DES3010FL-L2MGMT-MIB: View SNMP OID List / Download MIB

The Structure of Common Management Information for making a trunk and IGMP related function for D-Link devices.

This object is a set of system LED indications. The two octets is defined as system LED. The first LED is power LED. The second LED is console LED. The other octets following the second octets are the logical port LED (following dot1dBasePort ordering). Every two bytes are presented to a port. The first byte is presentd to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.

This object indicates the module type. Enumeration: 'none': 0, 'moduleType-COMBA': 4, 'moduleType-DEM-301G': 3, 'moduleType-DEM-201F': 2, 'moduleType-DEM-201FL': 5, 'moduleType-DEM-301T': 1.

This object indicates the module type. Enumeration: 'none': 0, 'moduleType-COMBA': 4, 'moduleType-DEM-301G': 3, 'moduleType-DEM-201F': 2, 'moduleType-DEM-201FL': 5, 'moduleType-DEM-301T': 1.

This object indicates the agent system reboot state. The agent always returns other(1) when this object is read. Enumeration: 'reboot-and-load-factory-default-config': 4, 'other': 1, 'reboot': 2, 'save-config-and-reboot': 3.

This object indicates system ip.

This object indicates system subnet mask.

This object indicates system default gateway.

This object controls which Vlan includes system ip. And the Vlan should have been created.

This object can be enabled or disabled spanning tree algorithm during runtime of the system. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled . Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing. Enumeration: 'active': 2, 'normal': 1.

Indicates whether the SNMP entity is permitted to generate authenticationFailure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authenticationFailure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant across re-initializations of the network management system. Enumeration: 'disabled': 2, 'enabled': 1.

This object can be enabled or disabled RMON. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

Indicates the status of automatically getting configuration from TFTP server on device Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

This object decide the multicast packets filtering mode on all port . Enumeration: 'forward-unregistered-groups': 2, 'filter-unregistered-groups': 3.

This object can enabled or disabled MAC Notification. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

This object indicates the history size of variation MAC in address table. The default value is 1 .

This object indicates the time interval in second for trigger the MAC notify message.

This indicates the global state of the VLAN trunking feature of the device. Enumeration: 'disabled': 2, 'enabled': 1.

Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For receiving LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table. Enumeration: 'disabled': 2, 'enabled': 1.

When lldp is disabled and lldp forward_message's are enabled, the LLDP Data Unit packets received by the switch will be forwarded. Enumeration: 'disabled': 2, 'enabled': 1.

Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT_VLAN_ID of the system.

Time scale is 5 seconds.The value will be between 0%(idle) and 100% (very busy).

Time scale is 1 minute.The value will be between 0%(idle) and 100% (very busy).

Time scale is 5 minute.The value will be between 0%(idle) and 100% (very busy).

This object determines whether or not to send a trap message when the link changes. If the object is enabled (3), the Link Change trap is sent by the device when any of its port links change. The device does not send the trap if this object value is disabled or in another state. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

A table that contains information about every port.

A list of information for each port of the device.

This object indicates the module's port number.(1..Max port number in the module)

This object indicates the port link status. Enumeration: 'link-fail': 3, 'other': 1, 'link-pass': 2.

This object indicates the port speed and duplex mode. Enumeration: 'half-10Mbps-backp': 4, 'half-100Mbps-backp': 8, 'full-100Mbps-none': 7, 'full-1Gigabps-none': 11, 'auto': 1, 'full-10Mbps-8023x': 2, 'half-100Mbps-none': 9, 'full-100Mbps-8023x': 6, 'half-1Gigabps-none': 13, 'full-10Mbps-none': 3, 'half-1Gigabps-backp': 12, 'half-10Mbps-none': 5, 'full-1Gigabps-8023x': 10.

A table that contains control information about every port.

A list of control information for each port of the device.

This object indicates the module's port number.(1..Max port number in the module)

This object decide the port enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

Chose the port speed, duplex mode, and N-Way function mode. Enumeration: 'nway-disabled-1Gigabps-Full': 7, 'nway-disabled-10Mbps-Full': 3, 'nway-disabled-100Mbps-Full': 5, 'nway-auto': 1, 'nway-disabled-10Mbps-Half': 2, 'nway-disabled-100Mbps-Half': 4.

Set flow control function as enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

The object describe the ports in text.

This object set each poet MAC notification state. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

This object controls the MDIX state of a specified port. Enumeration: 'auto': 1, 'cross': 3, 'normal': 2.

A table that contains information about Err port.

A list of information for err port of the device.

This object indicates the module's port number.(1..Max port number in the module)

This object decide the portstate enabled or disabled. Enumeration: 'disabled': 1, 'enabled': 2.

This object decide the PortStatus whether err-disabled. Enumeration: 'other': 1, 'err-disabled': 2.

This object decide the PortStatus STP LBD or Storm control. Enumeration: 'stp-lbd': 1, 'storm-control': 2.

The object describe the ports in text.

.

A list of information contained in swL2QOSBandwidthControlTable.

Indicates the port .

Indicates RX Rate(Kbit/sec) of the specifed port.Value 1024000 means no limit.

Indicates TX Rate(Kbit/sec) of the specifed port.Value 1024000 means no limit.

The RxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured RxRate.

The TxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured TxRate.

.

A list of information contained in swL2QOSSchedulingTable.

Indicates the hardware queue number.

.

A list of information contained in swL2QOS8021pUserPriorityTable.

The 802.1p user priority .

The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).

.

A list of information contained in swL2QOS8021pDefaultPriorityTable.

Indicates the port number .

The priority value to assign to untagged packets received by the switch ports on the switch..

The value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.

This object can control QOS scheduling Mechanism. Enumeration: 'weightfair': 2, 'strict': 1, 'none': 3.

The max entries of swPortTrunkTable

The max number of ports allowed in a trunk.

This table specifies the port membership for each logical link.

A list of information specifies which ports group form a single logical link.

The index of logical port trunk.

The object indicates the master port number of the port trunk entry.The first port of the trunk is implicitly configured to be the master logical port.When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).

Indicate member ports of a logical trunk.

This object indicates the type of this entry. Enumeration: 'lacp': 2, 'static': 1.

This object indicates the active ports of this entry.

This object indicates the status of this entry. when the state is CreatAndGo(4),the type of trunk is static(1); when the state is CreatAndWait(5),the type of trunk is lacp(2).

The flooding port of every trunk.

This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. Enumeration: 'other': 1, 'mac-source-dest': 4, 'mac-source': 2, 'mac-destination': 3.

This table specifys which ports group a set of ports(up to 8) into a single logical link.

A list of information specifies which ports group a set of ports(up to 8) into a single logical link.

The index of logical port lacp.

The state of logical port lacp. Enumeration: 'active': 1, 'passive': 2.

This table is used to manage the VLAN trunking feature of the device.

This object is used to configure the VLAN trunking settings for each port.

This object indicates the port being configured.

The state of the logical port LACP. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates the Rx port list of ports to be sniffed.

This object indicates the Tx port list of ports to be sniffed.

This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.

This object indicates the status of this entry. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable).

Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).

The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12.

The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.

This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.

The frequency at which IGMP Host-Query packets are transmitted on this switch.

The maximum query response time on this switch.

The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.

The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.

The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.

The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.

When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.

This object decide the IGMP query enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

This object indicates the current IGMP query state. Enumeration: 'non-querier': 3, 'other': 1, 'querier': 2.

This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry. Enumeration: 'enable': 3, 'other': 1, 'disable': 2.

Enumeration: 'enable': 3, 'other': 1, 'disable': 2.

The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.

Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.

This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).

This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.

This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.

The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also.

Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.

This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.

This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.

This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.

This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero.

This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.

The information of the router port table.

The entry of swL2IGMPRouterPortTable.

This object indicates the vlan id of the router port entry.

This object indicates the vlan name of the router port entry.

This object indicate the static portlist of the router port entry.

This object indicate the dynamic portlist of the router port entry.

This object indicate the forbidden portlist of the router port entry.

This table is used to manage the IGMP Access Authentication configurations of the device.

A list of manageable entities for IGMP Access Authentication. The configuration is done per port.

The index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.

This object denotes the status of IGMP Access Authentication of the port. Enumeration: 'enable': 3, 'other': 1, 'disable': 2.

This table specifys the storm traffic control configuration.

A list of information specifies the storm traffic control configuration.

The index of logical port trunk. The trunk group number depend on the existence of unit and module.

Indicates ID of the unit in the device

This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl, swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlUcastStromCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured amount of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet.

This object indicates broadcast storm control function is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

This object indicates multicast storm control function is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

This object indicates destination lookup fail function is enabled or disabled. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

This table specifys the port just can forward traffic to the specific port list.

A list of information specifies the port with its traffic forward list.

The port number of the logical port.

The port list that the specific port can forward traffic.

port security feature which controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as static entry. When the learned addresses number reach N, any coming packet with not learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port.

A list of information contained in swL2PortSecurityControlTable.

Indicates the secured port to lock address learning.

Indicates allowable number of addresses to be learned at this port.

Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locked address is aged out, the number of address can be learned has to be increased by one. In deleteOnReset(4) mode - never age out the locked addresses unless restart the system to prevent from port movement or intrusion. Enumeration: 'permanent': 2, 'deleteOnTimeout': 3, 'other': 1, 'deleteOnReset': 4.

Indicates administration state of locking address. Enumeration: 'enable': 2, 'other': 1, 'disable': 3.

when enable(2),whenever there's a new MAC that violates the pre-defined port security configuration, trap will be sent out and the relevant information will be logged in system. Enumeration: 'enable': 2, 'other': 1, 'disable': 3.

Indicates whether flooding BPDU packets when STP is disabled on device Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

Indicates whether STP loop-back prevent on the device is turned on Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

The period of time on which STP module keeps checking the BPDU loop status, to configure swL2StpLbdRecoverTime as 0 disables automatically recover

A table that contains port-specific information for the Spanning Tree Protocol.

A list of information maintained by every port about the Spanning Tree Protocol state for that port.

The port number of the port for this entry.

The enabled/disabled status is used to Loop-back prevention attached to this port. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

When the port Enable state is enabled, the port's current state as defined by application of the Spanning Tree Protocol. If the PortEnable is disabled, the the port status will be no-stp-enabled(7). If the port is in error disabled status, the port status will be err-disabled(8) Enumeration: 'err-disabled': 8, 'discarding': 3, 'disabled': 2, 'broken': 6, 'no-stp-enabled': 7, 'learning': 4, 'forwarding': 5, 'other': 1.

When the port Enable state is enabled, the port's current port role as defined by application of the Spanning Tree Protocol. If the Port Enable state is disabled, the the port role will be nonstp(7). If the port is in loop-back status, the port role will be loopback(8) Enumeration: 'loopback': 7, 'root': 4, 'alternate': 2, 'designated': 5, 'disabled': 1, 'nonStp': 6, 'backup': 3.

The enabled/disabled status is used to BPDU Filtering attached to this port. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

This object indicates the stp port speed and duplex mode. Enumeration: 'half-10Mbps-backp': 3, 'half-100Mbps-backp': 7, 'full-100Mbps-none': 8, 'full-1000Mbps-8023x': 13, 'full-10Mbps-8023x': 5, 'full-1000Mbps-none': 12, 'half-100Mbps-none': 6, 'full-100Mbps-8023x': 9, 'half-1000Mbps-none': 10, 'full-10Mbps-none': 4, 'half-10Mbps-none': 2, 'link-down': 1, 'full-1000Mbps-backp': 11.

When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.

The administrative value of the Edge Port parameter. A value of TRUE(0) indicates that this port should be assumed as an edge-port and a value of FALSE(1) indicates that this port should be assumed as a non-edge-port. Enumeration: 'forceTrue': 0, 'forceFalse': 1, 'auto': 2.

The operational value of the Edge Port parameter. The object is initialized to the value of swL2StpPortAdminEdgePort and is set FALSE on reception of a BPDU.

The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means. Enumeration: 'forceTrue': 0, 'forceFalse': 1, 'auto': 2.

The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the swL2StpPortAdminPointToPoint object.

The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object swL2StpPortPathCost, which returns the operational value of the path cost. Issue No.: 3250R2-077 As USE_RSTP is 1:enabled, swL2StpPortPathCost is forced to be read-only. configuration via swL2StpPortAdminPathCost. According 802.1w, value range of swL2StpPortAdminPathCost would be expanded. the former value range is (0..65535), the new is (0..200000000).

The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of swL2StpPort.

The enabled/disabled status is usedoop-back prevention attached to this port. Enumeration: 'disabled': 2, 'other': 1, 'enabled': 3.

If TRUE causes the port not to be selected as Root Port, even it has the best spanning tree priotiry vector.

If TRUE causes the port not to propagate received topology change notifications and topology changes to other Ports.

Used to show and config per port priority-based QoS features on the switch

A list of information contained in swL2CosPriorityTable.

The port number of CoS Priority.

Indicates port_priority state for CoS. Enumeration: 'enable': 3, 'other': 1, 'disable': 2.

Enable Ethernet frame based priority. When set ether8021p(2), enable 802.1p QoS; When set macBase(3), enable MAC-based QoS; When set disable(1), disable Ethernet frame based priority. Enumeration: 'disable': 1, 'macBase': 3, 'ether8021p': 2.

Enable IP priority QoS. When set tos(2), enable TOS based QoS; When set dscp(3), enable DSCP based QoS; When set disable(1), disable IP priority QoS. Enumeration: 'tos': 2, 'disable': 1, 'dscp': 3.

when read,it always return invalid(2); when write valid(1),it disables all priority in this table. Enumeration: 'valid': 1, 'invalid': 2.

Used to show port-to-class mappings and map specific port to one of the hardware queues available on the switch.

A list of information contained in swL2CosPortPRITable.

Indicates CoS Priority PortPRI.

The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges. And you can set value only 0 or 3,you can't set value 1 or 2.

Used to show MAC priority map to traffic class and map the destination MAC address in incoming packet to one of the hardware queues available on the switch.

A list of information contained in swL2CosMacBasePRITable.

Indicates CoS Priority MacBasePRI.

The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges.

Used to show TOS value to traffic class mapping and map the TOS value in the IP header of incoming packet to one of the four hardware queues available on the switch.

A list of information contained in swL2CosTosPRITable.

Indicates CoS Priority TosPRI.

The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges.

Used to show DSCP value to traffic class mapping and map the DSCP value in the IP header of incoming packet to one of the hardware queues available on the switch.

A list of information contained in swL2CosDscpPRITable.

Indicates CoS Priority DscpPRI.

The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set, You must have administrator privileges.

This object indicates the loopback detection status for the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates the interval value, the range is from 1 to 32767 seconds.

This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.

The table specifies the loopback detection function specified by port.

The table specifies the loopback detection function specified by port.

This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module

This object indicates the loopback detection function state on the port. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates the port status. Enumeration: 'normal': 1, 'loop': 2, 'error': 3.

A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.

Static information for a VLAN configured into the device by (local or network) management.

The VLAN ID of the VLAN to be created. The range is 1 - 4094.

The name of the VLAN to be displayed.

The type of the VLAN to be displayed. Enumeration: 'dynamic': 0, 'static': 1.

A range of member ports to the VLAN.

A range of static ports to the VLAN.

Specifies the additional ports as untagged.

Specifies the additional ports as tagged.

This trap indicates the MAC addresses variation in address table .

When the port_security trap is enabled, new MAC addresses that violate the pre-defined port security configuration will trigger trap messages to be sent out.

This object indicates the last time reboot information.

This object indicates the MAC address that violates the port security configuration.