DES-1210-28-AXME: View SNMP OID List / Download MIB

System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) ' + - = .

Version number of the Hardware.

Version number of the Firmware.

This time interval is used to count the time and logout web interface automatically.

The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.

Group Interval is used to send D-link Discover packet to D-link SmartConsole Utility frequency. The timer in units of seconds. Set value 0 to disable group Interval.

This object is used to set Safeguard Enable\Disable. Enumeration: 'enable': 1, 'disable': 2.

This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'.

This object is used to save Configuration.

A table to control the port specific parameters of the device like speed, duplex mode, etc.

An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.

Interface index of the port for the configuration in this entry applies.

This object indicates the port type: fiber 1G/100M or copper. Enumeration: 'copper': 100, 'fiber100M': 102, 'fiber1G': 101.

Configures interface speed. Enumeration: 'rate100M-Half': 3, 'auto': 6, 'rate1000M-Full': 1, 'rate10M-Full': 4, 'disable': 7, 'rate10M-Half': 5, 'rate100M-Full': 2.

The port's operating speed state. Enumeration: 'rate10M-Full': 5, 'rate100M-Half': 4, 'rate1000M-Full': 2, 'down': 1, 'rate10M-Half': 6, 'rate100M-Full': 3.

Configures interface auto/mdi/mdix mode. The default setting is Auto. Enumeration: 'auto': 1, 'mdi': 2, 'mdix': 3.

Enables / disables flow control for the interface. Enumeration: 'enable': 1, 'disable': 2.

The link parner negotiate port's operating flow control state. Enumeration: 'disabled': 2, 'enabled': 1.

The port's media type. Enumeration: 'fiberwith100BaseSFPModule': 3, 'gigabitethernet': 2, 'fiberwith1000BaseSFPModule': 4, 'fastethernet': 1.

The port description table.

The port description entry.

This object indicates the port index.

This object indicates the port type: fiber 1G/100M or copper. Enumeration: 'copper': 100, 'fiber100M': 102, 'fiber1G': 101.

This object indicates the port description.

The port error table.

A list of information for the err port of the device.

This object indicates the module's port number.(1..Max port number in the module)

This object decides whether the port state is enabled or disabled. Enumeration: 'disabled': 1, 'enabled': 2.

This object decides whether the PortStatus is err-disabled. Enumeration: 'other': 1, 'err-disabled': 2.

This object decides whether the PortStatus is LBD. Enumeration: 'lbd': 1.

This object indicates auto config is enabled or disabled. Enumeration: 'enable': 1, 'disable': 2.

This object is for Enabled(1) or Disabled(2) Web state in the system. Enumeration: 'disabled': 2, 'enabled': 1.

Web Server Port Number.

This object is for ARP aging time.

This object is for MAC aging time.

Enable/Disable management Telnetsetting mechanism. Enumeration: 'disabled': 2, 'enabled': 1.

The value is for setting telnet's UDP Port.

To set the WEB panel auto refresh timer. Enumeration: 'refreshtime1min': 3, 'refreshtime5mins': 4, 'refreshtime30secs': 2, 'refreshimenever': 0, 'refreshtime10secs': 1.

Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system. Enumeration: 'dynamic': 2, 'manual': 1.

Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.

IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.

Gateway

Status of DHCP Option12 Enumeration: 'enable': 1, 'disable': 2.

Host name in DHCP option 12

The TFTP server's IP address is used to upload or download firmware.

Configure firmware filename to download.

The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName. Enumeration: 'download': 1, 'none': 0, 'upload': 2.

The tftp operation status represent firmware backup or upgrade status. Enumeration: 'fail': 2, 'transmit': 4, 'none': 0, 'progressing': 3, 'success': 1.

The TFTP server's IP address is used to upload or download configuration file.

The configuration filename is used to store or retrieve config from the tftp server.

The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName. Enumeration: 'download': 1, 'progressing': 3, 'upload': 2.

The tftp operation status represent configuration file backup or restore status. Enumeration: 'fail': 2, 'none': 0, 'progressing': 3, 'success': 1.

Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing. Enumeration: 'reset': 1, 'noop': 2.

Resets the units statistics. A (1) resets the statistics count, a (2) does nothing. Enumeration: 'reset': 1, 'noop': 2.

This object is for enabling or disabling SNMP Community function. Enumeration: 'disabled': 2, 'enabled': 1.

A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.

A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID. Enumeration: 'v2c': 2, 'v1': 1, 'v3': 3.

The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.

An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of UserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoAuthProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoAuthProtocol, then an 'inconsistentValue' error must be returned. If a set operation tries to set the value to the NoAuthProtocol while the UserPrivProtocol value in the same row is not equal to NoPrivProtocol, then an 'inconsistentValue' error must be returned. That means that an SNMP command generator application must first ensure that the UserPrivProtocol is set to the NoPrivProtocol value before it can set the UserAuthProtocol value to NoAuthProtocol. Enumeration: 'sha': 3, 'none': 1, 'md5': 2.

An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of usmUserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoPrivProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoPrivProtocol, then an 'inconsistentValue' error must be returned. Note that if any privacy protocol is used, then you must also use an authentication protocol. In other words, if usmUserPrivProtocol is set to anything else than NoPrivProtocol, then the corresponding instance of usmUserAuthProtocol cannot have a value of usmNoAuthProtocol. If it does, then an 'inconsistentValue' error must be returned. Enumeration: 'none': 1, 'des': 2.

The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified, except for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active.

The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.

In order to gain the access rights allowed by this conceptual row, this securityModel must be in use. Enumeration: 'v2c': 2, 'v1': 1, 'v3': 3.

The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If multiple entries are equally indexed except for this vacmAccessSecurityLevel index, then the entry which has the highest value for vacmAccessSecurityLevel is selected.

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.

The human readable name for a family of view subtrees.

The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees.

The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub-identifier of vacmViewTreeFamilySubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if, for each sub-identifier of the value of vacmViewTreeFamilySubtree, either: the i-th bit of vacmViewTreeFamilyMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of vacmViewTreeFamilySubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of vacmViewTreeFamilySubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of vacmViewTreeFamilySubtree. Note that masks of length greater than zero length do not need to be supported. In this case this object is made read-only.

Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or excluded from the MIB view. Enumeration: 'included': 1, 'excluded': 2.

The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.

The unique index value of a row in this table.

A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format.

The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpCommunityName and snmpCommunitySecurityName objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpCommunityStatus is active(1).

This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.

The locally arbitrary.

The Level of Security to be used when generating SNMP messages using this entry. Enumeration: 'v2c': 2, 'v1': 1, 'v3NoAuthNoPriv': 3, 'v3AuthNoPriv': 4, 'v3AuthPriv': 5.

An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the value of the snmpEngineID of a remote SNMP engine with which this user can communicate.

This object is for enabling or disabling SNMP login fail event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling devie Bootup event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling Fiber link up / link down event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling Copper link up / link down event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling RSTP topology change event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

This object is for enabling or disabling Firmware upgrade suess or fail event trap in the system. Enumeration: 'disabled': 2, 'enabled': 1.

The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start. Enumeration: 'disabled': 2, 'enabled': 1.

The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w and 'mstp(3)' indicates the Multiple Spanning Tree Protocol Specified in IEEE 802.1s. Enumeration: 'mstp': 3, 'stp': 0, 'rstp': 2.

The Value of the writable portion of the Bridge Identifier comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.

The value used by the Port Transmit state machine to limit the maximum transmission rate.

The value that all bridges use for MaxAge when this bridge is acting as the root. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.

The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D specifies that the range for this parameter is related to the value of BridgeMaxAge. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

This object is for enabling or disabling forward BPDU. Enumeration: 'disabled': 2, 'enabled': 1.

The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Root Identifier parameter in all Configuration Bridge PDUs originated by this node.

The Cost of the path to the CIST Root as seen from this bridge.

The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.

This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in a particular state before moving to the next state.

The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge.

A table that contains port-specific information for the Spanning Tree Protocol.

A list of information maintained by every port about the Spanning Tree Protocol state for that port.

The Port number of the port for which this entry contains spanning tree information.

Current state of the Port which can be changed to either Disabled or Enabled for ALL spanning tree instances. Setting this object will override the port's status in any of the MSTI contexts Enumeration: 'disabled': 0, 'enabled': 1.

The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting the CistPortPriority value. The values that are set for Port Priority must be in steps of 16.

The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object stpPortPathCost. If the default Path Cost is being used,this object returns '0' when read.

The contribution of this port to the path cost of paths towards the CIST Root which include this port.

Indicates the Protocol migration state of this Port. When operating in RSTP/MSTP (version >= 2) mode, writing TRUE(1) to this object forces this port to transmit MSTP BPDUs without instance information. Any other operation on this object has no effect and it always returns FALSE(2) when read.

This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled. Enumeration: 'false': 0, 'true': 1, 'auto': 2.

The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means. Enumeration: 'forceFalse': 1, 'forceTrue': 0, 'auto': 2.

A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'.

A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC-Operational for the attached LANs transitions frequently.

The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.

Current state of the Port as defined by the Common spanning tree protocol. Enumeration: 'disabled': 1, 'discarding': 2, 'forwarding': 5, 'learning': 4.

This object is for enabling or disabling forward BPDU. Enumeration: 'disabled': 2, 'enabled': 1.

The Name for the Region's configuration. By Default Region Name will be equal to the Bridge Mac Address.

Version of the MST Region.

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

This table contains one entry for each instance of MSTP. This table maintains context ID as one more index to support Multiple Instances.

A conceptual row containing the status of the MSTP instance.

An arbitrary integer within the range from 1 to the value of Max Instance Number that uniquely identifies an instance.

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values.

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to unmap from this Instance. A vlan may not be unmapped from this instance if it is not already mapped to this Instance. This object is used only for SET operation.GET Operation returns null values.

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.

The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start. Enumeration: 'disabled': 2, 'enabled': 1.

Table containing Bridge Information specific to Spanning Tree Instance. This table maintains context ID as one more index to support Multiple Instances.

Entry indicating the Bridge Information.

Spanning Tree Instance to which the information belongs.

The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.

The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start. Enumeration: 'disabled': 2, 'enabled': 1.

This table contains Common Spanning Tree Port Information.

A list of information maintained by every port for Common Spanning tree.

The Port number of the port for which this entry contains spanning tree information.

The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.

Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port Enumeration: 'disabled': 0, 'enabled': 1.

Current Port Role of the port for this spanning tree instance. Enumeration: 'backup': 2, 'alternate': 1, 'designated': 4, 'disabled': 0, 'master': 5, 'root': 3.

This table contains Spanning Tree Instance Specific Port Information.

A list of information maintained by every port for each and every spanning tree instance.

The Port number of the port for which this entry contains spanning tree information.

The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.

Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port Enumeration: 'disabled': 0, 'enabled': 1.

Current Port Role of the port for this spanning tree instance. Enumeration: 'backup': 2, 'alternate': 1, 'designated': 4, 'disabled': 0, 'master': 5, 'root': 3.

Enable/Disable management VLAN mechanism. Enumeration: 'disabled': 2, 'enabled': 1.

The management VLAN ID, which will allow to forward packets of that VLAN to CPU.

Enable/Disable IEEE 802.1Q Asymmetric VLAN Enumeration: 'disabled': 2, 'enabled': 1.

A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.

Information for a VLAN configured into the device by (local or network) management.

An administratively assigned string, which may be used to identify the VLAN.

The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed.

The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port per-VLAN Registrar control for Registration Forbidden for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanEgressPorts. The default value of this object is a string of zeros of appropriate length, excluding all ports from the forbidden set.

The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option.

Enable/Disable Advertisement Status of the IEEE 802.1Q VLAN. Enumeration: 'disabled': 2, 'enabled': 1.

The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard.

This table contains the list of ports through which a router, in a particular VLAN is reachable.

A list of multicast filter mode information for each VLAN ID.

Per Vlan to configure multicast filtering function.

Filter unknown multicast frames or normal operation(i.e. forwarding) Enumeration: 'filter': 1, 'forward': 0.

Sets the Link Aggregation Module administrative status as enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel.

There is one entry in this table for each created port-channel port.

The index of the port-channel(Aggregator's interface index).

Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel.

Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled.

The master port of the port-channel.

Sets the Link Aggregation load balance algorithm. Enumeration: 'sourceMAC': 1, 'destMAC': 2, 'sourceAndDestMAC': 3, 'destIP': 5, 'sourceIP': 4, 'sourceAndDestIP': 6.

A table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table for each physical port.

A list of Link Aggregation Control configuration parameters for each Aggregation Port on this device.

The index of the port.

The priority value assigned to this Aggregation Port. This 16-bit value is read-write.

This object indicates LACP-Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and partner are both in passive mode, they do not exchange LACP packets. Enumeration: 'active': 1, 'passive': 2.

This object indicates LACP-Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds. Enumeration: 'short': 1, 'long': 2.

Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning. Enumeration: 'on': 1, 'off': 2.

The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet value set up as '# 0x0F 0xFF 0xFF 0xFF' means from port 1 to port 4 are not in auto learning state, the other ports are in auto learning state. It can be set up when Disable Auto Learning is enable.

A list of the Static MACs

A Static MAC entry containing the mac and forwarding port.

The VLAN ID of the static MAC entry.

The MAC address associated of the static MAC entry.

The forwarding port of the static MAC entry.

The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC.

Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops performing protocol operations. Enumeration: 'disabled': 2, 'enabled': 1.

This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.

This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.

When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'igsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.

The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'igsRobustnessValue' queries before removing the port from the group membership information in the forwarding database.

This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs.

The maximum query response time advertised in IGMPv2 general queries on this interface.

This table contains the list of ports through which a router, in a particular VLAN is reachable.

Contains the VLAN ID and list of ports on which routers are present in the VLAN.

VLAN ID of the ports through which router is reachable.

List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.

This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system.

Contains snooping status , version and fast leave configuration for a specific VLAN.

Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done.

This object allows you to enable/disable IGS function on a specific VLAN. Enumeration: 'disabled': 2, 'enabled': 1.

Indicates whether the switch is configured as a querier in the VLAN Enumeration: 'disabled': 2, 'enabled': 1.

The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries. Enumeration: 'disabled': 2, 'enabled': 1.

This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network.

List of ports which are configured statically as router ports

List of ports which can be configured statically as forbidden router ports.

Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table. Enumeration: 'disabled': 2, 'enabled': 1.

This table contains MAC based multicast forwarding information.

This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded.

VLAN ID pertaining to the Multicast forwarding entry

Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.

Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.

List of ports onto which the multicast data packets destined for this group will be forwarded.

This table is used to manage the IGMP Authentication function of the switch.

Contains management entities for IGMP Authentication function.

The port index of igsAccessAuthTable which indicates the port to be configured.

This object can be configured to set IGMP Authentication state to enabled/disabled on each port. Enumeration: 'disabled': 2, 'enabled': 1.

Enable/Disable GVRP mechanism. Enumeration: 'disabled': 2, 'enabled': 1.

The Join Time value assigned to this Join Time field. This 16-bit value is read-write.

The Leave Time value assigned to this Leave Time field. This 16-bit value is read-write.

The Leave-All Time value assigned to this Leave-All Time field. This 16-bit value is read-write.

A table containing static configuration information for each GVRP configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.

Information for a GVRP configured into the device by (local or network) management.

The index of the port.

The PVID value assigned to this Aggregation Port. This 16-bit value is read-write.

Enable/Disable GVRP State to this Aggregation Port. Enumeration: 'disabled': 2, 'enabled': 1.

Enable/Disable Ingress Checking mechanism of GVRP to this Aggregation Port. Enumeration: 'disabled': 2, 'enabled': 1.

Chose types All Frames/Tagged to this Aggregation Port. Enumeration: 'taggedOnly': 2, 'allFrames': 1.

Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues. Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8 for WS3 spec. Queues with higher weights get bandwidth before than other queues with less weights. Enumeration: 'wrr': 2, 'strictPriority': 1.

A list of cosOutputSchedule.

A list of cosOutputClass Weight.

A index of class 0 ~ 3.

cos weight

A list of port mapping priority Entries.

A list of 802.1p port mapping priority priorities.

A port identifier that is in the range of 1 to ifNumber.

For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For ingress tagged packets, if 802.1p not enabled D-Link Smart Switches will refer to these 4 different priority queues. Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

A list of 802.1p port default priority Entries.

A list of 802.1p port default priority priorities.

A port identifier that is in the range of 1 to ifNumber.

For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled. Enumeration: 'priority1': 1, 'priority0': 0, 'priority3': 3, 'priority2': 2, 'priority5': 5, 'priority4': 4, 'priority7': 7, 'priority6': 6.

For ingress untagged packets, the per port 'Effective Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled. Enumeration: 'priority1': 1, 'priority0': 0, 'priority3': 3, 'priority2': 2, 'priority5': 5, 'priority4': 4, 'priority7': 7, 'priority6': 6.

A table mapping evaluated User Priority to Traffic Class, for forwarding by the bridge. Traffic class is a number in the range (0..3).

User Priority to Traffic Class mapping.

For ingress tagged packets, D-Link Smart Switches will refer to these information and prioritize them with 4 different priority queues. If 802.1p is enabled.

The User Class the received frame is mapped to. Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 0 : IP ToS value = 0 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 01 : IP ToS value = 4 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 02 : IP ToS value = 8 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 03 : IP ToS value = 12 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 04 : IP ToS value = 16 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 05 : IP ToS value = 20 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 06 : IP ToS value = 24 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 07 : IP ToS value = 28 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 08 : IP ToS value = 32 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 09 : IP ToS value = 36 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 10 : IP ToS value = 40 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 11 : IP ToS value = 44 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 12 : IP ToS value = 48 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 13 : IP ToS value = 52 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 14 : IP ToS value = 56 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 15 : IP ToS value = 60 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 16 : IP ToS value = 64 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 17 : IP ToS value = 68 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 18 : IP ToS value = 72 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 19 : IP ToS value = 76 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 20 : IP ToS value = 80 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 21 : IP ToS value = 84 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 22 : IP ToS value = 88 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 23 : IP ToS value = 92 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 24 : IP ToS value = 96 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 25 : IP ToS value = 100 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 26 : IP ToS value = 104 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 27 : IP ToS value = 108 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 28 : IP ToS value = 112 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 29 : IP ToS value = 116 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 30 : IP ToS value = 120 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 31 : IP ToS value = 124 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 32 : IP ToS value = 128 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 33 : IP ToS value = 132 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 34 : IP ToS value = 136 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 35 : IP ToS value = 140 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 36 : IP ToS value = 144 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 37 : IP ToS value = 148 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 38 : IP ToS value = 152 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 39 : IP ToS value = 156 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 40 : IP ToS value = 160 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 41 : IP ToS value = 164 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 42 : IP ToS value = 168 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 43 : IP ToS value = 172 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 44 : IP ToS value = 176 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 45 : IP ToS value = 180 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 46 : IP ToS value = 184 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 47 : IP ToS value = 188 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 48 : IP ToS value = 192 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 49 : IP ToS value = 196 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 50 : IP ToS value = 200 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 51 : IP ToS value = 204 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 52 : IP ToS value = 208 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 53 : IP ToS value = 212 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 54 : IP ToS value = 216 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 55 : IP ToS value = 220 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 56 : IP ToS value = 224 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 57 : IP ToS value = 228 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 58 : IP ToS value = 232 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 59 : IP ToS value = 236 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 60 : IP ToS value = 240 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 61 : IP ToS value = 244 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 62 : IP ToS value = 248 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

DiffServ Type 63 : IP ToS value = 252 Enumeration: 'high': 2, 'highest': 3, 'medium': 1, 'low': 0.

A list of port priority settings.

A list of port priority settings Entries.

A port identifier that is in the range of 1 to ifNumber.

The port priority setting type. (ex. none = 0, port mapping = 1, 802.1p = 2, DSCP = 4. If you want enable 802.1p & DSCP, the value is 2 + 4 = 6.

A list of priority by acl setting.

A list of priority by acl setting entry.

Index of priority by acl setting.

Type of priority by acl setting. Enumeration: 'udp': 3, 'protocol': 5, 'ip': 1, 'tcp': 2, 'mac': 0, 'vlanid': 4.

Dst MAC of priority by acl setting.

Dst IP of priority by acl setting

Dst TCP/UDP port of priority by acl setting

VLAN ID of priority by acl setting

Ip protocol number of priority by acl setting

Be mapped class of priority by acl setting. Enumeration: 'class2': 2, 'class3': 3, 'class0': 0, 'class1': 1.

Status of priority by acl setting.

A table to control the rate limiting parameters either for the entire switch or for each interface in the switch.

An entry appears in this table for each physical interface in the switch.

The interface index for which the configuration in this entry applies.

Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000 (Kbits per second) in GE port. (Note: The multiple of 1850 Kbits/sec will be set automatically because the resolution of Giga-port Tx bandwidth control is 1850 Kbits/sec.)

Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port.

This object indicates storm control function is enabled or disabled for device. When you enable broadcast storm control function, D-Link Smart Switches will allowed you to limit the number of broadcast packets per second going through device. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates storm control function is control broadcast packet or multicast packet or dlf packet. Enumeration: 'broadcastonly': 1, 'dlfMulticastAndbroadcast': 3, 'multicastAndbroadcast': 2.

Allows to configure the limiting value for the maximum number of Kbits/sec that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting on this interface. The value that can be set for this object is limited by the underlying hardware. The limit value must be between 64~1024000 and limit value is multiple of 64. (Notice : if the limit value is 0, it means unlimited.)

The trap setting of traffic control. Enumeration: 'stormCleared': 2, 'none': 0, 'both': 3, 'stormOccurred': 1.

The traffic control table.

The traffic control entry.

The traffic control index.

The action mode of traffic control. Enumeration: 'drop': 0, 'shutdown': 1.

The control type of traffic control. (b: Broadcast, m: Multicast, u: Unknown Unicast) Enumeration: 'none': 0, 'b': 1, 'mb': 3, 'm': 2, 'um': 6, '': 4, 'umb': 7, 'ub': 5.

The threshold of traffic control.

The count down value of traffic control.

The time interval of traffic control.

This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection. Enumeration: 'disabled': 2, 'enabled': 1.

A table to configure trusted host in the system.

Each entry in this table represents rules for particular trusted host.

The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.

Used to mask with IP address, it allow you set a subnet as a trusted host entry.

The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.

A table to control port security features of the device.

An entry appears in port security table for each interface in the system.

The interface index for which the configuration in this entry applies.

Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled. Enumeration: 'disabled': 2, 'enabled': 1.

Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 64. Note: Set value 0 means cannot learn MAC address.

Configures port security lock address mode for the interface. deleteOnReset : The locked addresses will not age out until the Switch has been reset. deleteOnTimeout : The locked addresses will age out after the aging timer expires. Permanent : The locked addresses will not age out after the aging timer expires. Enumeration: 'permanent': 3, 'deleteOnTimeout': 2, 'deleteOnReset': 1.

A table to control port security FDB Permanent of the device.

An entry appears in port security table for each interface in the system.

The index of the port security MAC entry.

The VLAN ID of the port security MAC entry.

The MAC address associated of the port security MAC entry.

The forwarding port of the port security MAC entry.

A table to control ARP Spoofing prevention for the entire switch or for each interface in the switch.

An entry appears in this table for each interface in the system.

Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.

Ethernet Mac Address.

Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.

This object indicates the status of this entry.

The system wide ACL mode in IPMB. Enumeration: 'disable': 0, 'modeARP': 1.

The trap event option in IPMB. Enumeration: 'enable': 1, 'disable': 2.

Specifies the port numbers which check incoming IP address and MAC address if issIpMacPortBindingStatus is enable.

Specifies the port numbers which don't check incoming IP address and MAC address if issIpMacPortBindingStatus is enable.

A table to control IP-MAC-Port Binding features either for the entire switch or for each interface in the switch. Parameters in this table are valid only when the 'issIpMacPortStatus' for the switch is not 'disabled'.

An entry appears in this table for each interface in the system.

Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.

Ethernet Mac Address.

Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.

This object indicates the status of this entry.

An entry appears in this table for each interface in the system.

An entry appears in this table for each interface in the system.

Blocked Mac Address.

Blocked IP.

Blocked port.

This object indicates the status of this entry.

This object is for enabling or disabling secure HTTP in the system. Enumeration: 'enable': 1, 'disable': 2.

This object is to configure the cipher-suites list. Bits: 'rsa-null-md5': 0, 'dh-rsa-3des-sha': 5, 'rsa-3des-sha': 3, 'dh-rsa-des-sha': 4, 'rsa-des-sha': 2, 'rsa-exp1024-des-sha': 6, 'rsa-null-sha': 1.

To enable or disable DHCP Server Screening port list.

A table to control filter DHCP Server for the entire switch or for each interface in the switch.

An entry appears in this table for each interface in the system.

Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.

Ethernet Mac Address.

Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.

This object indicates the status of this entry.

This object is for enabling or disabling ssh in the system. Enumeration: 'enable': 1, 'disable': 2.

This object indicates the max auth fail retry attempt times.

This object indicates one SSH session rekey time interval. Enumeration: 'ten-min': 10, 'never': 0, 'sixty-min': 60, 'thirty-min': 30.

This object indicates max SSH session number supported in system.

This object indicates SSH connection timeout value.

The object indicates authen method password is enabled or disabled. Enumeration: 'enable': 1, 'disable': 2.

The object indicates authen method public-key is enabled or disabled. Enumeration: 'enable': 1, 'disable': 2.

The object indicates authen method host-key is enabled or disabled. Enumeration: 'enable': 1, 'disable': 2.

This object is to configure the cipher-suites list. Bits: 'dESCBC': 1, 'tripleDESCBC': 0.

This object is to configure the MAC-list. Bits: 'hMAC-SHA1': 0, 'hMAC-MD5': 1.

The object indicates Public key generating algorithm RSA is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

A table to configure SSH user auth in the system.

An entry to configure user auth in the system.

The Schedule identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 8.

The ssh user name associated with the SSH suer Info. entry (e.g., `admin, user').

The object indicates which auth used by the user. Enumeration: 'publickey': 4, 'hostbased': 1, 'password': 2.

The ssh host name associated with the SSH suer Info. entry (e.g., `DUT1, DUT2').

SSH HostBased IP Address of the system.

A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel

There is one entry in this table for each created port-channel port

The ifIndex of the port-channel(Aggregator's interface index).

Port list of port channel.

This object indicates the Access Authentication is enable or disable. Enumeration: 'disabled': 2, 'enabled': 1.

Timeout in second for login authentication response.

The amount for login authentication, if login failure exceed, connection or access would be locked.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH.

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP.

A table that contains informations about server group.

A list of the group including servers.

A value that uniquely identifies this SwAACServerGroupEntry .

A human-readable text string of the method group. The name is writable only if Group is new created, which the value of aacServerGroupRowStatus is 'notReady'.

The list of servers in the group, each bit indicates a specified server ID. The server must be created before including it. Bits: 'id-4': 3, 'id-5': 4, 'id-6': 5, 'id-7': 6, 'id-1': 0, 'id-2': 1, 'id-3': 2, 'id-8': 7, 'id-9': 8, 'id-16': 15, 'id-14': 13, 'id-15': 14, 'id-12': 11, 'id-13': 12, 'id-10': 9, 'id-11': 10.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table that contains information about severs.

A list of the information of server .

A value that uniquely identifies this SwAACServerGroupEntry.

The IP address of Server

The authentication protocol provided by the Server. Enumeration: 'tacacs-plus': 1, 'radius': 2.

The TCP/IP port .

The key used while authentication process.

Server response timeout .

The client retry count .

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table that contains information about Login authentication method lists.

A list of the Authentication methods.

A value that identifies this method list.

A human-readable text string of the method list.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'tacacs-plus': 1, 'local': 0.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'tacacs-plus': 1, 'local': 0.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'tacacs-plus': 1, 'local': 0.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'tacacs-plus': 1, 'local': 0.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table that contains information about Enable authentication method lists.

A list of the Authentication methods.

A value that identifies this method list.

A human-readable text string of the method list.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'tacacs-plus': 1, 'local': 0.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'tacacs-plus': 1, 'local': 0.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'tacacs-plus': 1, 'local': 0.

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex. Enumeration: 'radius': 2, 'none': -1, 'tacacs-plus': 1, 'local': 0.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

This object is used to set Local Enable Password.

A table to ACL profile .

Each entry in this table is a ACL profile. Index to the table is ACL profile ID.

The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.

The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, arpSP-permit(4) - for ARP Spoofing prevention entry, arpSP-deny(5) - for ARP Spoofing prevention entry, voiceVlan(6) - for Voice VLAN OUI entry. Note that only l2 and l3 could be set by user, other is reserved for system to show information. Enumeration: 'voiceVlan': 6, 'l2': 1, 'l3': 2, 'arpSP-permit': 4, 'arpSP-deny': 5.

The number of rules in this profile.

Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST-MAC 0 (LSB) L2 SRC-MAC 1 L2 VID 2 L2 8021P-PRIORITY 3 L2 ETHER-TYPE 4 L3 DSCP 5 L3 ICMP-TYPE 6 L3 ICMP-CODE 7 L3 IGMP-TYPE 8 L3 DST-IP 9 L3 SRC-IP 10 L3 DST-PORT 11 L3 SRC-PORT 12 L3 TCPFLAG 13 ARP-SP ARP-SENDER-MAC 14 ARP-SP ARP-SENDER-IP 15 (MSB) ------------------------------------------- The value is in Hex format.

The ACL Profile destination MAC address mask. If DST-MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care.

The ACL Profile source MAC address mask. If SRC-MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.

Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none. Enumeration: 'none': 0, 'udp': 17, 'tcp': 6, 'ipMask': 255, 'icmp': 1, 'igmp': 2.

The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.

The ACL Profile destination IP address mask. If DST-IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'

The ACL Profile source IP address mask. If SRC-IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'

The ACL Profile UDP/TCP destination port mask. If DST-PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.

The ACL Profile UDP/TCP source port mask. If SRC-PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.

The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.

The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.

This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted.

A table to configure L2 filter rules in the system.

Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID.

L2 Filter rule ID.

ACL Profile ID which this rule join.

The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition.

Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition.

Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address

Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.

802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition.

The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting.

The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting.

Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.

Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded. Enumeration: 'replaceDSCP': 5, 'rateLimit': 4, 'drop': 2, 'allow': 1, 'mirror': 3.

Rate limit for matched packet.

Replace DSCP for matched packet.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

A table to configure L3 filter rules in the system.

Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID.

L3 Filter rule ID.

The Profile ID which this rule join.

The type of protocol to be checked against the packet. Enumeration: 'udp': 17, 'icmp': 1, 'tcp': 6, 'igmp': 2.

The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.

The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),

The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),

Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.

Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.

The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.

The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.

The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.

The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.

The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.

The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.

The TCP ACK bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition. Enumeration: 'dont-care': -1, 'notEstablish': 2, 'establish': 1.

The TCP RST bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition. Enumeration: 'dont-care': -1, 'notEstablish': 2, 'establish': 1.

The TCP Urg bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition. Enumeration: 'dont-care': -1, 'notEstablish': 2, 'establish': 1.

The TCP Psh bit to be checked against the packet. The default value is 'dont-care'(-1). which means the rule don't care this condition. Enumeration: 'dont-care': -1, 'notEstablish': 2, 'establish': 1.

The TCP Syn bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition. Enumeration: 'dont-care': -1, 'notEstablish': 2, 'establish': 1.

The TCP Fin bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition. Enumeration: 'dont-care': -1, 'notEstablish': 2, 'establish': 1.

The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.

The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition.

Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.

Specifies the action to be taken on the packet if the filter rule matches. Enumeration: 'replaceDSCP': 5, 'rateLimit': 4, 'drop': 2, 'allow': 1, 'mirror': 3.

Rate limit for matched packet.

ReplaceDSCP for matched packet.

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

This object is for enabling or disabling syslog alert features in the system and the syslog will save to flash or send to remote syslog server. System Logs record and manage events, as well as report errors and informational messages. Enumeration: 'enable': 1, 'disable': 0.

This object is for choosing the method to save syslog into flash. Enumeration: 'timeInterval': 1, 'logTrigger': 2, 'onDemand': 0.

When savemode is time interval, it's used to set the interval minutes of system save syslog to flash.

The table of syslog remote server.

The list of syslog remote server entry.

The index of syslog remote server.

The IP Address of syslog remote server.

Specifies the log level option to be set for a specific server. Enumeration: 'information': 6, 'all': 7, 'warning': 4.

The Syslog standard facilities. The facility to be used when sending Syslog messages to this server. Enumeration: 'local5': 168, 'local4': 160, 'local7': 184, 'local6': 176, 'local1': 136, 'local0': 128, 'local3': 152, 'local2': 144.

The value is for setting UDP Port.

The status for this server. If enable, system will send message to this server. Enumeration: 'disabled': 0, 'enabled': 1.

Row status of this server entry.

Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged switchs.The Switch will automatically shutdown the port and sends a log to the administrator. Enumeration: 'disabled': 2, 'enabled': 1.

Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP packet automatically.

This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop Detection Recover Time. The default is 60 seconds.

A table to control Loopback detection features either for the entire switch or for each interface in the switch.

An entry appears in this table for each interface in the system.

The interface index of the port for which the configuration in this entry applies.

Provides control to per port enable or disable the loopback detection function. Default is disabled. Enumeration: 'disabled': 2, 'enabled': 1.

The loop status for this port. Enumeration: 'disabled': 2, 'normal': 1.

Enable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the packet can be studied. Enumeration: 'disabled': 2, 'enabled': 1.

Specifies the port to which the mirrored traffic in the system is to be copied.

Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.

Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.

A list of the Static MACs

A Static MAC entry containing the mac and forwarding port.

The VLAN ID of the static MAC entry.

The MAC address associated of the static MAC entry.

The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length.

The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.

This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UTC, January 1, 2009) and smaller than 2145916799 (23:59:59 UTC, December 31, 2037).

SNTP First Server's IP Address

SNTP Second Server's IP Address

SNTP Poll Interval In Seconds (30-99999)

Enable/Disable SNTP function in the system. Enumeration: 'local': 2, 'sntp': 1.

This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes. Enumeration: 'offset90min': 90, 'offset120min': 120, 'offset60min': 60, 'offset30min': 30.

Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)

The start month of Daylight Saving Time.

The start day of Daylight Saving Time.

The start hour of Daylight Saving Time.

The start minute of Daylight Saving Time.

The end month of Daylight Saving Time.

The end day of Daylight Saving Time.

The end hour of Daylight Saving Time.

The end minute of Daylight Saving Time.

This object is for Annual(1) or Disabled(2) DST state in the system. Enumeration: 'disabled': 2, 'annual': 1.

Voice VLAN is a feature that allows you to automatically place the voice traffic from IP phone to an assigned VLAN to enhance the VoIP service. This object is for enabling or disabling Voice Vlan function in the system. If the Vlan mode is in Asymmetric VLAN mode, Voice VLAN can not be enabled. Enumeration: 'disabled': 2, 'enabled': 1.

The ID of VLAN that you want the voice traffic to be in. It must be a exist vlan id.

A period of time in hour to remove a port from voice VLAN if the port is an automatic VLAN member. The Timeout range is 1~120 hours. Default aging time is 1 hour.

The 802.1p priority levels of the traffic in the Voice VLAN. Enumeration: 'high': 1, 'medium': 2, 'highest': 0, 'low': 3.

A table that contains Voice Vlan Port Control configuration information.

A list of Voice Vlan Control configuration parameters for each Port on this device.

The voice vlan port index.

This object is for enabling or disabling Voice Vlan Auto Detection in the port. If the auto detection is enable, switch will add this port to the voice VLAN automatically if it detects the device OUI matches the Telephony OUI. If the port is a static member of voice vlan or a LA member, it can not enable voice vlan auto detection. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates Voice vlan state to this Port. manual - this port is a static member of voice vlan. dynamic - this port is a dynamic member of voice vlan. none - this port is not a member of voice vlan. Enumeration: 'dynamic': 2, 'none': 3, 'manual': 1.

A voice vlan OUI entry containing the description and mac.

A voice vlan OUI entry containing the description and mac.

An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the voice traffic's OUI that user created.

The Description for the OUI.

Voice vlan OUI Mask. Always be FF:FF:FF:00:00:00.

This object indicates the status of this entry. To create a new entry, you must set the voicevlanOUIStatus to be CreateAndGo, then this entry will turn to be Active.

This object is for enabling or disabling RMON function. Enumeration: 'disabled': 2, 'enabled': 1.

A list of Ethernet statistics entries.

A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1

The value of this object uniquely identifies this etherStats entry.

This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated etherStatsStatus object is equal to valid(1).

The entity that configured this entry and is therefore using the resources assigned to it.

The status of this etherStats entry.

A list of history control entries.

A list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyControlInterval.2

An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.

This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated historyControlStatus object is equal to valid(1).

The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry. When this object is created or modified, the probe should set historyControlBucketsGranted as closely to this object as is possible for the particular probe implementation and available resources.

The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This interval can be set to any number of seconds between 1 and 3600 (1 hour). Because the counters in a bucket may overflow at their maximum value with no indication, a prudent manager will take into account the possibility of overflow in any of the associated counters. It is important to consider the minimum time in which any counter could overflow on a particular media type and set the historyControlInterval object to a value less than this interval. This is typically most important for the 'octets' counter in any media-specific table. For example, on an Ethernet network, the etherHistoryOctets counter could overflow in about one hour at the Ethernet's maximum utilization. This object may not be modified if the associated historyControlStatus object is equal to valid(1).

The entity that configured this entry and is therefore using the resources assigned to it.

The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1).

A list of alarm entries.

A list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8

An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device.

The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in the case of deltaValue sampling - the interval should be set short enough that the sampled variable is very unlikely to increase or decrease by more than 2^31 - 1 during a single sampling interval. This object may not be modified if the associated alarmStatus object is equal to valid(1).

The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, Counter64, Gauge, or TimeTicks) may be sampled. Because SNMP access control is articulated entirely in terms of the contents of MIB views, no access control mechanism exists that can restrict the value of this object to identify only those objects that exist in a particular MIB view. Because there is thus no acceptable means of restricting the read access that could be obtained through the alarm mechanism, the probe must only grant write access to this object in those views that have read access to all objects on the probe. During a set operation, if the supplied variable name is not available in the selected MIB view, a badValue error must be returned. If at any time the variable name of an established alarmEntry is no longer available in the selected MIB view, the probe must change the status of this alarmEntry to invalid(4). This object may not be modified if the associated alarmStatus object is equal to valid(1).

The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), the value of the selected variable will be compared directly with the thresholds at the end of the sampling interval. If the value of this object is deltaValue(2), the value of the selected variable at the last sample will be subtracted from the current value, and the difference compared with the thresholds. This object may not be modified if the associated alarmStatus object is equal to valid(1). Enumeration: 'absoluteValue': 1, 'deltaValue': 2.

A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval was less than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is greater than or equal to this threshold and the associated alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3). After a rising event is generated, another such event will not be generated until the sampled value falls below this threshold and reaches the alarmFallingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).

A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was greater than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is less than or equal to this threshold and the associated alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3). After a falling event is generated, another such event will not be generated until the sampled value rises above this threshold and reaches the alarmRisingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).

The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).

The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).

The entity that configured this entry and is therefore using the resources assigned to it.

The status of this alarm entry.

A list of events to be generated.

A set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be named eventLastTimeSent.6

An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur.

A comment describing this event entry.

The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-trap, an SNMP trap is sent to one or more management stations. Enumeration: 'snmptrap': 3, 'none': 1, 'log': 2, 'logandtrap': 4.

If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string.

The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has associated entries in the log table, all connected management stations should retrieve those log entries, as they may have significance to all management stations connected to this device

The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent.

Enable/Disable Static 802.1x. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates the authentication mode of the device. Enumeration: 'portBase': 1, 'macBase': 2.

The authentication method used to authenticate users. Enumeration: 'authProtocolRadiusEap': 1, 'authProtocolLocal': 2.

A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.

The configuration information for an Authenticator Port.

A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number.

The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine.

The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine.

The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine.

The value of the maxReq constant currently in use by the Backend Authentication state machine.

The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine.

The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine.

The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1). Enumeration: 'disabled': 2, 'enabled': 1.

The current value of the controlled Port control parameter for the Port. Enumeration: 'auto': 2, 'forceUnauthorized': 1, 'forceAuthorized': 3.

The current value of the controlled Port control parameter for the Port. Enumeration: 'authenticator': 1, 'none': 2.

The current value of the controlled Port control parameter for the Port. Enumeration: 'both': 0, 'in': 1.

A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.

The configuration information for an Authenticator Port.

The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.

This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.

The status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthUserName objects must be explicitly set.

A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.

The configuration information for an Authenticator Port.

A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3.

The IP address of the RADIUS server referred to in this table entry.

The value is for setting UDP Port.

The value is for setting UDP Port.

The value is for setting UDP Port.

The value is for setting UDP Port.

This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.

The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthRadiusServerIndex objects must be explicitly set.

The VLAN name of guest VLAN.

This object indicates the guest VLAN port members of this device.

Used to delete the guest VLAN. Enumeration: 'start': 2, 'none': 1.

This object can enabled or disabled MAC Notification. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates the time interval in second for trigger the MAC notify message.

This object indicates the history size of variation MAC in address table. The default value is 1 .

A table to control Loopback detection features either for the entire switch or for each interface in the switch.

An entry appears in this table for each interface in the system.

The interface index of the port for which the configuration in this entry applies.

Provides control to per port enable or disable the loopback detection function. Default is disabled. Enumeration: 'disabled': 2, 'enabled': 1.

Enable or Disable SMTP function. Enumeration: 'disabled': 0, 'enabled': 1.

SMTP Server's IP Address

SMTP Server's port

The sender's (DUT) mail address .

Receivers' mail address table.

Receivers' mail address entry.

Receivers' mail address index (1~8).

Receivers' mail address.

Rowstatus of the receiver's mail address.

Enable/Disable IGMP Multicast Vlan function. Enumeration: 'disabled': 2, 'enabled': 1.

Information about the IGMP snooping multicast VLAN table.

The entry of igmpMulticastVlanTable.

This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.

This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.

This object indicates the port list of the source ports of the IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.

This object indicates the port list of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.

This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN.

This object can be used to enable or disable the IGMP snooping multicast VLAN. Enumeration: 'disabled': 2, 'enabled': 1.

The replacement source IP of this multicast VLAN.

This object indicates the status of this entry.

The table containing the IGMP snooping multicast VLAN group information

Information about the current IGMP snooping multicast VLAN group.

This object indicates the VID of the IGMP snooping multicast VLAN group.

Specifies the multicast address list for this VLAN.

Specifies the multicast address list for this VLAN.

This object indicates the status of this entry.

This object indicates DHCP relay function is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates the maximum number of router hops that the BOOTP packets can cross.

This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.

This table indicates the IP address as a destination to forward (relay) DHCP packets to.

A list of information indicates the IP address as a destination to forward (relay) DHCP packets to.

This object indicates the name of the IP interface.

This object indicates the DHCP server IP address.

This object indicates the status of this entry.

This object indicates DHCP relay option 82 function is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates DHCP relay option 82 Check function is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

This object indicates DHCP relay option 82 policy. Enumeration: 'keep': 3, 'drop': 2, 'replace': 1.

This object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defined by writing to the swDHCPRelayOption82RemoteID object. Enumeration: 'default': 1, 'userdefined': 2.

This object displays the current remote ID of the device. If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If swDHCPRelayOption82RemoteIDType is set to user-defined, a new value can be written to this object.

This object indicates DHCP local relay function of VLAN is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 1.

This table indicates the IP address as a destination to forward (local relay) DHCP packets to.

A list of information indicates the IP address as a destination to forward (local relay) DHCP packets to.

This object displays the current VLAN ID of the device.

This object indicates DHCP local relay function of VLAN is enabled or disabled. Enumeration: 'disabled': 2, 'enabled': 3.

The smart console utility's IP address is used to recive trap events.

Enable/Disable system trap events in the switch system. Enumeration: 'illegalLogin': 2, 'none': 0, 'deviceBootUp': 1, 'both': 3.

Enable/Disable fiber port trap event in the system. Enumeration: 'enable': 1, 'disable': 2.

Enable/Disable twisted port trap event in the system. Enumeration: 'enable': 1, 'disable': 2.

Enable/Disable RSTP state change trap event in the system. Enumeration: 'enable': 1, 'disable': 2.

Enable/Disable firmware upgrading trap event in the system. Enumeration: 'enable': 1, 'disable': 2.

Enable/Disable trap event in the system. Enumeration: 'enable': 1, 'disable': 2.

This object is used for enabling or disabling LLDP in the system. Enumeration: 'enable': 1, 'disable': 2.

The time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpMessageTxInterval * lldpMessageTxHoldMultiplier))

This object is used for LLDP packet update frequency. The timer in units of seconds.

This object is used for LLDP Reinitialization Delay. The timer in units of seconds.

The lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local systems MIB. The recommended value for the lldpTxDelay is set by the following formula: 1 <= lldpTxDelay <= (0.25 * lldpMessageTxInterval).