DES6500-SWL2MGMT-MIB: View SNMP OID List / Download MIB

VENDOR: D-LINK


 Home MIB: DES6500-SWL2MGMT-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, SW6500PRIMGMT-MIB, DLINK-ID-REC-MIB, BRIDGE-MIB, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 swL2MgmtMIB 1.3.6.1.4.1.171.11.78.1.2
The Structure of Layer 2 Network Management Information for the D-Link enterprise.
     swL2DevMgmt 1.3.6.1.4.1.171.11.78.1.2.1
         swL2DevInfo 1.3.6.1.4.1.171.11.78.1.2.1.1
             swDevInfoTotalNumOfPort 1.3.6.1.4.1.171.11.78.1.2.1.1.1 integer read-only
The number of ports within this switch. This value is the sum of the ports within this switch.
             swDevInfoNumOfPortInUse 1.3.6.1.4.1.171.11.78.1.2.1.1.2 integer read-only
The number of ports in this switch connected to the segment or the end stations.
             swDevInfoBootPromVersion 1.3.6.1.4.1.171.11.78.1.2.1.1.3 displaystring read-only
Boot Prom Version.
             swDevInfoFirmwareVersion 1.3.6.1.4.1.171.11.78.1.2.1.1.4 displaystring read-only
Firmware Version.
             swDevInfoHardwareVersion 1.3.6.1.4.1.171.11.78.1.2.1.1.5 displaystring read-only
Hardware Version.
         swL2DevCtrl 1.3.6.1.4.1.171.11.78.1.2.1.2
             swL2DevCtrlStpState 1.3.6.1.4.1.171.11.78.1.2.1.2.1 integer read-write
This object can be enabled or disabled spanning tree algorithm during runtime of the system. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevCtrlIGMPSnooping 1.3.6.1.4.1.171.11.78.1.2.1.2.2 integer read-write
This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevCtrlIGMPSnoopingMcstRTOnly 1.3.6.1.4.1.171.11.78.1.2.1.2.3 integer read-write
Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevCtrlRmonState 1.3.6.1.4.1.171.11.78.1.2.1.2.4 integer read-write
This object can be enabled or disabled RMON. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevCtrlCleanAllStatisticCounter 1.3.6.1.4.1.171.11.78.1.2.1.2.5 integer read-write
As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing. Enumeration: 'active': 2, 'normal': 1.
             swL2DevCtrlVlanIdOfFDBTbl 1.3.6.1.4.1.171.11.78.1.2.1.2.6 vlanid read-write
Indicates the VLAN ID which the Dot1dTpFdbTable belongs to ; The default value is DEFAULT_VLAN_ID of system .
             swL2DevCtrlWeb 1.3.6.1.4.1.171.11.78.1.2.1.2.14
                   swL2DevCtrlWebState 1.3.6.1.4.1.171.11.78.1.2.1.2.14.1 integer read-write
This object control web status. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                   swL2DevCtrlWebTcpPort 1.3.6.1.4.1.171.11.78.1.2.1.2.14.2 integer read-write
This object can designate tcp port. When web disable this object can't accessible.
             swL2DevCtrlTelnet 1.3.6.1.4.1.171.11.78.1.2.1.2.15
                   swL2DevCtrlTelnetState 1.3.6.1.4.1.171.11.78.1.2.1.2.15.1 integer read-write
This object control telnet status. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                   swL2DevCtrlTelnetTcpPort 1.3.6.1.4.1.171.11.78.1.2.1.2.15.2 integer read-write
This object can designate tcp port. When telnet disable this object can't accessible.
         swL2DevAlarm 1.3.6.1.4.1.171.11.78.1.2.1.3
             swL2DevAlarmNewRoot 1.3.6.1.4.1.171.11.78.1.2.1.3.1 integer read-write
When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevAlarmTopologyChange 1.3.6.1.4.1.171.11.78.1.2.1.3.2 integer read-write
This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
             swL2DevAlarmLinkChange 1.3.6.1.4.1.171.11.78.1.2.1.3.3 integer read-write
This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2PortMgmt 1.3.6.1.4.1.171.11.78.1.2.3
         swL2PortInfoTable 1.3.6.1.4.1.171.11.78.1.2.3.1 no-access
A table that contains information about every port.
             swL2PortInfoEntry 1.3.6.1.4.1.171.11.78.1.2.3.1.1 no-access
A list of information for each port of the device.
                 swL2PortInfoPortIndex 1.3.6.1.4.1.171.11.78.1.2.3.1.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module)
                 swL2PortInfoPortNumber 1.3.6.1.4.1.171.11.78.1.2.3.1.1.2 displaystring read-only
This object indicates the module's port number.
                 swL2PortInfoUnitID 1.3.6.1.4.1.171.11.78.1.2.3.1.1.3 integer read-only
Indicates ID of the unit in the system
                 swL2PortInfoType 1.3.6.1.4.1.171.11.78.1.2.3.1.1.4 integer read-only
This object indicates the connector type of this port. Enumeration: 'portType-1000Base-TX': 5, 'portType-1000Base-SX-MGBIC': 12, 'portType-1000Base-TX-GBIC': 10, 'portType-1000Base-none-MGBIC': 15, 'portType-1000Base-SX': 6, 'portType-100Base-FX': 3, 'portType-none': 1, 'portType-1000Base-none-GBIC': 11, 'portType-10G': 17, 'portType-1000Base-LX-MGBIC': 13, 'portType-1000Base-SX-GBIC': 8, 'portType-100Base-TX': 2, 'portType-100Base-FL': 4, 'portType-1000Base-none-COMBO': 19, 'portType-1000Base-LX': 7, 'portType-1000Base-TX-MGBIC': 14, 'portType-1000Base-TX-GBIC-COMBO': 18, 'portType-1000Base-LX-GBIC': 9, 'portType-SIO': 16.
                 swL2PortInfoLinkStatus 1.3.6.1.4.1.171.11.78.1.2.3.1.1.5 integer read-only
This object indicates the port link status. Enumeration: 'link-fail': 3, 'other': 1, 'error-disabled': 4, 'link-pass': 2.
                 swL2PortInfoNwayStatus 1.3.6.1.4.1.171.11.78.1.2.3.1.1.6 integer read-only
This object indicates the port speed and duplex mode. Enumeration: 'half-10Mbps': 3, 'full-1Gigabps': 8, 'full-100Mbps': 6, 'half-1Gigabps': 7, 'full-10Mbps': 4, 'other': 0, 'full-10Gigabps': 10, 'link-down': 2, 'half-10Gigabps': 9, 'half-100Mbps': 5, 'empty': 1, 'error-disabled': 11.
         swL2PortCtrlTable 1.3.6.1.4.1.171.11.78.1.2.3.2 no-access
A table that contains control information about every port.
             swL2PortCtrlEntry 1.3.6.1.4.1.171.11.78.1.2.3.2.1 no-access
A list of control information for each port of the device.
                 swL2PortCtrlPortIndex 1.3.6.1.4.1.171.11.78.1.2.3.2.1.1 integer read-only
This object indicates the module's port number.(1..Max port number in the module)
                 swL2PortCtrlUnitIndex 1.3.6.1.4.1.171.11.78.1.2.3.2.1.2 integer read-only
Indicates ID of the unit in the device
                 swL2PortCtrlAdminState 1.3.6.1.4.1.171.11.78.1.2.3.2.1.3 integer read-write
This object decide the port enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                 swL2PortCtrlNwayState 1.3.6.1.4.1.171.11.78.1.2.3.2.1.4 integer read-write
Chose the port speed, duplex mode, and N-Way function mode. Enumeration: 'nway-disabled-10Mbps-Full': 4, 'nway-disabled-1Gigabps-Full-master': 9, 'nway-enabled': 2, 'nway-disabled-1Gigabps-Full-slave': 10, 'other': 1, 'nway-disabled-100Mbps-Full': 6, 'nway-disabled-1Gigabps-Half': 7, 'nway-disabled-10Mbps-Half': 3, 'nway-disabled-100Mbps-Half': 5, 'nway-disabled-1Gigabps-Full-none': 8.
                 swL2PortCtrlFlowCtrlState 1.3.6.1.4.1.171.11.78.1.2.3.2.1.5 integer read-write
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                 swL2PortCtrlLockState 1.3.6.1.4.1.171.11.78.1.2.3.2.1.6 integer read-write
This object decide the port is locked or not. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
         swL2PortCtrlJumboFrame 1.3.6.1.4.1.171.11.78.1.2.3.3 integer read-write
This object configure the switch's jumbo frame settings. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2QOSMgmt 1.3.6.1.4.1.171.11.78.1.2.6
         swL2QOSBandwidthControlTable 1.3.6.1.4.1.171.11.78.1.2.6.1 no-access
.
             swL2QOSBandwidthControlEntry 1.3.6.1.4.1.171.11.78.1.2.6.1.1 no-access
A list of information contained in swL2QOSBandwidthControlTable.
                 swL2QOSBandwidthPortIndex 1.3.6.1.4.1.171.11.78.1.2.6.1.1.1 integer read-only
Indicates the port .
                 swL2QOSBandwidthRxRate 1.3.6.1.4.1.171.11.78.1.2.6.1.1.2 integer read-write
Indicates RX Rate(Mbit/sec) of the specifed port. Value 1000 means no limit. Value 10000 means no limit for 10G port.
                 swL2QOSBandwidthTxRate 1.3.6.1.4.1.171.11.78.1.2.6.1.1.3 integer read-write
Indicates TX Rate(Mbit/sec) of the specifed port. Value 1000 means no limit. Value 10000 means no limit for 10G port.
         swL2QOSSchedulingTable 1.3.6.1.4.1.171.11.78.1.2.6.2 no-access
.
             swL2QOSSchedulingEntry 1.3.6.1.4.1.171.11.78.1.2.6.2.1 no-access
A list of information contained in swL2QOSSchedulingTable.
                 swL2QOSSchedulingClassIndex 1.3.6.1.4.1.171.11.78.1.2.6.2.1.1 integer read-only
Indicates the hardware queue number.
                 swL2QOSSchedulingMaxPkts 1.3.6.1.4.1.171.11.78.1.2.6.2.1.2 integer read-write
Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 15 can be specified.
                 swL2QOSSchedulingMechanism 1.3.6.1.4.1.171.11.78.1.2.6.2.1.3 integer read-only
Indicates the mechanism of QOS scheduling. Enumeration: 'weightfair': 3, 'strict': 1, 'roundrobin': 2.
         swL2QOS8021pUserPriorityTable 1.3.6.1.4.1.171.11.78.1.2.6.3 no-access
.
             swL2QOS8021pUserPriorityEntry 1.3.6.1.4.1.171.11.78.1.2.6.3.1 no-access
A list of information contained in swL2QOS8021pUserPriorityTable.
                 swL2QOS8021pUserPriorityIndex 1.3.6.1.4.1.171.11.78.1.2.6.3.1.1 integer read-only
The 802.1p user priority .
                 swL2QOS8021pUserPriorityClass 1.3.6.1.4.1.171.11.78.1.2.6.3.1.2 integer read-write
The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
         swL2QOS8021pDefaultPriorityTable 1.3.6.1.4.1.171.11.78.1.2.6.4 no-access
.
             swL2QOS8021pDefaultPriorityEntry 1.3.6.1.4.1.171.11.78.1.2.6.4.1 no-access
A list of information contained in swL2QOS8021pDefaultPriorityTable.
                 swL2QOS8021pDefaultPriorityIndex 1.3.6.1.4.1.171.11.78.1.2.6.4.1.1 integer read-only
Indicates the port number .
                 swL2QOS8021pDefaultPriority 1.3.6.1.4.1.171.11.78.1.2.6.4.1.2 integer read-write
The priority value to assign to untagged packets received by the switch ports on the switch..
         swL2QOSSchedulingMechanismCtrl 1.3.6.1.4.1.171.11.78.1.2.6.5 integer read-write
This object can control QOS scheduling Mechanism. Enumeration: 'weightfair': 3, 'strict': 1, 'roundrobin': 2.
         swL2QOSHolPreventionCtrl 1.3.6.1.4.1.171.11.78.1.2.6.6 integer read-write
Control QOS Hol Prevention Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2PortSecurityMgmt 1.3.6.1.4.1.171.11.78.1.2.7
         swL2PortSecurityControlTable 1.3.6.1.4.1.171.11.78.1.2.7.1 no-access
port security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as static entry. When the learned addresses number reach N, any coming packet with not learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port.
             swL2PortSecurityControlEntry 1.3.6.1.4.1.171.11.78.1.2.7.1.1 no-access
A list of information contained in swL2PortSecurityControlTable.
                 swL2PortSecurityPortIndex 1.3.6.1.4.1.171.11.78.1.2.7.1.1.1 integer read-only
Indicates the secured port to lock address learning.
                 swL2PortSecurityMaxLernAddr 1.3.6.1.4.1.171.11.78.1.2.7.1.1.2 integer read-write
Indicates allowable number of addresses to be learned at this port.
                 swL2PortSecurityMode 1.3.6.1.4.1.171.11.78.1.2.7.1.1.3 integer read-write
Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locked address is aged out, the number of address can be learned has to be increased by one. In deleteOnReset(4) mode - never age out the locked addresses unless restart the system to prevent from port movement or intrusion. Enumeration: 'permanent': 2, 'other': 1, 'deleteOnTimeout': 3, 'deleteOnReset': 4.
                 swL2PortSecurityAdmState 1.3.6.1.4.1.171.11.78.1.2.7.1.1.4 integer read-write
Indicates administration state of locking address. Enumeration: 'enable': 2, 'other': 1, 'disable': 3.
         swL2PortSecurityDelCtrl 1.3.6.1.4.1.171.11.78.1.2.7.2
             swL2PortSecurityDelVlanName 1.3.6.1.4.1.171.11.78.1.2.7.2.1 displaystring read-write
Indicates vlan name.
             swL2PortSecurityDelPort 1.3.6.1.4.1.171.11.78.1.2.7.2.2 integer read-write
Indicates the port.
             swL2PortSecurityDelMacAddress 1.3.6.1.4.1.171.11.78.1.2.7.2.3 macaddress read-write
Specifies MAC address.
             swL2PortSecurityDelActivity 1.3.6.1.4.1.171.11.78.1.2.7.2.4 integer read-write
. Enumeration: 'start': 2, 'none': 1.
     swL2TrunkMgmt 1.3.6.1.4.1.171.11.78.1.2.9
         swL2TrunkMaxSupportedEntries 1.3.6.1.4.1.171.11.78.1.2.9.1 integer read-only
Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
         swL2TrunkCurrentNumEntries 1.3.6.1.4.1.171.11.78.1.2.9.2 integer read-only
Current actived number of entries in the trunk configuration table.
         swL2TrunkCtrlTable 1.3.6.1.4.1.171.11.78.1.2.9.3 no-access
This table specifys which ports group a set of ports(up to 8) into a single logical link.
             swL2TrunkCtrlEntry 1.3.6.1.4.1.171.11.78.1.2.9.3.1 no-access
A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
                 swL2TrunkIndex 1.3.6.1.4.1.171.11.78.1.2.9.3.1.1 integer read-only
The index of logical port trunk. The trunk group number depend on the existence of unit and module.
                 swL2TrunkName 1.3.6.1.4.1.171.11.78.1.2.9.3.1.2 displaystring read-only
The name of logical port trunk.
                 swL2TrunkMasterPort 1.3.6.1.4.1.171.11.78.1.2.9.3.1.3 integer read-only
The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
                 swL2TrunkMember 1.3.6.1.4.1.171.11.78.1.2.9.3.1.4 portlist read-only
Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 8 for one trunks.
                 swL2TrunkFloodingPort 1.3.6.1.4.1.171.11.78.1.2.9.3.1.5 integer read-only
The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.
                 swL2TrunkType 1.3.6.1.4.1.171.11.78.1.2.9.3.1.6 integer read-only
This object indicated that type of the trunk group. static : is static trunk group lacp : is LACP trunk group . Enumeration: 'lacp': 3, 'other': 1, 'static': 2.
                 swL2TrunkState 1.3.6.1.4.1.171.11.78.1.2.9.3.1.7 rowstatus read-only
This object indicates the status of this entry.
         swL2TrunkAlgorithm 1.3.6.1.4.1.171.11.78.1.2.9.4 integer read-write
This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. Enumeration: 'ip-source': 5, 'mac-destination': 3, 'mac-source': 2, 'mac-source-dest': 4, 'ip-source-dest': 7, 'ip-destination': 6, 'other': 1.
         swL2TrunkLACPPortTable 1.3.6.1.4.1.171.11.78.1.2.9.5 no-access
This table specifys which ports group a set of ports(up to 8) into a single logical link.
             swL2TrunkLACPPortEntry 1.3.6.1.4.1.171.11.78.1.2.9.5.1 no-access
A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
                 swL2TrunkLACPPortIndex 1.3.6.1.4.1.171.11.78.1.2.9.5.1.1 integer read-only
The index of logical port lacp.
                 swL2TrunkLACPPortState 1.3.6.1.4.1.171.11.78.1.2.9.5.1.2 integer read-write
The state of logical port lacp. Enumeration: 'active': 1, 'passive': 2.
     swL2MirrorMgmt 1.3.6.1.4.1.171.11.78.1.2.10
           swL2MirrorLogicTargetPort 1.3.6.1.4.1.171.11.78.1.2.10.1 integer read-write
This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.
           swL2MirrorPortSourceIngress 1.3.6.1.4.1.171.11.78.1.2.10.2 portlist read-write
The represent the ingress into the source port packet to sniffed.
           swL2MirrorPortSourceEgress 1.3.6.1.4.1.171.11.78.1.2.10.3 portlist read-write
The represent the egress from the source port packet to sniffed.
           swL2MirrorPortState 1.3.6.1.4.1.171.11.78.1.2.10.4 integer read-write
This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - writing this value to the object, and then the corresponding entry will be removed from the table. enabled(3) - this entry is reside in the table. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
     swL2IGMPSnoopingMgmt 1.3.6.1.4.1.171.11.78.1.2.11
           swL2IGMPSnoopingMaxSupportedVlans 1.3.6.1.4.1.171.11.78.1.2.11.1 integer read-only
Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPSnoopingCtrlTable).
           swL2IGMPSnoopingMaxIpGroupNumPerVlan 1.3.6.1.4.1.171.11.78.1.2.11.2 integer read-only
Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPSnoopingQueryInfoTable).
           swL2IGMPSnoopingCtrlTable 1.3.6.1.4.1.171.11.78.1.2.11.3 no-access
The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12.
               swL2IGMPSnoopingCtrlEntry 1.3.6.1.4.1.171.11.78.1.2.11.3.1 no-access
The entry in IGMP control table (swL2IGMPSnoopingCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
                   swL2IGMPSnoopingCtrlVid 1.3.6.1.4.1.171.11.78.1.2.11.3.1.1 integer read-only
This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.
                   swL2IGMPSnoopingQueryInterval 1.3.6.1.4.1.171.11.78.1.2.11.3.1.2 integer read-write
The frequency at which IGMP Host-Query packets are transmitted on this switch.
                   swL2IGMPSnoopingMaxResponseTime 1.3.6.1.4.1.171.11.78.1.2.11.3.1.3 integer read-write
The maximum query response time on this switch.
                   swL2IGMPSnoopingRobustness 1.3.6.1.4.1.171.11.78.1.2.11.3.1.4 integer read-write
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
                   swL2IGMPSnoopingLastMemberQueryInterval 1.3.6.1.4.1.171.11.78.1.2.11.3.1.5 integer read-write
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
                   swL2IGMPSnoopingHostTimeout 1.3.6.1.4.1.171.11.78.1.2.11.3.1.6 integer read-write
The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.
                   swL2IGMPSnoopingRouteTimeout 1.3.6.1.4.1.171.11.78.1.2.11.3.1.7 integer read-write
The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
                   swL2IGMPSnoopingLeaveTimer 1.3.6.1.4.1.171.11.78.1.2.11.3.1.8 integer read-write
When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
                   swL2IGMPSnoopingQueryState 1.3.6.1.4.1.171.11.78.1.2.11.3.1.9 integer read-write
This object decide the IGMP query enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.
                   swL2IGMPSnoopingCurrentState 1.3.6.1.4.1.171.11.78.1.2.11.3.1.10 integer read-only
This object indicates the current IGMP query state. Enumeration: 'non-querier': 3, 'other': 1, 'querier': 2.
                   swL2IGMPSnoopingCtrlState 1.3.6.1.4.1.171.11.78.1.2.11.3.1.11 integer read-write
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry. Enumeration: 'enable': 3, 'other': 1, 'disable': 2.
           swL2IGMPSnoopingQueryInfoTable 1.3.6.1.4.1.171.11.78.1.2.11.4 no-access
The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.
               swL2IGMPSnoopingQueryInfoEntry 1.3.6.1.4.1.171.11.78.1.2.11.4.1 no-access
Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPSnoopingCtrState of associated VLAN entry are all enabled.
                   swL2IGMPSnoopingInfoVid 1.3.6.1.4.1.171.11.78.1.2.11.4.1.1 integer read-only
This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPSnoopingCtrlVid in the associated entry of IGMP control table (swL2IGMPSnoopingCtrlTable).
                   swL2IGMPSnoopingInfoQueryCount 1.3.6.1.4.1.171.11.78.1.2.11.4.1.2 integer read-only
This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.
                   swL2IGMPSnoopingInfoTxQueryCount 1.3.6.1.4.1.171.11.78.1.2.11.4.1.3 integer read-only
This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
           swL2IGMPSnoopingInfoTable 1.3.6.1.4.1.171.11.78.1.2.11.5 no-access
The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also.
               swL2IGMPSnoopingInfoEntry 1.3.6.1.4.1.171.11.78.1.2.11.5.1 no-access
Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnoopingSnooping and swL2IGMPSnoopingCtrlState of associated VLAN entry are all enabled.
                   swL2IGMPSnoopingVid 1.3.6.1.4.1.171.11.78.1.2.11.5.1.1 integer read-only
This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.
                   swL2IGMPSnoopingGroupIpAddr 1.3.6.1.4.1.171.11.78.1.2.11.5.1.2 ipaddress read-only
This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.
                   swL2IGMPSnoopingMacAddr 1.3.6.1.4.1.171.11.78.1.2.11.5.1.3 macaddress read-only
This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.
                   swL2IGMPSnoopingPortMap 1.3.6.1.4.1.171.11.78.1.2.11.5.1.4 portlist read-only
This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero.
                   swL2IGMPSnoopingIpGroupReportCount 1.3.6.1.4.1.171.11.78.1.2.11.5.1.5 integer read-only
This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.
     swL2TrafficMgmt 1.3.6.1.4.1.171.11.78.1.2.13
     swL2TrafficSegMgmt 1.3.6.1.4.1.171.11.78.1.2.14
           swL2TrafficSegTable 1.3.6.1.4.1.171.11.78.1.2.14.1 no-access
This table specifys the port just can forward traffic to the specific port list.
               swL2TrafficSegEntry 1.3.6.1.4.1.171.11.78.1.2.14.1.1 no-access
A list of information specifies the port with its traffic forward list.
                   swL2TrafficSegPort 1.3.6.1.4.1.171.11.78.1.2.14.1.1.1 integer read-only
The port number of the logical port.
                   swL2TrafficSegForwardPorts 1.3.6.1.4.1.171.11.78.1.2.14.1.1.2 portlist read-write
The port list that the specific port can forward traffic.
     swL2MgmtMIBTraps 1.3.6.1.4.1.171.11.78.1.2.15
           swL2Notify 1.3.6.1.4.1.171.11.78.1.2.15.1
               swL2NotifyPrefix 1.3.6.1.4.1.171.11.78.1.2.15.1.2
                   swL2NotifFirmware 1.3.6.1.4.1.171.11.78.1.2.15.1.2.0
     swL2RstpMgmt 1.3.6.1.4.1.171.11.78.1.2.16