DGS3224-SWL3MGMT-MIB: View SNMP OID List / Download MIB

VENDOR: D-LINK


 Home MIB: DGS3224-SWL3MGMT-MIB
Download as:   
SNMPv2-CONF, IF-MIB, SNMPv2-SMI, SW3200PRIMGMT-MIB, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 swL3MgmtMIB 1.3.6.1.4.1.171.11.101.3.3
The Structure of Layer 3 Network Management Information for the proprietary enterprise.
     swL3IpMgmt 1.3.6.1.4.1.171.11.101.3.3.2
         swL3IpCtrlMgmt 1.3.6.1.4.1.171.11.101.3.3.2.1
             swL3IpCtrlTable 1.3.6.1.4.1.171.11.101.3.3.2.1.3 no-access
This table contains IP interface information.
                 swL3IpCtrlEntry 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1 no-access
A list of information about a specific IP interface.
                     swL3IpCtrlInterfaceName 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.1 displaystring read-only
This object indicates the name of the IP interface.
                     swL3IpCtrlIfIndex 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.2 integer read-only
This object uniquely identifies the IP interface number in the swL3IpCtrlTable.
                     swL3IpCtrlIpAddr 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.3 ipaddress read-write
The IP address of the interface. This object only can take the value of the unicast IP address.
                     swL3IpCtrlIpSubnetMask 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.4 ipaddress read-write
The IP net mask for this interface.
                     swL3IpCtrlVlanName 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.5 displaystring read-write
This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.
                     swL3IpCtrlMode 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.8 integer read-write
This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. dhcp(4) - The IP address will be set automatically from a DHCP server. Enumeration: 'dhcp': 4, 'other': 1, 'bootp': 3.
                     swL3IpCtrlAdminState 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.9 integer read-write
The state of the IP interface. Enumeration: 'disabled': 2, 'enabled': 1.
                     swL3IpCtrlIpv6LinkLocalAddress 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.14 ipv6address read-only
The IPv6 link local address for this interface.
                     swL3IpCtrlIpv6LinkLocalPrefixLen 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.15 integer read-only
The IPv6 prefix length for this IPv6 link local address.
                     swL3IpCtrlState 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.16 rowstatus read-only
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
                     swL3IpCtrlIpv6LinkLocalAutoState 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.17 integer read-write
The state of the IPv6 link local auto. Enumeration: 'disabled': 3, 'other': 1, 'enabled': 2.
                     swL3IpCtrlDhcpv6ClientState 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.20 integer read-write
The object indicates the state of the DHCPv6 client. Enumeration: 'disabled': 2, 'enabled': 1.
                     swL3IpCtrlIpDhcpOption12State 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.22 integer read-write
Enable or disable insertion of option 12 in the DHCPDISCOVER and DHCPREQUEST message. Enumeration: 'disabled': 2, 'enabled': 1.
                     swL3IpCtrlIpDhcpOption12HostName 1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.23 displaystring read-write
Specify the host name to be inserted in the DHCPDISCOVER and DHCPREQUEST message. The specified host name must start with a letter, end with a letter or digit, and have only letters, digits, and hyphen as interior characters; the maximal length is 63. By default, the host name is empty. When set an empty host name, means to clear the host name setting and use the default value to encode option 12.
             swL3Ipv6CtrlTable 1.3.6.1.4.1.171.11.101.3.3.2.1.4 no-access
This table contains IPv6 information of an IP interface.
                 swL3Ipv6CtrlEntry 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1 no-access
A list of IPv6 information about a specific IP interface.
                     swL3Ipv6CtrlInterfaceName 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.1 displaystring read-only
This object indicates the name of the IP interface.
                     swL3Ipv6CtrlMaxReassmblySize 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.2 integer read-only
Maximum Reassembly Size of the IP interface.
                     swL3Ipv6CtrlNsRetransTimer 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.3 unsigned32 read-write
Neighbor solicitation's retransmit timer. The unit is set in milliseconds.
                     swL3Ipv6CtrlRaState 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.5 integer read-write
Neighbor solicited state. Enumeration: 'disabled': 2, 'enabled': 1.
                     swL3Ipv6CtrlRaMinRtrAdvInterval 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.6 integer read-write
The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval. Default value: 0.33 * MaxRtrAdvInterval
                     swL3Ipv6CtrlRaMaxRtrAdvInterval 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.7 integer read-write
The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds.
                     swL3Ipv6CtrlRaLifeTime 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.8 integer read-write
Indicates the lifetime of the router as the default router.
                     swL3Ipv6CtrlRaReachableTime 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.9 integer read-write
Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation.
                     swL3Ipv6CtrlRaRetransTime 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.10 unsigned32 read-write
Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond.
                     swL3Ipv6CtrlRaHopLimit 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.11 integer read-write
Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message.
                     swL3Ipv6CtrlRaManagedFlag 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.12 integer read-write
When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration. Enumeration: 'disabled': 2, 'enabled': 1.
                     swL3Ipv6CtrlRaOtherConfigFlag 1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.13 integer read-write
When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information. Enumeration: 'disabled': 2, 'enabled': 1.
             swL3Ipv6AddressCtrlTable 1.3.6.1.4.1.171.11.101.3.3.2.1.5 no-access
This table contains IPv6 address information for each IP interface.
                 swL3Ipv6AddressCtrlEntry 1.3.6.1.4.1.171.11.101.3.3.2.1.5.1 no-access
A list of information about a specific IPv6 address.
                     swL3Ipv6AddressCtrlInterfaceName 1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.1 displaystring read-only
This object indicates the name of the IP interface.
                     swL3Ipv6Address 1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.2 ipv6address read-only
Specify the IPv6 address.
                     swL3Ipv6AddressCtrlPrefixLen 1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.3 integer read-only
Indicates the prefix length of this IPv6 address.
                     swL3Ipv6AddressCtrlPreferredLifeTime 1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.4 unsigned32 read-write
Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xffffffff.
                     swL3Ipv6AddressCtrlValidLifeTime 1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.5 unsigned32 read-write
Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff.
                     swL3Ipv6AddressCtrlOnLinkFlag 1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.6 integer read-write
When enabled, the address implied by the specified prefix is available on the link where the RA message is received. Enumeration: 'disabled': 2, 'enabled': 1.
                     swL3Ipv6AddressCtrlAutonomousFlag 1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.7 integer read-write
When enabled, the specified prefix will be used to create an autonomous address configuration. Enumeration: 'disabled': 2, 'enabled': 1.
                     swL3Ipv6AddressCtrlState 1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.8 rowstatus read-only
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
                     swL3Ipv6AddressCtrlAddressType 1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.9 integer read-only
This object indicates the type of the IPv6 address. manual(1): the IPv6 address is configured by user. dhcpv6(2): the IPv6 address is assigned by DHCPv6 server. stateless(3): the IPv6 address is assigned by router advertisement. Enumeration: 'stateless': 3, 'dhcpv6': 2, 'manual': 1.
             swL3IpCtrlAllIpIfState 1.3.6.1.4.1.171.11.101.3.3.2.1.7 integer read-write
This object indicates all interface function state of the device. Enumeration: 'disabled': 3, 'other': 1, 'enabled': 2.