IANA-MAU-MIB: View SNMP OID List / Download MIB

no internal MAU, view from AUI

thick coax MAU

FOIRL MAU

thin coax MAU

UTP MAU. Note that it is strongly recommended that agents return either dot3MauType10BaseTHD or dot3MauType10BaseTFD if the duplex mode is known. However, management applications should be prepared to receive this MAU type value from older agent implementations.

passive fiber MAU

sync fiber MAU

async fiber MAU. Note that it is strongly recommended that agents return either dot3MauType10BaseFLHD or dot3MauType10BaseFLFD if the duplex mode is known. However, management applications should be prepared to receive this MAU type value from older agent implementations.

broadband DTE MAU. Note that 10BROAD36 MAUs can be attached to interfaces but not to repeaters.

UTP MAU, half duplex mode

UTP MAU, full duplex mode

async fiber MAU, half duplex mode

async fiber MAU, full duplex mode

4 pair category 3 UTP

2 pair category 5 UTP, half duplex mode

2 pair category 5 UTP, full duplex mode

X fiber over PMT, half duplex mode

X fiber over PMT, full duplex mode

2 pair category 3 UTP, half duplex mode

2 pair category 3 UTP, full duplex mode

PCS/PMA, unknown PMD, half duplex mode

PCS/PMA, unknown PMD, full duplex mode

Fiber over long-wavelength laser, half duplex mode

Fiber over long-wavelength laser, full duplex mode

Fiber over short-wavelength laser, half duplex mode

Fiber over short-wavelength laser, full duplex mode

Copper over 150-Ohm balanced cable, half duplex mode

Copper over 150-Ohm balanced cable, full duplex mode

Four-pair Category 5 UTP, half duplex mode

Four-pair Category 5 UTP, full duplex mode

X PCS/PMA, unknown PMD.

X fiber over WWDM optics

R PCS/PMA, unknown PMD.

R fiber over 1550 nm optics

R fiber over 1310 nm optics

R fiber over 850 nm optics

W PCS/PMA, unknown PMD.

W fiber over 1550 nm optics

W fiber over 1310 nm optics

W fiber over 850 nm optics

X copper over 8 pair 100-Ohm balanced cable

Voice grade UTP copper, up to 2700m, optional PAF

Voice grade UTP copper, up to 750m, optional PAF

One single-mode fiber OLT, long wavelength, 10km

One single-mode fiber ONU, long wavelength, 10km

Two single-mode fibers, long wavelength, 10km

One single-mode fiber OLT, long wavelength, 10km

One single-mode fiber ONU, long wavelength, 10km

Two sigle-mode fiber, long wavelength, 10km

One single-mode fiber EPON OLT, 10km

One single-mode fiber EPON ONU, 10km

One single-mode fiber EPON OLT, 20km

One single-mode fiber EPON ONU, 20km

Four-pair Category 6A or better, full duplex mode only

R multimode fiber over 1310 nm optics

X backplane, full duplex mode only

4 lane X backplane, full duplex mode only

R backplane, full duplex mode only

One single-mode fiber asymmetric-rate EPON OLT, supporting low power budget (PRX10)

One single-mode fiber asymmetric-rate EPON OLT, supporting medium power budget (PRX20)

One single-mode fiber asymmetric-rate EPON OLT, supporting high power budget (PRX30)

One single-mode fiber asymmetric-rate EPON ONU, supporting low power budget (PRX10)

One single-mode fiber asymmetric-rate EPON ONU, supporting medium power budget (PRX20)

One single-mode fiber asymmetric-rate EPON ONU, supporting high power budget (PRX30)

One single-mode fiber symmetric-rate EPON OLT, supporting low power budget (PR10)

One single-mode fiber symmetric-rate EPON OLT, supporting medium power budget (PR20)

One single-mode fiber symmetric-rate EPON OLT, supporting high power budget (PR30)

One single-mode fiber symmetric-rate EPON ONU, supporting low and medium power budget (PR10 and PR20)

One single-mode fiber symmetric-rate EPON ONU, supporting high power budget (PR30)

40GBASE-R PCS/PMA over an electrical backplane

40GBASE-R PCS/PMA over 4 lane shielded copper balanced cable

40GBASE-R PCS/PMA over 4 lane multimode fiber

40GBASE-R PCS/PMA over single mode fiber

40GBASE-R PCS/PMA over 4 WDM lane single mode fiber

100GBASE-R PCS/PMA over 10 lane shielded copper balanced cable

100GBASE-R PCS/PMA over 10 lane multimode fiber

100GBASE-R PCS/PMA over 4 WDM lane single mode fiber, long reach

100GBASE-R PCS/PMA over 4 WDM lane single mode fiber PMD, extended reach

This MIB module defines dot3MauType OBJECT-IDENTITIES and IANAifMauListBits, IANAifMauMediaAvailable, IANAifMauAutoNegCapBits, and IANAifJackType TEXTUAL-CONVENTIONs, specifying enumerated values of the ifMauTypeListBits, ifMauMediaAvailable / rpMauMediaAvailable, ifMauAutoNegCapabilityBits / ifMauAutoNegCapAdvertisedBits / ifMauAutoNegCapReceivedBits and ifJackType / rpJackType objects respectively, defined in the MAU-MIB. It is intended that each new MAU type, Media Availability state, Auto Negotiation capability and/or Jack type defined by the IEEE 802.3 working group and approved for publication in a revision of IEEE Std 802.3 will be added to this MIB module, provided that it is suitable for being managed by the base objects in the MAU-MIB. An Expert Review, as defined in RFC 2434 [RFC2434], is REQUIRED for such additions. The following reference is used throughout this MIB module: [IEEE802.3] refers to: IEEE Std 802.3, 2005 Edition: 'IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications'. This reference should be updated as appropriate when new MAU types, Media Availability states, Auto Negotiation capabilities, and/or Jack types are added to this MIB module. Copyright (C) The IETF Trust (2007). The initial version of this MIB module was published in RFC 4836; for full legal notices see the RFC itself. Supplementary information may be available at: http://www.ietf.org/copyrights/ianamib.html