DLINK-3100-PHY-MIB: View SNMP OID List / Download MIB

VENDOR: D-LINK

Home	MIB: DLINK-3100-PHY-MIB
Download as:		SNMPv2-CONF, IF-MIB, SNMPv2-SMI, DLINK-3100-MIB, SNMPv2-TC		Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash). Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded. The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.

Object Name	OID	Type	Access	Info
rlPhy	1.3.6.1.4.1.171.10.94.89.89.90			The MIB module describes the private MIB for testing Layer1 interfaces supported by DLINK-3100's software and products.
rlPhyTest	1.3.6.1.4.1.171.10.94.89.89.90.1
rlPhyTestSetTable	1.3.6.1.4.1.171.10.94.89.89.90.1.1		no-access
rlPhyTestSetEntry	1.3.6.1.4.1.171.10.94.89.89.90.1.1.1		no-access	An entry containing objects for invoking tests on an interface.
rlPhyTestSetType	1.3.6.1.4.1.171.10.94.89.89.90.1.1.1.1	rlphytesttype	read-write	A control variable used to start operator initiated interface tests.1 indicates that no test has been initiated. Only operator initiated interface tests can be set to this variable.
rlPhyTestGetTable	1.3.6.1.4.1.171.10.94.89.89.90.1.2		no-access
rlPhyTestGetEntry	1.3.6.1.4.1.171.10.94.89.89.90.1.2.1		no-access	An entry containing results of tests on an interface.
rlPhyTestGetType	1.3.6.1.4.1.171.10.94.89.89.90.1.2.1.1	rlphytesttype	read-only	A control variable used to, 1 to indicate that this test can be done on the specified port, 2 to initiate the test whenever the user wishes
rlPhyTestGetStatus	1.3.6.1.4.1.171.10.94.89.89.90.1.2.1.2	integer	read-only	This object contains the status of the most recently requested test for operator initiated tests or the value none(1) if no tests have been requested since the last reset. For non operator initiated tests the value is always none(1). Note that this facility provides no provision for saving the results of one test when starting another, as could be required if used by multiple managers concurrently. Enumeration: 'none': 1, 'success': 2, 'failed': 7, 'unAbleToRun': 5, 'aborted': 6, 'inProgress': 3, 'notSupported': 4.
rlPhyTestGetResult	1.3.6.1.4.1.171.10.94.89.89.90.1.2.1.3	integer	read-only	This object holds the test result
rlPhyTestGetUnits	1.3.6.1.4.1.171.10.94.89.89.90.1.2.1.4	integer	read-only	The test result unit of measure. The units can be standard unit or special units that are designed for special test. The alaskaPhyLength unit is design for the VCT diagnostic and its values are: less_than_50M(1), 50-80M(2), 80-110M(3), 110-140M(4), more_than_140M(5). The alaskaPhyStatus unit is design for the VCT diagnostic and its values are: 4_pair_cable(1), 2_pair_cable(2), no_cable(3), open_cable(4), short_cable(5), bad_cable(6), impedance_mismatch(7). Enumeration: 'microVolt': 8, 'microWatt': 11, 'alaskaPhyLength': 13, 'dbm': 15, 'microAmper': 10, 'degree': 7, 'millisecond': 12, 'reverseNormal': 4, 'nanosecond': 19, 'downUP': 3, 'meter': 6, 'decidbm': 16, 'abcd': 18, 'microOham': 9, 'boolean': 2, 'milidbm': 17, 'integer': 1, 'alaskaPhyStatus': 14, 'mdiMdix': 5.
rlPhyTestGetAlarm	1.3.6.1.4.1.171.10.94.89.89.90.1.2.1.5	integer	read-only	This object hold the Alarm for this Entry. only Test that have can have alarms use this field, other holds the Value notRelevant(1) Enumeration: 'lowWarning': 3, 'highAlarm': 6, 'notRelevant': 1, 'highWarning': 4, 'lowAlarm': 5, 'noAlarmSet': 2.
rlPhyTestGetTimeStamp	1.3.6.1.4.1.171.10.94.89.89.90.1.2.1.6	displaystring	read-only	The time in string (formated DD-MMM-YYYY HH:MM:SS e.g 14-Apr-2002 10:33:31)