DGS-1100-10ME_A1: View SNMP OID List / Download MIB

System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) V + _ = .

Version number of the Hardware.

Version number of the Firmware.

A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software.

Version number of the BootLoader.

This time is used to count the time and logout web or telnet interface automatically.

The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.

The textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is known, the value is the zero-length string.

This object is used to set Safeguard Enable\Disable. Enumeration: 'disabled': 2, 'enabled': 1.

This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. This objects also allows user to reset swith(all configuration set to default) and reset switch without ip(except ip configuration saved, configuration set to default) and reset switch without ip and vlan(except ip and vlan configuration saved, configuration set to default) When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to noreboot. Enumeration: 'reset': 3, 'resetwithoutip': 4, 'reboot': 2, 'noreboot': 1, 'resetwithoutipvlan': 5.

This object is used to save Configuration.

Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1522 bytes) of up to 10,000 bytes (tagged). Default jumbo frame is disabled. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates auto config is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for Enabled(1) or Disabled(2) Web state in the system. Enumeration: 'disabled': 2, 'enabled': 1.

Web Server Port Number.

This object is for ARP aging time.

This object is for MAC aging time.

Enable/Disable management Telnetsetting mechanism. Enumeration: 'disabled': 2, 'enabled': 1.

The value is for setting telnet's UDP Port.

To set the WEB panel auto refresh timer. Enumeration: 'refreshtime1min': 3, 'refreshtime5mins': 4, 'refreshtime30secs': 2, 'refreshimenever': 0, 'refreshtime10secs': 1.

Ethernet address (base address) of the Switch. This base Mac Address, if modified, will take effect only when the Switch is restarted.

The date is configured in the switch in the format, Hours:Minutes:Seconds Day Month Year e.g 19:10:31 11 08 2005 01-12 Month - beginning from January to December The railway time 00 to 24 hours can be configured and displayed. The Display of the date is in the format , WeekDay Month Day Hours:Minutes:Seconds Year e.g 04 09 21 18:11:30 2005 01-07 WeekDay - beginning from Sunday to Saturday 01-12 Month - beginning from January to December

This is DHCP auto configuration timeout, the maxium time in seconds to wait before terminate.

The serial number assigned to this nvram sub-unit

Indicates the average CPU usage in last 5 second of the switch in percentage

Indicates the average CPU usage in last 1 minute of the switch in percentage

Indicates the average CPU usage in last 5 minute of the switch in percentage

Indicates the average RAM usage in last 5 second of the switch in percentage

Indicates the average RAM usage in last 1 minute of the switch in percentage

Indicates the average RAM usage in last 5 minute of the switch in percentage

Cli Prompt string, some special value definition as below: 1. default - represent using the default value; 2. username - using the current login username;

Enable/Disable management SSH . Enumeration: 'disabled': 2, 'enabled': 1.

The value is for setting SSH's tcp Port.

A table to control the port specific parameters of the device like speed, duplex mode, etc.

An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.

Interface index of the port for the configuration in this entry applies.

This object indicates the port type: fiber 1G/100M or copper. Enumeration: 'copper': 1, 'fiber': 2.

Configures port speed which the mediatype is match with portCtrlDetailMediumType. Enumeration: 'disabled': 7, 'full100m': 2, 'full1000m': 1, 'half10m': 5, 'auto': 6, 'half100m': 3, 'full10m': 4.

The port's operating speed state. Enumeration: 'full1000m': 2, 'full100m': 3, 'down': 1, 'half10m': 6, 'half100m': 4, 'full10m': 5.

Configures interface auto/mdi/mdix mode. The default setting is Auto. Enumeration: 'auto': 1, 'mdi': 2, 'mdix': 3.

Enables / disables flow control for the interface. Enumeration: 'disabled': 2, 'enabled': 1.

Show Enables / disables status of flow control for the interface. Enumeration: 'disabled': 2, 'enabled': 1.

Enables / disables Admin for the interface. Enumeration: 'disabled': 2, 'enabled': 1.

Get the port's current media type Enumeration: 'fiberwith100BaseSFPModule': 3, 'gigabitethernet': 2, 'fiberwith1GBaseSFPModule': 4, 'fastethernet': 1.

Enables / disables dynamic mac auto learning for the interface. Enumeration: 'disabled': 2, 'enabled': 1.

The port description table.

The port description entry.

This object indicates the port index.

This object indicates the port type: fiber or copper. Enumeration: 'copper': 1, 'fiber': 2.

This object indicates the port description.

The port error table.

A list of information for the err port of the device.

This object indicates the module's port number.(1..Max port number in the module)

This object decides whether the port state is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

This object decides whether the PortStatus is err-disabled. Enumeration: 'other': 1, 'err-disabled': 2.

This object decides whether the PortStatus is LBD, Traffic Control, DULD. Enumeration: 'trafficcontrol': 2, 'lbd': 1, 'duld': 3.

A table to display the TX/RX frames per second and port utilization.

An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.

Interface index of the port for the configuration in this entry applies.

The total number of frames forwarded on the interface during last second.

The total number of frames received on the interface during last second.

interface frame usage during last second.

Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the default IPv4 address configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the default IPv4 address configured in the system. Enumeration: 'dynamic': 2, 'manual': 1.

Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.

IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.

Gateway

Status of DHCP Option12 Enumeration: 'enable': 1, 'disable': 2.

Host name in DHCP option 12

The state of IPv6 function. Enumeration: 'disabled': 2, 'enabled': 1.

The state of DHCPv6 that you want this interface to be in. Enumeration: 'disabled': 2, 'enabled': 1.

This object is to set the status of ipv6 link local address auto-generated. if set enabled, system will auto-generate a link-local ipv6 address by switch base mac addree. if set disabled, link-local address will be configured by mannual. Enumeration: 'disabled': 2, 'enabled': 1.

The NS's retransmit time that you want this interface to be in

This table contains dynamic routes that are learnt through dynamic routing protocol as well as local routes derived from configured address prefixes and statically configured routes.

An entry in the IPv6 Routing Table. An entry can be created by means of the routing protocol, derived from configured address prefixes as well as statically configured. There can be a static route as well as dynamic routes with the same destination and prefix length.

The routing mechanism via which this route was learned. If it has value local(2), it indicates this route was derived from a configured address prefix. Enumeration: 'dynamic': 4, 'static': 3.

Next hop IPv6 Address for this route. For direct routes it has the value ::0.

The index value which uniquely identifies the interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ipv6IfIndex.

The routing metric associated with this route.

Administrative Status of the route. This object is used to create or delete the route entry. The ipv6DefaultRouteIfIndex needs to be set, before the route entry is made active. CreateAndGo is not supported.

A list of interface entries.

An entry containing management information applicable to a particular interface.

The index of this IPv6 entry.

The ip address of this IPv6 entry.

The ip prefix of this IPv6 entry.

The ip type of this IPv6 entry. Enumeration: 'unicast': 1, 'linklocal': 3.

The status of an entry. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available.

Retry count of dhcp.

This is a trap that will send to snmp manager,and it will be generated when device receive a gratuitous arp packet and ip address is the same as the one of device.

The TFTP server's IP address is used to upload or download firmware.

Type of IP interface. Enumeration: 'iPv4': 1, 'iPv6': 2.

Specifies the interface name when the tftpFwTargetServerIpAddress is linklocal address.

Configure firmware filename to download.

The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName. Enumeration: 'download': 1, 'none': 0, 'upload': 2.

The tftp operation status represent firmware backup or upgrade status. Enumeration: 'fail': 2, 'transmit': 4, 'none': 0, 'progressing': 3, 'success': 1.

The file transfer percentage of the file upload or download.

The TFTP server's IP address is used to upload or download configuration file.

Type of IP interface. Enumeration: 'iPv4': 1, 'iPv6': 2.

Specifies the interface name when the tftpCfgTargetServerIpAddress is linklocal address.

The configuration filename is used to store or retrieve config from the tftp server.

The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName. Enumeration: 'download': 1, 'progressing': 3, 'upload': 2.

The tftp operation status represent configuration file backup or restore status. Enumeration: 'fail': 2, 'none': 0, 'progressing': 3, 'success': 1.

enable will save system log to file. Enumeration: 'enable': 1, 'disable': 2.

The TFTP server's IP address is used to upload or download system log file.

Type of IP interface. Enumeration: 'iPv4': 1, 'iPv6': 2.

Specifies the interface name when the tftpSyslogTargetServerIpAddress is linklocal address.

The system log filename is used to store or retrieve system log from the tftp server.

The tftp operates to perform either downloading the system log file to the unit or uploading the current system log file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName. Note: enable means backup system log file from dut. Enumeration: 'enable': 1, 'disable': 2.

The tftp operation status represent system log file backup or restore status. Enumeration: 'fail': 2, 'none': 0, 'progressing': 3, 'success': 1.

The file transfer percentage of the file upload or download.

This is a trap that will send to snmp manager,and it will be generated when Firware upgrade success.

This is a trap that will send to snmp manager,and it will be generated when Firware upgrade with issegalfile.

This is a trap that will send to snmp manager,and it will be generated when transfer file failed.

This is a trap that will send to snmp manager,and it will be generated when Firware with wrong checksum .

This is a trap that will send to snmp manager,and it will be generated when Firware upgrade failed.

A table to management user table in the switch.

An entry appears in this table for each user in the system.

The name of user entry.

The password of user entry. 0 means no password.

The access right of user entry. Enumeration: 'admin': 1, 'operator': 2, 'user': 3.

The encrypt type of user password. Enumeration: 'plainText': 1, 'sha1': 2.

Enable or disable Encrypt of user password. Enumeration: 'disabled': 2, 'enabled': 1.

The row status of user entry.

encrypt control of user password, default password storage type is plaintext, if set enable, all password storage is dlinksha1 format. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling SNMP Community function. Enumeration: 'disabled': 2, 'enabled': 1.

The table of snmp user.

The list of snmp user entry.

A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.

A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. Enumeration: 'v2c': 2, 'v1': 1, 'v3': 3.

The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.

An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of UserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoAuthProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoAuthProtocol, then an 'inconsistentValue' error must be returned. If a set operation tries to set the value to the NoAuthProtocol while the UserPrivProtocol value in the same row is not equal to NoPrivProtocol, then an 'inconsistentValue' error must be returned. That means that an SNMP command generator application must first ensure that the UserPrivProtocol is set to the NoPrivProtocol value before it can set the UserAuthProtocol value to NoAuthProtocol. Enumeration: 'sha': 3, 'none': 1, 'md5': 2.

Password of snmp user auth protocol.

An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of usmUserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoPrivProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoPrivProtocol, then an 'inconsistentValue' error must be returned. Note that if any privacy protocol is used, then you must also use an authentication protocol. In other words, if usmUserPrivProtocol is set to anything else than NoPrivProtocol, then the corresponding instance of usmUserAuthProtocol cannot have a value of usmNoAuthProtocol. If it does, then an 'inconsistentValue' error must be returned. Enumeration: 'none': 1, 'des': 2.

Password of snmp user priv protocol.

The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified, except for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active.

The table of snmp group.

The list of snmp group entry.

The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.

In order to gain the access rights allowed by this conceptual row, this securityModel must be in use. Enumeration: 'v2c': 2, 'v1': 1, 'v3': 3.

The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If multiple entries are equally indexed except for this vacmAccessSecurityLevel index, then the entry which has the highest value for vacmAccessSecurityLevel is selected. Enumeration: 'noAuthNoPriv': 1, 'authPriv': 3, 'authNoPriv': 2.

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.

The table of snmp view tree.

The list of snmp view tree entry.

The human readable name for a family of view subtrees.

The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees.

The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub-identifier of vacmViewTreeFamilySubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if, for each sub-identifier of the value of vacmViewTreeFamilySubtree, either: the i-th bit of vacmViewTreeFamilyMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of vacmViewTreeFamilySubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of vacmViewTreeFamilySubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of vacmViewTreeFamilySubtree. Note that masks of length greater than zero length do not need to be supported. In this case this object is made read-only.

Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or excluded from the MIB view. Enumeration: 'included': 1, 'excluded': 2.

The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.

The table of snmp community.

The list of snmp community entry.

The unique index value of a row in this table.

A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format.

The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpCommunityName and snmpCommunitySecurityName objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpCommunityStatus is active(1).

The table of snmp host.

The list of snmp host entry.

This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.

Type of IP interface. Enumeration: 'iPv4': 1, 'iPv6': 2.

The locally arbitrary.

The Level of Security to be used when generating SNMP messages using this entry. Enumeration: 'v2c': 2, 'v1': 1, 'v3-NoAuthNoPriv': 3, 'v3-AuthPriv': 5, 'v3-AuthNoPriv': 4.

The status of this conceptual row in the snmpHostTable.

An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the value of the snmpEngineID of a remote SNMP engine with which this user can communicate.

This object is for enabling or disabling SNMP login fail event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling devie Bootup event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling devie bootup event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling fiber port link up / link down event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling twisted pair port link up / link down event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling firmware upgrade success or fail event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling port security event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling lbd event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling send gratuitous trap when IP address conflicted in the network. Enumeration: 'disabled': 2, 'enabled': 1.

Enable/Disable management VLAN mechanism. Enumeration: 'disabled': 2, 'enabled': 1.

The management VLAN ID, which will allow to forward packets of that VLAN to CPU.

Enable/Disable IEEE 802.1Q PVID Auto assign Enumeration: 'disabled': 2, 'enabled': 1.

Enable/Disable IEEE 802.1Q Asymmetric VLAN Enumeration: 'disabled': 2, 'enabled': 1.

A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.

Information for a VLAN configured into the device by (local or network) management.

Vlan id used to identify the VLAN.

An administratively assigned string, which may be used to identify the VLAN.

The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed.

The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option.

The status of a row in sysDot1qVlanTable. By setting this object, new entries can be created in sysDot1qVlanTable and existing entries can be removed from sysDot1qVlanTable. It can be used as specified in the SNMP v2 standard.

A table containing per port control and status information for VLAN configuration in the device.

Information controlling VLAN configuration for a port on the device.

Port index.

The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port.

A list of the Static MACs

A Static MAC entry containing the mac and forwarding port.

The VLAN ID of the static MAC entry.

The MAC address associated of the static MAC entry.

The forwarding port of the static MAC entry.

The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC.

A table that contains information about unicast entries for which the device has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame. This table maintains context ID as one more index to support Multiple Instances.

Information about a specific unicast MAC address for which the device has some forwarding and/or filtering information.

The identity of this Filtering Database.

A unicast MAC address for which the device has forwarding and/or filtering information.

The port number of the port on which a frame having a source address equal to the value of the corresponding instance of dynamicFdbMacAddr has been seen.If the port is LA port, will show 'po' before port.

The status of this entry. The meanings of the values are: other(1) - none of the following. This may include the case where some other MIB object (not the corresponding instance of dynamicFdbPort, nor an entry in the fsDot1qStaticUnicastTable) is being used to determine if and how frames addressed to the value of the corresponding instance of dynamicFdbMacAddr are being forwarded. invalid(2) - this entry is no longer valid (e.g., it was learned but has since aged out), but has not yet been flushed from the table. learned(3) - the value of the corresponding instance of dynamicFdbPort was learned and is being used. self(4) - the value of the corresponding instance of dynamicFdbMacAddr represents one of the device's addresses. The corresponding instance of dynamicFdbPort indicates which of the device's ports has this address. static(5) - the value of the corresponding instance of dynamicFdbMacAddr is also the value of an existing instance of fsDot1qStaticAddress. deleteOnReset(6) - the value of the corresponding instance of fsDot1qTpFdbAddress and the port of this entry enablement Port security and set Lock address mode to Delete on Reset. deleteOnTimeout(7) - the value of the corresponding instance of fsDot1qTpFdbAddress and the port of this entry enablement Port security and set Lock address mode to Delete on TimeOut. permanent(8) - the value of the corresponding instance of fsDot1qTpFdbAddress and the port of this entry enablement Port security and set Lock address mode to Permanent. Enumeration: 'self': 4, 'dynamic': 3, 'invalid': 2, 'permanent': 8, 'other': 1, 'static': 5, 'deleteOnTimeout': 7, 'deleteOnReset': 6.

Fdb clear object identification: If cmFdbClearAction is clear by port, then this value is a port number; If cmFdbClearAction is clear by vlan, then this value is a port vlan id; otherwise this value is not used.

Fdb clear action identification: ClearAll to clear all fdb entries; ClearClearAllByVlanId clear all fdb entries that belong to specified vlan id; ClearAllByPort clear all fdb entries that belong to specified port Enumeration: 'clearByVlanId': 2, 'clearAll': 1, 'clearByPort': 3.

Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops performing protocol operations. Enumeration: 'disabled': 2, 'enabled': 1.

Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module forwards report packets to router port only. When set to 'disabled', the IGS module forwards report packets to all port. Enumeration: 'disabled': 2, 'enabled': 1.

This table contains the list of ports through which a router, in a particular VLAN is reachable.

Contains the VLAN ID and list of ports on which routers are present in the VLAN.

VLAN ID of the ports through which router is reachable.

List of static ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.

List of dynamic ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.

This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system.

Contains snooping status , version and fast leave configuration for a specific VLAN.

Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done.

This object allows you to enable/disable IGS function on a specific VLAN. Enumeration: 'disabled': 2, 'enabled': 1.

Indicates whether the switch is configured as a querier in the VLAN Enumeration: 'disabled': 2, 'enabled': 1.

The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries. Enumeration: 'disabled': 2, 'enabled': 1.

This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network.

Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table. Enumeration: 'disabled': 2, 'enabled': 1.

This object allows you to set igmp version function on a specific VLAN. Enumeration: 'igmp_v3': 3, 'igmp_v2': 2, 'igmp_v1': 1.

This is the interval (in seconds) after which a learnt router port entry will be purged for a specific VLAN. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.

This is the interval (in seconds) after which a learnt port entry will be purged for a specific VLAN. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.

When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number for a specific VLAN queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'RobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.

The value of this attribute defines the time period with which the specific VLAN will send group specific queries on a port to check if there is any interested receivers. The switch will send 'RobustnessValue' queries before removing the port from the group membership information in the forwarding database.

The maximum query response time advertised General queries on this interface.

This table contains MAC based multicast forwarding information.

This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded.

VLAN ID pertaining to the Multicast forwarding entry

Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.

Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.

List of ports onto which the multicast data packets destined for this group will be forwarded.

This table is used to manage the IGMP Authentication function of the switch.

Contains management entities for IGMP Authentication function.

The port index of igsAccessAuthTable which indicates the port to be configured.

This object can be configured to set IGMP Authentication state to enabled/disabled on each port. Enumeration: 'disabled': 2, 'enabled': 1.

This table is used to manage the IGMP Host based Fast Leave function of the switch.

Contains management entities for IGMP Host based fast leave function.

VLAN ID of Host table entry.

Group address of Host table entry.

Port number of Host table entry.

Host IP address of Group in Host table entry.

Settings of Qos mode. Qos PortBase, 802.1p or DSCP mode. PortBase: When Qos in Port Base mode, ingress packets from each port SHOULD be forwarded to the specific queue according to Port Base Priority settings for traffic per-port classification 802.1p: When Qos is placed in 802.1P mode, ingress tagged packets SHOULD be classified to 8 different queues according to its carrying 802.1P priority and queue setting DSCP: When Qos in DSCP mode, ingress packets MUST be classified to the specified queue according to its DSCP and queue mapping Enumeration: 'portbase': 3, 'dscp': 2, 'dot1p': 1.

Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues. Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8. Queues with higher weights get bandwidth before than other queues with less weights. Enumeration: 'wrr': 2, 'strictPriority': 1.

A list of 802.1p port default priority Entries.

A list of 802.1p port default priority priorities.

A port identifier that is in the range of 1 to ifNumber.

For ingress packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization.

For ingress packets, the per port 'Effective Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization.

A table mapping evaluated User Priority to Traffic Class, for forwarding by the bridge.

User Priority to Traffic Class mapping.

The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type.

The Traffic Class the received frame is mapped to.

A list of sysQosScheduling.

A list of sysQosScheduling Weight.

A index of class 0 ~ 7.

cos weight

DiffServ Type 0 : IP ToS value = 0

DiffServ Type 01 : IP ToS value = 4

DiffServ Type 02 : IP ToS value = 8

DiffServ Type 03 : IP ToS value = 12

DiffServ Type 04 : IP ToS value = 16

DiffServ Type 05 : IP ToS value = 20

DiffServ Type 06 : IP ToS value = 24

DiffServ Type 07 : IP ToS value = 28

DiffServ Type 08 : IP ToS value = 32

DiffServ Type 09 : IP ToS value = 36

DiffServ Type 10 : IP ToS value = 40

DiffServ Type 11 : IP ToS value = 44

DiffServ Type 12 : IP ToS value = 48

DiffServ Type 13 : IP ToS value = 52

DiffServ Type 14 : IP ToS value = 56

DiffServ Type 15 : IP ToS value = 60

DiffServ Type 16 : IP ToS value = 64

DiffServ Type 17 : IP ToS value = 68

DiffServ Type 18 : IP ToS value = 72

DiffServ Type 19 : IP ToS value = 76

DiffServ Type 20 : IP ToS value = 80

DiffServ Type 21 : IP ToS value = 84

DiffServ Type 22 : IP ToS value = 88

DiffServ Type 23 : IP ToS value = 92

DiffServ Type 24 : IP ToS value = 96

DiffServ Type 25 : IP ToS value = 100

DiffServ Type 26 : IP ToS value = 104

DiffServ Type 27 : IP ToS value = 108

DiffServ Type 28 : IP ToS value = 112

DiffServ Type 29 : IP ToS value = 116

DiffServ Type 30 : IP ToS value = 120

DiffServ Type 31 : IP ToS value = 124

DiffServ Type 32 : IP ToS value = 128

DiffServ Type 33 : IP ToS value = 132

DiffServ Type 34 : IP ToS value = 136

DiffServ Type 35 : IP ToS value = 140

DiffServ Type 36 : IP ToS value = 144

DiffServ Type 37 : IP ToS value = 148

DiffServ Type 38 : IP ToS value = 152

DiffServ Type 39 : IP ToS value = 156

DiffServ Type 40 : IP ToS value = 160

DiffServ Type 41 : IP ToS value = 164

DiffServ Type 42 : IP ToS value = 168

DiffServ Type 43 : IP ToS value = 172

DiffServ Type 44 : IP ToS value = 176

DiffServ Type 45 : IP ToS value = 180

DiffServ Type 46 : IP ToS value = 184

DiffServ Type 47 : IP ToS value = 188

DiffServ Type 48 : IP ToS value = 192

DiffServ Type 49 : IP ToS value = 196

DiffServ Type 50 : IP ToS value = 200

DiffServ Type 51 : IP ToS value = 204

DiffServ Type 52 : IP ToS value = 208

DiffServ Type 53 : IP ToS value = 212

DiffServ Type 54 : IP ToS value = 216

DiffServ Type 55 : IP ToS value = 220

DiffServ Type 56 : IP ToS value = 224

DiffServ Type 57 : IP ToS value = 228

DiffServ Type 58 : IP ToS value = 232

DiffServ Type 59 : IP ToS value = 236

DiffServ Type 60 : IP ToS value = 240

DiffServ Type 61 : IP ToS value = 244

DiffServ Type 62 : IP ToS value = 248

DiffServ Type 63 : IP ToS value = 252

A table to control the rate limiting parameters either for the entire switch or for each interface in the switch.

An entry appears in this table for each physical interface in the switch.

The interface index for which the configuration in this entry applies.

Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~100000(Kbits per second) in FE port, 64~1000000 (Kbits per second) in GE port.

Configures the new interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~100000(Kbits per second) in FE port, 64~1000000 (Kbits per second) in GE port.

Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~100000(Kbits per second) in FE port, 64~1000000(Kbits per second) in GE port.

Allows to configure the new limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~100000(Kbits per second) in FE port, 64~1000000(Kbits per second) in GE port.

The trap setting of traffic control. Enumeration: 'stormCleared': 2, 'none': 0, 'both': 3, 'stormOccurred': 1.

The traffic control table.

The traffic control entry.

The traffic control index.

The action mode of traffic control. Enumeration: 'drop': 0, 'shutdown': 1.

The control type of traffic control. (b: Broadcast, m: Multicast, u: Unknown Unicast) Enumeration: 'none': 0, 'b': 1, 'mb': 3, 'm': 2, 'um': 6, '': 4, 'umb': 7, 'ub': 5.

The threshold of traffic control. In drop mode,threshold should be times of 64,its range is 64 to 1000000,unit is kbps In Shutdown mode,threshold's range is 1 to 255000,unit is pkts per second

The count down value of traffic control.

The time interval of traffic control.

The Traffic control port status in shutdown mode. Enumeration: 'blocking': 1, 'shutdown': 2, 'normal': 0.

when storm event occur on the port ,it will send out storm occured snmp trap to snmp manager.

when storm event cleared on the port, it will send out a storm cleared snmp trap to snmp manager.

A table to control port security features of the device.

An entry appears in port security table for each interface in the system.

The interface index for which the configuration in this entry applies.

Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled. Enumeration: 'disabled': 2, 'enabled': 1.

Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 64. Note: Set value 0 means cannot learn MAC address.

Configures port security lock address mode for the interface. deleteOnReset : The locked addresses will not age out until the Switch has been reset. deleteOnTimeout : The locked addresses will age out after the aging timer expires. Permanent : The locked addresses will not age out after the aging timer expires. Enumeration: 'permanent': 3, 'deleteOnTimeout': 2, 'deleteOnReset': 1.

A table to control port security FDB Permanent of the device.

An entry appears in port security table for each interface in the system.

The VLAN ID of the port security MAC entry.

The MAC address associated of the port security MAC entry.

The forwarding port of the port security MAC entry.

This object indicates the status of this entry. The default value is permanent(3). other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out. Enumeration: 'permanent': 3, 'other': 0, 'deleteOnTimeout': 2, 'invalid': 4, 'deleteOnReset': 1.

This object indicates the status of Port Security entry when the value of this boject is setted to false ,this specific enntry will be delete form dynamic FDB and Port Security Entry Enumeration: 'false': 2, 'true': 1.

A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel

There is one entry in this table for each created port-channel port

The ifIndex of the port-channel(Aggregator's interface index).

Port list of port channel.

This object indicates the Access Authentication is enable or disable. Enumeration: 'disabled': 2, 'enabled': 1.

Timeout in second for login authentication response.

The amount for login authentication, if login failure exceed, connection or access would be locked.

This object is used to set Local Enable Password.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP.

A table that contains information about Login authentication method lists.

A list of the Authentication methods.

A human-readable text string of the method list.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table that contains information about Enable authentication method lists.

A list of the Authentication methods.

A human-readable text string of the method list.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table that contains informations about server group.

A list of the group including servers.

A human-readable text string of the method group.

The list of servers in the group, each bit indicates a specified server ID. The server must be created before including it. Bits: 'id8': 7, 'id9': 8, 'id6': 5, 'id7': 6, 'id4': 3, 'id5': 4, 'id2': 1, 'id3': 2, 'id1': 0, 'id10': 9, 'id11': 10, 'id12': 11, 'id13': 12, 'id14': 13, 'id15': 14, 'id16': 15.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table that contains information about radius severs.

A list of the information of server .

The IP address of the radius AAC server IP type referred to in this table entry. (IPv4=1, IPv6=2) Enumeration: 'ipv4': 1, 'ipv6': 2.

The IP address of radius Server

A value that uniquely identifies this SwAACServerGroupEntry.

Specifies the interface name when the aacServerIPAddr is linklocal address.

The TCP/IP port .

The key used while authentication process.

radius Server response timeout .

Client retry count . (-1: No retry mechanism)

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

System SHOULD send out a trap message in violation that the learning entries exceeds the max learning address set of port security.

This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection. Enumeration: 'disabled': 2, 'enabled': 1.

A table to configure IP authorized managers in the system.

Each entry in this table represents rules for particular IP authorized manager.

Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.

Used to mask with IP address, it allow you set a subnet as a trusted host entry.

This object indicates the status of this entry.

A table that contains ARP infomation

An entry appears in this table for each interface in the system.

The IpAddress corresponding to the Mac Address.

Ethernet Mac Address.

The type of ARP mapping entry. Enumeration: 'static': 2, 'dynamic': 1.

The status of an entry in the ARP Table. A conceptual row can not be made active until the arpMacAddress object has been set.

clear action type: none(0), -- no action clearAll(1), -- clear all arp entries cleatAllStatic, -- clear all static arp entries clearAllDynamic, -- clear all dynamic arp entries Initial its value is 0, and after each action, it will reset to 0 Enumeration: 'clearAllDynamic': 3, 'none': 0, 'clearAll': 1, 'cleatAllStatic': 2.

This object is for enabling or disabling syslog alert features in the system and the syslog will save to flash or send to remote syslog server. System Logs record and manage events, as well as report errors and informational messages. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for choosing the method to save syslog into flash. Enumeration: 'timeInterval': 1, 'logTrigger': 2, 'onDemand': 0.

When savemode is time interval, it's used to set the interval minutes of system save syslog to flash.

Clears the buffered logs. This object is set to 'false' by default. When set to 'True', the buffered logs will be cleared and the value of this object will become 'false' again.

The table of syslog remote server.

The list of syslog remote server entry.

The index of syslog remote server.

Specifies the Address type of server.Address type shall be ipv4 or ipv6. Enumeration: 'ipv4': 1, 'ipv6': 2.

Specifies the ServerIP to which the syslog shall be forwarded.

Specifies the log level option to be set for a specific server. Enumeration: 'debug': 7, 'information': 6, 'warning': 4.

The Syslog standard facilities. The facility to be used when sending Syslog messages to this server. Enumeration: 'local5': 168, 'local4': 160, 'local7': 184, 'local6': 176, 'local1': 136, 'local0': 128, 'local3': 152, 'local2': 144.

The value is for setting UDP Port.

The status for this server. If enable, system will send message to this server. Enumeration: 'disabled': 2, 'enabled': 1.

Row status of this server entry.

Specifies the number of messages .

An entry (conceptual row) in the syslogMsgTable.

The auxiliary variable used for identifying instances of the columnar objects in the syslogMsgTable.

A textual description of system log message.

time of system log message.

Severity of system log message. Enumeration: 'information': 6, 'notice': 5, 'emergency': 0, 'alert': 1, 'critical': 2, 'error': 3, 'debug': 7, 'warning': 4.

Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged switchs.The Switch will automatically shutdown the port and sends a log to the administrator. Enumeration: 'disabled': 2, 'enabled': 1.

Loopback detection function mode. Enumeration: 'vlan': 2, 'port': 1.

Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP packet automatically.

This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop Detection Recover Time. The default is 60 seconds.

A table to control Loopback detection features either for the entire switch or for each interface in the switch.

An entry appears in this table for each interface in the system.

The interface index of the port for which the configuration in this entry applies.

Provides control to per port enable or disable the loopback detection function. Default is disabled. Enumeration: 'disabled': 2, 'enabled': 1.

The loop status for this port. Enumeration: 'loop': 2, 'normal': 1.

A table to display Loopback detection features by vlan mode .

An entry appears in this table for each interface in the system.

Display port lists loop status by vlan.

Display port lists loop status by vlan.

This object indicates the VLANs that enabled LBD. Note: For the LBD enabled VLAN specification, the value should be separated by ',' or '-'. Such as: 1,4,7 or 1,4,7-9 .

A loopbackOccur notification is sent when loop found.

A loopbackRecovery notification is sent when recovery time comes to end.

Enable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the packet can be studied. Enumeration: 'disabled': 2, 'enabled': 1.

Provides control to enable or disable mirroring of ingress or Egress traffic over this interface to the mirrored-to port.

Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.

Specifies the port to which the mirrored traffic in the system is to be copied.

Specifies the port to which the mirrored traffic in the system is to be copied.

Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.

Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.

Specifies the validity of the entry, max entry number is 4.

A list of the Static MACs

A Static MAC entry containing the mac and forwarding port.

The VLAN ID of the static MAC entry.

The MAC address associated of the static MAC entry.

The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length.

The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.

This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 284083276 (00:00:00 UTC, January 1, 2009) and smaller than 1136073599 (23:59:59 UTC, December 31, 2035).

SNTP Poll Interval In Seconds (30-99999)

Enable/Disable SNTP function in the system. Enumeration: 'local': 2, 'sntp': 1.

This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes. Enumeration: 'offset90min': 90, 'offset120min': 120, 'offset60min': 60, 'offset30min': 30.

Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)

Daylight saving time (DST) is a system of setting clocks ahead so that both sunrise and sunset occur at a later hour. The effect is additional daylight in the evening. Many countries observe DST, although most have their own rules and regulations for when it begins and ends. The dates of DST may change from year to year. The Valid format [dayofmonth-month,HH:MM]. Example:- 01-Apr,17:30

Daylight saving time (DST) is a system of setting clocks ahead so that both sunrise and sunset occur at a later hour. The effect is additional daylight in the evening. Many countries observe DST, although most have their own rules and regulations for when it begins and ends. The dates of DST may change from year to year. The Valid format [dayofmonth-month,HH:MM]. Example:- 01-Apr,17:30

This object is for Annual(1) or Disabled(2) DST state in the system. Enumeration: 'disabled': 2, 'annual': 1.

The table contains configured SNTP/NTP servers in the system.

Each entry in the table contains necessary information to send SNTP request to the servers.

The IP address type ipv4 or ipv6. Enumeration: 'ipv4': 1, 'ipv6': 2.

The unicast IPv4/IPv6 server address in the Unicast Addressing mode

In Unicast addressing mode, we can have primary and secondary servers. This flag is to distinguish between primary and secondary server. SNTP client sends request to different servers until it receives successful response. This flag tells the order in which to query the servers. Enumeration: 'primary': 1, 'secondary': 2.

The activation of a row adds server entry. The destruction of a row removes server entry

This object is for enabling or disabling RMON function. Enumeration: 'disabled': 2, 'enabled': 1.

A list of Ethernet statistics entries.

A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1

The value of this object uniquely identifies this entry.

This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated etherStatsStatus object is equal to valid(1).

The entity that configured this entry and is therefore using the resources assigned to it.

The status of this etherStats entry.

The total number of events in which packets were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.

The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets). This object can be used as a reasonable estimate of 10-Megabit ethernet utilization. If greater precision is desired, the etherStatsPkts and etherStatsOctets objects should be sampled before and after a common interval. The differences in the sampled values are Pkts and Octets, respectively, and the number of seconds in the interval is Interval. These values are used to calculate the Utilization as follows: Pkts * (9.6 + 6.4) + (Octets * .8) Utilization = ------------------------------------- Interval * 10,000 The result of this equation is the value Utilization which is the percent utilization of the ethernet segment on a scale of 0 to 100 percent.

The total number of packets (including bad packets, broadcast packets, and multicast packets) received.

The total number of good packets received that were directed to the broadcast address. Note that this does not include multicast packets.

The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address.

A list of history control entries.

A list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyControlInterval.2

An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.

This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated historyControlStatus object is equal to valid(1).

The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry. When this object is created or modified, the probe should set historyControlBucketsGranted as closely to this object as is possible for the particular probe implementation and available resources.

The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This interval can be set to any number of seconds between 1 and 3600 (1 hour). Because the counters in a bucket may overflow at their maximum value with no indication, a prudent manager will take into account the possibility of overflow in any of the associated counters. It is important to consider the minimum time in which any counter could overflow on a particular media type and set the historyControlInterval object to a value less than this interval. This is typically most important for the 'octets' counter in any media-specific table. For example, on an Ethernet network, the etherHistoryOctets counter could overflow in about one hour at the Ethernet's maximum utilization. This object may not be modified if the associated historyControlStatus object is equal to valid(1).

The entity that configured this entry and is therefore using the resources assigned to it.

The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1).

A list of alarm entries.

A list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8

An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device.

The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in the case of deltaValue sampling - the interval should be set short enough that the sampled variable is very unlikely to increase or decrease by more than 2^31 - 1 during a single sampling interval. This object may not be modified if the associated alarmStatus object is equal to valid(1).

The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, Counter64, Gauge, or TimeTicks) may be sampled. Because SNMP access control is articulated entirely in terms of the contents of MIB views, no access control mechanism exists that can restrict the value of this object to identify only those objects that exist in a particular MIB view. Because there is thus no acceptable means of restricting the read access that could be obtained through the alarm mechanism, the probe must only grant write access to this object in those views that have read access to all objects on the probe. During a set operation, if the supplied variable name is not available in the selected MIB view, a badValue error must be returned. If at any time the variable name of an established alarmEntry is no longer available in the selected MIB view, the probe must change the status of this alarmEntry to invalid(4). This object may not be modified if the associated alarmStatus object is equal to valid(1).

The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), the value of the selected variable will be compared directly with the thresholds at the end of the sampling interval. If the value of this object is deltaValue(2), the value of the selected variable at the last sample will be subtracted from the current value, and the difference compared with the thresholds. This object may not be modified if the associated alarmStatus object is equal to valid(1). Enumeration: 'absoluteValue': 1, 'deltaValue': 2.

A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval was less than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is greater than or equal to this threshold and the associated alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3). After a rising event is generated, another such event will not be generated until the sampled value falls below this threshold and reaches the alarmFallingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).

A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was greater than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is less than or equal to this threshold and the associated alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3). After a falling event is generated, another such event will not be generated until the sampled value rises above this threshold and reaches the alarmRisingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).

The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).

The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).

The entity that configured this entry and is therefore using the resources assigned to it.

The status of this alarm entry.

A list of events to be generated.

A set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be named eventLastTimeSent.6

An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur.

A comment describing this event entry.

The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-trap, an SNMP trap is sent to one or more management stations. Enumeration: 'snmptrap': 3, 'none': 1, 'log': 2, 'logandtrap': 4.

If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string.

The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has associated entries in the log table, all connected management stations should retrieve those log entries, as they may have significance to all management stations connected to this device

The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent.

The value of sysUpTime at the time this event entry last generated an event. If this entry has not generated any events, this value will be zero.

Enable/Disable Static 802.1x. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates the authentication mode of the device. Enumeration: 'portBase': 1, 'macBase': 2.

The authentication method used to authenticate users. Enumeration: 'pnacProtocolRadiusEap': 1, 'pnacProtocolLocal': 2.

Enable/disable Radius Accounting Settings. Enumeration: 'disabled': 2, 'enabled': 1.

A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.

The configuration information for an Authenticator Port.

A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number.

The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine.

The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine.

The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine.

The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine.

The value of the maxReq constant currently in use by the Backend Authentication state machine.

The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine.

The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1). Enumeration: 'disabled': 2, 'enabled': 1.

The current value of the controlled Port control parameter for the Port. Enumeration: 'auto': 2, 'forceUnauthorized': 1, 'forceAuthorized': 3.

The current value of the controlled Port control parameter for the Port. Enumeration: 'authenticator': 1, 'none': 2.

The current value of the controlled Port control parameter for the Port. Enumeration: 'both': 0, 'in': 1.

The current value of the open control Port control parameter for the Port. Enumeration: 'both': 0, 'in': 1.

The authorized status of the open control Port. Enumeration: 'authorized': 1, 'unAuthorized': 2.

A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.

The configuration information for an Pnacenticator Port.

The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.

This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.

The status of this conceptual row in the pnacUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The pnacUserName objects must be explicitly set.

A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.

The configuration information for an Authenticator Port.

A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3.

The IP address of the RADIUS server IP type referred to in this table entry. Enumeration: 'ipv4': 1, 'ipv6': 2.

The IP address of the RADIUS server referred to in this table entry.

The value is for setting UDP Port.

The value is for setting UDP Port.

The value is for setting UDP Port.

The value is for setting UDP Port.

This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.

The status of this conceptual row in the pnacRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The pnacRadiusServerIndex objects must be explicitly set.

The VLAN name of guest VLAN.

This object indicates the guest VLAN port members of this device.

Used to delete the guest VLAN. Enumeration: 'start': 2, 'none': 1.

This object can enabled or disabled MAC Notification. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates the time interval in second for trigger the MAC notify message.

This object indicates the history size of variation MAC in address table. The default value is 1 .

A table to control Loopback detection features either for the entire switch or for each interface in the switch.

An entry appears in this table for each interface in the system.

The interface index of the port for which the configuration in this entry applies.

Provides control to per port enable or disable the mac notify status function. Default is disabled. Enumeration: 'disabled': 2, 'enabled': 1.

A fdbTableChanged notification is sent when dynamic forwarding table add learning mac; also when one device leave, dynamic forwarding table delete one mac,a fdbTableChanged notification is sent too. Note that transmission of fdbTableChanged notifications are throttled by the agent.

Enable/Disable IGMP Multicast Vlan function. Enumeration: 'disabled': 2, 'enabled': 1.

Information about the IGMP snooping multicast VLAN table.

The entry of sysIGMPMulticastVlanTable.

This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.

This object indicates InetAddressType IGS or MLD

This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.

This object indicates the port list of the source ports of the IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.

This object indicates the port list of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.

This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN.

This object can be used to enable or disable the IGMP snooping multicast VLAN. Enumeration: 'disabled': 2, 'enabled': 1.

The replacement source IP of this multicast VLAN.

This object indicates the status of this entry.

The table containing the IGMP snooping multicast VLAN group information

Information about the current IGMP snooping multicast VLAN group.

This object indicates the VID of the IGMP snooping multicast VLAN group.

This object indicates InetAddressType IGS or MLD

Specifies the multicast address list for this VLAN.

Specifies the multicast address list for this VLAN.

This object indicates the status of this entry.

This object indicates DHCP relay function is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates the maximum number of router hops that the BOOTP packets can cross.

This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.

This table indicates the IP address as a destination to forward (relay) DHCP packets to.

A list of information indicates the IP address as a destination to forward (relay) DHCP packets to.

This object indicates the DHCP server IP address.

This object indicates the input Interface Index value mapped to this Server Address Table.

This object indicates the status of this entry.

Only when enabled, the Relay Agent shall do any processing related to Relay Agent Information Options - like inserting the necessary options while relaying a packet from a client to a server and examining/stripping of options when relaying a packet from a server to a client. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates DHCP relay option 82 Check function is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates DHCP relay option 82 policy. Enumeration: 'keep': 3, 'drop': 2, 'replace': 1.

This object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defined by writing to the swDHCPRelayOption82RemoteID object. Enumeration: 'default': 1, 'userdefined': 2.

This object displays the current remote ID of the device. If DHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If DHCPRelayOption82RemoteIDType is set to user-defined, a new value can be written to this object.

This object indicates DHCP local relay function is enabled or disabled globally. Enumeration: 'disabled': 2, 'enabled': 1.

This table indicates the IP address as a destination to forward (local relay) DHCP packets to.

A list of information indicates the IP address as a destination to forward (local relay) DHCP packets to.

This object displays the current VLAN ID of the device.

This object indicates DHCP local relay function of VLAN is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

Provides control to LED port.

Enable/Disable Green LED function. Default is disabled. Enumeration: 'disabled': 2, 'enabled': 1.

The time profile name associated with the Schedule entry (e.g., `abc, bbb').

The time profile name associated with the Schedule entry (e.g., `abc, bbb').

Provides control to LED port.

Enable/Disable Green LED function. Default is disabled. Enumeration: 'disabled': 2, 'enabled': 1.

The time profile name associated with the Schedule entry (e.g., `abc, bbb').

The time profile name associated with the Schedule entry (e.g., `abc, bbb').

Enable/Disable Green LED function. Default is disabled. Enumeration: 'disabled': 2, 'enabled': 1.

The time profile name associated with the Schedule entry (e.g., `abc, bbb').

The time profile name associated with the Schedule entry (e.g., `abc, bbb').

Enable/Disable Power Saving Cable Length Detection. Enumeration: 'disabled': 2, 'enabled': 1.

This object is used for enabling or disabling LLDP in the system. Enumeration: 'disabled': 2, 'enabled': 1.

The time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpMessageTxInterval * lldpMessageTxHoldMultiplier))

This object is used for LLDP packet update frequency. The timer in units of seconds.

This object is used for LLDP Reinitialization Delay. The timer in units of seconds.

The lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local systems MIB. The recommended value for the lldpTxDelay is set by the following formula: 1 <= lldpTxDelay <= (0.25 * lldpMessageTxInterval).

The table that controls selection of LLDP management address TLV instances to be transmitted on individual ports.

LLDP configuration information that specifies the set of ports (represented as a PortList) on which the local system management address instance will be transmitted. Each active sysLLDPConfigManAddrEntry must be restored from non-volatile and re-created (along with the corresponding lldpLocManAddrEntry) after a re-initialization of the management system.

The type of management address identifier encoding used in the associated 'lldpLocManagmentAddr' object.

The string value used to identify the management address component associated with the local system. The purpose of this address is to contact the management entity.

A set of ports that are identified by a PortList, in which each port is represented as a bit. The corresponding local system management address instance will be transmitted on the member ports of the lldpManAddrPortsTxEnable. The default value for lldpConfigManAddrPortsTxEnable object is empty binary string, which means no ports are specified for advertising indicated management address instance.

The table that controls LLDP frame transmission on individual ports.

LLDP configuration information for a particular port. This configuration parameter controls the transmission and the reception of LLDP frames on those ports whose rows are created in this table.

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The value of this object is used as a port index to the sysLLDPPortConfigTable.

The administratively desired status of the local LLDP agent. If the associated lldpPortConfigAdminStatus object has a value of 'txOnly(1)', then LLDP agent will transmit LLDP frames on this port and it will not store any information about the remote systems connected. If the associated lldpPortConfigAdminStatus object has a value of 'rxOnly(2)', then the LLDP agent will receive, but it will not transmit LLDP frames on this port. If the associated lldpPortConfigAdminStatus object has a value of 'txAndRx(3)', then the LLDP agent will transmit and receive LLDP frames on this port. If the associated lldpPortConfigAdminStatus object has a value of 'disabled(4)', then LLDP agent will not transmit or receive LLDP frames on this port. If there is remote systems information which is received on this port and stored in other tables, before the port's lldpPortConfigAdminStatus becomes disabled, then the information will naturally age out. Enumeration: 'disabled': 4, 'rxOnly': 2, 'txOnly': 1, 'txAndRx': 3.

The lldpPortConfigNotificationEnable controls, on a per port basis, whether or not notifications from the agent are enabled. The value true(1) means that notifications are enabled; the value false(2) means that they are not.

The lldpPortConfigTLVsTxEnable, defined as a bitmap, includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to a TLV type associated with a specific optional TLV. It should be noted that the organizationally-specific TLVs are excluded from the lldpTLVsTxEnable bitmap. LLDP Organization Specific Information Extension MIBs should have similar configuration object to control transmission of their organizationally defined TLVs. The bit 'portDesc(0)' indicates that LLDP agent should transmit 'Port Description TLV'. The bit 'sysName(1)' indicates that LLDP agent should transmit 'System Name TLV'. The bit 'sysDesc(2)' indicates that LLDP agent should transmit 'System Description TLV'. The bit 'sysCap(3)' indicates that LLDP agent should transmit 'System Capabilities TLV'. There is no bit reserved for the management address TLV type since transmission of management address TLVs are controlled by another object, sysLLDPConfigManAddrTable. The default value for lldpPortConfigTLVsTxEnable object is empty set, which means no enumerated values are set. The value of this object must be restored from non-volatile storage after a re-initialization of the management system. Bits: 'sysCap': 3, 'sysName': 1, 'portDesc': 0, 'sysDesc': 2.

A table that controls selection of LLDP TLVs to be transmitted on individual ports.

LLDP configuration information that controls the transmission of IEEE 802.3 organizationally defined TLVs on LLDP transmission capable ports. Each active lldpXdot3PortConfigEntry must be from non-volatile storage (along with the corresponding sysLLDPPortConfigEntry) after a re-initialization of the management system.

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The value of this object is used as a port index to the sysLLDPPortConfigTable.

The lldpXdot3PortConfigTLVsTxEnable, defined as a bitmap, includes the IEEE 802.3 organizationally defined set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to an IEEE 802.3 subtype associated with a specific IEEE 802.3 optional TLV. The bit 0 is not used since there is no corresponding subtype. The bit 'macPhyConfigStatus(0)' indicates that LLDP agent should transmit 'MAC/PHY configuration/status TLV'. The bit 'maxFrameSize(1)' indicates that LLDP agent should transmit 'Maximum-frame-size TLV'. The default value for lldpXdot3PortConfigTLVsTxEnable object is an empty set, which means no enumerated values are set. The value of this object must be restored from non-volatile storage after a re-initialization of the management system. Bits: 'macPhyConfigStatus': 0, 'maxFrameSize': 1.

This table contains one row per port of Ethernet port information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent.

Information about a particular port component.

The value of this object is used as a port index to the lldpXdot3LocPortTable.

The truth value used to indicate whether the given port (associated with the local system) supports Auto-negotiation.

The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the local system.

This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the local system.

An integer value that indicates the operational MAU type of the given port on the local system. This object contains the integer value derived from the list position of the corresponding dot3MauType as listed in IETF RFC 3636 (or subsequent revisions) and is equal to the last number in the respective dot3MauType OID. For example, if the ifMauType object is dot3MauType1000BaseTHD which corresponds to {dot3MauType 29}, the numerical value of this field will be 29. For MAU types not listed in RFC 3636 (or subsequent revisions), the value of this field shall be set to zero.

This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent.

Maximum Frame Size information about a particular port component.

The value of this object is used as a port index to the lldpXdot3LocMaxFrameSizeTable.

An integer value indicating the maximum supported frame size in octets on the given port of the local system.

This table contains Ethernet port information (as a part of the LLDP 802.3 organizational extension) of the remote system.

Information about a particular physical network connection.

A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The lldpXdot3RemLocalPortNum identifies the port on which the remote system information is received. The value of this object is used as a port index to the lldpXdot3RemPortTable.

This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the lldpXdot3RemIndex will wrap between reboots.

The truth value used to indicate whether the given port (associated with remote system) supports Auto-negotiation.

The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the remote system.

This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the remote system.

An integer value that indicates the operational MAU type of the sending device. This object contains the integer value derived from the list position of the corresponding dot3MauType as listed in in IETF RFC 3636 (or subsequent revisions) and is equal to the last number in the respective dot3MauType OID. For example, if the ifMauType object is dot3MauType1000BaseTHD which corresponds to {dot3MauType 29}, the numerical value of this field will be 29. For MAU types not listed in RFC 3636 (or subsequent revisions), the value of this field shall be set to zero.

This table contains Ethernet power information (as a part of the LLDP 802.3 organizational extension) of the remote system.

Information about a particular physical network connection.

A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The lldpXdot3RemLocalPortNum identifies the port on which the remote system information is received. The value of this object is used as a port index to the lldpXdot3RemPortTable.

This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the lldpXdot3RemIndex will wrap between reboots.

The value that identifies the port Class of the given port associated with the remote system.

The truth value used to indicate whether the MDI power is supported on the given port associated with the remote system.

The truth value used to identify whether MDI power is enabled on the given port associated with the remote system.

The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair selection can be controlled on the given port associated with the remote system.

This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the remote system.

This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the remote system.

This table contains port link aggregation information (as a part of the LLDP 802.3 organizational extension) of the remote system.

Link Aggregation information about remote system's port component.

A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The lldpXdot3RemLocalPortNum identifies the port on which the remote system information is received. The value of this object is used as a port index to the lldpXdot3RemPortTable.

This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the lldpXdot3RemIndex will wrap between reboots.

The bitmap value contains the link aggregation capabilities and the current aggregation status of the link.

This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port component associated with the remote system. If the remote port is not in link aggregation state and/or it does not support link aggregation, this value should be zero.

This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) of the remote system.

Maximum Frame Size information about a particular port component.

A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The lldpXdot3RemLocalPortNum identifies the port on which the remote system information is received. The value of this object is used as a port index to the lldpXdot3RemPortTable.

This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the lldpXdot3RemIndex will wrap between reboots.

An integer value indicating the maximum supported frame size in octets on the port component associated with the remote system.

A table that controls selection of LLDP Port VLAN-ID TLVs to be transmitted on individual ports.

LLDP configuration information that controls the transmission of IEEE 802.1 organizationally defined Port VLAN-ID TLV on LLDP transmission capable ports. Each active lldpConfigEntry must be restored from non-volatile storage (along with the corresponding sysLLDPPortConfigEntry) after a re-initialization of the management system.

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The value of this object is used as a port index to the sysLLDPPortConfigTable.

The lldpXdot1ConfigPortVlanTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organizationally defined port VLAN TLV transmission is allowed on a given LLDP transmission capable port. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.

The table that controls selection of LLDP VLAN name TLV instances to be transmitted on individual ports.

LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System VLAN name instance will be transmitted. Each active lldpXdot1ConfigVlanNameEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocVlanNameEntry) after a re-initialization of the management system.

The value of this object is used as a port index to the lldpXdot3LocPortTable.

The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port is compatible.

The boolean value that indicates whether the corresponding Local System VLAN name instance will be transmitted on the port defined by the given lldpXdot1LocVlanNameEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.

The table that controls selection of LLDP Protocol TLV instances to be transmitted on individual ports.

LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol instance will be transmitted. Each active lldpXdot1ConfigProtocolEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocProtocolEntry) after a re-initialization of the management system.

The value of this object is used as a port index to the lldpXdot1ConfigProtocolTable.

This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity.

The boolean value that indicates whether the corresponding Local System Protocol Identity instance will be transmitted on the port defined by the given lldpXdot1LocProtocolEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.

This table contains one row per port for IEEE 802.1 organizationally defined LLDP extension on the local system known to this agent.

Information about IEEE 802.1 organizationally defined LLDP extension.

The value of this object is used as a port index to the lldpXdot1LocTable.

The integer value used to identify the port's VLAN identifier associated with the local system. A value of zero shall be used if the system either does not know the PVID or does not support port-based VLAN operation.

This table contains one or more rows per IEEE 802.1Q VLAN name information on the local system known to this agent.

VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1LocVlanId, configured on the given port.

The value of this object is used as a port index to the lldpXdot1LocVlanNameTable.

The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port is compatible.

The string value used to identify VLAN name identified by the Vlan Id associated with the given port on the local system. This object should contain the value of the dot1QVLANStaticName object (defined in IETF RFC 2674) identified with the given lldpXdot1LocVlanId.

This table contains one or more rows per protocol identity information on the local system known to this agent.

Information about particular protocols that are accessible through the given port component. There may be multiple protocols, identified by particular lldpXdot1ProtocolIndex, and lldpLocPortNum.

The value of this object is used as a port index to the lldpXdot1LocProtocolTable.

This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity.

The octet string value used to identify the protocols associated with the given port of the local system.

This table contains one or more rows per physical network connection known to this agent. The agent may wish to ensure that only one lldpXdot1RemEntry is present for each local port, or it may choose to maintain multiple lldpXdot1RemEntries for the same local port.

Information about a particular port component.

A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The ldpXdot1RemLocalPortNum identifies the port on which the remote system information is received. The value of this object is used as a port index to the lldpRemTable.

This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the ldpXdot1RemIndex will wrap between reboots.

The integer value used to identify the port's VLAN identifier associated with the remote system. if the remote system either does not know the PVID or does not support port-based VLAN operation, the value of lldpXdot1RemPortVlanId should be zero.

This table contains one or more rows per Port and Protocol VLAN information about the remote system, received on the given port.

Port and protocol VLAN name Information about a particular port component. There may be multiple protocol VLANs, identified by a particular lldpXdot1RemProtoVlanId, configured on the remote system.

A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The ldpXdot1RemLocalPortNum identifies the port on which the remote system information is received. The value of this object is used as a port index to the lldpRemTable.

This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the ldpXdot1RemIndex will wrap between reboots.

The integer value used to identify the port and protocol VLANs associated with the given port associated with the remote system. If port and protocol VLANs are not supported on the given port associated with the remote system, or if the port is not enabled with any port and protocol VLAN, the value of lldpXdot1RemProtoVlanId should be zero.

The truth value used to indicate whether the given port (associated with the remote system) is capable of supporting port and protocol VLANs.

The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the remote system.

This table contains one or more rows per IEEE 802.1Q VLAN name information about the remote system, received on the given port.

VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1RemVlanId, received on the given port.

A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The ldpXdot1RemVlanNameLocalPortNum identifies the port on which the remote system information is received. The value of this object is used as a port index to the lldpRemTable.

This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the ldpXdot1RemVlanNameIndex will wrap between reboots.

The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port of the remote system is compatible.

The string value used to identify VLAN name identified by the VLAN Id associated with the remote system.