access. Will always read as empty.

The UDP port number used for SNMP Service.

The Read-only community string used to access the SNMP Service.

The Read-Write community string used to access the SNMP Service.

The Trap community string used when sending SNMP Traps.

The destination IP address for the SNMP traps.

The UDP port number used for Trap destination .

Enable/Disable DHCP client on this interface. Enumeration: 'client': 1, 'off': 0.

Enable/Disable DHCP client on this interface. Enumeration: 'client': 1, 'off': 0.

Enable/Disable DHCP client on this interface. Enumeration: 'client': 1, 'off': 0.

The Physical Ethernet Interface of this (virtual) interface. Enumeration: 'eth4': 4, 'eth3': 3, 'eth2': 2, 'eth1': 1, 'eth0': 0.

The Physical Ethernet Interface of this (virtual) interface. Enumeration: 'eth4': 4, 'eth3': 3, 'eth2': 2, 'eth1': 1, 'eth0': 0.

The Physical Ethernet Interface of this (virtual) interface. Enumeration: 'eth4': 4, 'eth3': 3, 'eth2': 2, 'eth1': 1, 'eth0': 0.

Enable/Disable broadcast (and multicast) storm Protection. This will limit the network ingress rate on physical Ethernet port 0 and 1 to roughly 100mbit/s. Enumeration: 'on': 1, 'off': 0.

The time interval between unsolicited IGMPv2/v1 reports being sent. See RFC2236. The number of such report being sent is controlled by the Query Robustness Count.

The time interval between unsolicited IGMPv3 reports being sent. See RFC3376. The number of such report being sent is controlled by the Query Robustness Count.

The Number of Query Replies sent. The higher a number, the more robust IGMP setup is. At the cost of traffic on the network. Note: Changing this parameter doesnt take effect on a network interface until it has (re-)enabled.

Will the ports on the switch in the backplane forward LAN traffic to each other or will they be separated and only forward traffic to/from the modulator/repeater. Enumeration: 'on': 1, 'off': 0.

Select which IGMP Version to use. Enumeration: 'auto': 0, 'v2': 2, 'v3': 3, 'v1': 1.

The IP Multicast address for this interface.

Enable/Disable VLAN on this interface. Enumeration: 'enable': 1, 'disable': 0.

VLAN ID to use on this interface, if VLAN is enabled. Please note that VLAN ID 4001 and 4002 are used for internal switching and thus cannot be used on any interface.

Enable/Disable SNMP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable SCPI service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable TSoIP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable RIP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

The IP Multicast address for this interface.

Enable/Disable VLAN on this interface. Enumeration: 'enable': 1, 'disable': 0.

VLAN ID to use on this interface, if VLAN is enabled. Please note that VLAN ID 4001 and 4002 are used for internal switching and thus cannot be used on any interface.

Enable/Disable SNMP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable SCPI service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable TSoIP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable WEB (http) service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable RIP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

The IP Multicast address for this interface.

Enable/Disable VLAN on this interface. Enumeration: 'enable': 1, 'disable': 0.

VLAN ID to use on this interface, if VLAN is enabled. Please note that VLAN ID 4001 and 4002 are used for internal switching and thus cannot be used on any interface.

Enable/Disable SNMP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable SCPI service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable TSoIP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable Web (http) service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable RIP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable this interface. Enumeration: 'enable': 1, 'disable': 0.

The Physical Ethernet Interface of this (virtual) interface. Enumeration: 'eth4': 4, 'eth3': 3, 'eth2': 2, 'eth1': 1, 'eth0': 0.

The static IP address for this interface. Will be used if DHCP is disabled or unavailable.

The static IP netmask for this interface. Will be used if DHCP is disabled or unavailable.

The IP Multicast address for this interface.

Enable/Disable VLAN on this interface. Enumeration: 'enable': 1, 'disable': 0.

VLAN ID to use on this interface, if VLAN is enabled. Please note that VLAN ID 4001 and 4002 are used for internal switching and thus cannot be used on any interface.

Enable/Disable SNMP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable SCPI service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable TSoIP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable Web (http) service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable RIP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

The current IP address for this interface.

The current IP netmask for this interface.

The IP Multicast Source Filter address no 1 for this interface.

The IP Multicast Source Filter address no 2 for this interface.

The IP Multicast Source Filter address no 3 for this interface.

The IP Multicast Source Filter address no 4 for this interface.

The IP Multicast Source Filter address no 5 for this interface.

The IP Multicast Source Filter address no 6 for this interface.

Specifies whether the Multicast Source Filter IP Address list is: SFINCLUDE: ONLY receive multicast frames from the source addresses in the list. SFEXCLUDE: Receive all multicast frames EXCEPT from the source addresses in the list. Enumeration: 'sfexclude': 1, 'sfinclude': 0.

Specifies whether the Multicast Source Filter IP Address list is: SFINCLUDE: ONLY receive multicast frames from the source addresses in the list. SFEXCLUDE: Receive all multicast frames EXCEPT from the source addresses in the list. Enumeration: 'sfexclude': 1, 'sfinclude': 0.

Specifies whether the Multicast Source Filter IP Address list is: SFINCLUDE: ONLY receive multicast frames from the source addresses in the list. SFEXCLUDE: Receive all multicast frames EXCEPT from the source addresses in the list. Enumeration: 'sfexclude': 1, 'sfinclude': 0.

Specifies whether the Multicast Source Filter IP Address list is: SFINCLUDE: ONLY receive multicast frames from the source addresses in the list. SFEXCLUDE: Receive all multicast frames EXCEPT from the source addresses in the list. Enumeration: 'sfexclude': 1, 'sfinclude': 0.

The IP Multicast Source Filter address no 1 for this interface.

The IP Multicast Source Filter address no 2 for this interface.

The IP Multicast Source Filter address no 3 for this interface.

The IP Multicast Source Filter address no 4 for this interface.

The IP Multicast Source Filter address no 5 for this interface.

The IP Multicast Source Filter address no 6 for this interface.

The IP Multicast Source Filter address no 1 for this interface.

The IP Multicast Source Filter address no 2 for this interface.

The IP Multicast Source Filter address no 3 for this interface.

The IP Multicast Source Filter address no 4 for this interface.

The IP Multicast Source Filter address no 5 for this interface.

The IP Multicast Source Filter address no 6 for this interface.

The IP Multicast Source Filter address no 1 for this interface.

The IP Multicast Source Filter address no 2 for this interface.

The IP Multicast Source Filter address no 3 for this interface.

The IP Multicast Source Filter address no 4 for this interface.

The IP Multicast Source Filter address no 5 for this interface.

The IP Multicast Source Filter address no 6 for this interface.

This table contains the static routing table entries

An entry for the static network routing table

Unique ID for this static route entry

Type of a Route table entry. Enumeration: 'unused': 0, 'physicalif': 2, 'drop': 4, 'recursive': 3, 'normal': 1.

The IP address part of prefix for a route table entry. If the address is 0.0.0.0, the entry will not be used.

The number of bits in the network part of the prefix for route table entry $. If the number is 0 (zero), the entry will not be used.

The target IP address for a route table entry. Only used if pt3080CommsStaticRouteType is normal(1) or recursive(3). If the target address is 0.0.0.0, the entry will not be used.

The Physical Ethernet Interface to use for a Route table entry. Only used when pt3080CommsStaticRouteType is physicalif(2). Enumeration: 'eth4': 4, 'eth3': 3, 'eth2': 2, 'eth1': 1, 'eth0': 0.

The destination 2 IP address for the SNMP traps.

The UDP port number used for Trap destination 2.

The destination 3 IP address for the SNMP traps.

The UDP port number used for Trap destination 3.

The destination 4 IP address for the SNMP traps.

The UDP port number used for Trap destination 4.

The destination 5 IP address for the SNMP traps.

The UDP port number used for Trap destination 5.

Enable/Disable DHCP client on this interface. Enumeration: 'client': 1, 'off': 0.

The Physical Ethernet Interface of this (virtual) interface. Enumeration: 'eth4': 4, 'eth3': 3, 'eth2': 2, 'eth1': 1, 'eth0': 0.

The static IP address for this interface. Will be used if DHCP is disabled or unavailable.

The static IP netmask for this interface. Will be used if DHCP is disabled or unavailable.

The IP Multicast address for this interface.

Enable/Disable VLAN on this interface. Enumeration: 'enable': 1, 'disable': 0.

VLAN ID to use on this interface, if VLAN is enabled. Please note that VLAN ID 4001 and 4002 are used for internal switching and thus cannot be used on any interface.

Enable/Disable SNMP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable SCPI service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable TSoIP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable Web (http) service on this interface. Enumeration: 'enable': 1, 'disable': 0.

Enable/Disable RIP service on this interface. Enumeration: 'enable': 1, 'disable': 0.

The current IP address for this interface.

The current IP netmask for this interface.

The IP Multicast Source Filter address no 1 for this interface.

The IP Multicast Source Filter address no 2 for this interface.

The IP Multicast Source Filter address no 3 for this interface.

The IP Multicast Source Filter address no 4 for this interface.

The IP Multicast Source Filter address no 5 for this interface.

The IP Multicast Source Filter address no 6 for this interface.

Specifies whether the Multicast Source Filter IP Address list is: SFINCLUDE: ONLY receive multicast frames from the source addresses in the list. SFEXCLUDE: Receive all multicast frames EXCEPT from the source addresses in the list. Enumeration: 'sfexclude': 1, 'sfinclude': 0.

Enable/Disable this interface. Enumeration: 'enable': 1, 'disable': 0.

Controls the Demodulators follow mode. Enumeration: 'enable': 1, 'disable': 0.

Status on the availability of Demodulator 1 Enumeration: 'yes': 1, 'no': 0.

Demodulator 1 firmware version string

Controls which TS demodulator 1 shall output Enumeration: 'hp': 0, 'lp': 1.

Lower limit for MER Level

Upper limit for Pre-Virterbi Bit Error Rate

Upper limit for Post-Virterbi Bit Error Rate

Received signal locked status on Demodulator 1 Enumeration: 'locked': 0, 'unlocked': 1.

Number of uncorrected packets received in Demodulator 1 since boot or since counter was last cleared.

Current MER level for Demodulator 1

Current Pre-Virterbi Bit Error Rate for Demodulator 1

Current Post-Virterbi Bit Error Rate for Demodulator 1

Guard Interval for the received signal on Demodulator 1 Enumeration: 'g1-32': 0, 'g1-4': 3, 'g1-16': 1, 'g1-8': 2.

IFFT for the received signal on Demodulator 1 Enumeration: 'f2k': 0, 'f4k': 1, 'f8k': 2.

Constellation for the received signal on Demodulator 1 Enumeration: 'qpsk': 0, 'qam16': 1, 'qam64': 2.

Hierarchy for the received signal on Demodulator 1 Enumeration: 'h-4': 3, 'none': 0, 'h-1': 1, 'h-2': 2.

High Priority Code Rate for the received signal on Demodulator 1 Enumeration: 'r3-4': 2, 'r1-2': 0, 'r2-3': 1, 'r5-6': 3, 'r7-8': 4.

High Priority Code Rate for the received signal on Demodulator 1 Enumeration: 'r3-4': 2, 'r1-2': 0, 'r2-3': 1, 'r5-6': 3, 'r7-8': 4.

Deep Interleaver for the received signal on Demodulator 1 Enumeration: 'on': 1, 'off': 0.

High Priority MPE/FEC mode for the received signal on Demodulator 1 Enumeration: 'on': 1, 'off': 0.

Low Priority MPE/FEC mode for the received signal on Demodulator 1 Enumeration: 'on': 1, 'off': 0.

High Priority timeslicing mode for the received signal on Demodulator 1 Enumeration: 'on': 1, 'off': 0.

Low Priority timeslicing mode for the received signal on Demodulator 1 Enumeration: 'on': 1, 'off': 0.

Current Cell ID value for the received signal on Demodulator 1

DVB-H mode for the received signal on Demodulator 1 Enumeration: 'on': 1, 'off': 0.

Status on the availability of Demodulator 2 Enumeration: 'yes': 1, 'no': 0.

Demodulator 2 firmware version string

Controls which TS demodulator 2 shall output Enumeration: 'hp': 0, 'lp': 1.

Lower limit for MER Level

Upper limit for Pre-Virterbi Bit Error Rate

Upper limit for Post-Virterbi Bit Error Rate

Received signal locked status on Demodulator 2 Enumeration: 'locked': 0, 'unlocked': 1.

Number of uncorrected packets received in Demodulator 2 since boot or since counter was last cleared.

Current MER level for Demodulator 2

Current Pre-Virterbi Bit Error Rate for Demodulator 2

Current Post-Virterbi Bit Error Rate for Demodulator 2

Guard Interval for the received signal on Demodulator 2 Enumeration: 'g1-32': 0, 'g1-4': 3, 'g1-16': 1, 'g1-8': 2.

IFFT for the received signal on Demodulator 2 Enumeration: 'f2k': 0, 'f4k': 1, 'f8k': 2.

Constellation for the received signal on Demodulator 2 Enumeration: 'qpsk': 0, 'qam16': 1, 'qam64': 2.

Hierarchy for the received signal on Demodulator 2 Enumeration: 'h-4': 3, 'none': 0, 'h-1': 1, 'h-2': 2.

High Priority Code Rate for the received signal on Demodulator 2 Enumeration: 'r3-4': 2, 'r1-2': 0, 'r2-3': 1, 'r5-6': 3, 'r7-8': 4.

High Priority Code Rate for the received signal on Demodulator 2 Enumeration: 'r3-4': 2, 'r1-2': 0, 'r2-3': 1, 'r5-6': 3, 'r7-8': 4.

Deep Interleaver for the received signal on Demodulator 2 Enumeration: 'on': 1, 'off': 0.

High Priority MPE/FEC mode for the received signal on Demodulator 2 Enumeration: 'on': 1, 'off': 0.

Low Priority MPE/FEC mode for the received signal on Demodulator 2 Enumeration: 'on': 1, 'off': 0.

High Priority timeslicing mode for the received signal on Demodulator 2 Enumeration: 'on': 1, 'off': 0.

Low Priority timeslicing mode for the received signal on Demodulator 2 Enumeration: 'on': 1, 'off': 0.

Current Cell ID value for the received signal on Demodulator 1

DVB-H mode for the received signal on Demodulator 2 Enumeration: 'on': 1, 'off': 0.

selection of the operational mode for the linear adaptive precorrector
(note: legacy term used for backward compatibility. IDLE Equal to the mode named MONITORING in the WEB GUI ) Enumeration: 'idle': 0, 'continuous': 3, 'runtotarget': 2, 'single': 4, 'autorun': 1.

selection of the operational mode for the linear precorrector
(note: legacy term used for backward compatibility. MONITORING Equal to the mode named BYPASS in the WEB GUI ) Enumeration: 'monitoring': 0, 'adaptive': 2, 'static': 1.

selection of the operational mode for the non-linear adaptive precorrector
(note: legacy term used for backward compatibility. IDLE Equal to the mode named MONITORING in the WEB GUI ) Enumeration: 'idle': 0, 'continuous': 3, 'runtotarget': 2, 'single': 4, 'autorun': 1.

selection of the operational mode for the non-linear precorrector
(note: legacy term used for backward compatibility. MONITORING Equal to the mode named BYPASS in the WEB GUI ) Enumeration: 'monitoring': 0, 'adaptive': 2, 'static': 1.

PrecorrectorLastTurnAroundTime

PrecorrectorSecondsSinceLastUpdate

Number of bad/invalid sense counts, made by the linear adaptive precorrector.

Number of bad/invalid sense counts, made by the nonlinear adaptive precorrector.

Enable amplitude ripple as a trigger for the AUTORUN and RUNTOTARGET modes Enumeration: 'on': 1, 'off': 0.

Enable group delay as a trigger for the AUTORUN and RUNTOTARGET modes Enumeration: 'on': 1, 'off': 0.

Enable shoulder level (lower) as a trigger for the AUTORUN and RUNTOTARGET modes Enumeration: 'on': 1, 'off': 0.

Enable shoulder level (upper) as a trigger for the AUTORUN and RUNTOTARGET modes Enumeration: 'on': 1, 'off': 0.

Define a adaptive target level hysteresis for the amplitude ripple

Define a adaptive target level hysteresis for the group delay

Define a adaptive target level hysteresis for the lower shoulder

Define a adaptive target level hysteresis for the upper shoulder

PrecorrectorLinCleanrun

Number of iterations made by the linear adaptive precorrector.

PrecorrectorLinearLoadNeutral Enumeration: 'load': 1, 'noop': 0.

PrecorrectorLinearLoadFactory Enumeration: 'load': 1, 'noop': 0.

Level meassured at the linear sense input with offset defined by attenuation

Is linear sense input information valid

linear Precor state Enumeration: 'initialising-90': 12, 'auto-applying': 13, 'monitoring': 1, 'initialising-40': 7, 'initialising-0': 3, 'initialising-50': 8, 'initialising-60': 9, 'initialising-70': 10, 'initialising': 2, 'initialising-10': 4, 'not-running': 0, 'initialising-20': 5, 'completed': 14, 'initialising-80': 11, 'initialising-30': 6.

PrecorrectorLinearUpdateFactoryCurve Enumeration: 'noop': 0, 'update': 1.

Amplitude ripple

Group delay

Lower shoulder level

Upper shoulder level

Is amplitude ripple information valid

Is group delay information valid

Is Lower shoulder information valid

Is Upper shoulder information valid

PrecorrectorNlinCleanrun Enumeration: 'yes': 1, 'no': 0.

Number of iterations made by the nonlinear adaptive precorrector.

PrecorrectorNonlinearLoadNeutral Enumeration: 'load': 1, 'noop': 0.

PrecorrectorNonlinearLoadFactory Enumeration: 'load': 1, 'noop': 0.

Level meassured at the Nonlinear sense input with offset defined by attenuation

Is Nonlinear sense input information valid

Nonlinear Precor state Enumeration: 'initialising-90': 12, 'auto-applying': 13, 'monitoring': 1, 'initialising-40': 7, 'initialising-0': 3, 'initialising-50': 8, 'initialising-60': 9, 'initialising-70': 10, 'initialising': 2, 'initialising-10': 4, 'not-running': 0, 'initialising-20': 5, 'completed': 14, 'initialising-80': 11, 'initialising-30': 6.

PrecorrectorNonlinearUpdateFactoryCurve Enumeration: 'noop': 0, 'update': 1.

Define a adaptive target level for the amplitude ripple

Define a adaptive target level for the group delay

Define a adaptive target level for the lower shoulder

Define a adaptive target level for the upper shoulder

By using this, it is possible to control wether to use the linear Sense Input or not. Enumeration: 'enable': 1, 'disable': 0.

Number of iterations discarded by the linear adaptive precorrector due to noisy signal samples.

By using this, it is possible to control wether to use the nonlinear Sense Input or not. Enumeration: 'enable': 1, 'disable': 0.

Number of iterations discarded by the non-linear adaptive precorrector dur to noisy signal samples.

MER

Is MER information valid

PAPR level

Is Papr information valid

Choose wether or not to use averaging calulations Enumeration: 'yes': 1, 'no': 0.

Enable the modulator's output PAPR limiter function Enumeration: 'enable': 1, 'disable': 0.

Maximum RF PAPR Limitation

Define a target level for the MER

Define a target MER hysteresis

Enable MER as a trigger for the AUTORUN and RUNTOTARGET modes Enumeration: 'on': 1, 'off': 0.

set the built-in peak clipper function. The value 'max' corresponds to an unclipped COFDM signal (12dB peak to average ratio). The value 'min' correspondsto COFDM signal where all peaks >2dB above average power are clipped. When feeding the output from the modulator through an amplifier the best overall performance result is normally obtained if the clipper value used by modulator clips the signal just a fraction before the amplifier would clip the signal.

Set the output peak shaping filter hardness. The value 'min' correspond to traditional 'hard-clipping' where the clipper noise is equally distributed below, inside and above the COFDM spectrum (clipper noise clearly visible in the form of noise above and below the spectrum. The value 'max' corresponds to maximum soft clipping where the clipper noise in the sidebands (above and below the COFDM spectrum) is subjected to maximum suppression while still maintaining the exact clipper value (peak-to-average-ration). The suppression of the sideband noise is obtained as a tradeoff against the in band performance. The clip filter setting is typically selected as a compromise between spectrum shoulder performance and in-band signal performance (MER).

Selection of the operational mode for the adaptive clipper function Enumeration: 'single': 2, 'continuous': 1, 'monitoring': 0.

OptiClipper state Enumeration: 'initialising-90': 12, 'auto-applying': 13, 'monitoring': 1, 'initialising-40': 7, 'initialising-0': 3, 'initialising-50': 8, 'initialising-60': 9, 'initialising-70': 10, 'initialising': 2, 'initialising-10': 4, 'not-running': 0, 'initialising-20': 5, 'completed': 14, 'initialising-80': 11, 'initialising-30': 6.

Lower shoulder level

Is Lower shoulder information valid

Upper shoulder level

Is Upper shoulder information valid

MER level

Is MER information valid

PAPR level

Is Papr information valid

Number of Iterations performed by the OptiClipper algorithm

Selection between no, static (manual) and adaptive clipper function Enumeration: 'monitoring': 0, 'adaptive': 2, 'static': 1.

Clipper shaped by the OptiClipper algorithm

Clipper enable Enumeration: 'on': 1, 'off': 0.

Define a attenuation level for the sense input

Define a attenuation level for the sense input

Linear precorrection curve active in the system

Non-Linear precorrection curve active in the system

Depricated Therefore min and max value are set to 100% Set the peak shaping filter hardness. The value 'min' correspond to traditional 'hard-clipping' where the clipper noise is equally distributed below, inside and above the COFDM spectrum (clipper noise clearly visible in the form of noise above and below the spectrum. The value 'max' corresponds to maximum soft clipping where the clipper noise in the sidebands (above and below the COFDM spectrum) is subjected to maximum suppression while still maintaining the exact clipper value (peak-to-average-ration). The suppression of the sideband noise is obtained as a tradeoff against the in band performance. The clip filter setting is typically selected as a compromise between spectrum shoulder performance and in-band signal performance (MER).

Defines the reception frequency for the tuner.

Defines the offset to be added to the reception frequency for the tuner.

Controls RF/IF reception Policy Enumeration: 'ifav': 3, 'rfav': 2, 'rf': 0, 'if': 1.

Defines the reception frequency for the tuner. Enumeration: 'if36p15mhz': 1, 'if40mhz': 2, 'if36mhz': 0.

Controls IF reception Polarity Enumeration: 'inv': 1, 'norm': 0.

Controls the squelch function. Enumeration: 'on': 1, 'off': 0.

Defines the Squelch function threshold.

Defines the Squelch function Hysteresis.

Controls the gain function mode. Enumeration: 'auto': 0, 'manual': 2, 'freeze': 1.

Defines manual gain value.

Controls the Reception RF Gain limit function. Enumeration: 'on': 1, 'off': 0.

Defines gain limit value.

The current total gain.