FASTPATH-SWITCHING-MIB: View SNMP OID List / Download MIB

The Broadcom Private MIB for FastPath Switching

This trap is sent when more than one user is logged in with administrative access. Only applies to CLI interface.

This trap is sent when a broadcast storm is detected.

This trap is sent when a broadcast storm is no longer detected.

Trap is sent when attempting to delete the last configured VLAN or the Default VLAN.

Trap is sent if there are failures in resetting VLAN configuration to defaults.

Trap is sent when this machine is a new STP Root when there is more than one STP instance.

Trap is sent when there is a STP topology change when there is more than one STP instance.

Trap is sent when a user fails to authenticate via the CLI or Web interfaces.

Trap is sent when a user account is locked due to consecutive failed login attempts via the CLI or Web interfaces beyond the allowed limit.

Trap is sent once an interface is error disabled by DAI when the incoming packet rate exceeded configured rate limit during a burst-interval.

Trap is sent when this port in this STP instance enters loop inconsistent state upon failure to receive a BPDU.

Trap is sent when this port in this STP instance exits loop inconsistent state upon reception of a BPDU.

Trap is sent once an interface is error disabled by DHCP Snooping when the incoming packet rate exceeded configured rate limit during a burst-interval.

The switch's Inventory system description.

Type of the Machine used in the Switch

The switch's Machine Model.

Serial number of the switch.

FRU Number of the switch

The switch's Inventory Maintenance Level

The switch's Inventory Part Number

Name of the Manufacturer of this unit

Burned-In MAC Address

Operating System running on this unit

Network Processing Device for this unit

Lists additional functional packages available on this unit.

Lists the version of software loaded on this unit.

The total number of traps sent since last reset.

The number of traps sent since last viewed.

Agent Trap Log

Agent trap log entry

Unique index of trap entry

System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.

Description of the trap sent.

Supported MIB table

Supported MIB entry

Unique index of the Supported MIB entry

The name of the MIB (RFC or IEEE) that is supported.

Description of the MIB (RFC or IEEE) that is supported.

The total memory free for utilization.

The total memory available.

A table of Task and cpu utilization.

Represents entry for a Task Table.

Unique index of process table

Name of the process

Percentage of CPU Utilized by corresponding task

Process ID

Total CPU Utilization over a period of 5 seconds, 1 minute, and 5 minutes

A table of the switch's login session

Login Session Entry

Agent Login Session Index of the switch

Agent Login Session UserName of the switch

Agent Login Session IP Address of the switch

Agent Login Session Connection Type of the switch Enumeration: 'serial': 1, 'https': 5, 'http': 4, 'ssh': 3, 'telnet': 2.

Agent Login Session Idle Time of the switch

Agent Login Session Time of the switch

Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.

Type of address agentLoginSessionInetAddress is returning. Can be either unknown(0), ipv4(1), or ipv6 (2). Will return unknown(0) in the case of a serial login.

Inet Address of the connecting the user is logging in with. Will return a zero-length string in the case of a serial login.

Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 0 to 65535. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration.

Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 4 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established.

Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it. Enumeration: 'enable': 1, 'disable': 2.

Get/Set the port no which should be used to open telnet sessions on switch. Port No is an integer value from 1 to 65535 and the given port should not be in use by any other service. The default value is 23.

Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is limited to alpha-numeric strings (uncluding the '-' and '_' characters).

User Config Table

User Config Entry

Agent User Config Index

Agent User Name. This string is limited to alpha-numeric strings (including the '-' and '_' characters).

Agent User Password This object will return an empty string even if a password is set.

Agent User Access Mode Enumeration: 'read': 1, 'write': 2.

Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.

Displays whether the user account is locked due to excessive failed login attempts. Enumeration: 'true': 1, 'false': 0.

Date and time when the user's password expires (past or present). Only valid when password aging is enabled.

agentSerialTimeout specifies the maximum connect time(in minutes) without console activity. A value of 0 indicates that a console can be connected indefinitely. The time range is 0 to 65535.

agentSerialBaudrate specifies the current baud rate at which the serial port will try to connect. The available values are 1200, 2400, 4800, 9600, 19200, 38400,57600, and 115200 baud. Enumeration: 'baud-38400': 6, 'baud-115200': 8, 'baud-4800': 3, 'baud-1200': 1, 'baud-9600': 4, 'baud-2400': 2, 'baud-57600': 7, 'baud-19200': 5.

agentSerialCharacterSize specifies the number of bits in a character. The number of bits is always 8.

agentSerialHardwareFlowControl specifies whether hardware flow-control is enabled or disabled. Hardware Flow Control is always disabled. Enumeration: 'enable': 1, 'disable': 2.

agentSerialStopBits specifies the number of Stop bits per character. The number of Stop bits is always 1.

agentSerialParityType specifies the Parity Method used on the Serial Port. The Parity Method is always None. Enumeration: 'even': 1, 'none': 3, 'odd': 2.

Minimum length for user passwords All new local user passwords must be at least this many characters in length.

The number of previous passwords to store for prevention of password reuse. This ensures that each user does not reuse passwords often. A value of 0 indicates that no previous passwords will be stored.

The maximum time that user passwords are valid, in days, from the time the password is set. Once a password expires, the user will be required to enter a new password following the first login after password expiration. A value of 0 indicates that passwords never expire.

The number of allowable failed local authentication attempts before the user's account is locked. A value of 0 indicates that user accounts will never be locked.

Agent LAG Create. When this object is set with a non-empty string, a new LAG will be created if possible with the entered string as its name.

A summary table of the switch's LAG config entries

Switch's LAG config entry

Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable.

Agent LAG Name. The associated name of the LAG used during creation.

Agent LAG FlushTimer.

Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down. Enumeration: 'enable': 1, 'disable': 2.

Agent LAG AdminMode. Administratively enables or disables this LAG interface. Enumeration: 'enable': 1, 'disable': 2.

Agent LAG StpMode If Dot1d is enabled, the valid values are: dot1d(1), fast(2), and off(3) If Dot1s is enabled, the valid values are: off(3) and dot1s(4) Enumeration: 'dot1s': 4, 'dot1d': 1, 'off': 3, 'fast': 2.

Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: agentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any.

Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable.

Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG.

Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained. Enumeration: 'dynamic': 2, 'static': 1.

Agent LAG Static Capability enable(1) - Static capability is enabled for this LAG interface disable(2) - Static capability is disabled for this LAG interface Enumeration: 'enable': 1, 'disable': 2.

Agent LAG Hash Mode. This configures the hashing-mode for trunk port computation. The following are the possible values for hashing-mode. 1 - Source MAC, VLAN, EtherType, SourceModule and Port Id. 2 - Destination MAC, VLAN, EtherType, SourceModule and Port Id. 3 - Source IP and Source TCP/UDP Port. 4 - Destination IP and Destination TCP/UDP Port. 5 - Source/Destination MAC, VLAN, EtherType, source MODID/port. 6 - Source/Destination IP and source/destination TCP/UDP Port.

Enumeration: 'access': 1, 'general': 3, 'trunk': 2.

Describes and Configures the VLAN ID of access switch port. A value of 0 indicates that the switch port is not configured as access port.

A detailed table of the switch's LAG config entries

Switch's LAG config entry

LAG index

LAG port index

LAG port speed. See agentPortType for a description and list of valid values.

LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG. Enumeration: 'active': 1, 'inactive': 2.

Agent LAG Static Capability. Configures whether Static LAGs are supported on this device. Enumeration: 'enable': 1, 'disable': 2.

The switch's network ip address

The switch's network subnet mask

The switch's network default gateway

The switch's network Burned-In MAC address

The switch's network locally administered MAC address

The switch's network Mac Address Type Enumeration: 'burned-in': 1, 'local': 2.

The switch's network config protocol Enumeration: 'dhcp': 3, 'none': 1, 'bootp': 2.

The switch's network config protocol on next bootup This object has been obsoleted by agentHTTPWebMode. Enumeration: 'enable': 1, 'disable': 2.

Configures the use of the Java interface through the Web. This object has been obsoleted by agentHTTPJavaMode. Enumeration: 'enable': 1, 'disable': 2.

The VLAN ID through which the switch can be managed using the agentNetworkIPAddress

The network port IPv6 administrative state Enumeration: 'disabled': 2, 'enabled': 1.

The network port IPv6 Gateway Address

The list of IPv6 address prefixes for the network port.

An interface entry containing objects of a particular IPv6 address prefix

The service port IPv6 Address Prefix

The service port IPv6 Address Prefix Length

The service port IPv6 Eui Flag Enumeration: 'disabled': 2, 'enabled': 1.

The ipv6 address autoconfig allows the device to perform IPv6 stateless address auto-configuration to discover prefixes on the link and then to add the eui-64 based addresses to the network interface. Enumeration: 'enable': 1, 'disable': 2.

The switch's network IPv6 config protocol Enumeration: 'dhcp': 2, 'none': 1.

The DHCPv6 Client unique DUID. This value cannot be modified

The no. of DHCPv6 messages of type ADVERTISE that have been received by the DHCPv6 client on the network port.

The no. of DHCPv6 messages of type REPLY that have been received by the DHCPv6 client on the network port.

The no. of DHCPv6 messages of type ADVERTISE that have been discarded by the DHCPv6 client on the network port.

The no. of DHCPv6 messages of type REPLY that have been discarded by the DHCPv6 client on the network port.

The no. of DHCPv6 messages received malformed by the DHCPv6 client on the network port.

The no. of DHCPv6 messages of type SOLICIT that have been sent by the DHCPv6 client on the network port.

The no. of DHCPv6 messages of type REQUEST that have been sent by the DHCPv6 client on the network port.

The no. of DHCPv6 messages of type RENEW that have been sent by the DHCPv6 client on the network port.

The no. of DHCPv6 messages of type REBIND that have been sent by the DHCPv6 client on the network port.

The no. of DHCPv6 messages of type RELEASE that have been sent by the DHCPv6 client on the network port.

Clear the DHCPv6 Client statistics on the network port. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator. Enumeration: 'reset': 1, 'none': 0.

The switch's ServicePort ip address

The switch's ServicePort subnet mask

The switch's ServicePort default gateway

The switch's ServicePort Burned-In MAC address

The switch's ServicePort config protocol Enumeration: 'dhcp': 3, 'none': 1, 'bootp': 2.

The service port IPv6 administrative state Enumeration: 'disabled': 2, 'enabled': 1.

The service port IPv6 Gateway Address

The list of IPv6 address prefixes for the service port.

An interface entry containing objects of a particular IPv6 address prefix

The service port IPv6 Address Prefix

The service port IPv6 Address Prefix Length

The service port IPv6 Eui Flag Enumeration: 'disabled': 2, 'enabled': 1.

The ipv6 address autoconfig allows the device to perform IPv6 stateless address auto-configuration to discover prefixes on the link and then to add the eui-64 based addresses to the serviceport interface. Enumeration: 'enable': 1, 'disable': 2.

The Service Port.s IPv6 protocol configured on the switch. Enumeration: 'dhcp': 2, 'none': 1.

The DHCPv6 Client unique DUID. This value cannot be modified

The no. of DHCPv6 messages of type ADVERTISE that have been received by the DHCPv6 client on the service port.

The no. of DHCPv6 messages of type REPLY that have been received by the DHCPv6 client on the service port.

The no. of DHCPv6 messages of type ADVERTISE that have been discarded by the DHCPv6 client on the service port.

The no. of DHCPv6 messages of type REPLY that have been discarded by the DHCPv6 client on the service port.

The no. of DHCPv6 messages received malformed by the DHCPv6 client on the service port.

The no. of DHCPv6 messages of type SOLICIT that have been sent by the DHCPv6 client on the service port.

The no. of DHCPv6 messages of type REQUEST that have been sent by the DHCPv6 client on the service port.

The no. of DHCPv6 messages of type RENEW that have been sent by the DHCPv6 client on the service port.

The no. of DHCPv6 messages of type REBIND that have been sent by the DHCPv6 client on the service port.

The no. of DHCPv6 messages of type RELEASE that have been sent by the DHCPv6 client on the service port.

Clear the DHCPv6 Client statistics on the service port. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator. Enumeration: 'reset': 1, 'none': 0.

Authentication Flag - Enable/Disable authentication Flag. Enumeration: 'enable': 1, 'disable': 2.

Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable. Enumeration: 'enable': 1, 'disable': 2.

Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session. Enumeration: 'enable': 1, 'disable': 2.

Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps. Enumeration: 'enable': 1, 'disable': 2.

Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the Broadcast Storm Start/End traps are sent when the switch enters and leaves Broadcast Storm Recovery. Enumeration: 'enable': 1, 'disable': 2.

The switch's Spanning Tree Switch Status. This functionality is now handled by agentStpAdminMode Enumeration: 'enable': 1, 'disable': 2.

The spanning tree BPDU Guard Mode. enable(1) - enables BPDU Guard Mode on the switch. disable(2) - disables BPDU Guard Mode on the switch. The default status is disabled. This functionality is now handled by agentStpBpduGuardMode Enumeration: 'enable': 1, 'disable': 2.

The spanning tree BPDU Filter Mode, it enables BPDU Filter on all edge ports. enable(1) - enables BPDU Filter Mode on the switch. disable(2) - disables BPDU Filter Mode on the switch. The default status is disabled. This functionality is now handled by agentStpBpduFilterDefault Enumeration: 'enable': 1, 'disable': 2.

The switch's address aging timeout table

Aging information about a specific Filtering Database.

The FDB entry's address aging timeout (in seconds)

The switch's static Mac filtering table

Per-port ingress/egress filter configuration based on VLAN Id and MAC address.

The Static MAC Filter Vlan Id

The Static MAC Filter MAC address

The Static MAC Filter source port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

The Static MAC Filter destination port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table. Configuring destination port mask for a unicast MAC filter is not supported on some platforms.

The Static MAC Filter status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry

A table of the IGMP/MLD Snooping Global configuration entries.

Represents entry for Snooping switch Configuration.

The protocol type of network protocol in use.

This enables or disables Snooping on the system. Enumeration: 'enable': 1, 'disable': 2.

IGMP/MLD Snooping Port Mask. This allows configuration of IGMP/MLD Snooping on selected ports. IGMP Snooping cannot be enabled on an interface that has routing enabled, or is a member of a LAG. If a port which has IGMP Snooping enabled becomes enabled for routing, or is enlisted as a member of a LAG, IGMP Snooping functionality will be disabled on that port. IGMP Snooping functionality will be subsequently be reenabled if routing is disabled or LAG membership is removed from an interface that had previously had IGMP Snooping enabled. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU.

A table of the IGMP Snooping Interface configuration entries.

Represents entry for a IGMP Snooping Interface.

The port number to be selected. Each port maps to an interface.

This enables or disables IGMP Snooping on a selected interface. Enumeration: 'enable': 1, 'disable': 2.

The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the entry. This value must be greater than agentSwitchIGMPSnoopingIntfMaxResponseTime.

The amount of time in seconds a switch will wait after sending a query on the selected interface because it did not receive a report for a particular group in that interface. This value must be less than agentSwitchIGMPSnoopingIntfGroupMembershipInterval.

The amount of time in seconds that a switch will wait for a query to be received on the selected interface before the interface is removed from the list of interfaces with multicast routers attached.

This enables or disables IGMP Snooping on the selected interface. Enumeration: 'enable': 1, 'disable': 2.

This enables or disables Multicast Routing on the selected interface. Enumeration: 'enable': 1, 'disable': 2.

This field lists all the VlanIDs which include the selected interface.

A table of the IGMP Snooping Vlan configuration entries.

Represents entry for a IGMP Snooping Vlan.

This enables or disables IGMP Snooping on a selected Vlan interface. Enumeration: 'enable': 1, 'disable': 0.

The amount of time in seconds that a switch will wait for a report from a particular group on the selected vlan before deleting the interface participating in the vlan from the entry. This value must be greater than agentSwitchIGMPSnoopingIntfMaxResponseTime.

The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This value must be less than agentSwitchIGMPSnoopingIntfGroupMembershipInterval.

This enables or disables IGMP Snooping on the selected vlan. Enumeration: 'enable': 1, 'disable': 0.

The amount of time in seconds that a switch will wait for a query to be received on the selected interface participating in the vlan before the interface is removed from the list of interfaces with multicast routers attached. This parameter is configurable only for exisiting Vlans.

A table of the IGMP Static Mrouter Configuration parameters.

Represents entry for a IGMP Static Mrouter.

This enables or disables IGMP Mrouter on a per-interface per-vlan basis. Enumeration: 'enable': 1, 'disable': 0.

The Multicast Forwarding Database table

Contains Forwarding and Filtering information per Vlan Index, MAC Address, and Component User.

Vlan Index for which this entry is associated with.

A multicast MAC address for which the switch has forwarding and or filtering information.

The component that is responsible for this entry in the Multicast Forwarding Database. Enumeration: 'gmrp': 2, 'static': 1, 'mld': 4, 'igmp': 3.

This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol Enumeration: 'dynamic': 2, 'static': 1.

Text description of this multicast table entry.

BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

The Multicast Forwarding Database Summary table

Summarizes the forwarding ports for all components registered for all MFDB table entries with the same Vlan Index and MAC Address.

Vlan Index for which this entry is associated with.

A multicast MAC address for which the switch has forwarding and or filtering information.

Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

This displays the maximum number of entries that can possibly be in the Multicast Forwarding Database table.

This displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high-water mark.

This displays the current number of entries in the Multicast Forwarding Database table.

Configures the Double Vlan Tag Ethertype for the switch. If this object is supported, ethertype cannot be configured per port. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).

Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports. Enumeration: 'enable': 1, 'disable': 2.

The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the broadcast traffic. Enumeration: 'enable': 1, 'disable': 2.

Configures the broadcast storm recovery threshold for this port as a percentage of port speed.

The switch config multicast allows you to enable or disable multicast storm recovery mode. When you specify Enable for multicast Storm Recovery and the multicast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the multicast traffic. Enumeration: 'enable': 1, 'disable': 2.

Configures the multicast storm recovery threshold for this port as a percentage of port speed.

The switch config unicast allows you to enable or disable unicast storm recovery mode. When you specify Enable for unicast Storm Recovery and the unknown unicast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the unknown unicast traffic. Enumeration: 'enable': 1, 'disable': 2.

Configures the unicast storm recovery threshold for this port as a percentage of port speed.

Configures the units of the threshold value to percentage of port speed or absolute packets per second. Enumeration: 'pps': 2, 'percent': 1.

Configures the units of the threshold value to percentage of port speed or absolute packets per second. Enumeration: 'pps': 2, 'percent': 1.

Configures the units of the threshold value to percentage of port speed or absolute packets per second. Enumeration: 'pps': 2, 'percent': 1.

The switch's MAC To VLAN association table

VLAN to be assigned to untagged or priority tagged packets based on MAC address.

The Mac address

The VLAN the Mac address assigned to

The Mac to VLAN association row status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry

The switch's protected port mapping table

Protected ports assigned to groups.

The group that this port belongs to

The name of the group

The set of ports that are protected in this group

The switch's Subnet To VLAN association table

VLAN to be assigned to untagged or priority tagged packets based on IP address and Subnet Mask.

The ip address

The subnet mask

The VLAN that the IP address and subnet mask assigned to

The Subnet to VLAN association row status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry

A table of the IGMP/MLD Snooping Querier Global configuration entries.

Represents entry for Snooping Querier Configuration.

This enables or disables Snooping Querier on the system. Enumeration: 'enable': 1, 'disable': 2.

This specifies the multicast protocol versions that are supported by the system.

This specifies the default source ip address to be used while generating general queries.

This specified the timer interval after which the system generates general queries.

This specified the timer interval after which the detected other querier information is no longer valid.

A table of the Snooping Querier Vlan configuration entries.

Represents entry for a Snooping Querier configurable Vlan.

This enables or disables Snooping Querier on a selected Vlan interface. Enumeration: 'enable': 1, 'disable': 0.

This specifies the current state of the Snooping Querier on a selected vlan interface Enumeration: 'disabled': 0, 'non-querier': 2, 'querier': 1.

This enables or disables the Snooping Querier Election Participation mode. When enabled snooping querier switch will participate in querier election up on discovering another querier in the specified vlan. When disabled, up on discovering another querier, snooping querier moves to non-querier state. Enumeration: 'enable': 1, 'disable': 0.

This specifies the default source ip address to be used while generating general queries on the specified vlan.

This specifies the multicast protocol version that is currently being used by the snooping switch for the specified vlan while generating query messages.

The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This object is valid only when agentSwitchSnoopingQuerierOperVersion object is valid. (-1) - indicates that parameter is not available; ( 0) - indicates that response time is less then 1 second.

This specifies the last querier's ip address for the specified vlan. It represents the detected other multicast querier in the vlan.

This specifies the multicast protocol version that is currently being used by the detected other multicast querier for the specified vlan. (-1) - indicates that parameter is not available.

This enables or disables Voice VLAN on the system. Enumeration: 'enable': 1, 'disable': 2.

A table of the Voice Vlan device entries.

Represents entry for a Voice Device on the interface.

The interface number of this interface.

The Voice Device Mac address

This object indicates whether Sender MAC validation in the ARP packets is enabled. If this object is set to 'true', validation is enabled. If this object is set to 'false', validation is disabled.

This object indicates whether Target MAC validation in the ARP Response packets is enabled. If this object is set to 'true', validation is enabled. If this object is set to 'false', validation is disabled.

This object indicates whether IP address validation in the ARP packets is enabled. If this object is set to 'true', validation is enabled. If this object is set to 'false', validation is disabled.

A table provides the mechanism to control Dynamic ARP Inspection per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added.

A row instance contains the configuration for Dynamic ARP Inspection at each existing VLAN.

This object indicates the VLAN number on which Dynamic ARP Inspection feature is configured.

This object indicates whether Dynamic ARP Inspection is enabled in this VLAN. If this object is set to 'true', Dynamic ARP Inspection is enabled. If this object is set to 'false', Dynamic ARP Inspection is disabled.

This object indicates whether the Dynamic ARP Inspection logging is enabled on this VlAN. If this object is set to 'true', Dynamic ARP Inspection logging is enabled. If this object is set to 'false', Dynamic ARP Inspection loging is disabled.

This object indicates the ARP ACL name set for this VLAN.

This object indicates whether the ARP ACL set for this VLAN has static flag set. If this object is set to 'true', static flag is enabled. If this object is set to 'false', static flag is disabled.

Clear the DAI statistics on all vlans. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator. Enumeration: 'reset': 1, 'none': 0.

A table provides the mechanism to control Dynamic ARP Inspection per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added.

A row instance contains the Dynamic ARP Inspection statistics per VLAN.

This object indicates the VLAN number on which Dynamic ARP Inspection statistics are retrieved.

Number of valid ARP packets forwarded by DAI.

Number of invalid ARP packets dropped by DAI.

Number of ARP packets that were dropped by DAI as there is no matching DHCP Snooping binding entry found.

Number of ARP packets that were forwarded by DAI as there is a matching DHCP Snooping binding entry found.

Number of ARP packets that were dropped by DAI as there is no matching ARP ACL rule found for this Vlan and the static flag is set on this vlan.

Number of ARP packets that were permitted by DAI as there is a matching ARP ACL rule found for this Vlan.

Number of ARP packets that were dropped by DAI as the sender mac address in ARP packet didn't match the source mac in ethernet header.

Number of ARP packets that were dropped by DAI as the target mac address in ARP reply packet didn't match the destination mac in ethernet header.

Number of ARP packets that were dropped by DAI as the sender IP address in ARP packet or target IP address in ARP reply packet is invalid. Invalid addresses include 0.0.0.0, 255.255.255.255, IP multicast addresses, class E addresses (240.0.0.0/4), loopback addresses (127.0.0.0/8).

A table provides the mechanism to configure the trust state for Dynamic ARP Inspection purpose at each physical interface capable of this feature.

A row instance contains the configuration for Dynamic ARP Inspection at each physical interface capable of this feature.

This object indicates whether the interface is trusted for Dynamic ARP Inspection purpose. If this object is set to 'true', the interface is trusted. ARP packets coming to this interface will be forwarded without checking. If this object is set to 'false', the interface is not trusted. ARP packets coming to this interface will be subjected to ARP inspection.

This object indicates rate limit value for Dynamic ARP Inspection purpose. If the incoming rate of ARP packets exceeds the value of this object for consecutively burst interval seconds, ARP packets will be dropped.

This object indicates the burst interval value for rate limiting purpose on this interface.

A table of the ARP ACL entries

Represents entry for an ARP ACL

Name of the ARP ACL, which must consist of 1 to 31 alphanumeric characters and uniquely identify this ARP ACL. This object must be set to complete a new ARP ACL row instance.

The status of this conceptual row. Entries can not be deleted until all rows in arpAclRuleTable with corresponding values of arpAclIndex have been deleted. active(1) - this ACL instance is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance

A table of the ARP ACL Rule entries

Represents entry for a set of ARP ACL-match rules

Sender IP address match value for the ARP ACL.

Sender MAC address match value for the ARP ACL.

The status of this conceptual row. active(1) - this ACL Rule is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance

This object indicates whether DHCP Snooping is enabled globally. If this object is set to 'true',admin mode is enabled globally. If this object is set to 'false',admin mode is disabled globally.

This object indicates whether source Mac address in the received DHCP Message needs to be verified or not. If this object is set to 'true',verifyMac is enabled globally. If this object is set to 'false',verifyMac is disabled globally.

A table provides the mechanism to control DHCP SNOOPING per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added.

A row instance contains the configuration for DHCP SNOOPING at each existing VLAN.

This object indicates the VLAN number on which DHCP SNOOPING Inspection feature is configured.

This object indicates whether DHCP SNOOPING is enabled in this VLAN. If this object is set to 'true', DHCP SNOOPING is enabled. If this object is set to 'false', DHCP SNOOPING is disabled.

A table provides the mechanism to configure the trust state for DHCP snooping purpose at each physical interface capable of this feature.

A row instance contains the configuration for DHCP snooping at each physical interface capable of this feature.

This object indicates whether the interface is trusted for DHCP snooping purpose.

This object indicates whether the Logging needs on DHCP snooping validations or not

This object indicates rate limit value for DHCP Snooping purpose. If the incoming rate of DHCP packets exceeds the value of this object for consecutively burst interval seconds, DHCP packets will be dropped.

This object indicates the burst interval value for rate limiting purpose on this interface.

Clear the DHCP snooping statistics on all ports. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator. Enumeration: 'reset': 1, 'none': 0.

A table provides the mechanism for statics of DHCP snooping.

A row instance contains the DHCP snooping statistics per VLAN.

This object indicates the number of failure verifications of client mac address with source mac address

This object indicates the number of invalid DHCP releases and denay messages

This object indicates the number of invalid DHCP server mesaages

A table of the DHCP SNOOPING static entries

Represents a binding in DHCP SNOOPING table

Interface on which this DHCP SNOOPING binding is going to be added.

VLAN to which this DHCP SNOOPING binding is going to be added.

MAC address match value for the DHCP SNOOPING Binding.

IP address match value for the DHCP SNOOPING Binding.

The status of this conceptual row. active(1) - this DHCP SNOOPING Binding is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance

A table of the DHCP SNOOPING Dynamic entries

Represents a binding in DHCP SNOOPING table

Interface on which this DHCP SNOOPING binding is going to be added.

VLAN to whcig this DHCP SNOOPING binding is going to be added.

MAC address match value for the DHCP SNOOPING Binding.

IP address match value for the DHCP SNOOPING Binding.

This specifies the period for which the DHCP SNOOPING Binding is valid.

Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM, TFTP, SFTP or SCP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port. on the Linux platform. SFTP and SCP are only allowed if the SSH feature is present. Enumeration: 'sftp': 5, 'xmodem': 2, 'tftp': 1, 'scp': 6, 'zmodem': 4, 'ymodem': 3.

Transfer upload server ip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP, SFTP, or SCP. The address is 4 integer bytes ranging from 0 to 255. This object is deprecated in favour of agentTransferUploadServerAddress and agentTransferUploadServerAddressType.

Transfer upload tftppath configures the directory path where the file is to be uploaded to. The switch remembers the last file path used.

Transfer upload tftpfilename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.

Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Code File - Configuration File - Operational log - Startup log Enumeration: 'operationallog': 4, 'code': 2, 'config': 3, 'startuplog': 5.

Transfer upload start will start an upload transfer. The agentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP. Enumeration: 'enable': 1, 'disable': 2.

Indicates the current status of an upload transfer. Enumeration: 'writingToFlash': 7, 'wrongFileType': 4, 'updatingConfig': 5, 'notInitiated': 1, 'errorStarting': 3, 'invalidConfigFile': 6, 'transferStarting': 2, 'checkingCRC': 9, 'transferSuccessful': 12, 'failureWritingToFlash': 8, 'transferFailed': 13, 'failedCRC': 10, 'unknownDirection': 11.

The type of the tftpserverip address, as defined in the InetAddress MIB. The agentTransferUploadServerAddress object is intepreted within the context of agentTransferUploadServerAddressType. Only ipv4(1) and ipv6(2) is supported at present.

Transfer upload tftpserverip configures the IP address of the server where the file is to be uploaded to.It is valid only when the Transfer Mode is TFTP. The type of this address is determined by the value of the agentTransferUploadServerAddressType object. The values for agentTransferUploadServerAddressType and agentTransferUploadServerAddress must be consistent.

Transfer upload image name. Sets the image to be uploaded as the specified name Note: Imagename, File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP. Enumeration: 'image2': 3, 'image1': 2.

Username applicable only to secure upload types, i.e., SFTP or SCP.

Password applicable only to secure upload types, i.e. SFTP or SCP.

Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM, TFTP, SFTP or SCP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port. Y/ZMODEM is valid only on the Linux platform. SFTP and SCP are only allowed if the SSH feature is present. Enumeration: 'sftp': 5, 'xmodem': 2, 'tftp': 1, 'scp': 6, 'zmodem': 4, 'ymodem': 3.

Transfer download tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP, SFTP or SCP. The address is 4 integer bytes ranging from 0 to 255. This object is deprecated in favour of agentTransferDownloadServerAddress and agentTransferDownloadServerAddressType.

Transfer download tftppath configures the directory path where the file is located. The switch remembers the last file path used.

Transfer download tftpfilename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 33 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: Imagename, File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.

Transfer download datatype configures the type of file to download to the switch. The types for download are: code - Code File config - Configuration File sshkey-rsa1 - SSH-1 RSA Key File sshkey-rsa2 - SSH-2 RSA Key PEM File sshkey-dsa - SSH-2 DSA Key PEM File sslpem-root - SSL Trusted Root Certificate PEM File sslpem-server - SSL Server Certificate PEM File sslpem-dhweak - SSL DH Weak Encryption Parameter PEM File sslpem-dhstrong - SSL DH Strong Encryption Parameter PEM File cli-banner - CLI Banner File kernel - Kernel File Note: SSH Key files can only be downloaded if SSH Server is administratively disabled, and there are no active SSH sessions. Kernel file can be downloaded only on raptor platform and linux operating system. Enumeration: 'sslpem-server': 8, 'code': 2, 'kernel': 12, 'sshkey-dsa': 6, 'sslpem-dhweak': 9, 'clibanner': 11, 'sslpem-dhstrong': 10, 'sshkey-rsa1': 4, 'sshkey-rsa2': 5, 'sslpem-root': 7, 'config': 3.

Transfer download start will start an download transfer. The agentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP. Enumeration: 'enable': 1, 'disable': 2.

Indicates the current status of an download transfer. Enumeration: 'writingToFlash': 7, 'wrongFileType': 4, 'updatingConfig': 5, 'notInitiated': 1, 'errorStarting': 3, 'invalidConfigFile': 6, 'transferStarting': 2, 'checkingCRC': 9, 'transferSuccessful': 12, 'failureWritingToFlash': 8, 'transferFailed': 13, 'failedCRC': 10, 'unknownDirection': 11.

The type of the tftpserverip address, as defined in the InetAddress MIB. The agentTransferDownloadServerAddress object is intepreted within the context of agentTransferDownloadServerAddressType. Only ipv4(1) and ipv6(2) is supported at present.

Transfer download tftpserverip configures the IP address of the server where the file is to be downloaded from.It is valid only when the Transfer Mode is TFTP. The type of this address is determined by the value of the agentTransferDownloadServerAddressType object. The values for agentTransferDownloadServerAddressType and agentTransferDownloadServerAddress must be consistent.

Transfer download image name. Sets the downloaded image as the specified name Note: Imagename, File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP. Enumeration: 'image2': 3, 'image1': 2.

Username applicable only to secure download types, i.e., SFTP or SCP.

Password applicable only to secure download types, i.e. SFTP or SCP.

The image1 software version .

The image2 software version.

The active image name. image1 or image2.

The next active image name. user assigns either image1 or image2.

IfIndex of the mirrored port

IfIndex of the probe port

Port mirroring mode: enable - enable mirroring mode disable - disable mirroring mode delete - clear MirroredPort and Probe Port configuration Enumeration: 'enable': 1, 'disable': 2, 'delete': 3.

This table includes entries for each Port Mirroring session.

Provides configuration of a Port Mirroring session specifying the destination port, and the source Port Mask, providing a many-to-one mapping.

The Session number of this mirroring entry. The number of sessions is fixed, and is platform dependant.

The port which traffic from the mirrored ports will be sent to.

The ports from which traffic will be sent to the destination port. The destination port can not be included in this list of ports.

The status of this port mirroring session. enable(1) - This session is active and all traffic from the source ports will be mirrored to the destination port. disable(2) - This session is not active. delete(3) - Remove the configuration for this Session Enumeration: 'enable': 1, 'disable': 2, 'delete': 3.

This table includes entries for each source port's direction of port mirroring.

Provides configuration of a Port Mirroring direction specifying the session of the port mirroring and source port

The port from which traffic will be sent to the destination port. This port should be a source port in the corresponding session

The direction of the data to be mirrored on this source port. tx(1) - The data that is transmitted from the source port. rx(2) - The data that is received on the source port. txrx(3) - The data that is transmitted/received from/on the source port Enumeration: 'rx': 2, 'txrx': 3, 'tx': 1.

This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB.

Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port.

ifIndex of this physical port

Enable/disable 802.3ad LACP on this port Enumeration: 'enable': 1, 'disable': 2.

A table of the switch's physical port config entries

Switch's physical port config entry

The port number of this port.

The switch's Port IfIndex

The switch's Port Type

The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port This object is only supported when the Dot1d Protocol is enabled. Enumeration: 'dot1d': 1, 'off': 3, 'fast': 2.

The switch's Port Spanning Tree Protocol State. This object is only supported when the Dot1d Protocol is enabled. Enumeration: 'disabled': 5, 'learning': 3, 'forwarding': 4, 'blocking': 1, 'listening': 2.

The switch's Port Admin Mode Enumeration: 'enable': 1, 'disable': 2.

The switch's Port Speed Mode. This is the configured physical mode. This object is read-only for gigabit ports Enumeration: 'half-10': 2, 'full-10gsx': 9, 'full-100': 5, 'full-1000sx': 8, 'full-100fx': 7, 'auto-negotiate': 1, 'half-100fx': 6, 'full-10': 3, 'half-100': 4.

The switch's Port Physical Speed Status. This is the current actual speed. Enumeration: 'half-10': 2, 'full-10gsx': 9, 'full-100': 5, 'full-1000sx': 8, 'full-100fx': 7, 'auto-negotiate': 1, 'half-100fx': 6, 'full-10': 3, 'half-100': 4.

If enabled, link up and link down traps will be sent for this port. Enumeration: 'enable': 1, 'disable': 2.

clear stats for this port only Enumeration: 'enable': 1, 'disable': 2.

This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. The set of possible values for this object is the same as the set defined for the agentPortType object. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType10GBaseSX

This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object agentPortDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object agentPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD dot3MauType10GBaseSX

This object identifies the administration status of auto negotiation for this port. Enumeration: 'enable': 1, 'disable': 2.

Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports. Enumeration: 'enable': 1, 'disable': 2.

Controls the Double Vlan Tag mode on this port. Enumeration: 'enable': 1, 'disable': 2.

Configures the Double Vlan Tag Ethertype for this port. If this object is supported, ethertype cannot be configured globally for the switch. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).

Configures the Customer ID for the Double Vlan Tag for this port.

This object identifies the largest value that can be configured for agentPortMaxFrameSize

This object identifies the currently configured maximum frame size value for this port. The maximmum value that this object can be set to is the value of agentPortMaxFrameSizeLimit. For Ethernet ports which support 802.1Q vlan tagging, the minimum value that this object can be set to is 1522

If enabled, broadcast storm recovery will function on this port. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on this Ethernet port exceeds the configured threshold, the switch blocks (discards) the broadcast traffic. Enumeration: 'enable': 1, 'disable': 2.

Configures the broadcast storm recovery threshold for this port as a percentage of port speed.

If enabled, multicast storm recovery will function on this port. When you specify Enable for Multicast Storm Recovery and the multicast traffic on this Ethernet port exceeds the configured threshold, the switch blocks (discards) the multicast traffic. Enumeration: 'enable': 1, 'disable': 2.

Configures the multicast storm recovery threshold for this port as a percentage of port speed.

If enabled, unicast storm recovery will function on this port. When you specify Enable for Unicast Storm Recovery and the unknown unicast traffic on this Ethernet port exceeds the configured threshold, the switch blocks (discards) the unknown unicast traffic. Enumeration: 'enable': 1, 'disable': 2.

Configures the unicast storm recovery threshold for this port as a percentage of port speed.

Enumeration: 'access': 1, 'general': 3, 'trunk': 2.

Describes and Configures the Port Voice VLAN Mode. Enumeration: 'untagged': 4, 'none': 1, 'disable': 5, 'vlanid': 2, 'dot1p': 3.

Describes and Configures the Port Voice VLAN ID if the Voice Vlan Mode is Vlan ID.

Describes and Configures the Port Voice VLAN Priority if the Voice Vlan Mode is dot1p. A value of 255 indicates that the priority is not configured.

Describes and Configures the Port Voice VLAN Data Priority Mode. Enumeration: 'untrust': 2, 'trust': 1.

Describes the Port Voice VLAN Operational Status. Enumeration: 'disabled': 2, 'enabled': 1.

Describes and Configures the Port Voice VLAN Authentication Mode. It is enabled by default. To disable, following are the pre-requisites. Voice Vlan shall be enabled Globally, Dot1x Admin Mode shall be enabled, Dot1x port-control shall be mac-based, and the port is required to be in General Mode. Enumeration: 'enable': 1, 'disable': 2.

This object identifies operational status of the flow control per port. Enumeration: 'active': 1, 'inactive': 2.

Firmware part number of 10GBASE-T transceiver. For other ports, or if module is not inserted, octet sting will be filled with 0xFF bytes. See also next field, agentPortTransceiverFwRevision. PN is an 8-byte field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces (0x20). A field value of all zeros indicates that PN is unspecified.

Firmware revision of 10GBASE-T transceiver. For other ports, or if module is not inserted, octet sting will be filled with 0xFF bytes. See also previous field, PortTransceiverFwPartNumber. Rev is a 4-byte field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces (0x20). A field value of all zeros indicates that Rev is unspecified.

Configures the units of the threshold value to percentage of port speed or absolute packets per second. Enumeration: 'pps': 2, 'percent': 1.

Configures the units of the threshold value to percentage of port speed or absolute packets per second. Enumeration: 'pps': 2, 'percent': 1.

Configures the units of the threshold value to percentage of port speed or absolute packets per second. Enumeration: 'pps': 2, 'percent': 1.

Describes and Configures the Port Voice VLAN tagging mode. Enumeration: 'true': 1, 'false': 0.

Describes and Configures the Port Voice VLAN None mode. Enumeration: 'true': 1, 'false': 0.

Describes and Configures the Port Voice VLAN DSCP value.

Describes and Configures the Port Voice VLAN Authentication mode. Disable means authentication not required for voice devices when dot1x is enabled. Enumeration: 'enable': 1, 'disable': 2.

Describes and Configures the VLAN ID of access switch port. A value of 0 indicates that the switch port is not configured as access port.

Set to non-empty string to create a Protocol-Based VLAN group.

A table of the switch's Protocol-based VLAN entries

Switch's Protocol-based VLAN entry

Group identifier of the Protocol-based VLAN entry.

Group name of the Protocol-based VLAN entry.

VLAN associated with the Protocol-based VLAN entry. Set to 0 to remove.

The status of the IP protocol association with the Protocol-based VLAN entry. Enumeration: 'enable': 1, 'disable': 2.

The status of the ARP protocol association with the Protocol-based VLAN entry. Enumeration: 'enable': 1, 'disable': 2.

The status of the IPX protocol association with the Protocol-based VLAN entry. Enumeration: 'enable': 1, 'disable': 2.

The status of the Protocol-based VLAN entry. active(1) - this entry is active destroy(6) - remove this entry

A table of the switch's physical port config entries

Switch's physical port config entry

The interface number of this instance.

The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to this group destroy(6) - remove the port from this group

The MST configuration digest key.

The MST configuration format selector. A value other than 0 (zero) indicates non-support for the IEEE 802.1s standard.

The MST configuration name of at most 32 characters.

The MST configuration revision. The default value is 0.

The MST configuration force protocol version. The default version is dot1w. Enumeration: 'dot1w': 2, 'dot1d': 1, 'dot1s': 3.

The spanning tree operational status. enable(1) - enables spanning tree operational status on the switch. disable(2) - disables spanning tree operational status on the switch. The default status is enabled. Enumeration: 'enable': 1, 'disable': 2.

STP port table.

STP port entry.

The administrative STP state for the port. enable(1) - enables STP on the port. disable(2) - disables STP on the port. The default port STP state is enabled for the first 4095 ports and disabled for any ports beyond. Enumeration: 'enable': 1, 'disable': 2.

The MSTP BPDUs received on a specific port.

The MSTP BPDUs sent from a specific port.

The RSTP BPDUs received on a specific port.

The RSTP BPDUs sent from a specific port.

The STP BPDUs received on a specific port.

The STP BPDUs sent from a specific port.

Time since port was reset. It is displayed in days, hours, minutes, and seconds.

Force the specified port to transmit RSTP or MSTP BPDU's. Supported values: false(0) - BPDUs are not to be transmitted. true(1) - BPDUs are to be transmitted A non-zero value indicates that BPDUs are to be sent on the specified port. Enumeration: 'true': 1, 'false': 0.

Manage root-guard on the specified interface. Supported values: false(0) - Root-guard is disabled. true(1) - Root-guard is enabled. Enumeration: 'true': 1, 'false': 0.

The MSTP root port hello time for the CIST.

The MSTP root port max age for the CIST.

The MSTP regional root identifier for the CIST.

The MSTP regional root path cost for the CIST.

The MSTP root port forward delay for the CIST.

The MSTP bridge forward delay for the CIST. The default value is 15. This value must be >= ((MSTP root port max age/2) + 1).

The MSTP bridge hello time for the CIST. The default value is 2.

The MSTP bridge hold time for the CIST.

The MSTP bridge max age for the CIST. The default value is 20.

The MSTP bridge max hops for the CIST. The default value is 20.

The MSTP bridge priority for the CIST. The default value is 32768.

The MSTP bridge hold count for the CIST. This command sets the value of maximum bpdus that a bridge is allowed to send within a hello time window. The default value is 6.

CIST port table.

CIST port entry.

The MSTP operational status of a specific port for the CIST. Enumeration: 'enable': 1, 'disable': 2.

The MSTP operational point to point mac of a specific port for the CIST. Enumeration: 'false': 2, 'true': 1.

The MSTP topology change acknowledge for a specific port in the CIST. Enumeration: 'false': 2, 'true': 1.

The administrative state of a specific port in CIST. enable(1) - enables the port. disable(2) - disables the port. The default port state is disabled. For the M6220, the default port state is enabled for internal ports and disabled for external ports. Enumeration: 'enable': 1, 'disable': 2.

The MSTP forwarding state of a specific port in CIST. Enumeration: 'manualFwd': 5, 'notParticipate': 6, 'discarding': 1, 'disabled': 4, 'learning': 2, 'forwarding': 3.

The MSTP port identifier of a specific port in CIST.

The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.

The MSTP port priority in CIST. The priority is in the increments of 16. The default value is 128.

The MSTP designated bridge ID of a specific port in CIST.

The MSTP designated cost of a specific port in CIST.

The MSTP designated port ID of a specific port in CIST.

The MSTP external port path cost in CIST. The default value varies depending upon the link speed.

BPDU Guard Mode effect on the port. enable(1) - BPDU Guard Mode is enabled on the port. disable(2) - BPDU Guard Mode is disabled on the port. Enumeration: 'enable': 1, 'disable': 2.

This command sets BPDU Filter mode on the port. enable(1) - BPDU Filter Mode is enabled on the port. disable(2) - BPDU Filter Mode is disabled on the port. Enumeration: 'enable': 1, 'disable': 2.

This command sets BPDU Flood mode on the port. enable(1) - BPDU Flood Mode is enabled on the port. disable(2) - BPDU Flood Mode is disabled on the port. Enumeration: 'enable': 1, 'disable': 2.

This command sets the auto-edge mode of the port which enables it to become an edge port if it does not see BPDUs for some duration. enable(1) - enables the auto-edge mode for the port. disable(2) - disables the auto-edge mode for the port. The default auto-edge mode is disabled. Enumeration: 'enable': 1, 'disable': 2.

This command sets a port to discard any superior information received by the port and thus protect against root of the device from changing.The port gets put into discarding state and does not forward any packets. enable(1) - enables the root-guard mode for the port. disable(2) - disables the root-guard mode for the port. The default root-guard mode is disabled. Enumeration: 'enable': 1, 'disable': 2.

This command restricts the port from propagating any topology change information received through that port. enable(1) - enables the tcn-guard mode for the port. disable(2) - disables the tcn-guard mode for the port. The default tcn-guard mode is disabled. Enumeration: 'enable': 1, 'disable': 2.

This command enables loop guard on this port. This setting applies to all Spanning Tree instances of which this port is a member. enable(1) - enables the loop guard mode for the port. disable(2) - disables the loop guard mode for the port. The default loop-guard mode is disabled. Enumeration: 'enable': 1, 'disable': 2.

MST table.

MST entry.

The MSTP instance ID.

The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768.

The MSTP bridge identifier in a specific instance.

The MSTP designated root bridge identifier in a specific instance.

The MSTP root path cost in a specific instance.

The MSTP root port ID in a specific instance.

The MSTP time since the last topology change in a specific instance.

The MSTP count of topology changes in a specific instance.

The MSTP topology change parameter in a specific instance. Enumeration: 'false': 2, 'true': 1.

The MSTP instance status. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance.

MST port table.

MST port entry.

The MSTP forwarding state of a specific port in a specific instance. Enumeration: 'manualFwd': 5, 'notParticipate': 6, 'discarding': 1, 'disabled': 4, 'learning': 2, 'forwarding': 3.

The MSTP port identifier of a specific port in a specific instance.

The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.

The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128.

The MSTP designated bridge ID of a specific port in a specific instance.

The MSTP designated cost of a specific port in a specific instance.

The MSTP designated port ID of a specific port in a specific instance.

The loop inconsistent state of a specific port in a specific instance. This value can only report as true(1) when loop guard is enabled on the port and the port has transitioned from blocking state in this MST instance. Enumeration: 'true': 1, 'false': 0.

The number of times this interface has transitioned into loop inconsistent state.

The number of times this interface has transitioned out of loop inconsistent state.

MST VLAN table.

MST VLAN entry.

The association status of an MSTP instance and a VLAN. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - used to create a new association between an MSTP instance and a VLAN. destroy(6) - removes the association between an MSTP instance and a VLAN.

The spanning tree BPDU Guard Mode. enable(1) - enables BPDU Guard Mode on the switch. disable(2) - disables BPDU Guard Mode on the switch. The default status is disabled. Enumeration: 'enable': 1, 'disable': 2.

The spanning tree BPDU Filter Mode, it enables BPDU Filter on all edge ports. enable(1) - enables BPDU Filter Mode on the switch. disable(2) - disables BPDU Filter Mode on the switch. The default status is disabled. Enumeration: 'enable': 1, 'disable': 2.

Authentication List Create If set to a non empty string, creates a new Authentication List for configuration.

MST VLAN table.

MST VLAN entry.

Authenticaiton List Index Unique number used for indexing into this table.

Authenticaiton List Name Unique name used to identify the Authentication List from other tables.

Authenticion List Method 1 Configures the first authentication method to use when this list is specified. Enumeration: 'none': 4, 'enable': 1, 'tacacs': 6, 'radius': 5, 'line': 2, 'local': 3.

Authenticion List Method 2 Configures the second authentication method to use when this list is specified. Enumeration: 'none': 4, 'enable': 1, 'tacacs': 6, 'radius': 5, 'line': 2, 'local': 3.

Authenticion List Method 3 Configures the third authentication method to use when this list is specified. Enumeration: 'none': 4, 'enable': 1, 'tacacs': 6, 'radius': 5, 'line': 2, 'local': 3.

The status of the Authentication List. Supported values: active(1) - indicates a valid Authenticaiton List destroy(6) - removes the Authentication List.

Authenticion List Method 4 Configures the fourth authentication method to use when this list is specified. Enumeration: 'none': 4, 'enable': 1, 'tacacs': 6, 'radius': 5, 'line': 2, 'local': 3.

Default Authentication List This object configures which authentication list to use for users which do not have an Authentication List configured. The list must be configured before setting.

User Authentication Config Table

User Authentication Config Entry

User Authentication List This object configures which authentication list to use for this user. The list must be configured before setting.

User Port Config Table

User Port Config Entry

User Port Port Security This object configures which ports the user has access to. Ports are indexed based on dot1dBasePort entries in dot1dBasePortTable.

A table that contains information about the 802.1p priority mapping to traffic class priority queue for every physical port.

A 802.1p priority mapped to a traffic class priority queue.

The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type. For untagged frames received from Ethernet media, this value is equal to the dot1dPortDefaultUserPriority value for the ingress port.

Traffic class priority queue the received frame is mapped to.

A table for link dependencies entries.

Link Dependency Group Entry.

Group identifier of the Link Dependency entry. Maximum of 16 group entries exists on the switch but they are not configured on the switch. Groups are configured only when member ports are added to the group or ports dependent on member ports are added to the group.

The status of this entry. active(1) - the group has a valid configuration notReady(3) - the group has an incomplete configuration destroy(6) - remove the group destroy is the only RowStatus which can be set. The others are read-only.

Member Port Mask. This mask defines the member ports of this group. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

Depended Upon Port Mask. This mask defines the ports upon which the members of this group depend. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

Group action refers to action taken by the dependent ports when the member ports go down. LINK-DOWN(0) members go down when dependent link goes down, LINK-UP(1) members go up when dependent link goes down

Configures the HTTP server admin mode Enumeration: 'enable': 1, 'disable': 2.

Configures the use of the Java interface through Web connections. Enumeration: 'enable': 1, 'disable': 2.

Configures the maximum number of allowable HTTP sessions. The default value is 16.

Configures the hard timeout for HTTP sessions in hours. The default value is 24 hours. A value of 0 gives an infinite timeout.

Configures the soft (activity) timeout for HTTP sessions in minutes. The default value is 5 minutes. A value of 0 gives an infinite timeout.

Enable/Disable Autoinstall on device. Enumeration: 'enable': 1, 'disable': 2.

Enable/Disable Auto Save of downloaded configuration on device. Enumeration: 'enable': 1, 'disable': 2.

Sets number of unicast TFTP attempts for configuration file.

Display current Autoinstall status on device.

enable(1) will initiate an configuration save to nvram. Status is returned by the object agentSaveConfigStatus. Enumeration: 'enable': 1, 'disable': 2.

clear config to factory defaults Enumeration: 'enable': 1, 'disable': 2.

clear lag configuration Enumeration: 'enable': 1, 'disable': 2.

close all telnet sessions Enumeration: 'enable': 1, 'disable': 2.

reset passwords Enumeration: 'enable': 1, 'disable': 2.

clear all port statistics Enumeration: 'enable': 1, 'disable': 2.

clear all switch statistics Enumeration: 'enable': 1, 'disable': 2.

clear trap log Enumeration: 'enable': 1, 'disable': 2.

clear vlan entries Enumeration: 'enable': 1, 'disable': 2.

Resets the switch. This object is not valid for stacking platforms. Enumeration: 'enable': 1, 'disable': 2.

Indicates the current status of an save configuration request. Enumeration: 'savingComplete': 3, 'savingInProcess': 2, 'notInitiated': 1, 'savingFailed': 4.

Status of the Virtual Cable Tester active(1) - cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed. Cannot be set. failure(3) - A failure was encountered during the test. Cannot be set. uninitialized(4) - No test has been performed yet. Cannot be set. Enumeration: 'active': 1, 'failure': 3, 'success': 2, 'uninitialized': 4.

Determines on which port to perform the cable test. Limited to copper based ports.

Indicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(3) - There is an electrical short in the cable. unknown(4) - No test has been performed yet, or a test is currently in progress. Enumeration: 'unknown': 4, 'short': 3, 'open': 2, 'normal': 1.

The estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if agentCableTesterStatus is not success(2) or the cable length is unknown.

The estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if agentCableTesterStatus is not success(2) or the cable length is unknown.

The estimated distance in meters from the end of the cable to the failure location. This object will return 0 if agentCableTesterStatus is not success(2).