DGS-1210-28PME-AX: View SNMP OID List / Download MIB

System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) V + - = .

Version number of the Hardware.

Version number of the Firmware.

This time interval is used to count the time and logout web interface automatically.

The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.

Group Interval is used to send D-link Discover packet to D-link SmartConsole Utility frequency. The timer in units of seconds. Set value 0 to disable group Interval.

This object is used to set Safeguard Enable\Disable. Enumeration: 'enable': 1, 'disable': 2.

This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'.

This object is used to save Configuration.

Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1522 bytes) of up to 10,000 bytes (tagged). Default jumbo frame is disabled. Enumeration: 'enable': 1, 'disable': 2.

A table to control the port specific parameters of the device like speed, duplex mode, etc.

An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.

Interface index of the port for the configuration in this entry applies.

This object indicates the port type: fiber 1G/100M or copper. Enumeration: 'copper': 1, 'fiber': 2.

Configures interface speed. Enumeration: 'rate100M-Half': 3, 'auto': 6, 'rate1000M-Full': 1, 'rate10G-Full': 8, 'rate10M-Full': 4, 'disable': 7, 'rate10M-Half': 5, 'rate100M-Full': 2.

The port's operating speed state. Enumeration: 'rate10M-Full': 5, 'rate100M-Half': 4, 'rate1000M-Full': 2, 'rate10G-Full': 7, 'down': 1, 'rate10M-Half': 6, 'rate100M-Full': 3.

Configures interface auto/mdi/mdix mode. The default setting is Auto. Enumeration: 'auto': 1, 'mdi': 2, 'mdix': 3.

Enables / disables flow control for the interface. Enumeration: 'enable': 1, 'disable': 2.

The link parner negotiate port's operating flow control state. Enumeration: 'disabled': 2, 'enabled': 1.

The port's media type. Enumeration: 'fiberwith100BaseSFPModule': 3, 'gigabitethernet': 2, 'fiberwith10GBaseSFPModule': 5, 'fiberwith1GBaseSFPModule': 4, 'fastethernet': 1.

The port's capability advertised. Bits: 'rate100-half': 2, 'rate1000-full': 5, 'rate10-full': 1, 'rate100-full': 3, 'rate10-half': 0, 'reserve': 4.

The port description table.

The port description entry.

This object indicates the port index.

This object indicates the port type: fiber 1G/100M or copper. Enumeration: 'copper': 1, 'fiber': 2.

This object indicates the port description.

This object indicates the port link up time.

The port error table.

A list of information for the err port of the device.

This object indicates the module's port number.(1..Max port number in the module)

This object decides whether the port state is enabled or disabled. Enumeration: 'disabled': 1, 'enabled': 2.

This object decides whether the PortStatus is err-disabled. Enumeration: 'other': 1, 'err-disabled': 2.

This object decides whether the PortStatus is LBD. Enumeration: 'lbd': 1.

This object indicates auto config is enabled or disabled. Enumeration: 'enable': 1, 'disable': 2.

This object is for Enabled(1) or Disabled(2) Web state in the system. Enumeration: 'disabled': 2, 'enabled': 1.

Web Server Port Number.

This object is for ARP aging time.

This object is for MAC aging time.

To set SerialPort baud-rate configuration. Enumeration: 'baudrate19200': 19200, 'baudrate38400': 38400, 'baudrate115200': 115200, 'baudrate9600': 9600.

To set SerialPort auto-logout-time configuration. Enumeration: 'logouttime10mins': 600, 'logouttime15mins': 900, 'logouttime2mins': 120, 'logouttime5mins': 300, 'logouttimenever': 0.

Enable/Disable management Telnetsetting mechanism. Enumeration: 'disabled': 2, 'enabled': 1.

The value is for setting telnet's UDP Port.

To set the WEB panel auto refresh timer. Enumeration: 'refreshtime1min': 3, 'refreshtime5mins': 4, 'refreshtime30secs': 2, 'refreshimenever': 0, 'refreshtime10secs': 1.

To set enable status for flood fdb. Enumeration: 'disabled': 2, 'enabled': 1.

To set system contact name.

To set dhcp auto config timeout.

To set enable status for CommandLogging. Enumeration: 'enable': 1, 'disable': 2.

To get the serial number.

The version of firmware information.

The size of firmware information.

The Update Time of firmware information.

The IP address of firmware information.

The user of firmware infomation.

The type of firmware infomation. Enumeration: 'web': 4, 'console': 1, 'ssh': 3, 'telnet': 2, 'unknown': -1.

This object indicates D-Link discover protocol is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates D-Link discover protocol report is enabled or disabled. This object only can be modified when D-Link discover protocol state is enabled. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates D-Link discover protocol report time period. This object only can be modified when both D-Link discover protocol state and D-Link discover protocol report state are enabled. Enumeration: 'time30seconds': 30, 'time60seconds': 60, 'time90seconds': 90, 'time120seconds': 120.

A table to control the port status of D-Link discover protocol.

An entry appears in this table for each port D-Link discover protocol status.

Interface index of the port for the configuration in this entry applies.

Configures the port status of D-Link discover protocol. Enumeration: 'disabled': 2, 'enabled': 1.

The Fan status for this device. Enumeration: 'failure': 0, 'normal': 1.

This object indicates auto image is enabled or disabled. Enumeration: 'enable': 1, 'disable': 2.

To get/set bootup config ID.

To get/set bootup Image.

Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system. Enumeration: 'dynamic': 2, 'manual': 1.

Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.

IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.

Gateway

Status of DHCP Option12 Enumeration: 'enable': 1, 'disable': 2.

Host name in DHCP option 12

Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system. Enumeration: 'dynamic': 2, 'manual': 1.

Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.

IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.

Gateway

Status of DHCP Option12 Enumeration: 'enable': 1, 'disable': 2.

Host name in DHCP option 12

The Description for the interface.

The vlan name for the interface.

The ID of VLAN that you want this interface to be in. It must be a exist vlan id. Enumeration: 'enable': 1, 'disable': 2.

The state of DHCPv6 that you want this interface to be in. It must be a exist vlan id. Enumeration: 'enable': 1, 'disable': 2.

The global state of link local that you want this interface to be in. It must be a exist vlan id. Enumeration: 'enable': 1, 'disable': 2.

The NS's retransmit time that you want this interface to be in. It must be a exist vlan id (1~3600).

The ipv6 default gateway that you want this interface to be in. It must be a exist vlan id.

A list of interface entries.

An entry containing management information applicable to a particular interface.

The index of this IPv6 entry.

The ip address of this IPv6 entry.

The ip prefix of this IPv6 entry.

The ip type of this IPv6 entry. Enumeration: 'unicast': 1, 'linklocal': 3, 'anycast': 2.

The status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available.

IProute Gateway of the system.

IProute Hops of the system.

The TFTP server's IP address is used to upload or download firmware.

Configure firmware filename to download.

The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName. Enumeration: 'download': 1, 'none': 0, 'upload': 2.

The tftp operation status represent firmware backup or upgrade status. Enumeration: 'fail': 2, 'transmit': 4, 'none': 0, 'progressing': 3, 'success': 1.

The TFTP server's IP address is used to upload or download configuration file.

The configuration filename is used to store or retrieve config from the tftp server.

The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName. Enumeration: 'download': 1, 'progressing': 3, 'upload': 2.

The tftp operation status represent configuration file backup or restore status. Enumeration: 'fail': 2, 'none': 0, 'progressing': 3, 'success': 1.

The TFTP server's IP address is used to upload or download firmware.

Type of IP interface. Enumeration: 'iPv4': 1, 'iPv6': 2.

Specifies the interface name when the tftpFwTargetServerIpAddress is linklocal address.

Configure firmware filename to download.

The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName. Enumeration: 'download': 1, 'none': 0, 'upload': 2.

The tftp operation status represent firmware backup or upgrade status. Enumeration: 'fail': 2, 'transmit': 4, 'none': 0, 'progressing': 3, 'success': 1.

The TFTP server's IP address is used to upload or download configuration file.

Type of IP interface. Enumeration: 'iPv4': 1, 'iPv6': 2.

Specifies the interface name when the tftpCfgTargetServerIpAddress is linklocal address.

The configuration filename is used to store or retrieve config from the tftp server.

The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName. Enumeration: 'download': 1, 'progressing': 3, 'upload': 2.

The tftp operation status represent configuration file backup or restore status. Enumeration: 'fail': 2, 'none': 0, 'progressing': 3, 'success': 1.

The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName. Enumeration: 'config1': 1, 'config2': 2.

Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing. Enumeration: 'reset': 1, 'noop': 2.

Resets the units statistics. A (1) resets the statistics count, a (2) does nothing. Enumeration: 'reset': 1, 'noop': 2.

This object is for enabling or disabling SNMP Community function. Enumeration: 'disabled': 2, 'enabled': 1.

A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.

A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. Enumeration: 'v2c': 2, 'v1': 1, 'v3': 3.

The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.

An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of UserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoAuthProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoAuthProtocol, then an 'inconsistentValue' error must be returned. If a set operation tries to set the value to the NoAuthProtocol while the UserPrivProtocol value in the same row is not equal to NoPrivProtocol, then an 'inconsistentValue' error must be returned. That means that an SNMP command generator application must first ensure that the UserPrivProtocol is set to the NoPrivProtocol value before it can set the UserAuthProtocol value to NoAuthProtocol. Enumeration: 'sha': 3, 'none': 1, 'md5': 2.

An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of usmUserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoPrivProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoPrivProtocol, then an 'inconsistentValue' error must be returned. Note that if any privacy protocol is used, then you must also use an authentication protocol. In other words, if usmUserPrivProtocol is set to anything else than NoPrivProtocol, then the corresponding instance of usmUserAuthProtocol cannot have a value of usmNoAuthProtocol. If it does, then an 'inconsistentValue' error must be returned. Enumeration: 'none': 1, 'des': 2.

The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified, except for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active.

The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.

In order to gain the access rights allowed by this conceptual row, this securityModel must be in use. Enumeration: 'v2c': 2, 'v1': 1, 'v3': 3.

The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If multiple entries are equally indexed except for this vacmAccessSecurityLevel index, then the entry which has the highest value for vacmAccessSecurityLevel is selected.

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.

The human readable name for a family of view subtrees.

The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees.

The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub-identifier of vacmViewTreeFamilySubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if, for each sub-identifier of the value of vacmViewTreeFamilySubtree, either: the i-th bit of vacmViewTreeFamilyMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of vacmViewTreeFamilySubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of vacmViewTreeFamilySubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of vacmViewTreeFamilySubtree. Note that masks of length greater than zero length do not need to be supported. In this case this object is made read-only.

Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or excluded from the MIB view. Enumeration: 'included': 1, 'excluded': 2.

The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.

The unique index value of a row in this table.

A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format.

The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpCommunityName and snmpCommunitySecurityName objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpCommunityStatus is active(1).

This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.

The locally arbitrary.

The Level of Security to be used when generating SNMP messages using this entry. Enumeration: 'v2c': 2, 'v1': 1, 'v3NoAuthNoPriv': 3, 'v3AuthNoPriv': 4, 'v3AuthPriv': 5.

This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.

Type of IP interface. Enumeration: 'iPv4': 1, 'iPv6': 2.

The locally arbitrary.

The Level of Security to be used when generating SNMP messages using this entry. Enumeration: 'v2c': 2, 'v1': 1, 'v3NoAuthNoPriv': 3, 'v3AuthNoPriv': 4, 'v3AuthPriv': 5.

Specifies the interface name when the syslogSrvIP is linklocal address.

An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the value of the snmpEngineID of a remote SNMP engine with which this user can communicate.

This object is for enabling or disabling SNMP login fail event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling devie Bootup event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling devie Bootup event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling Copper link up / link down event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling RSTP topology change event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling Firmware upgrade suess or fail event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling PoE power on /off event in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling PoE power error event in the system. There are four(short circuit, over load, power denied, and thermal shutdown) error types in this event. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling PoE over max power budget event in the system. Enumeration: 'disabled': 2, 'enabled': 1.

Used to configure trap settings for BPDU attack protection events. Enumeration: 'attackDetected': 2, 'both': 4, 'none': 1, 'attackCleared': 3.

Enumeration: 'disabled': 2, 'enabled': 1.

Enumeration: 'disabled': 2, 'enabled': 1.

Enumeration: 'disabled': 2, 'enabled': 1.

Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling send gratuitous trap when IP address conflicted in the network. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling community encryption. Enumeration: 'disabled': 2, 'enabled': 1.

The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start. Enumeration: 'disabled': 2, 'enabled': 1.

The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w and 'mstp(3)' indicates the Multiple Spanning Tree Protocol Specified in IEEE 802.1s. Enumeration: 'mstp': 3, 'stp': 1, 'rstp': 2.

The Value of the writable portion of the Bridge Identifier comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.

The value used by the Port Transmit state machine to limit the maximum transmission rate.

The value that all bridges use for MaxAge when this bridge is acting as the root. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.

The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D specifies that the range for this parameter is related to the value of BridgeMaxAge. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

This object is for enabling or disabling forward BPDU. Enumeration: 'disabled': 2, 'enabled': 1.

The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Root Identifier parameter in all Configuration Bridge PDUs originated by this node.

The Cost of the path to the CIST Root as seen from this bridge.

The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.

This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in a particular state before moving to the next state.

The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge.

This object is for enabling or disabling topology change event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling new root event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

The MAC address used by this bridge when it must be referred to in a unique fashion.

The bridge identifier of the old root of the spanning tree instance as determined by the Spanning Tree Protocol as executed by this node.

MSTI Regional Root Identifier value for the Instance.

A table that contains port-specific information for the Spanning Tree Protocol.

A list of information maintained by every port about the Spanning Tree Protocol state for that port.

The Port number of the port for which this entry contains spanning tree information.

Current state of the Port which can be changed to either Disabled or Enabled for ALL spanning tree instances. Setting this object will override the port's status in any of the MSTI contexts Enumeration: 'disabled': 0, 'enabled': 1.

The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting the CistPortPriority value. The values that are set for Port Priority must be in steps of 16.

The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object stpPortPathCost. If the default Path Cost is being used,this object returns '0' when read.

The contribution of this port to the path cost of paths towards the CIST Root which include this port.

Indicates the Protocol migration state of this Port. When operating in RSTP/MSTP (version >= 2) mode, writing TRUE(1) to this object forces this port to transmit MSTP BPDUs without instance information. Any other operation on this object has no effect and it always returns FALSE(2) when read.

This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled. Enumeration: 'false': 0, 'true': 1, 'auto': 2.

The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means. Enumeration: 'forceFalse': 1, 'forceTrue': 0, 'auto': 2.

A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'.

A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC-Operational for the attached LANs transitions frequently.

The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.

Current state of the Port as defined by the Common spanning tree protocol. Enumeration: 'disabled': 1, 'discarding': 2, 'forwarding': 5, 'learning': 4.

This object is for enabling or disabling forward BPDU. Enumeration: 'disabled': 2, 'enabled': 1.

The Name for the Region's configuration. By Default Region Name will be equal to the Bridge Mac Address.

Version of the MST Region.

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

This table contains one entry for each instance of MSTP. This table maintains context ID as one more index to support Multiple Instances.

A conceptual row containing the status of the MSTP instance.

An arbitrary integer within the range from 1 to the value of Max Instance Number that uniquely identifies an instance.

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values.

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to unmap from this Instance. A vlan may not be unmapped from this instance if it is not already mapped to this Instance. This object is used only for SET operation.GET Operation returns null values.

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.

The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start. Enumeration: 'disabled': 2, 'enabled': 1.

Table containing Bridge Information specific to Spanning Tree Instance. This table maintains context ID as one more index to support Multiple Instances.

Entry indicating the Bridge Information.

Spanning Tree Instance to which the information belongs.

The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.

The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start. Enumeration: 'disabled': 2, 'enabled': 1.

This table contains Common Spanning Tree Port Information.

A list of information maintained by every port for Common Spanning tree.

The Port number of the port for which this entry contains spanning tree information.

The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.

Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port Enumeration: 'disabled': 0, 'enabled': 1.

Current Port Role of the port for this spanning tree instance. Enumeration: 'backup': 2, 'alternate': 1, 'designated': 4, 'disabled': 0, 'master': 5, 'root': 3.

This table contains Spanning Tree Instance Specific Port Information.

A list of information maintained by every port for each and every spanning tree instance.

The Port number of the port for which this entry contains spanning tree information.

The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.

Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port Enumeration: 'disabled': 0, 'enabled': 1.

Current Port Role of the port for this spanning tree instance. Enumeration: 'backup': 2, 'alternate': 1, 'designated': 4, 'disabled': 0, 'master': 5, 'root': 3.

Enable/Disable management VLAN mechanism. Enumeration: 'disabled': 2, 'enabled': 1.

The management VLAN ID, which will allow to forward packets of that VLAN to CPU.

Enable/Disable IEEE 802.1Q Asymmetric VLAN Enumeration: 'disabled': 2, 'enabled': 1.

A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.

Information for a VLAN configured into the device by (local or network) management.

An administratively assigned string, which may be used to identify the VLAN.

The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed.

The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port per-VLAN Registrar control for Registration Forbidden for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanEgressPorts. The default value of this object is a string of zeros of appropriate length, excluding all ports from the forbidden set.

The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option.

Enable/Disable Advertisement Status of the IEEE 802.1Q VLAN. Enumeration: 'disabled': 2, 'enabled': 1.

The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard.

This table contains the list of ports through which a router, in a particular VLAN is reachable.

A list of multicast filter mode information for each VLAN ID.

Per Vlan to configure multicast filtering function.

Filter unknown multicast frames or normal operation(i.e. forwarding) Enumeration: 'filter': 1, 'forward': 0, 'forwardall': 2.

Enable/Disable VLAN PVID auto assignment Enumeration: 'disabled': 2, 'enabled': 1.

Sets the Link Aggregation Module administrative status as enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel.

There is one entry in this table for each created port-channel port.

The index of the port-channel(Aggregator's interface index).

Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel.

Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled.

The master port of the port-channel.

Sets the Link Aggregation load balance algorithm. Enumeration: 'sourceMAC': 1, 'destMAC': 2, 'sourceAndDestMAC': 3, 'destIP': 5, 'sourceIP': 4, 'sourceAndDestIP': 6.

A table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table for each physical port.

A list of Link Aggregation Control configuration parameters for each Aggregation Port on this device.

The index of the port.

The priority value assigned to this Aggregation Port. This 16-bit value is read-write.

This object indicates LACP-Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and partner are both in passive mode, they do not exchange LACP packets. Enumeration: 'active': 1, 'passive': 2.

This object indicates LACP-Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds. Enumeration: 'short': 1, 'long': 2.

Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning. Enumeration: 'on': 1, 'off': 2.

The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet value set up as '# 0x0F 0xFF 0xFF 0xFF' means from port 1 to port 4 are not in auto learning state, the other ports are in auto learning state. It can be set up when Disable Auto Learning is enable.

A list of the Static MACs

A Static MAC entry containing the mac and forwarding port.

The VLAN ID of the static MAC entry.

The MAC address associated of the static MAC entry.

The forwarding port of the static MAC entry.

The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC.

Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops performing protocol operations. Enumeration: 'disabled': 2, 'enabled': 1.

This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.

This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.

The maximum data driven learning entry value.

Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module forwards packets to report to all port. When set to 'disabled', the IGS module forwards packets to router port only. Enumeration: 'disabled': 2, 'enabled': 1.

This table contains the list of ports through which a router, in a particular VLAN is reachable.

Contains the VLAN ID and list of ports on which routers are present in the VLAN.

VLAN ID of the ports through which router is reachable.

List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.

This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system.

Contains snooping status , version and fast leave configuration for a specific VLAN.

Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done.

This object allows you to enable/disable IGS function on a specific VLAN. Enumeration: 'disabled': 2, 'enabled': 1.

Indicates whether the switch is configured as a querier in the VLAN Enumeration: 'disabled': 2, 'enabled': 1.

The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries. Enumeration: 'disabled': 2, 'enabled': 1.

This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network.

List of ports which are configured statically as router ports

List of ports which can be configured statically as forbidden router ports.

Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table. Enumeration: 'disabled': 2, 'enabled': 1.

This object allows you to enable/disable Data Driven Learning function on a specific VLAN. Enumeration: 'disabled': 2, 'enabled': 1.

This object allows you to enable/disable Querier Version function on a specific VLAN. Enumeration: 'igmp-v1': 1, 'igmp-v3': 3, 'igmp-v2': 2.

This object allows you to enable/disable Data Driven Learning Age Out State on a specific VLAN. Enumeration: 'disabled': 2, 'enabled': 1.

Enables or disables Report suppression in the system. Enumeration: 'disabled': 2, 'enabled': 1.

When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'igsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.

The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'igsRobustnessValue' queries before removing the port from the group membership information in the forwarding database.

The maximum query response time advertised in IGMPv2 general queries on this interface.

This table contains MAC based multicast forwarding information.

This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded.

VLAN ID pertaining to the Multicast forwarding entry

Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.

Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.

List of ports onto which the multicast data packets destined for this group will be forwarded.

This table is used to manage the IGMP Authentication function of the switch.

Contains management entities for IGMP Authentication function.

The port index of igsAccessAuthTable which indicates the port to be configured.

This object can be configured to set IGMP Authentication state to enabled/disabled on each port. Enumeration: 'disabled': 2, 'enabled': 1.

This table is used to manage the IGMP Host based Fast Leave function of the switch.

Contains management entities for IGMP Host based fast leave function.

VLAN ID of Host table entry.

Group address of Host table entry.

Port number of Host table entry.

Host IP address of Group in Host table entry.

Enable/Disable GVRP mechanism. Enumeration: 'disabled': 2, 'enabled': 1.

The Join Time value assigned to this Join Time field. This 16-bit value is read-write.

The Leave Time value assigned to this Leave Time field. This 16-bit value is read-write.

The Leave-All Time value assigned to this Leave-All Time field. This 16-bit value is read-write.

A table containing static configuration information for each GVRP configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.

Information for a GVRP configured into the device by (local or network) management.

The index of the port.

The PVID value assigned to this Aggregation Port. This 16-bit value is read-write.

Enable/Disable GVRP State to this Aggregation Port. Enumeration: 'disabled': 2, 'enabled': 1.

Enable/Disable Ingress Checking mechanism of GVRP to this Aggregation Port. Enumeration: 'disabled': 2, 'enabled': 1.

Chose types All Frames/Tagged to this Aggregation Port. Enumeration: 'taggedOnly': 2, 'allFrames': 1.

Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues. Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8 for WS3 spec. Queues with higher weights get bandwidth before than other queues with less weights. Enumeration: 'wrr': 2, 'strictPriority': 1.

A list of cosOutputSchedule.

A list of cosOutputClass Weight.

A index of class 0 ~ 7.

cos weight

A list of 802.1p port default priority Entries.

A list of 802.1p port default priority priorities.

A port identifier that is in the range of 1 to ifNumber.

For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled. Enumeration: 'priority1': 1, 'priority0': 0, 'priority3': 3, 'priority2': 2, 'priority5': 5, 'priority4': 4, 'priority7': 7, 'priority6': 6.

For ingress untagged packets, the per port 'Effective Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled. Enumeration: 'priority1': 1, 'priority0': 0, 'priority3': 3, 'priority2': 2, 'priority5': 5, 'priority4': 4, 'priority7': 7, 'priority6': 6.

A table mapping evaluated User Priority to Traffic Class, for forwarding by the bridge. Traffic class is a number in the range (0..3).

User Priority to Traffic Class mapping.

For ingress tagged packets, D-Link Smart Switches will refer to these information and prioritize them with 4 different priority queues. If 802.1p is enabled.

The User Class the received frame is mapped to.

Settings of Qos mode: DSCP QoS or TOS Qos. IEEE 802.1p : It specifies a priority(0~7) value to four queues in WS3 : Low(1,2), Medium(0,3), High(4,5) and Highest(6,7), inclusive that can be used by Quality of Service (QoS) disciplines to differentiate traffic. DSCP : Differentiated services enhancements to the Internet protocol are intended to enable scalable service discrimination in the Internet without the need for per-flow state and signaling at every hop. Enumeration: 'tos': 1, 'dscp': 2.

DiffServ Type 0 : IP ToS value = 0

DiffServ Type 01 : IP ToS value = 4

DiffServ Type 02 : IP ToS value = 8

DiffServ Type 03 : IP ToS value = 12

DiffServ Type 04 : IP ToS value = 16

DiffServ Type 05 : IP ToS value = 20

DiffServ Type 06 : IP ToS value = 24

DiffServ Type 07 : IP ToS value = 28

DiffServ Type 08 : IP ToS value = 32

DiffServ Type 09 : IP ToS value = 36

DiffServ Type 10 : IP ToS value = 40

DiffServ Type 11 : IP ToS value = 44

DiffServ Type 12 : IP ToS value = 48

DiffServ Type 13 : IP ToS value = 52

DiffServ Type 14 : IP ToS value = 56

DiffServ Type 15 : IP ToS value = 60

DiffServ Type 16 : IP ToS value = 64

DiffServ Type 17 : IP ToS value = 68

DiffServ Type 18 : IP ToS value = 72

DiffServ Type 19 : IP ToS value = 76

DiffServ Type 20 : IP ToS value = 80

DiffServ Type 21 : IP ToS value = 84

DiffServ Type 22 : IP ToS value = 88

DiffServ Type 23 : IP ToS value = 92

DiffServ Type 24 : IP ToS value = 96

DiffServ Type 25 : IP ToS value = 100

DiffServ Type 26 : IP ToS value = 104

DiffServ Type 27 : IP ToS value = 108

DiffServ Type 28 : IP ToS value = 112

DiffServ Type 29 : IP ToS value = 116

DiffServ Type 30 : IP ToS value = 120

DiffServ Type 31 : IP ToS value = 124

DiffServ Type 32 : IP ToS value = 128

DiffServ Type 33 : IP ToS value = 132

DiffServ Type 34 : IP ToS value = 136

DiffServ Type 35 : IP ToS value = 140

DiffServ Type 36 : IP ToS value = 144

DiffServ Type 37 : IP ToS value = 148

DiffServ Type 38 : IP ToS value = 152

DiffServ Type 39 : IP ToS value = 156

DiffServ Type 40 : IP ToS value = 160

DiffServ Type 41 : IP ToS value = 164

DiffServ Type 42 : IP ToS value = 168

DiffServ Type 43 : IP ToS value = 172

DiffServ Type 44 : IP ToS value = 176

DiffServ Type 45 : IP ToS value = 180

DiffServ Type 46 : IP ToS value = 184

DiffServ Type 47 : IP ToS value = 188

DiffServ Type 48 : IP ToS value = 192

DiffServ Type 49 : IP ToS value = 196

DiffServ Type 50 : IP ToS value = 200

DiffServ Type 51 : IP ToS value = 204

DiffServ Type 52 : IP ToS value = 208

DiffServ Type 53 : IP ToS value = 212

DiffServ Type 54 : IP ToS value = 216

DiffServ Type 55 : IP ToS value = 220

DiffServ Type 56 : IP ToS value = 224

DiffServ Type 57 : IP ToS value = 228

DiffServ Type 58 : IP ToS value = 232

DiffServ Type 59 : IP ToS value = 236

DiffServ Type 60 : IP ToS value = 240

DiffServ Type 61 : IP ToS value = 244

DiffServ Type 62 : IP ToS value = 248

DiffServ Type 63 : IP ToS value = 252

TOS 0

TOS 01

TOS 02

TOS 03

TOS 04

TOS 05

TOS 06

TOS 07

A list of port priority settings.

A list of port priority settings Entries.

A port identifier that is in the range of 1 to ifNumber.

The port priority setting type. (ex. none = 0, 802.1p = 2, DSCP = 4. If you want enable 802.1p & DSCP, the value is 2 + 4 = 6. Enumeration: 'none': 0, 'dscp-tos': 4, 'ieee8021P': 2, 'ieee8021P-dscp-tos': 6.

A list of priority by acl setting.

A list of priority by acl setting entry.

Index of priority by acl setting.

Type of priority by acl setting. Enumeration: 'udp': 3, 'protocol': 5, 'ip': 1, 'tcp': 2, 'mac': 0, 'vlanid': 4.

Dst MAC of priority by acl setting.

Dst IP of priority by acl setting

Dst TCP/UDP port of priority by acl setting

VLAN ID of priority by acl setting

Ip protocol number of priority by acl setting

Be mapped class of priority by acl setting. Enumeration: 'class2': 2, 'class3': 3, 'class0': 0, 'class1': 1.

Status of priority by acl setting.

A list of priority by acl setting.

A list of priority by acl setting entry.

Index of priority by acl setting.

Type of priority by acl setting. Enumeration: 'udp': 3, 'protocol': 5, 'ip': 1, 'tcp': 2, 'mac': 0, 'vlanid': 4, 'ipv6': 6, 'ipv6traffic-class': 7.

Dst MAC of priority by acl setting.

Dst IP of priority by acl setting

Dst IP of priority by acl setting.

Dst TCP/UDP port of priority by acl setting

VLAN ID of priority by acl setting

Ip protocol number of priority by acl setting

Ipv6 Traffic Class number of priority by acl setting

Be mapped class of priority by acl setting. Enumeration: 'class2': 2, 'class3': 3, 'class0': 0, 'class1': 1.

Status of priority by acl setting.

A list of cosBandwidthCtrlEntry default priority Entries.

A list of cosBandwidthCtrlEntry default priority priorities.

A port identifier that is in the range of 1 to ifNumber.

A BandwidthCtrlClassIndex identifier that is in the range of 1 to ifNumber.

The BandwidthValue return value.

A table to control the rate limiting parameters either for the entire switch or for each interface in the switch.

An entry appears in this table for each physical interface in the switch.

The interface index for which the configuration in this entry applies.

Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000 (Kbits per second) in GE port.

Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port.

The trap setting of traffic control. Enumeration: 'stormCleared': 2, 'none': 0, 'both': 3, 'stormOccurred': 1.

The traffic control table.

The traffic control entry.

The traffic control index.

The action mode of traffic control. Enumeration: 'drop': 0, 'shutdown': 1.

The control type of traffic control. (b: Broadcast, m: Multicast, u: Unknown Unicast) Enumeration: 'none': 0, 'b': 1, 'mb': 3, 'm': 2, 'um': 6, '': 4, 'umb': 7, 'ub': 5.

The threshold of traffic control.

The count down value of traffic control.

The time interval of traffic control.

This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection. Enumeration: 'disabled': 2, 'enabled': 1.

A table to configure trusted host in the system.

Each entry in this table represents rules for particular trusted host.

The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.

Used to mask with IP address, it allow you set a subnet as a trusted host entry.

The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.

A table to configure trusted host for in the system.

Each entry in this table represents rules for particular trusted host.

Type of IP interface. Enumeration: 'iPv4': 1, 'iPv6': 2.

The IP address of host you allow to access to D-Link Smart Switch. Your local host IPv4/6 Addresses must be one of the IP Addresses to avoid disconnection.

Used to mask with IPv4/6 address, it allow you set a subnet as a trusted host entry.

The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.

A table to control port security features of the device.

An entry appears in port security table for each interface in the system.

The interface index for which the configuration in this entry applies.

Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled. Enumeration: 'disabled': 2, 'enabled': 1.

Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 64. Note: Set value 0 means cannot learn MAC address.

Configures port security lock address mode for the interface. deleteOnReset : The locked addresses will not age out until the Switch has been reset. deleteOnTimeout : The locked addresses will age out after the aging timer expires. Permanent : The locked addresses will not age out after the aging timer expires. Enumeration: 'permanent': 3, 'deleteOnTimeout': 2, 'deleteOnReset': 1.

A table to control port security FDB Permanent of the device.

An entry appears in port security table for each interface in the system.

The index of the port security MAC entry.

The VLAN ID of the port security MAC entry.

The MAC address associated of the port security MAC entry.

The forwarding port of the port security MAC entry.

A table to control ARP Spoofing prevention for the entire switch or for each interface in the switch.

An entry appears in this table for each interface in the system.

Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.

Ethernet Mac Address.

Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.

This object indicates the status of this entry.

This object is for enabling or disabling secure HTTP in the system. Enumeration: 'enable': 1, 'disable': 2.

This object is to configure the cipher-suites list. Bits: 'rsa-null-md5': 0, 'dh-rsa-3des-sha': 5, 'rsa-3des-sha': 3, 'dh-rsa-des-sha': 4, 'rsa-des-sha': 2, 'rsa-exp1024-des-sha': 6, 'rsa-null-sha': 1.

To enable or disable DHCP Server Screening port list.

To enable or disable DHCP Server Screening vlan list.

DSS Trap Log Suppress Duration. Enumeration: 'one-min': 1, 'thirty-min': 30, 'five-min': 5.

A table to control filter DHCP Server for the entire switch or for each interface in the switch.

An entry appears in this table for each interface in the system.

Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.

Ethernet Mac Address.

Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.

Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.

This object indicates the status of this entry.

This object is for enabling or disabling ssh in the system. Enumeration: 'enable': 1, 'disable': 2.

This object indicates the max auth fail retry attempt times.

This object indicates one SSH session rekey time interval. Enumeration: 'ten-min': 1, 'never': 0, 'sixty-min': 3, 'thirty-min': 2.

This object indicates max SSH session number supported in system.

This object indicates SSH connection timeout value.

The object indicates authen method password is enabled or disabled. Enumeration: 'enable': 1, 'disable': 2.

The object indicates authen method public-key is enabled or disabled. Enumeration: 'enable': 1, 'disable': 2.

The object indicates authen method host-key is enabled or disabled. Enumeration: 'enable': 1, 'disable': 2.

This object is to configure the cipher-suites list. Bits: 'tripleDESCBC': 0.

This object is to configure the MAC-list. Bits: 'hMAC-SHA1': 0, 'hMAC-MD5': 1.

The object indicates Public key generating algorithm RSA is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

A table to configure SSH user auth in the system.

An entry to configure user auth in the system.

The Schedule identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 8.

The ssh user name associated with the SSH suer Info. entry (e.g., `admin, user').

The object indicates which auth used by the user. Enumeration: 'publickey': 4, 'hostbased': 1, 'password': 2.

The ssh host name associated with the SSH suer Info. entry (e.g., `DUT1, DUT2').

SSH HostBased IP Address of the system.

A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel

There is one entry in this table for each created port-channel port

The ifIndex of the port-channel(Aggregator's interface index).

Port list of port channel.

A table to control IP-MAC-Port Binding Setting features of the device.

An entry appears in IP-MAC-Port Binding Setting table for each interface in the system.

Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.

Disable / enable IP-MAC-Port Binding admin state for the interface. Enumeration: 'disabled': 0, 'enabled': 1.

Disable / enable IP-MAC-Port Binding DHCP snooping state for the interface. Enumeration: 'disabled': 0, 'enabled': 1.

Set IP-MAC-Port Binding ARP Inspection state for the interface. Enumeration: 'disabled': 0, 'strict': 1, 'loose': 2.

Set IP-MAC-Port Binding IP Inspection state for the interface. Enumeration: 'disabled': 0, 'enabled': 1.

Disable / enable IP-MAC-Port Binding Allow-Zero-IP state for the interface. Enumeration: 'disabled': 0, 'enabled': 1.

Disable / enable IP-MAC-Port Binding Forward-DHCP-Packet state for the interface. Enumeration: 'disabled': 0, 'enabled': 1.

Set the maximum number of IPv4 entries that can be learned for the interface.

Set the maximum number of IPv6 entries that can be learned for the interface.

Set IP-MAC-Port Binding ND Inspection state for the interface. Enumeration: 'disabled': 0, 'enabled': 1.

Set IP-MAC-Port Binding protocol state for the interface. Enumeration: 'all': 2, 'ipv4': 0, 'ipv6': 1.

A table to control auto scan features of the device.

An entry appears in auto scan table for each interface in the system.

The MAC address associated of the auto scan entry.

The port number of the auto scan entry.

The IP address associated of the auto scan entry.

The VLAN ID of the auto scan entry.

Disable / enable IP-MAC-Port Binding for the entry. Enumeration: 'disabled': 0, 'enabled': 1.

A table to control Manual IP-MAC-Port Binding white list features of the device.

An entry appears in Manual IP-MAC-Port Binding white list table for each interface in the system.

The IP address associated of the Manual IP-MAC-PORT Binding white list entry.

The MAC address associated of the Manual IP-MAC-PORT Binding white list entry.

The port number of the Manual IP-MAC-PORT Binding white list entry.

The status of a row in impbBindingListTable. By setting this object, new entries can be created in impbBindingListTable and existing entries can be removed from impbBindingListTable. It can be used as specified in the SNMP v2 standard.

A table to control IP-MAC-Port Binding black list of the device.

An entry appears in Manual IP-MAC-Port Binding black list table for each interface in the system.

The MAC address associated of the IP-MAC-PORT Binding black list entry.

The VLAN ID of the IP-MAC-PORT Binding black list entry.

The port number of the IP-MAC-PORT Binding black list entry.

The IP address associated of the IP-MAC-PORT Binding black list entry.

nothing/delete IP-MAC-Port Binding for the interface. Enumeration: 'nothing': 0, 'deleted': 1.

The begin for IP address associated of the IP-MAC-PORT Binding auto scan entry.

The end for IP address associated of the IP-MAC-PORT Binding auto scan entry.

Nothing / scan IP-MAC-Port Binding auto scan for the interface. Enumeration: 'nothing': 0, 'scan': 1.

A table to display DHCP snooping entries of the device.

An entry appears in DHCP snooping table for each interface in the system.

The MAC address associated of the DHCP snooping entry.

The IP address associated of the DHCP snooping entry.

The lease time associated of the DHCP snooping entry.

The port number associated of the DHCP snooping entry.

Disable / enable IP-MAC-Port Binding roaming state. Enumeration: 'disabled': 0, 'enabled': 1.

Disable / enable IP-MAC-Port Binding vlan mode state. Enumeration: 'disabled': 0, 'enabled': 1.

IP-MAC-Port Binding vlan mode VID list.

Configure IP-MAC-Port Binding log state. Enumeration: 'disabled': 0, 'all': 3, 'ipv4': 1, 'ipv6': 2.

Configure DHCPv6 PD snooping state. Enumeration: 'disabled': 0, 'enabled': 1.

This object is for enabling or disabling topology change event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

The object is for IMPB trap sign in the system.

Show Auto scan status Enumeration: 'scanning': 1, 'stop': 0.

This object indicates the Access Authentication is enable or disable. Enumeration: 'disabled': 2, 'enabled': 1.

Timeout in second for login authentication response.

The amount for login authentication, if login failure exceed, connection or access would be locked.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP.

A table that contains informations about server group.

A list of the group including servers.

A value that uniquely identifies this SwAACServerGroupEntry .

A human-readable text string of the method group. The name is writable only if Group is new created, which the value of aacServerGroupRowStatus is 'notReady'.

The list of servers in the group, each bit indicates a specified server ID. The server must be created before including it. Bits: 'id8': 7, 'id9': 8, 'id6': 5, 'id7': 6, 'id4': 3, 'id5': 4, 'id2': 1, 'id3': 2, 'id1': 0, 'id10': 9, 'id11': 10, 'id12': 11, 'id13': 12, 'id14': 13, 'id15': 14, 'id16': 15.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table that contains information about severs.

A list of the information of server .

A value that uniquely identifies this SwAACServerGroupEntry.

The IP address of Server

The authentication protocol provided by the Server. Enumeration: 'radius': 2, 'tacacsPlus': 1.

The TCP/IP port .

The key used while authentication process.

Server response timeout .

Client retry count . (-1: No retry mechanism)

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table that contains information about severs.

A list of the information of server .

A value that uniquely identifies this SwAACServerGroupEntry.

The IP address of the AAC server IP type referred to in this table entry. (IPv4=1, IPv6=2)

The IP address of Server

Specifies the interface name when the aacServerIPAddr is linklocal address.

The authentication protocol provided by the Server. Enumeration: 'radius': 2, 'tacacsPlus': 1.

The TCP/IP port .

The key used while authentication process.

Server response timeout .

Client retry count . (-1: No retry mechanism)

The accounting port .

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table that contains information about Login authentication method lists.

A list of the Authentication methods.

A value that identifies this method list.

A human-readable text string of the method list.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table that contains information about Enable authentication method lists.

A list of the Authentication methods.

A value that identifies this method list.

A human-readable text string of the method list.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

This object is used to set Local Enable Password.

A table that contains information about Accounting authentication method lists.

A list of the Authentication methods.

A value that identifies this method list.

A human-readable text string of the method list.

The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'local': 0, 'tacacsPlus': 1.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

This object indicates aac Accounting Service Network is radius-only, default-method-list, method-list-name and disable about Accounting Service Network. Enumeration: 'method-list-name': 2, 'disabled': -1, 'radius-only': 0, 'default-method-list': 1.

This object indicates aac Accounting Service Shell is radius-only, default-method-list, method-list-name and disable about Accounting Service Network. Enumeration: 'method-list-name': 2, 'disabled': -1, 'radius-only': 0, 'default-method-list': 1.

This object indicates aac Accounting System Shell is radius-only, default-method-list, method-list-name and disable about Accounting Service Network. Enumeration: 'method-list-name': 2, 'disabled': -1, 'radius-only': 0, 'default-method-list': 1.

This object indicates which method list Accounting Admin Command Service uses. If the value is -1, it means disabled.

This object indicates which method list Accounting Operator Command Service uses. If the value is -1, it means disabled.

This object indicates which method list Accounting PowerUser Command Service uses. If the value is -1, it means disabled.

This object indicates which method list Accounting User Command Service uses. If the value is -1, it means disabled.

This object is used to configure server password encryption status. Enumeration: 'disabled': 2, 'enabled': 1.

A table to ACL profile .

Each entry in this table is a ACL profile. Index to the table is ACL profile ID.

The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.

The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, arpSP-permit(4) - for ARP Spoofing prevention entry, arpSP-deny(5) - for ARP Spoofing prevention entry, voiceVlan(6) - for Voice VLAN OUI entry. userDefined(9) - for User Defined entry. Note that only l2, l3 and userDefined could be set by user, other is reserved for system to show information. Enumeration: 'aclQos': 8, 'arpSP-deny': 5, 'userDefined': 9, 'impb': 3, 'l2': 1, 'l3': 2, 'arpSP-permit': 4.

The number of rules in this profile.

Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST-MAC 0 (LSB) L2 SRC-MAC 1 L2 VID 2 L2 8021P-PRIORITY 3 L2 ETHER-TYPE 4 L3 DSCP 5 L3 ICMP-TYPE 6 L3 ICMP-CODE 7 L3 IGMP-TYPE 8 L3 DST-IP 9 L3 SRC-IP 10 L3 DST-PORT 11 L3 SRC-PORT 12 L3 TCPFLAG 13 ARP-SP ARP-SENDER-MAC 14 ARP-SP ARP-SENDER-IP 15 L3 TOS 16 UDF UDF1 17 UDF UDF2 18 UDF UDF3 19 UDF UDF4 20 L3v6 TRAFFIC-CLASS 21 L3v6 DST-IPV6 22 L3v6 SRC-IPV6 23 (MSB) ------------------------------------------- The value is in Hex format.

The ACL Profile destination MAC address mask. If DST-MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care.

The ACL Profile source MAC address mask. If SRC-MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.

Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. Enumeration: 'none': 0, 'ipProtocolMask': 256, 'udp': 17, 'tcp': 6, 'icmpv6': 58, 'icmp': 1, 'igmp': 2.

The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.

The ACL Profile destination IP address mask. If DST-IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'

The ACL Profile source IP address mask. If SRC-IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'

The ACL Profile UDP/TCP destination port mask. If DST-PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.

The ACL Profile UDP/TCP source port mask. If SRC-PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.

The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.

The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.

Indicate which Udf field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ UDF Offset1 0 (LSB) UDF Offset2 1 UDF Offset3 2 UDF Offset4 3 ------------------------------------------- The value is in Hex format.

The value of offset Chunk.

The value of offset MAsk.

The value of offset Chunk.

The value of offset MAsk.

The value of offset Chunk.

The value of offset MAsk.

The value of offset Chunk.

The value of offset MAsk.

This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted.

A table to ACL profile .

Each entry in this table is a ACL profile. Index to the table is ACL profile ID.

The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.

The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3v4 (2) - for IPv4-based rule, l3v6 (11) - for IPv6-based rule, arpSP-permit(4) - for ARP Spoofing prevention entry, arpSP-deny(5) - for ARP Spoofing prevention entry, voiceVlan(6) - for Voice VLAN OUI entry. userDefined(9) - for User Defined entry. Note that only l2, l3 and userDefined could be set by user, other is reserved for system to show information. Enumeration: 'aclQos': 8, 'arpSP-deny': 5, 'l3v4': 2, 'l3v6': 11, 'impb': 3, 'l2': 1, 'arpSP-permit': 4, 'userDefined': 9.

The number of rules in this profile.

Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST-MAC 0 (LSB) L2 SRC-MAC 1 L2 VID 2 L2 8021P-PRIORITY 3 L2 ETHER-TYPE 4 L3 DSCP 5 L3 ICMP-TYPE 6 L3 ICMP-CODE 7 L3 IGMP-TYPE 8 L3 DST-IP 9 L3 SRC-IP 10 L3 DST-PORT 11 L3 SRC-PORT 12 L3 TCPFLAG 13 ARP-SP ARP-SENDER-MAC 14 ARP-SP ARP-SENDER-IP 15 L3 TRAFFIC-CLASS 21 L3 TOS 16 UDF UDF1 17 UDF UDF2 18 UDF UDF3 19 UDF UDF4 20 L3v6 TRAFFIC-CLASS 21 L3v6 DST-IPV6 22 L3v6 SRC-IPV6 23 (MSB) ------------------------------------------- The value is in Hex format.

The ACL Profile destination MAC address mask. If DST-MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care.

The ACL Profile source MAC address mask. If SRC-MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.

Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. Enumeration: 'none': 0, 'ipProtocolMask': 256, 'udp': 17, 'tcp': 6, 'icmpv6': 58, 'icmp': 1, 'igmp': 2.

The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.

IPv6 Address type. Enumeration: 'iPv4': 1, 'iPv6': 2.

The ACL Profile destination IP address mask. If DST-IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'

IPv6 Address type. Enumeration: 'iPv4': 1, 'iPv6': 2.

The ACL Profile source IP address mask. If SRC-IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'

The ACL Profile UDP/TCP destination port mask. If DST-PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.

The ACL Profile UDP/TCP source port mask. If SRC-PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.

The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.

The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.

Indicate which Udf field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ UDF Offset1 0 (LSB) UDF Offset2 1 UDF Offset3 2 UDF Offset4 3 ------------------------------------------- The value is in Hex format.

The value of offset Chunk.

The value of offset MAsk.

The value of offset Chunk.

The value of offset MAsk.

The value of offset Chunk.

The value of offset MAsk.

The value of offset Chunk.

The value of offset MAsk.

This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted.

A table to configure L2 filter rules in the system.

Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID.

L2 Filter rule ID. 0 means auto assign.

ACL Profile ID which this rule join.

The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition.

Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition.

Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address

Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.

802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition.

The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting.

The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting.

Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded. Enumeration: 'replaceQueue': 7, 'replace1P': 6, 'drop': 2, 'rateLimit': 4, 'allow': 1, 'mirror': 3, 'replaceDSCP': 5.

Rate limit for matched packet.

Replace DSCP for matched packet.

Replace DSCP for matched packet.

ACL L2 Rule Replace Queue.

ACL L2 Filter Time Range

Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.

Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.

Specifies the complete set of Vlan over which this filter is applied for packets ingress at vlan . Notice : Only support one VLAN.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table to configure L3 filter rules in the system.

Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID.

L3 Filter rule ID. 0 means auto assign.

The Profile ID which this rule join.