Fore-Sonet-Ext-MIB: View SNMP OID List / Download MIB

This mib implements extensions to the standard SONET mib to support extra configuration and statistics that are supported by Fore Systems.

This trap indicates that the specified SONET port is experiencing Loss Of Signal. Bellcore Document TA-NWT-000253 Section 6.3.1.1.1 states that... A SONET NE shall declare a LOS failure when the LOS defect persists for 2.5 (+- .5) seconds, or when a LOS defect is present and the criteria for LOF failure declaration have been met.

This trap indicates that the LOS condition identified by trap foreSonetLOSDetected has been cleared.

This trap indicates that the specified SONET port is receiving and errored C2 Path Label byte. Reference Bellcore Document TA-NWT-000253 Section 3.3.2.3 and 6.3.1.1.8 the Path Label (C2) byte should have the value 0x13 or 0x01.

This trap indicates that the Errored Path Label (C2) byte error condition signaled by the foreSonetPathLabelDetected trap has been cleared.

This trap indicates that the specified SONET port is receiving a Line level Alarm Indication Signal from the far-end equipment.

This trap indicates that the Line AIS error condition signaled by the foreSonetLineAISDetected trap has been cleared.

This trap indicates that the specified SONET port is experiencing Loss Of Frame (LOF) failure. An LOF failure is declared when the LOF defect persists fore a period of 2.5 +/- 0.5 seconds, except when an LOS defect or failure is present.

This trap indicates that the LOF failure identified by trap foreSonetLOFDetected has been cleared. The LOF failure is cleared when the LOS failure is declared, or when the LOF defect is absent for 10 +/- 0.5 seconds.

This trap indicates that the specified SONET port is experiencing Line Remote Defect Indication (LRDI). A Line RDI failure is declared when the incoming Line RDI defects lasts for 2.5 +/- 0.5 seconds.

This trap indicates that the Line RDI failure identified by trap foreSonetLineRDIDetected has been cleared. The Line RDI failure is cleared when no Line RDI defects are detected for 10 +/- 0.5 seconds.

This trap indicates that the specified SONET port is experiencing Path Alarm Inidication Signal (PAIS). A Path AIS failure is declared when the Path AIS defect persists for 2.5 +/- 0.5 seconds.

This trap indicates that the PathAIS failure identified by trap foreSonetPathAISDetected has been cleared. A PAIS failure is cleared when the PAIS defect is absent for 10 +/- 0.5 seconds.

This trap indicates that the specified SONET port is experiencing Loss Of Pointer (LOP). A LOP failure is declared when the LOP defect persists for a period of 2.5 +/- 0.5 seconds.

This trap indicates that the LOP failure identified by trap foreSonetLOPDetected has been cleared. A LOP failure is cleared when the LOP defect is absent for 10 +/- 0.5 seconds.

This trap indicates that the specified SONET port is experiencing unequiped (UNEQ). A UNEQ failure is declared when the UNEQ defect persists for a period of 2.5 +/- 0.5 seconds.

This trap indicates that the UNEQ failure identified by trap foreSonetUNEQDetected has been cleared. A UNEQ failure is cleared when the UNEQ defect is absent for 10 +/- 0.5 seconds.

This trap indicates that the specified SONET port is experiencing Path Remote Defect Indication (PRDI). A Path RDI failure is declared when the incoming Path RDI defects lasts for 2.5 +/- 0.5 seconds.

This trap indicates that the Path RDI failure identified by trap foreSonetPathRDIDetected has been cleared. The Path RDI failure is cleared when no Path RDI defects are detected for 10 +/- 0.5 seconds.

This trap indicates that the specified SONET path is experiencing a PDI-P ( Path Defect Indication) condition. A PDI-P indication is signalled by a value in the C2 ( path label ) byte in the range 0xe0..0xfc.

This trap indicates that the PDI falure identified by trap foreSonetPathPDIDetected has been cleared.

This trap indicates that the specified SONET port is experiencing Bit Interleaved Parity (BIP) errors. A Line BIP failure is declared when the Line BIP defect persists for a period of 2.5 +/- 0.5 seconds.

This trap indicates that the Line BIP failure identified by trap asxSonetAtmLineBIPDetected has been cleared. A Line BIP failure is cleared when the Line BIP defect is absent for 10 +/- 0.5 seconds.

This trap indicates that the specified Sonet virtual tributary is receiving an AIS indication from the far end. An AIS-V failure is declared when the AIS-V defect persists for 2.5 +/- 0.5 seconds.

This trap indicates that the virtual tributary AIS failure condition has been cleared. An AIS-V failure is cleared when the AIS-V defect is absent for 10 +/- 0.5 seconds.

This trap indicates that the specified virtual tributary is receiving an LOP-V failure. An LOP-V failure is declared when an LOP-V defect persists for 2.5 +/- 0.5 seconds.

This trap indicates that the specified virtual tributary is no longer experiencing loss-of-pointer failure. An LOP-V failure is cleared when the LOP-V defect is absent for 10 +/- 0.5 seconds

This trap indicates that the specified virtual tributary is receiving an UNEQ virtual tributary. (V5 byte is 0 ).

This trap indicates that the specified virtual tributary is no longer receving an UNEQ virtual tributary.

This trap indicates that the specified virtual tributary is experiencing a VT path label mismatch failure, PLM-V.

This trap indicates that the specified virtual tributary is no longer experiencing a PLM-V failure.

This trap indicates that the specified virtual tributary is experiencing an RDI failure. An RDI-V failure is declared after the interface receives RDI-V defects for 2.5 +/- 0.5 seconds.

This trap indicates that the specified virtual tributary is no longer experiencing an RDI failure. An RDI-V failure is cleared after the interface receives no RDI-V defects for 10 +/- 0.5 seconds.

This trap indicates that the specified virtual tributary is experiencing an RFI-V failure. An RFI-V failure is declared within 5 milliseconds of the detection of an incoming RFI-V indication.

This trap indicates that the specified virtual tributary is no longer experiencing an RFI-V failure. An RFI-V failure is cleared within 50 milliseconds of the removal of an incoming RFI-V indication.

A table of configuration options and statistics that extend the Sonet Medium Group in the Standard SONET MIB.

A table entry containing Fore specific extensions to the standard SONET Medium Group Tables.

This variable represents the current loopback status of the SONET interface. The possible values are: sonetNoLoop (1) means that the interface is not in a loopback state. sonetLineLoop (2) means that the receive data and clock are connected to the transmit data and clock. sonetDiagLoop (3) means that the transmit data stream and clock are looped back to the receiver. sonetOtherLoop (4) means that the interface is in a loopback that is not defined here. Enumeration: 'sonetDiagLoop': 3, 'sonetLineLoop': 2, 'sonetNoLoop': 1, 'sonetOtherLoop': 4.

The source of the transmit clock. Enumeration: 'localTiming': 2, 'rxTiming': 1.

A table of configuration options and statistics that extend the standard Sonet section tables.

A table entry containing Fore specific extensions to the standard SONET section table statistics.

The number of Section BIP-8 (Bit Interleaved Parity) errors that have been detected since the last time the port has been reset. The calculated BIP-8 code is compared with the BIP-8 code extracted from the B1 byte of the following frame. Differences indicate that a section level bit error has occurred.

The number of seconds in which Loss Of Signal (LOS) has occurred. A LOS is declared when 20 +/- 3us of all zeros patterns is detected. LOS is cleared when two valid framing words are detected and during the intervening time no LOS condition is detected.

The number of seconds in which Loss Of Frame (LOF) has occurred. A LOF is declared when an out-of-frame (OOF) condition persists for 3ms. The LOF is cleared when an in-frame condition persists for 3ms. While in-frame the framing bytes (A1, A2) in each frame are compared against the expected pattern. Out-of-frame is declared when four consecutive frames containing one or more framing pattern errors have been received.

A table of configuration options and statistics that extend the standard Sonet Section tables.

A table entry containing Fore specific extensions to the standard SONET Section tables.

Controls the insertion of framing (A1 A2 byte) errors. off When set to off, transmit Sonet frames continously with no A1A2 errors (framing errors). on When set to on, transmit Sonet frames continously with bad A1A2 values. momentary When set to momentary, transmit a chip dependent number of Sonet frames with A1A2 errors. Enumeration: 'on': 1, 'off': 2, 'momentary': 3.

Controls the insertion of BIP errors in the sonet section B1 byte overhead. off When set to off, do not generate section BIP errors. on When set to on, generate section BIP errors. momentary When set to momentary, transmit a chip dependent number of Sonet frames with section BIP errors. Enumeration: 'on': 1, 'off': 2, 'momentary': 3.

Controls the scrambling of sonet overhead and SPE of the transmitted Sonet frame. off When set to off, transmitted Sonet frames are scrambled. on When set to on, transmitted Sonet frames are NOT scrambled. Enumeration: 'on': 1, 'off': 2.

Controls the descrambling of sonet overhead and SPE of the received Sonet frame. off When set to off, received Sonet frames are descrambled. on When set to on, received Sonet frames are NOT descrambled. Enumeration: 'on': 1, 'off': 2.

Controls the insertion of Loss of Signal (LOS) errors in the transmitted Sonet frame. off When set to off, do not generate LOS errors. on When set to on, generate LOS errors. Enumeration: 'on': 1, 'off': 2.

The Fore's extension to SONET/SDH Section Current table.

An entry in the SONET/SDH Section Current table.

The counter associated with the number of Background Errors encountered by a SONET/SDH Section in the current 15 minute interval.

The Fore's extension to SONET/SDH Section Interval table.

An entry in the SONET/SDH Section Interval table.

The counter associated with the number of Background Errors encountered by a SONET/SDH Section in a particular 15-minute interval in the past 24 hours.

The ratio of Errored seconds encountered by a SONET/SDH Section to time in a particular 15-minute interval in the past 24 hours.

The ratio of Sev Errored seconds encountered by a SONET/SDH Section to time in a particular 15-minute interval in the past 24 hours.

The ratio of Background blk errors encountered by a SONET/SDH Section to time in a particular 15-minute interval in the past 24 hours.

A table of configuration options and statistics that extend the Sonet Line Group in the Standard SONET MIB.

A table entry containing Fore specific extensions to the standard SONET Line Group Tables.

This variable represents the consecutive number of BAD/GOOD seconds to detect/clear a B2 byte Line Bit Interleaved Parity (BIP) Defect. The range of the values it can take is between 2 and 10 inclusive.

This variable is a threshold for the number of B2 byte Line Bit Interleaved Parity (BIP) Errors per second and is used as a parameter to the Line BIP Defect. If the number of errors exceeds the threshold, the particular second is declared BAD, otherwise it is declared GOOD.

This variable controls whether declaration of a Line BIP Defect forces the port's operState to Down. Enumeration: 'disabled': 2, 'enabled': 1.

This is the exponent of 10 for the current signal degrade bit error rate (BER) threshold for this port. The value -7, for example, represents a BER of 1E-7. This variable is only applicable when sonetLineBerErrorModel is set to errorModelRandom.

This is the exponent of 10 for the current signal fail bit error rate (BER) threshold for this port. The value -4, for example, represents a BER of 1E-4. This variable is only applicable when sonetLineBerErrorModel is set to errorModelRandom.

This is the error distribution model to be used to identify signal degrade and signal fail conditions. errorModelRandom selects a random error distribution and declares signal conditions based on the thresholds set in sonetLineSignalDegradeBer and sonetLineSignalFailBer. errorModelBurst selects a burst error model and declares signal degrade conditions based on the thresholds set in sonetLineBipThrSeconds and sonetLineBipThrErrors. errorModelNone disables detection of signal conditions. Enumeration: 'errorModelNone': 0, 'errorModelBurst': 2, 'errorModelRandom': 1.

This value describes the current state of the port as determined through bit error rate analysis. Enumeration: 'berStateSigFail': 2, 'berStateOk': 0, 'berStateSigDegrade': 1.

A table of configuration options and statistics that extend the Sonet Line Group in the Standard SONET MIB.

A table entry containing Fore specific extensions to the standard SONET Line Group Tables.

The number of Line BIP-24 (Bit Interleaved Parity) errors that have been detected since the last time the port has been reset. The calculated BIP-24 code is based on the line overhead and synchronous payload envelope (SPE) of the STS-3c stream. The line BIP-24 code is a bit interleaved parity calculation using even parity. The calculated code is compared with the BIP-24 code extracted from the B2 bytes of the following frame. Differences indicate that a line layer bit error has occurred.

The number of line Far End Block Errors (FEBE) that have been detected since the last time the port has been reset.

The number of seconds in which line Alarm Indication Signal (AIS) has occurred. A line AIS is asserted when a 111 binary pattern is detected in bits 6,7,8 of the K2 byte for five consecutive frames. A line AIS is removed when any pattern other than 111 is detected in these bits for five consecutive frames.

The number of seconds in which line Far End Receive Failure (RDI) has occurred. A line RDI is asserted when a 110 binary pattern is detected in bits 6,7,8 of the K2 byte for five consecutive frames. A line RDI is removed when any pattern other than 110 is detected in these bits for five consecutive frames.

A table of configuration options and statistics that extend the Sonet Line Group in the Standard SONET MIB.

A table entry containing Fore specific extensions to the standard SONET Line Group Tables.

Controls the insertion of line alarm indication signal (AIS_L). on When set to on, all bits of the SONET frame are set to 1 except for the section overhead. off resume normal operation Enumeration: 'on': 1, 'off': 2.

Controls the insertion of BIP errors in the sonet line B2 byte overhead. off When set to off, do not generate line BIP errors. on When set to on, generate line BIP errors. momentary When set to momentary, transmit a chip dependent number of Sonet frame with line BIP errors. Enumeration: 'on': 1, 'off': 2, 'momentary': 3.

Controls the insertion of line APS bytes (K1 and K2) that are determined by normal operating rules or by diagnostic mibs. off When set to off, resume normal operation. on When set to on, K1 and K2 bytes are calculated by contents of diagnostic mibs. Enumeration: 'on': 1, 'off': 2.

Specifies the channel number code, k1 bits 5 to 8. * null(0) - null channel Code 0 is used with the Lockout of Protection request. * working(1..14) - Working channels Codes 1 through n apply in a 1:n architecture Only code 1 applies in a 1+1 architecture *extraTraffic(15) - Extra traffic channel May exist only when provisioned in a 1:n architecture NOTE: Refer to GR-253-CORE for more details Enumeration: 'working14': 14, 'working13': 13, 'working12': 12, 'working11': 11, 'working10': 10, 'extraTraffic': 15, 'working9': 9, 'working8': 8, 'working3': 3, 'working2': 2, 'working1': 1, 'null': 0, 'working7': 7, 'working6': 6, 'working5': 5, 'working4': 4.

Defines the various values for K1 byte (1-4) for the type of request For 1+1 systems, Forced and Manual switch request apply. SD and SF requests apply to conditions detected on the protection line. Enumeration: 'wtr': 6, 'sdlp': 10, 'rr': 2, 'sflp': 12, 'sdhp': 11, 'noreq': 0, 'sfhp': 13, 'forcedsw': 14, 'lockout': 15, 'manualsw': 8, 'donotrevert': 1, 'exercise': 4.

Specifies the channel number code, k2 bits 1 to 4 * null - null channel Code 0 is used with the Lockout of Protection request. * working(1..14) - Working channels Codes 1 through n apply in a 1:n architecture Only code1 applies in a 1+1 architecture * extraTraffic(15) - Extra traffic channel May exist only when provisioned in a 1:n architecture NOTE: Refer to GR-253-CORE for more details Enumeration: 'working14': 14, 'working13': 13, 'working12': 12, 'working11': 11, 'working10': 10, 'extraTraffic': 15, 'working9': 9, 'working8': 8, 'working3': 3, 'working2': 2, 'working1': 1, 'null': 0, 'working7': 7, 'working6': 6, 'working5': 5, 'working4': 4.

Bit 5 of the K2 byte shall be set to indicate: Code '0' if the provisioned (or only supported) architecture is 1+1 Code '1' if the provisioned (or only supported) architecture is 1:n Enumeration: 'oneplusone': 0, 'onen': 1.

Bits 6 through 8 of the K2 byte shall be set to indicate: Code '101' if the provisioned mode is bidirectional Code '100' if the provisioned mode is unidirectional The codes '011', '010', '001' and '000' in K2 bites 6-8 are reserved for future use in 1:n drop and insert(nested) protection switching, and the code '111' is used in detecting an incoming AIS_L. Enumeration: 'bidirectional': 5, 'unidirectional': 4.

Controls the insertion of line Remote Defect Indication (Line RDI). Line RDI is inserted by transmitting the code 110 (binary) in bit positions 6, 7 and 8 of the K2 byte contained in the transmit stream. off When set to off, Line RDI is NOT inserted in the transmit stream even if LOS/LOF is received on When set to on, Line RDI is inserted continuously in the transmit stream. auto When set to auto, Line RDI is inserted as under normal operation Enumeration: 'on': 1, 'off': 2, 'auto': 4.

Controls the insertion of Line Remote Error Indication (REI_L). The number of BIP errors (B2) detected are encoded in the transmit REI_L (M0/M1) byte. REI_L was previously called Line FEBE (Far End Block Error). off When set to off, insert 0 for M0/M1 bytes, irrespective of the number of B2 errors received. on When set to on, insert 8/8N for M0/M1 bytes continuously. auto When set to auto, resume normal operation. Enumeration: 'on': 1, 'off': 2, 'auto': 4.

The Fore's extension to SONET/SDH Line Current table.

An entry in the SONET/SDH Line Current table.

The counter associated with the number of Background Errors encountered by a SONET/SDH Line in the current 15 minute interval.

The Fore's extension to SONET/SDH Line Interval table.

An entry in the SONET/SDH Line Interval table.

The counter associated with the number of Background Errors encountered by a SONET/SDH Line in a particular 15-minute interval in the past 24 hours.

The ratio of Errored seconds encountered by a SONET/SDH Line to time in a particular 15-minute interval in the past 24 hours.

The ratio of Sev Errored seconds encountered by a SONET/SDH Line to time in a particular 15-minute interval in the past 24 hours.

The ratio of Background blk errors encountered by a SONET/SDH Line to time in a particular 15-minute interval in the past 24 hours.

A table of configuration options and statistics that extend the standard SONET Path Tables

A table entry containing Fore specific extensions to the standard SONET path tables

This variable contains the path signal label byte (C2). The value in this variable is updated to a new path signal label value if the same new value is observed for two consecutive frames.

This variable controls the transmit path payload. The default value for ATM is 0x13 (19 decimal). Changing the value of this variable attempts to change the payload and if successfull will change the transmitted C2 label to reflect the new payload. Use the C2 variable in the diagnostics table if you wish to change the C2 value for diagnostic purposes without actually changing the transmitted payload type.

This variable represents the current loopback status of the SONET interface. The possible values are: sonetPathNoLoop (1) means that the interface is not in a loopback state. sonetPathLineLoop (2) means that the receive data is connected to the transmit data. sonetPathDiagLoop (3) means that the transmit data stream is looped back to the receiver. sonetPathOtherLoop (4) means that the interface is in a loopback that is not defined here. Enumeration: 'sonetPathOtherLoop': 4, 'sonetPathDiagLoop': 3, 'sonetPathNoLoop': 1, 'sonetPathLineLoop': 2.

A table of configuration options and statistics that extend the standard SONET Path Tables

A table entry containing Fore specific extensions to the standard SONET path tables

The number of Path BIP-8 (Bit Interleaved Parity) errors that have been detected since the last time the port has been reset. A path BIP-8 error is detected by comparing the path BIP-8 byte (B3) extracted from the current frame, to the path BIP-8 computed for the previous frame.

The number of seconds in which path Loss Of Pointer (LOP) has occurred. A path LOP is detected when a 'normal pointer value' is not found in eight consecutive frames. The LOP is cleared when a 'normal pointer value' is detected for three consecutive frames.

The number of seconds in which path Alarm Indication Signal (AIS) has occurred. A path AIS is asserted when an all-ones pattern is detected in the pointer bytes (H1 and H2) for three consecutive frames. It is cleared when a valid pointer is detected for three consecutive frames. AIS indicates that an upstream failure has been detected.

The number of seconds in which path RDI alarm has occurred. A path RDI alarm is detected by extracting bit 5 of the path status byte. If bit 5 is high for ten consecutive frames, a RDI alarm is declared. A RDI alarm is cleared when bit 5 is low for ten consecutive frames. RDI signals are used to alert upstream terminals of a downstream failure in order to initiate trunk conditioning on the failure circuit.

The number of seconds in which a path UNEQ defect has occurred. A path UNEQ defect is detected when the STS Signal label (C2 byte) == 0x00

The number of seconds in which a path PLM defect has occrred. A path PLM defect is detected when the STS Signal lable (C2 bytes) != 0x00, 0x01, 0x13, 0xFC or 0xFF.

The number of path Far End Block Errors (FEBE) that have been detected since the last time the port has been reset. FEBEs are detected by extracting the 4-bit FEBE field from the path status byte (G1). The legal range for the 4 bit field is between 0000 and 1000, representing zero to eight errors. Any other value is interpreted as zero errors.

A table of configuration options and statistics that extend the standard SONET Path table.

A table entry containing fore specific extensions to the current status table for SONET paths.

This variable indicates information about the current status of the sonet path. This variable is encoded as a bit vector so it can represent multiple conditions simultaneously. The various bit positions are: 1 pathPDI-P detected pathPDI-P is set when the incoming path C2 byte is set to a value in the range 0xe1..0xfc.

The counter associated with the number of Background Errors encountered by a SONET/SDH Path in the current 15 minute interval.

A table of diagnostics tests that extend the standard SONET Path Tables

A table entry containing Fore specific extensions to the standard SONET path tables

Controls the insertion of Signal label/Payload Defect Indication (PDI_P) into the C2 byte of the Sonet path overhead. The various values for Signal label/PDI_P are defined in GR-253-CORE. off When set to off, the C2 byte is set to previously configured C2 value. on When set to on, the foreSonetPathDiagnosticsC2Value is inserted in the C2 byte of the tranmsit stream. Enumeration: 'on': 1, 'off': 2.

Contains C2 byte value of the transmit stream Enumeration: 'sts1with27vtxPD': 251, 'sts1with15vtxPD': 239, 'sts1with16vtxPD': 240, 'sts1with22vtxPD': 246, 'sts1with11vtxPD': 235, 'sts1with26vtxPD': 250, 'sts1with12vtxPD': 236, 'sts1with10vtxPD': 234, 'equippednonspecPL': 1, 'sts1with4vtxPD': 228, 'sts1with25vtxPD': 249, 'sts1with19vtxPD': 243, 'sts1with7vtxPD': 231, 'lockedVTmode': 3, 'sts1with20vtxPD': 244, 'asyncfddimapping': 21, 'sts1with24vtxPD': 248, 'unequipped': 0, 'sts1with13vtxPD': 237, 'payloaddefect': 252, 'hdlcwithscrambling': 22, 'sts1with14vtxPD': 238, 'sts1with3vtxPD': 227, 'atmmapping': 19, 'sts1with21vtxPD': 245, 'sts1with17vtxPD': 241, 'sts1with18vtxPD': 242, 'asyncDS4na': 18, 'sts1with1vtxPD': 225, 'sts1with5vtxPD': 229, 'vtstructSTSSPE': 2, 'sts1with9vtxPD': 233, 'sts1with23vtxPD': 247, 'sts1with2vtxPD': 226, 'dqdbmapping': 20, 'sts1with6vtxPD': 230, 'sts1with8vtxPD': 232, 'asyncDS3mapping': 4.

Controls the insertion of Path BIP errors in the sonet path B3 byte overhead. off When set to off, do not generate path BIP errors. on When set to on, generate path BIP errors. momentary When set to momentary, transmit a chip dependent number of Sonet frames with path BIP errors. Enumeration: 'on': 1, 'off': 2, 'momentary': 3.

Controls the insertion of Sonet Path Remote Error Indication (REI_P) (previously called Far End Block Error (FEBE)). G1 byte 1 2 3 4 5 6 7 8 ----|----|----|----|----|----|----|----| | REI_P | RDI_P | uu | ---------------------------------------- REI_P Path Remote Error Indication RDI_P Path Remote Defect Indication uu Unused off When set to off, the value 0 is inserted in bits 1:4 of G1 byte. on When set to on, the value 0x8 is inserted in bits 1:4 of G1 byte. auto When set to auto, resume normal operation. Enumeration: 'on': 1, 'off': 2, 'auto': 4.

Controls the insertion of STS Path Alarm Indication Signal (AIS_P). off When set to off, AIS_P is not generated under any circumstances. on When set to on, AIS_P is generated. Enumeration: 'on': 1, 'off': 2.

Controls the insertion of Enhanced Remote Defect Indication. Bits 5,6, and 7 of G1 byte is used for the inserting ERDI. G1 byte 1 2 3 4 5 6 7 8 ----|----|----|----|----|----|----|----| | REI_P | RDI_P | uu | ---------------------------------------- REI_P Path Remote Error Indication RDI_P Path Remote Defect Indication uu Unused on When set to on, foreSonetPathDiagnosticsERDIValue is inserted in the bits 5,6,7 of G1 byte. auto When set to auto, resume normal operation using single bit RDI. Enumeration: 'on': 1, 'auto': 4.

Defines the values that may be inserted in the bits 5,6 and 7 of G1 byte. 1xx - One bit RDI 000 - No RDI_P defect with no priority 001 - No RDI_P defect 010 - ERDI_P payload defect 101 - ERDI_P server defect 110 - ERDI_P connectivity defect Enumeration: 'sonetPathERDIconnDefect': 6, 'sonetPathERDInoDefect': 1, 'sonetPathERDIserverDefect': 5, 'sonetPathERDInoPrionoDefect': 0, 'sonetPathERDIpayloadDefect': 2, 'sonetPathERDIOnebitRDI': 4.

Controls the insertion of Loss of pointer for path level. off When set to off, loss of pointer is not generated. on When set to on, loss of pointer is generated in the transmit direction. Enumeration: 'on': 1, 'off': 2.

A table of configuration options for Sonet Path VT Groups that extend the standard SONET Path tables.

A table entry containing Marconi specific extensions to the SONET Path configuration table.

This variable indicates the sonet VT group number within the sonet path. It can range from 0 to 6.

This variable indicates the sonet VT width. Enumeration: 'vtWidth6c': 5, 'vtWidth6VC2': 4, 'vtWidth15VC11': 1, 'vtWidth2VC12': 2, 'vtWidth3': 3.

The Fore's extension to SONET/SDH Path Interval table.

An entry in the SONET/SDH Path Interval table.

The counter associated with the number of Background Errors encountered by a SONET/SDH Path in a particular 15-minute interval in the past 24 hours.

The ratio of Errored seconds encountered by a SONET/SDH Path to time in a particular 15-minute interval in the past 24 hours.

The ratio of Sev Errored seconds encountered by a SONET/SDH Path to time in a particular 15-minute interval in the past 24 hours.

The ratio of Background blk errors encountered by a SONET/SDH Path to time in a particular 15-minute interval in the past 24 hours.

A table of sonet VT configuration options that extend the standard sonet VT tables

A table entry containing Fore specific extensions to the standard sonet VT tables

This variable represents the current loopback status of the sonet interface. The possible values are: sonetVTNoLoop(1): interface is not in a loopback state. sonetVTLineLoop(2): data on the receive path is looped back on to the transmit path. sonetVTDiagLoop(3): data to be transmitted on the transmit path is looped back on to the receive path. sonetVTOtherLoop(4): the loopback mode is not defined here. Enumeration: 'sonetVTDiagLoop': 3, 'sonetVTOtherLoop': 4, 'sonetVTNoLoop': 1, 'sonetVTLineLoop': 2.

A table of statistics that extend the standard sonet VT Tables

A table entry containing Fore specific extensions to the standard sonet VT tables

The number of VT BIP-2 errors that have been detected since the last time this interface has been reset.

The number of REIs that have been detected since the last time this interface has been reset.

The number of seconds in which VT LOP has occurred since the last time this interface has been reset.

The number of seconds in which VT AIS has occurred since the last time this interface has been reset.

The number of seconds in which VT RDI has occurred since the last time this interface has been reset.

The number of seconds in which VT UNEQ has occurred since the last time this interface has been reset.

The number of seconds in which VT PLM has occrred since the last time this interface has been reset.

A table of diagnostic controls that are used to manipulate Sonet virtual tributaries.

A table entry containing Marconi specific extensions to the standard Sonet VT Tables.

Controls the insertion of VT BIP errors in the sonet VT V5 byte overhead. on: Generate sonet VT BIP errors continuously. off: Do not generate sonet VT BIP errors. momentary: Generate a chip dependent number of sonet frames with sonet VT BIP errors. Enumeration: 'on': 1, 'off': 2, 'momentary': 3.

Controls the generation of VT RDI defects on the selected interface. Value Description on(1) RDI is continually tramsmitted off(2) RDI is never transmitted momentary(3) RDI is transmitted for a short period of time. auto(4) RDI is generated according to the sonet specification Enumeration: 'on': 1, 'off': 2, 'auto': 4, 'momentary': 3.

Controls the generation of VT RFI defects on the selected interface. Value Description on(1) RFI is continually tramsmitted off(2) RFI is never transmitted momentary(3) RFI is transmitted for a short period of time. auto(4) RFI is generated according to the sonet specification Enumeration: 'on': 1, 'off': 2, 'auto': 4, 'momentary': 3.

Controls the generation of VT AIS on the selected interface. Value Description on(1) AIS is continually tramsmitted off(2) AIS is never transmitted momentary(3) AIS is transmitted for a short period of time. auto(4) AIS is generated according to the sonet specification Enumeration: 'on': 1, 'off': 2, 'auto': 4, 'momentary': 3.

Controls the generation of VT LOP on the selected interface. Value Description on(1) LOP is continually tramsmitted off(2) LOP is never transmitted momentary(3) LOP is transmitted for a short period of time. Enumeration: 'on': 1, 'off': 2, 'momentary': 3.

Controls the transmission of generated label values to force PLM-V failures on the remote system. Value Description on(1) Use label value in foreSonetVtDiagnosticsLableValue off(2) Transmit label appropriate for VT type Enumeration: 'on': 1, 'off': 2.

Selects the label value to be transmitted in order to force PLM-V failures on the remote system. Enumeration: 'unequipped': 0, 'equippednonspec': 1, 'asynchronous': 2, 'bytesynchronous': 4, 'bitsynchronous': 3.

Controls the generation of VT REI on the selected interface. REI indicates to the far end that a BIP-2 error check failed. Value Description on(1) REI is continually tramsmitted off(2) REI is never transmitted auto(4) REI is transmitted according to the BIP-2 Enumeration: 'on': 1, 'off': 2, 'auto': 4.

The Fore's extension to SONET/SDH VT Current table.

An entry in the SONET/SDH VT Current table.

The counter associated with the number of Background Errors encountered by a SONET/SDH VT in the current 15 minute interval.

The Fore's extension to SONET/SDH VT Interval table.

An entry in the SONET/SDH VT Interval table.

The counter associated with the number of Background Errors encountered by a SONET/SDH VT in a particular 15-minute interval in the past 24 hours.

The ratio of Errored seconds encountered by a SONET/SDH Section to time in a particular 15-minute interval in the past 24 hours.

The ratio of Sev Errored seconds encountered by a SONET/SDH Section to time in a particular 15-minute interval in the past 24 hours.

The ratio of Background blk errors encountered by a SONET/SDH Section to time in a particular 15-minute interval in the past 24 hours.

The Fore's extension to SONET/SDH Farend Line Current table.

An entry in the SONET/SDH FarEnd Line Current table.

The counter associated with the number of Background Errors encountered by a SONET/SDH FarEnd Line in the current 15 minute interval.

The Fore's extension to SONET/SDH FarEndLine Interval table.

An entry in the SONET/SDH FarEndLine Interval table.

The counter associated with the number of Background Errors encountered by a SONET/SDH FarEndLine in a particular 15-minute interval in the past 24 hours.

The ratio of Errored seconds encountered by a SONET/SDH FarEndLine to time in a particular 15-minute interval in the past 24 hours.

The ratio of Sev Errored seconds encountered by a SONET/SDH FarEndLine to time in a particular 15-minute interval in the past 24 hours.

The ratio of Background blk errors encountered by a SONET/SDH FarEndLine to time in a particular 15-minute interval in the past 24 hours.

The Fore's extension to SONET/SDH FarEnd Path Current table.

An entry in the SONET/SDH FarEnd Path Current table.

The counter associated with the number of Background Errors encountered by a SONET/SDH FarEnd Path in the current 15 minute interval.

The Fore's extension to SONET/SDH FarEndPath Interval table.

An entry in the SONET/SDH FarEndPath Interval table.

The counter associated with the number of Background Errors encountered by a SONET/SDH FarEndPath in a particular 15-minute interval in the past 24 hours.

The ratio of Errored seconds encountered by a SONET/SDH FarEndPath to time in a particular 15-minute interval in the past 24 hours.

The ratio of Sev Errored seconds encountered by a SONET/SDH FarEndPath to time in a particular 15-minute interval in the past 24 hours.

The ratio of Background blk errors encountered by a SONET/SDH FarEndPath to time in a particular 15-minute interval in the past 24 hours.

The Fore's extension to SONET/SDH Farend VT Current table.

An entry in the SONET/SDH FarEnd VT Current table.

The counter associated with the number of Background Errors encountered by a SONET/SDH FarEnd VT in the current 15 minute interval.

The Fore's extension to SONET/SDH FarEndVT Interval table.

An entry in the SONET/SDH FarEndVT Interval table.

The counter associated with the number of Background Errors encountered by a SONET/SDH FarEndVT in a particular 15-minute interval in the past 24 hours.

The ratio of Errored seconds encountered by a SONET/SDH FarEndVT to time in a particular 15-minute interval in the past 24 hours.

The ratio of Sev Errored seconds encountered by a SONET/SDH FarEndVT to time in a particular 15-minute interval in the past 24 hours.

The ratio of Background blk errors encountered by a SONET/SDH FarEndVT to time in a particular 15-minute interval in the past 24 hours.