CHIPCOMMIB: View SNMP OID List / Download MIB

The product type represented by this agent. Enumeration: 'product-8383B': 3, 'product-5200M-MGT': 7, 'product-5100M-MGT': 1, 'product-5300M-MGT': 5, 'product-5112H-UTP': 4, 'product-6100M-MGT': 12, 'product-4112H-MTP': 8, 'product-5102B-EE': 2.

The date that the product was last serviced in the format yymmdd. If this date is unknown, the value of this object is '000000'.

The IP (source) Address of the last authenticated SNMP PDU received by this entity before this request. An IP Address of 00.00.00.00 represents the default value.

The result of this product's diagnostic test(s). If any test fails, this will have the failed(2) value. Note, many products do not operate after a diagnostic failure. In this case, no SNMP communication would be available. Enumeration: 'failed': 2, 'passed': 1.

The serial number of this product.

A unique ID used for grouping disparate agents together. For example, a concentrator may contain multiple agents. This ID is could be assigned by the management station to identify all of these agents as being contained in the same concentrator.

The version identifier(s) for this agent.

The source IP Address of the last SNMP request that caused an authentication failure trap to be generated. This object is also included in the SNMP authenticationFailure trap.

A snapshot of sysUpTime when the last trap was generated. This attribute can be used to save polling by a management station. If there have been no traps generated since the last poll, there is no need for the station to poll again.

Setting chipEchoStart to startEcho(2) causes the device to begin an ICMP echo sequence using the parameters indicated by the rest of the chipEcho group. Enumeration: 'noEcho': 1, 'startEcho': 2.

The IP Address to which the device will ping. This object can only be set to valid unicast class A, class B, or class C addresses. The default IP Address is loopback (127.0.0.1).

The actual pattern to be contained in the ICMP echo packet. Enumeration: 'zeroes': 1, 'mixed': 3, 'ones': 2.

The number of ICMP echo packets (pings) to send.

The size of the ICMP echo packet (ping) to send when chipEchoStart is set. The valid range is between 64 and 1500 octets.

The count of ICMP echo response packets received since the last PING was initiated.

The slot id of this agent.

Resetting mastership causes a new mastership election to occur. The agent with the highest mastership priority will become the new master. If there is more than one agent with the highest priority, the selection between those agents will be arbritrary. Enumeration: 'reset': 2, 'noReset': 1.

A table of agents in the concentrator as seen by this agent. A master will see all the agents; a slave will only see itself.

A profile of an agent within the concentrator.

The slot number that identifies the referenced agent.

The unique identifier for this agent. Often this is the value of ifPhysAddress for the first interface.

An IP Address that can be used to communicate to this agent. Note, this object's value may change as the agent switches to different sub-networks.

The mastership status of this agent. Enumeration: 'non-master': 2, 'master': 1, 'electing': 3.

The mastership priority of this agent. Ten is the highest and one is the lowest. Never means will not be able become master. Some agents do not have the capability to become master (the etherent to ethernet bridge, e.g.) and setting those agents to a value other than never(11) will generate an invalid value error. Priority is only used when an election occurs. Mastership is not pre-emptive; use the reset mastership command (olAgentsMasterReset). Enumeration: 'seven': 7, 'never': 11, 'ten': 10, 'nine': 9, 'six': 6, 'three': 3, 'two': 2, 'four': 4, 'five': 5, 'eight': 8, 'one': 1.

The subslot index for this agent. For agents not located in the ONcore system, this object will always return 1 for this object value.

This object identifies the type of concentrator represented by this agent. Enumeration: 'hub-4112-HMTP': 7, 'hub-5006C-FT': 3, 'hub-6017C-A': 6, 'hub-5006C': 2, 'hub-5006C-HC': 4, 'hub-5017C': 1, 'hub-5017C-LS': 9, 'hub-5006C-HC-FT': 5.

Setting this value to reset(2) causes this concentrator to reset. Enumeration: 'reset': 2, 'noReset': 1.

The number of slots in this concentrator. This value is the sum total of all payload slots plus any slots reserved for controller modules. For example, for an ONcore agent operating in a 17-slot ONcore hub, this object will have the value 19 (17 payload slots plus 2 controller slots). Similarly, if an ONline hub contains a hidden controller, then this object will have the value 7 (the hidden controller does not actually occupy a main slot in the 6-slot concentrator, but it will report itself as slot 7). Also, for an ONline agent operating in an ONcore hub, this object's value will not exceed 17.

A bit string where the least significant bit corresponds to slot 1. A '1' in the bit indicates that a module is present in that slot. The number of octets provided is based on the olConcNumSlots value divided by 8. Any extra bits (for example, bits 18-24 for 17 slots) are meaningless. For example, the string 0x01 0xFF 0xFF would represent a full 17 slot concentrator.

The overall temperature status for this concentrator. This object's value is an aggregate of all the temperature probes in the concentrator, such that, when at least one probe reports extreme temperature, this object will have the value extremeTemp(2). This object will have the value warning(3) prior to reporting the value extremeTemp(2) as a means of warning of a possible hub overheat condition. Enumeration: 'extremeTemp': 2, 'warning': 3, 'okay': 1.

The total capacity of power supplies for this concentrator.

A table that contains information about each potential power supply in the concentrator.

A list of information for each power supply in the concentrator.

Identifies the power supply for which this entry contains power supply information. For systems with the primary and backup power supply (as opposed to the N+1 design), index 1 refers to the primary, and index 2 refers to the backup.

The current desired state of the power supply. A power supply in standby does not provide power to the concentrator. Note, in a Load Sharing Hub, this object is read only. Enumeration: 'standby': 2, 'activate': 1.

The current operational state of the power supply. A power supply in standby does not provide power to the concentrator. Enumeration: 'active': 1, 'standby': 2, 'faulty': 3, 'not-installed': 4.

The overall status of the fan(s). When fan operational status is known, this object's value is an aggregate of all fan status in the concentrator such that, when at least one fan unit is faulty, this object will have the value faulty(2). Enumeration: 'unknown': 5, 'faulty': 2, 'okay': 1, 'not-installed': 4.

A table that contains information about the concentrator environment.

A list of information for each monitored component in this concentrator.

The type of hardware component monitored in this concentrator. Enumeration: 'ls-pdb': 1.

The status of the monitored hardware component. Enumeration: 'faulty': 2, 'okay': 1.

A table that contains generic information about every module that is present within the concentrator. If the concentrator is the ONcore Hub, then only the motherboard is present in this table.

A list of information for each module in the concentrator. If the concentrator is the ONcore Hub, then only the motherboard is present in this table.

The unique slot number of this module. Its value ranges between 1 and olConcNumSlots and remains constant at least from one re-initialization of the entity's network management system to the next re-initialization.

The unique type identifier for this module. This type is used to identify the branch in olSpecMods (see below). module-unmanageable(1) means that only the following objects are valid for this module: olModSlotIndex olModClass olModVersion olModVendor olModReset olModConfigToDips olModConfigured module-unknown(2) means that all the generic attributes are manageable, but there is no olSpecMods branch for this module as viewed by this agent. Enumeration: 'module-61nnM-TPL': 47, 'module-51nnM-MGT': 4, 'module-61nnM-FBP': 46, 'module-51nnM-FBP': 16, 'module-51nnM-TS': 21, 'module-51nnM-TP': 7, 'module-50nnM-RCTL': 23, 'module-53nnM-FBMIC': 26, 'module-52nnB-TT': 30, 'module-61nnD-MGT': 45, 'module-50nnM-RCLS': 51, 'module-51nnB-EE': 9, 'module-51nnM-TPL': 17, 'module-51nnM-FIB': 5, 'module-52nnM-FR': 20, 'module-60nnM-RCTL': 50, 'module-51nnM-BNC': 8, 'module-41nnH-MTP': 52, 'module-61nnM-CAR': 35, 'module-51nnM-TPLS': 48, 'module-unmanageable': 1, 'module-53nnM-TDDI': 65, 'module-50nnM-CTL': 3, 'module-51nnI-x': 31, 'module-51nnM-AUIM': 13, 'module-41nnH-ETP': 53, 'module-51nnM-FP': 15, 'module-5208M-TP': 14, 'module-51nnM-AUIF': 12, 'module-51nnM-UTP': 6, 'module-52nnM-EC': 62, 'module-60nnM-MGT': 43, 'module-52nnM-MGT': 32, 'module-51nnM-FB': 24, 'module-51nnM-FL': 22, 'module-51nnM-TPPL': 18, 'module-51nnM-TPCL': 29, 'module-53nnM-FIBST': 27, 'module-unknown': 2, 'module-51nnR-EE': 11, 'module-52nnM-TP': 19, 'module-53nnM-STP': 28, 'module-51nnR-ES': 10, 'module-53nnM-MGT': 25, 'module-50nnM-HCTL': 33.

The class of this module. Generally speaking, this object indicates the kind of module. Specifically, the class identifier specifies the internal representation of the module's managed information base. Enumeration: 'ethernet-media': 3, 'oncore-token-ring-media': 13, 'fddi-media': 8, 'token-ring-mgmt': 9, 'fddi-mgmt': 12, 'ethernet-connswitching-media': 10, 'oncore-oem-specials': 15, 'mgmt': 2, 'ethernet-portswitching-media': 5, 'token-ring-interconnect': 11, 'online-token-ring-mod-interconnect': 20, 'controller': 1, 'terminal-server': 7, 'oncore-download': 17, 'ethernet-carrier': 14, 'ethernet-interconnect': 4, 'token-ring-media': 6, 'ethernet-media-extended': 19.

A textual string containing information about the module.

The software version number of this module.

The actual manufacturer of this board. Enumeration: 'cisco': 2, 'ibm': 6, 'intellicom': 9, 'pilkington': 3, 'raycom': 7, 'chipcom': 1, 'retix': 8, 'datability': 5.

Setting this object to reset(2) causes this module to reset. Enumeration: 'reset': 2, 'noReset': 1.

Setting this object to configure(2) causes this module to configure based on the dip switch settings. Enumeration: 'noConfigure': 1, 'configure': 2.

This object indicates whether this module has already been configured. An unconfigured module is configured to a safe state where the network is isolated and the ports are disabled. Enumeration: 'configured': 2, 'notConfigured': 1.

The network that this module is attached to. If the value is other(1) or port-switching(3), setting this object to a different value will generate the invalidData error. If the value is port-switching(3), manage the networks via the olPortNetwork object. The value per-connector(20) is returned if the managed module is a per-connector switchable and the connectors are on different networks. The connector networks are managed by the objects defined in the olSpecMods branch specified for this module. Modules and ports on the same network intercommunicate. Setting the module to isolated(2) (or other isolated values), removes this module from the backplane. Setting this module to a value that is not the same protocol type will return an invalidData error. Setting this module to a value that it does not support will return an invalidData error. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'ethernet-4': 32, 'ethernet-5': 33, 'ethernet-6': 34, 'ethernet-7': 35, 'ethernet-8': 36, 'front-panel': 5, 'per-connector': 20, 'isolated': 2, 'other': 1, 'isolated-8': 28, 'isolated-9': 29, 'isolated-4': 24, 'isolated-5': 25, 'isolated-6': 26, 'isolated-7': 27, 'isolated-1': 21, 'isolated-2': 22, 'isolated-3': 23, 'fddi-2': 17, 'fddi-3': 18, 'fddi-1': 16, 'fddi-4': 19, 'port-switching': 3, 'isolated-10': 30, 'isolated-11': 31, 'token-ring-1': 9, 'token-ring-3': 11, 'token-ring-2': 10, 'token-ring-5': 13, 'token-ring-4': 12, 'token-ring-7': 15, 'token-ring-6': 14.

The network type of this module. port-switching(3) means that the network type differs depending on the port (like the router module). The network type reflects the valid values for olModNetwork. Enumeration: 'token-ring': 6, 'other': 1, 'ethernet': 5, 'serial': 8, 'port-switching': 3, 'fddi': 7.

The module's status. Enumeration: 'okay': 1, 'partial-failure': 21, 'fatalError': 10, 'booting': 20.

The number of ports on this module. Note, ports may be physical ports like 10BASE-T ports, or logical, like the bridge module ports.

The number of trunks on this module. Note, trunks are links that are, by definition, backbone connections. Examples of trunks are ring in and ring out ports for token ring, and the connections for rings to the backplane.

A table that contains generic information about each port on each module present within the concentrator.

A list of information about each port in the concentrator.

The slot number of this port's module.

The port number of this port within this module.

The type of port. logical(1) is used to manage port resources that may not map directly to physical connections. The OEBM, for example, has two logical ports, although those two ports can be assigned to different combinations of four physical connections. media(2) refers to ports such as those on the 10BASE-T module. Enumeration: 'media': 2, 'virtual': 5, 'logical': 1.

The connector type of this port. Enumeration: 'maui': 4, 'fiber': 5, 'ethernet-st': 24, 'db-25': 15, 'fddi-st': 13, 'rj45': 8, 'telco': 7, 'faui': 3, 'fddi-lc': 12, 'fddi-mic': 14, 'virtual': 11, 'ethernet-sma': 17, 'bnc': 2, 'db-50': 6, 'rj45S': 9, 'backPlane': 1, 'db-9': 10, 'ethernet-fc': 23.

The status of this port. Enumeration: 'fifoOverrun': 8, 'unknownStatus': 26, 'notInserted': 30, 'macRemoved': 29, 'security-breach': 25, 'noSquelch': 14, 'attach3174ToDirect': 35, 'noCable': 13, 'backup-link': 24, 'transientError': 37, 'attach3174To32-3299': 34, 'jabber': 3, 'attach3174Unknown': 32, 'attach3174To8-3299': 33, 'linkFailure': 2, 'connecting': 23, 'okay-standby': 19, 'remoteJabber': 5, 'fifoUnderrun': 9, 'okay': 1, 'invalidData': 6, 'wireFault': 28, 'beacon': 27, 'remoteLinkFailure': 4, 'noPhantom': 15, 'off': 22, 'attach3174Unavailable': 36, 'partition': 11, 'fatalError': 10, 'mjlp': 12, 'speedMismatch': 31, 'lowLight': 7.

The desired state of this port. Setting a port to be redundant-primary(3) or redundant-backup requires that the buddy slot and buddy port also be set to valid values (see appropriate olSpecMods objects). If the values associated with the redundant buddys are not valid, a genError will be returned. If the port is already redundant, an invalid set may result in both ports being disabled. Enumeration: 'remote': 7, 'redundant-rfs': 5, 'unknown': 9, 'enabled': 1, 'remote-diagnostics': 8, 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'local': 6.

The network that this port is attached to. If the value of olPortNetwork is per-module(4), then use the olModNetwork to manage this port. Setting olPortNetwork to a different value in this case will generate the invalidData error. Setting this port to a value that is not the same protocol type will return invalidData error. front-panel(5) is used for modules that have a logical port and a physical front connection. An example of this is the Eth2Eth Bridge module. Setting this port to a value that it does not support will generate an invalidData error. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'ethernet-4': 32, 'ethernet-5': 33, 'ethernet-6': 34, 'ethernet-7': 35, 'ethernet-8': 36, 'front-panel': 5, 'per-connector': 20, 'isolated': 2, 'other': 1, 'isolated-8': 28, 'isolated-9': 29, 'isolated-4': 24, 'isolated-5': 25, 'isolated-6': 26, 'isolated-7': 27, 'isolated-1': 21, 'isolated-2': 22, 'isolated-3': 23, 'fddi-2': 17, 'fddi-3': 18, 'fddi-1': 16, 'per-module': 4, 'fddi-4': 19, 'isolated-10': 30, 'isolated-11': 31, 'token-ring-1': 9, 'token-ring-3': 11, 'token-ring-2': 10, 'token-ring-5': 13, 'token-ring-4': 12, 'token-ring-7': 15, 'token-ring-6': 14.

The network type of this port. The type reflects the valid values for olPortNetwork. Enumeration: 'ethernet': 5, 'serial': 8, 'other': 1, 'fddi': 7.

Enabling this object for a port will allow the generation of port up (or port down) traps for port status transitions caused by end stations powering up (or down). Disabling this object will suppress the generation of port up (or port down) traps for a port. Note that this object is used in the trap generation decision only if chipAlertMode, an object in chipAlertTable, is set to filter(3). Some ports, such as integrated bridge or router ports do not support this feature. A getRequest on one of these types of ports will return a value of other(3), and a setRequest to enable(1) or disable(2) will return the invalidData object. Enumeration: 'enable': 1, 'other': 3, 'disable': 2.

A table that contains generic information about each trunk on each module present within the concentrator.

A list of information about each trunk in the concentrator.

The slot number of this trunk's module.

The trunk number of this trunk.

The type of trunk. ringIn(3) and ringOut(4) refer to special trunks on the token ring protocol type modules. Enumeration: 'ringIn': 3, 'other': 1, 'backplaneIn': 6, 'ringOut': 4, 'backplaneOut': 7.

The connector type of this trunk. Enumeration: 'backplane': 1, 'rj45S': 9, 'fiber': 5.

The status of this trunk. Enumeration: 'noCable': 13, 'okay': 1, 'wireFault': 28, 'linkFailure': 2, 'fatalError': 10, 'noSquelch': 14, 'beacon': 27, 'lostLock': 16, 'invalidConfig': 18, 'okay-standby': 19, 'upstreamNeighborLost': 17.

The desired state of this trunk. Enabling a trunk allows the trunk to pass network traffic. This object may be used to configure fiber trunk redundancy. Setting a trunk to be redundant-primary(3) or redundant-backup(4) requires that the buddy slot be previously set to a valid value (see appropriate olSpecMods objects). If fiber trunk redundancy is already configured, setting this object to a redundant state will remove the previous configuration. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The wrap state of this trunk. A trunk can wrap in response to a network event such as a break in the cable. Enumeration: 'wrapped': 1, 'unwrapped': 2.

The upstream or downstream neighbor of the trunk. Enumeration: 'slot-11': 11, 'slot-10': 10, 'slot-13': 13, 'slot-12': 12, 'slot-15': 15, 'slot-14': 14, 'slot-17': 17, 'slot-16': 16, 'slot-5': 5, 'slot-4': 4, 'slot-7': 7, 'slot-6': 6, 'slot-1': 1, 'external': 256, 'slot-3': 3, 'slot-2': 2, 'slot-9': 9, 'slot-8': 8.

A table that contains information about each 50nnM-CTL in the concentrator. Note, current architecture will limit the number of instances to one per concentrator.

A list of information for each 50nnM-CTL module in the concentrator.

The slot number for this module.

The temperature as detected by the probes on this module. Enumeration: 'extremeTemp': 2, 'okay': 1.

A table that contains module information about each EMM module in the concentrator.

A list of module information for a particular EMM module in the concentrator.

The slot number of this module.

The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive unless the reset mastership command is used. Enumeration: 'seven': 7, 'ten': 10, 'nine': 9, 'six': 6, 'three': 3, 'two': 2, 'four': 4, 'five': 5, 'eight': 8, 'one': 1.

The mastership status of this agent. Enumeration: 'non-master': 2, 'master': 1, 'electing': 3.

A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1. Note that EMMs before v3.0 will have 00-00-00-00-00-00 as their station address.

A table of information that contains port-specific information for each port on each 51nnM-MGT module.

A list of information about a specific port on a 51nnM-MGT module.

The slot number of this port's module.

The port number of this port.

The IP Address associated with this port.

A table of module-specific information for each 51nnM-FIB module in the concentrator.

A list of module-specific information associated with a particular 51nnM-FIB module in the concentrator.

The slot number of this module.

The network indicated by the module's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

The current state of this module's low light warning configuration. Enabling this feature causes the module to check for low light and to issue a warning if low light is present. Disabling low light has the advantage of faster redundancy switchover in the event of a port error. Enumeration: 'disabled': 2, 'enabled': 1.

The low light warning configuration indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A table of port-specific information for each port of each 51nnM-FIB module.

A list of information about a specific port on a 51nnM-FIB module.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

A list of module-specific information associated with a particular 51nnM-UTP module in the concentrator.

A module entry containing objects that describe the module level for that particular module.

The slot number of this module.

The network indicated by the module's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

The current state of this module's crossover configuration. Setting this object to uncrossed(2) allows the last port to be used to connect to another repeater. Often this feature is used to connect one 10BASE-T module to another. Enumeration: 'uncrossed': 2, 'crossed': 1.

The crossover configuration indicated by this module's dip switches. Enumeration: 'uncrossed': 2, 'crossed': 1.

The number of bits to store in the repeater's fifo buffer. See the module user's guide for more information. Enumeration: 'seven-bits': 2, 'eight-bits': 1.

The fifo fill level as indicated by this module's dip switches. Enumeration: 'seven-bits': 2, 'eight-bits': 1.

A table of port-specific information for each port of this module type.

A port entry containing objects that describe this port.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The port's link integrity configuration. Enabling link integrity configures the port to conform to the link integrity feature as specified by 10BASE-T. Enumeration: 'disabled': 2, 'enabled': 1.

The link integrity configuration as indicated by this port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The port's squelch configuration. See the module's user's guide for more information. Enumeration: 'low': 2, 'normal': 1.

The port's squelch configuration as indicated by this port's dip switches. Enumeration: 'low': 2, 'normal': 1.

A table of module-specific information for each 51nnM-TP module in the concentrator.

A list of module-specific information about a specific 51nnM-TP module in the concentrator.

The slot number of this module.

The network indicated by the module's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

The current state of this module's crossover configuration. Setting this object to uncrossed(2) allows the last port to be used to connect to another repeater. Often this feature is used to connect one 10BASE-T module to another. Enumeration: 'uncrossed': 2, 'crossed': 1.

The crossover configuration indicated by this module's dip switches. Enumeration: 'uncrossed': 2, 'crossed': 1.

A table of port-specific information for each port of this module type.

A port entry containing objects that describe this port.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The port's link integrity configuration. Enabling link integrity configures the port to conform to the link integrity feature as specified by 10BASE-T. Enumeration: 'disabled': 2, 'enabled': 1.

The link integrity configuration as indicated by this port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The port's squelch configuration. See the module's user's guide for more information. Enumeration: 'low': 2, 'normal': 1.

The port's squelch configuration as indicated by this port's dip switches. Enumeration: 'low': 2, 'normal': 1.

A list of module-specific information associated with a particular 51nnM-BNC module in the concentrator.

A module entry containing objects that describe the module level for that particular module.

The slot number of this module.

The network indicated by the module's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

A table of port-specific information for each port of this module type.

A port entry containing objects that describe this port.

The slot number of this port's module.

The port number of this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The state of this port's termination as indicated by the port's dip switches. Enumeration: 'terminated': 1, 'not-terminated': 2.

The state of this port's ground as indicated by the port's dip switches. Enumeration: 'not-grounded': 2, 'grounded': 1.

A table of module-specific information for each 51nnB-EE module in the concentrator.

A list of module-specific information about a specific 51nnB-EE module in the concentrator.

The slot number of this module.

A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1.

A textual description of the protocols supported by this module

A table of port-specific for each port of each 51nnB-EE module in the concentrator.

A list of port-specific informatoin about a specific 51nnB-EE port in the concentrator.

The slot number for this port's module.

The port number for this port within this slot.

The IP Address associated with this port.

The network for this port as specified by this port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2, 'front-panel': 5.

The network for this port as specified by the OEBM's non-volatile storage. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2, 'front-panel': 5.

A table of module-specific information for each 51nnR-ES module in the concentrator.

A list of module-specific information about a specific 51nnR-ES module in the concentrator.

The slot number of this module.

A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1.

A textual description of the protocols supported by this module

A table of port-specific for each port of each 51nnR-ES module in the concentrator.

A list of port-specific informatoin about a specific 51nnR-ES port in the concentrator.

The slot number for this port's module.

The port number for this port.

The IP Address associated with this port.

The network for this port as specified by this port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2, 'front-panel': 5.

The network for this port as specified by the OERM's non-volatile storage. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2, 'front-panel': 5.

A table of module-specific information for each 51nnR-EE module in the concentrator.

A list of module-specific information about a specific 51nnR-EE module in the concentrator.

The slot number of this module.

A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1.

A textual description of the protocols supported by this module

A table of port-specific for each port of each 51nnR-EE module in the concentrator.

A list of port-specific informatoin about a specific 51nnR-EE port in the concentrator.

The slot number for this port's module.

The port number of this port.

The IP Address associated with this port.

The network for this port as specified by this port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2, 'front-panel': 5.

The network for this port as specified by the OERM's non-volatile storage. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2, 'front-panel': 5.

A list of module-specific information associated with a particular 51nnM-AUIF module in the concentrator.

A list of module-specific information about a specific 51nnM-AUIF module in the concentrator.

The slot number of this module.

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 51nnM-AUIF port in the concentrator.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The network indicated by the port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

A list of module-specific information associated with a particular 51nnM-AUIM module in the concentrator.

A list of module-specific information about a specific 51nnM-AUIM module in the concentrator.

The slot number of this module.

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 51nnM-AUIM port in the concentrator.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The network indicated by the port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

The current SQE test configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The SQE test configuration for this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The current collision configuration for this port. Enumeration: 'alternate': 2, 'normal': 1.

The collision configuration for this port as indicated by the port's dip switches. Enumeration: 'alternate': 2, 'normal': 1.

The current step configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The step configuration for this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module-specific information associated with a particular 5208M-TP module in the concentrator.

A description of the 5208M-TP module attributes.

The slot number of this module.

The desired state of this module with respect to the ring. Setting this attribute to bypass(2) will cause this module to be removed from the ring that passes through the module's ring in and ring out ports. Enumeration: 'insert': 1, 'bypass': 2.

The operational state of this module with respect to the ring. If this attribute is equal to bypass(2), then the module has been removed from the ring that passes through the module's ring in and ring out ports. Enumeration: 'insert': 1, 'bypass': 2.

The setting of this module's port impedance matching, with 100 ohm corresponding to unshielded twisted pair cabling and 150 ohm corresponding to shielded twisted pair cabling. This setting is valid for all ports on this module. Enumeration: 'ohm100': 1, 'ohm150': 2.

A table of port-specific information for each port of this module type.

A description of 5208M-TP port attributes.

The slot number of this port's module.

The port number of this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

Determines whether the station connected to this port has a MAC address. Enumeration: 'mac-not-present': 2, 'mac-present': 1.

A list of trunk-specific information about each trunk for this module type.

A description of 5208M-TP trunk attributes.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.

The trunk number for this trunk.

The state of this trunk as indicated by the trunk's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The cable monitor configuration for this trunk. Enumeration: 'disabled': 2, 'notApplicable': 3, 'enabled': 1.

The cable monitor configuration as indicated by this trunk's dip switches. Enumeration: 'disabled': 2, 'notApplicable': 3, 'enabled': 1.

The map state of the copper ring-in trunk. This should be set to external for ring-in trunks which connect to external hubs. The mapping logic will not operate on trunks which are set to external. This prevents incorrect mapping which can occur when a module in one hub detects the mapping signal from another hub. This attribute only applies to copper ring-in trunks. Enumeration: 'notApplicable': 1, 'internal': 2, 'external': 3.

Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for trunks which connect to hubs which perform beacon recovery. This attribute is used to determine the fault domain when resolving a beaconing condition. The beacon recovery process will resolve beaconing on trunks with this attribute set to nonExists(2) before trunks with the attribute set to exists(1) are resolved. For backplane trunks, setting to a value other than notApplicable will return invalidData error. The default value is nonExists(2). Enumeration: 'nonExists': 2, 'notApplicable': 3, 'exists': 1.

A list of module-specific information associated with a particular 51nnM-FP module in the concentrator.

A list of module-specific information about a specific 51nnM-FP module in the concentrator.

The slot number of this module.

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 51nnM-FP port in the concentrator.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The network indicated by the port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

The current low light warning configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The low light warning configuration indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The current high power optic configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The high power optic configuration for this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module-specific information associated with a particular 51nnM-FBP module in the concentrator.

A list of module-specific information about a specific 51nnM-FBP module in the concentrator.

The slot number of this module.

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 51nnM-FBP port in the concentrator.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The network indicated by the port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

The current low light warning configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The low light warning configuration indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The current high power optic configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The high power optic configuration for this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module-specific information associated with a particular 51nnM-TPL module in the concentrator.

A list of module-specific information about a specific 51nnM-TPL module in the concentrator.

The slot number of this module.

The network indicated by the module's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 51nnM-TPL port in the concentrator.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1, 'remote-diagnostics': 8.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the slot index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the port index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The current link integrity configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The link integrity configuration as indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The current squelch configuration for this port. See the module's user's guide for more information. Enumeration: 'low': 2, 'normal': 1.

The current receive jabber configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The receive jabber configuration as indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module-specific information about a specific 51nnM-TPPL module in the concentrator.

A list of module-specific information about a specific 51nnM-TPPL module in the concentrator.

The slot number of this module.

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 51nnM-TPPL port in the concentrator.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1, 'remote-diagnostics': 8.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the slot index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the port index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The network indicated by the port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

The current link integrity configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The link integrity configuration as indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The current squelch configuration for this port. See the module's user's guide for more information. Enumeration: 'low': 2, 'normal': 1.

The current receive jabber configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The receive jabber configuration as indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module-specific information about a specific 52nnM-TP module in the concentrator.

A description of the 52nnM-TP module attributes.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.

The ring's bandwidth. Enumeration: 'sixteenMegabit': 2, 'fourMegabit': 1.

The dip switch setting for the ring's bandwidth. Enumeration: 'sixteenMegabit': 2, 'fourMegabit': 1.

The setting of this module's port impedance matching, with 100 ohm corresponding to unshielded twisted pair cabling and 150 ohm corresponding to shielded twisted pair cabling. This setting is valid for all ports on this module. Enumeration: 'ohm100': 1, 'ohm150': 2.

The dip switch setting for the module's port impedance matching. Enumeration: 'ohm100': 1, 'ohm150': 2.

A table of port-specific information for each port of this module type.

A description of 52nnM-TP port attributes.

The slot number of this port's module.

The port number of this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

Determines whether the station connected to this port has a MAC address. Enumeration: 'mac-not-present': 2, 'mac-present': 1.

A list of trunk-specific information about each trunk for this module type.

A description of 52nnM-TP trunk attributes.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.

The trunk number for this trunk.

The state of this trunk as indicated by the trunk's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module-specific information about a specific 52nnM-FR module in the concentrator.

A description of the 52nnM-FR module attributes.

The slot number of this module.

The ring's bandwidth. Enumeration: 'sixteenMegabit': 2, 'fourMegabit': 1.

The dip switch setting for the ring's bandwidth. Enumeration: 'sixteenMegabit': 2, 'fourMegabit': 1.

A table of port-specific information for each port of this module type.

A description of 52nnM-FR port attributes.

The slot number of this port's module.

The port number of this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The setting of this port's impedance matching, with 100 ohm corresponding to unshielded twisted pair cabling and 150 ohm corresponding to shielded twisted pair cabling. Enumeration: 'ohm100': 1, 'ohm150': 2.

Determines whether the station connected to this port has a MAC address. Enumeration: 'mac-not-present': 2, 'mac-present': 1.

A list of trunk-specific information about each trunk for this module type.

A description of 52nnM-FR trunk attributes.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.

The trunk number of this trunk.

The state of this trunk as indicated by the trunk's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The cable monitor configuration for this trunk. This does not apply to fiber trunks. Enumeration: 'disabled': 2, 'notApplicable': 3, 'enabled': 1.

The cable monitor configuration as indicated by this trunk's dip switches. This does not apply to fiber trunks. Enumeration: 'disabled': 2, 'notApplicable': 3, 'enabled': 1.

The compatibility mode for this trunk. This only applies to fiber trunks. Enumeration: 'disabled': 2, 'notApplicable': 3, 'enabled': 1.

The compatibility mode as indicated by this trunk's dip switches. This only applies to fiber trunks. Enumeration: 'disabled': 2, 'notApplicable': 3, 'enabled': 1.

The map state of the copper ring-in trunk. This should be set to external for ring-in trunks which connect to external hubs. The mapping logic will not operate on trunks which are set to external. This prevents incorrect mapping which can occur when a module in one hub detects the mapping signal from another hub. This attribute only applies to copper ring-in trunks. Enumeration: 'notApplicable': 1, 'internal': 2, 'external': 3.

Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for trunks which connect to hubs which perform beacon recovery. This attribute is used to determine the fault domain when resolving a beaconing condition. The beacon recovery process will resolve beaconing on trunks with this attribute set to nonExists(2) before trunks with the attribute set to exists(1) are resolved. For backplane trunks, setting to a value other than notApplicable will return invalidData error. The default value is nonExists(2). Enumeration: 'nonExists': 2, 'notApplicable': 3, 'exists': 1.

The slot index of the redundant trunk's buddy. To set a trunk to be redundant, the buddy's slot must be set to a valid value. This object is applicable to fiber trunks only. This value is only considered valid if the corresponding TrunkAdminState object for this trunk is configured for redundancy. Copper and backplane trunks will return invdata(6). If both the ring-in and ring-out trunks of a module are configured for redundancy, they must both be redundant to the same module. The buddy slot object for this slot is automatically set to this trunk.

The desired state of this trunk. Enabling a trunk allows the trunk to pass network traffic. This object may be used to configure fiber trunk redundancy. Setting a trunk to be redundant-primary(3) or redundant-backup(4) requires that the ol52nnMFRTrunkBuddySlot object be set to a valid value. If fiber trunk redundancy is already configured, setting this object to a redundant state will remove the previous configuration. Enumeration: 'disabled': 2, 'redundant-primary': 3, 'enabled': 1, 'redundant-standby': 4.

A table of module-specific information for each 51nnM-TS module in the concentrator.

A list of module information for each 51nnM-TS module in the concentrator.

The slot number of this module.

A textual description of the protocols supported by this module

The IP Address of the terminal server.

The TCP port number of the the terminal server's remote console port.

A 6 octet address that uniquely identifies this module. The station address is the mac address of the terminal server.

The network indicated by the module's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

The terminal server's CPU revision.

A table of information that contains port-specific information for each port on each 51nnM-TS module.

A list of information about a specific port on a 51nnM-TS module.

The slot number for this port.

The port number of this port.

The administrative state of this port. Enumeration: 'disabled': 2, 'local': 6, 'enabled': 1, 'remote': 7.

The operational mode of this port. Enumeration: 'connected': 3, 'idle': 1, 'local': 2.

A table of module-specific information for each 51nnM-FL module in the concentrator.

A list of module-specific information associated with a particular 51nnM-FL module in the concentrator.

The slot number of this module.

The network indicated by the module's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

A table of port-specific information for each port of each 51nnM-FL module.

A list of information about a specific port on a 51nnM-FL module.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.

The port number of this port.

The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return invalidData error. Remote Failure Signaling (RFS), is set on connected module port to permit transmit error detection on local port. Port must be set to be RFS when connected port is set to be redundant Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1, 'redundant-rfs': 5.

The slot index of the redundant port's buddy.

The port index of the redundant port's buddy.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1, 'redundant-rfs': 5.

A table that contains information about each 50nnM-RCTL in the concentrator.

A list of information for each 50nnM-RCTL module in the concentrator.

The slot number for this module.

The operational state of the 50nnM-RCTL module. Specifically, this is an indicator of whether the 50nnM-RCTL module is providing clock signals to the backplane. An active 50nnM-RCTL module provides clock signals to the backplane while a standby 50nnM-RCTL module does not. Note that only one 50nnM-RCTL module will be active at any given time; all other 50nnM-RCTL modules in the concentrator will be in standby mode. Enumeration: 'active': 1, 'standby': 2.

The current status of the on-board clocks on this module. Enumeration: 'faulty': 2, 'okay': 1.

The temperature as detected by the probe on this module. Enumeration: 'extremeTemp': 2, 'okay': 1.

A list of module-specific information associated with a particular 51nnM-FB module in the concentrator.

A list of module-specific information about a specific 51nnM-FB module in the concentrator.

The slot number of this module.

The network indicated by the module's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

The current state of this module's low light warning configuration. Enabling this feature causes the module to check for low light and to issue a warning if low light is present. Disabling low light has the advantage of faster redundancy switchover in the event of a port error. Enumeration: 'disabled': 2, 'enabled': 1.

The low light warning configuration indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 51nnM-FB port in the concentrator.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module attributes that apply to this model. To access an ol53nnMMGTModTable entry, the ol53nnMMGTModSlotIndex attribute is used.

A list of module-specific information about a specific 53nnM-MGT module in the concentrator.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.

The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive unless the reset mastership command is used. Enumeration: 'seven': 7, 'ten': 10, 'nine': 9, 'six': 6, 'three': 3, 'two': 2, 'four': 4, 'five': 5, 'eight': 8, 'one': 1.

The mastership status of this agent. Enumeration: 'non-master': 2, 'master': 1, 'electing': 3.

A 6 octet address that uniquely identifies this module. The station address is the MAC address of port 1.

The IP address associated with this module.

Down stream MAC

Up stream MAC

The FDDI path which should be inserted into the MAC Enumeration: 'primary': 1, 'secondary': 2.

Down stream slot (transmit to)

Up stream slot (receive from)

Transmit DBA (debug only) Enumeration: 'fddi-path-1': 24, 'fddi-path-3': 26, 'fddi-path-2': 25, 'fddi-path-5': 28, 'fddi-path-4': 27, 'fddi-path-7': 30, 'fddi-path-6': 29, 'fddi-path-8': 31, 'isolated': 2.

Receive DBA (debug only) Enumeration: 'fddi-path-1': 24, 'fddi-path-3': 26, 'fddi-path-2': 25, 'fddi-path-5': 28, 'fddi-path-4': 27, 'fddi-path-7': 30, 'fddi-path-6': 29, 'fddi-path-8': 31, 'isolated': 2.

An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only)

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 53nnM-MGT port in the concentrator.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.

A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortIndex.

Specifies the FDDI port type (a or b). Enumeration: 'a': 1, 'b': 2.

(refer to ANSI SMT 9.6.2). Enumeration: 'pc8': 9, 'pc9': 10, 'pc2': 3, 'pc3': 4, 'pc0': 1, 'pc1': 2, 'pc6': 7, 'pc7': 8, 'pc4': 5, 'pc5': 6.

An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Withhold flag state. The supported values and their corresponding PCM states and PC-Withhold condition, when relevant, are: disabled: (PC0:Off, PC9:Maint) connecting: (PC1(Break) || PC3 (Connect) || PC4(next) || PC5 (Signal) || PC6(Join) || PC7 (Verify)) && (PC-Withhold = None) standby: (PC-Withhold != None) active: (PC2:Trace || PC8:Active) Enumeration: 'disabled': 1, 'standby': 3, 'connecting': 2, 'active': 4.

The type (PC-Neighbor) of the remote PORT that is determined in PC-Signaling in R-Val (1,2) (refer to ANSI SMT 9.6.3.2). Enumeration: 'a': 1, 'master': 4, 'b': 2, 'slave': 3, 'unknown': 5.

The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R-Val (9) (refer to ANSI SMT 9.6.3.2). Enumeration: 'false': 2, 'true': 1.

The Break State, BS-Flag (refer to ANSI SMT 9.4.3.4). Enumeration: 'false': 2, 'true': 1.

PC-Withhold, (refer to ANSI SMT 9.4.1). Enumeration: 'm-m': 2, 'none': 1, 'other': 3.

This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value). Enumeration: 'bad': 1, 'okay': 2.

FDDI module specific trunk table variables. At present there are none.

A description of 53nnM-MGT trunk attributes.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.

A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkIndex.

A list of module attributes that apply to this model. To access an ol53nnMFBMICModTable entry, the ol53nnMFBMICModSlotIndex attribute is used.

A list of module-specific information about a specific 53nnM-FBMIC module in the concentrator.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.

Down stream slot (transmit to)

Up stream slot (receive from)

Transmit DBA (debug only) Enumeration: 'fddi-path-1': 24, 'fddi-path-3': 26, 'fddi-path-2': 25, 'fddi-path-5': 28, 'fddi-path-4': 27, 'fddi-path-7': 30, 'fddi-path-6': 29, 'fddi-path-8': 31, 'isolated': 2.

Receive DBA (debug only) Enumeration: 'fddi-path-1': 24, 'fddi-path-3': 26, 'fddi-path-2': 25, 'fddi-path-5': 28, 'fddi-path-4': 27, 'fddi-path-7': 30, 'fddi-path-6': 29, 'fddi-path-8': 31, 'isolated': 2.

An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only)

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 53nnM-FBMIC port in the concentrator.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.

A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortIndex.

Specifies the FDDI port type. If the port is on an FFM, the only allowed values are slave(3), and master(4). In addition, there can only be one active slave port on any concentrator FDDI network. Enumeration: 'master': 4, 'slave': 3.

(refer to ANSI SMT 9.6.2). Enumeration: 'pc8': 9, 'pc9': 10, 'pc2': 3, 'pc3': 4, 'pc0': 1, 'pc1': 2, 'pc6': 7, 'pc7': 8, 'pc4': 5, 'pc5': 6.

An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Withhold flag state. The supported values and their corresponding PCM states and PC-Withhold condition, when relevant, are: disabled: (PC0:Off, PC9:Maint) connecting: (PC1(Break) || PC3 (Connect) || PC4(next) || PC5 (Signal) || PC6(Join) || PC7 (Verify)) && (PC-Withhold = None) standby: (PC-Withhold != None) active: (PC2:Trace || PC8:Active) Enumeration: 'disabled': 1, 'standby': 3, 'connecting': 2, 'active': 4.

The type (PC-Neighbor) of the remote PORT that is determined in PC-Signaling in R-Val (1,2) (refer to ANSI SMT 9.6.3.2). Enumeration: 'a': 1, 'master': 4, 'b': 2, 'slave': 3, 'unknown': 5.

The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R-Val (9) (refer to ANSI SMT 9.6.3.2). Enumeration: 'false': 2, 'true': 1.

The Break State, BS-Flag (refer to ANSI SMT 9.4.3.4). Enumeration: 'false': 2, 'true': 1.

PC-Withhold, (refer to ANSI SMT 9.4.1). Enumeration: 'm-m': 2, 'none': 1, 'other': 3.

This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value). Enumeration: 'bad': 1, 'okay': 2.

FDDI module specific trunk table variables. At present there are none.

A description of 53nnM-FBMIC trunk attributes.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.

A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkIndex.

A list of module attributes that apply to this model. To access an ol53nnMFIBSTModTable entry, the ol53nnMFIBSTModSlotIndex attribute is used.

A list of module-specific information about a specific 53nnM-FIBST module in the concentrator.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.

Down stream slot (transmit to)

Up stream slot (receive from)

Transmit DBA (debug only) Enumeration: 'fddi-path-1': 24, 'fddi-path-3': 26, 'fddi-path-2': 25, 'fddi-path-5': 28, 'fddi-path-4': 27, 'fddi-path-7': 30, 'fddi-path-6': 29, 'fddi-path-8': 31, 'isolated': 2.

Receive DBA (debug only) Enumeration: 'fddi-path-1': 24, 'fddi-path-3': 26, 'fddi-path-2': 25, 'fddi-path-5': 28, 'fddi-path-4': 27, 'fddi-path-7': 30, 'fddi-path-6': 29, 'fddi-path-8': 31, 'isolated': 2.

An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only)

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 53nnM-FIBST port in the concentrator.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.

A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortIndex.

Specifies the FDDI port type. If the port is on an FFM, the only allowed values are slave(3) and master(4). In addition, there can only be one active slave port on any concentrator FDDI network. Enumeration: 'master': 4, 'slave': 3.

(refer to ANSI SMT 9.6.2). Enumeration: 'pc8': 9, 'pc9': 10, 'pc2': 3, 'pc3': 4, 'pc0': 1, 'pc1': 2, 'pc6': 7, 'pc7': 8, 'pc4': 5, 'pc5': 6.

An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Withhold flag state. The supported values and their corresponding PCM states and PC-Withhold condition, when relevant, are: disabled: (PC0:Off, PC9:Maint) connecting: (PC1(Break) || PC3 (Connect) || PC4(next) || PC5 (Signal) || PC6(Join) || PC7 (Verify)) && (PC-Withhold = None) standby: (PC-Withhold != None) active: (PC2:Trace || PC8:Active) Enumeration: 'disabled': 1, 'standby': 3, 'connecting': 2, 'active': 4.

The type (PC-Neighbor) of the remote PORT that is determined in PC-Signaling in R-Val (1,2) (refer to ANSI SMT 9.6.3.2). Enumeration: 'a': 1, 'master': 4, 'b': 2, 'slave': 3, 'unknown': 5.

The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R-Val (9) (refer to ANSI SMT 9.6.3.2). Enumeration: 'false': 2, 'true': 1.

The Break State, BS-Flag (refer to ANSI SMT 9.4.3.4). Enumeration: 'false': 2, 'true': 1.

PC-Withhold, (refer to ANSI SMT 9.4.1). Enumeration: 'm-m': 2, 'none': 1, 'other': 3.

This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value). Enumeration: 'bad': 1, 'okay': 2.

FDDI module specific trunk table variables. At present there are none.

A description of 53nnM-FIBST trunk attributes.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.

A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkIndex.

A list of module attributes that apply to this model. To access an ol53nnMSTPModTable entry, the ol53nnMSTPModSlotIndex attribute is used.

A list of module-specific information about a specific 53nnM-STP module in the concentrator.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.

Down stream slot (transmit to)

Down stream slot (receive from)

transmit DBA (debug only) Enumeration: 'fddi-path-1': 24, 'fddi-path-3': 26, 'fddi-path-2': 25, 'fddi-path-5': 28, 'fddi-path-4': 27, 'fddi-path-7': 30, 'fddi-path-6': 29, 'fddi-path-8': 31, 'isolated': 2.

receive DBA (debug only) Enumeration: 'fddi-path-1': 24, 'fddi-path-3': 26, 'fddi-path-2': 25, 'fddi-path-5': 28, 'fddi-path-4': 27, 'fddi-path-7': 30, 'fddi-path-6': 29, 'fddi-path-8': 31, 'isolated': 2.

An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only)

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 53nnM-STP port in the concentrator.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.

A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortIndex.

Specifies the FDDI port type. If the port is on an FFM, the only allowed values are slave(3) and master(4). In addition, there can only be one active slave port on any concentrator FDDI network. Enumeration: 'master': 4, 'slave': 3.

(refer to ANSI SMT 9.6.2). Enumeration: 'pc8': 9, 'pc9': 10, 'pc2': 3, 'pc3': 4, 'pc0': 1, 'pc1': 2, 'pc6': 7, 'pc7': 8, 'pc4': 5, 'pc5': 6.

An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Withhold flag state. The supported values and their corresponding PCM states and PC-Withhold condition, when relevant, are: disabled: (PC0:Off, PC9:Maint) connecting: (PC1(Break) || PC3 (Connect) || PC4(next) || PC5 (Signal) || PC6(Join) || PC7 (Verify)) && (PC-Withhold = None) standby: (PC-Withhold != None) active: (PC2:Trace || PC8:Active) Enumeration: 'disabled': 1, 'standby': 3, 'connecting': 2, 'active': 4.

The type (PC-Neighbor) of the remote PORT that is determined in PC-Signaling in R-Val (1,2) (refer to ANSI SMT 9.6.3.2). Enumeration: 'a': 1, 'master': 4, 'b': 2, 'slave': 3, 'unknown': 5.

The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R-Val (9) (refer to ANSI SMT 9.6.3.2). Enumeration: 'false': 2, 'true': 1.

The Break State, BS-Flag (refer to ANSI SMT 9.4.3.4). Enumeration: 'false': 2, 'true': 1.

PC-Withhold, (refer to ANSI SMT 9.4.1). Enumeration: 'm-m': 2, 'none': 1, 'other': 3.

This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value). Enumeration: 'bad': 1, 'okay': 2.

Specifies the physical signaling used by the port, the only valid values are sddi(3) and tpddi(4). Enumeration: 'tpddi': 2, 'sddi': 1.

FDDI module specific trunk table variables. At present there are none.

A description of 53nnM-STP trunk attributes.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.

A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkIndex.

A list of module-specific information about a specific 51nnM-TPCL module in the concentrator.

A list of module-specific information about a specific 51nnM-TPCL module in the concentrator.

The slot number of this module.

When both connectors are on the same network: Setting this object to connector-1 allows the EMM to monitor the port statistics of port 1-12 on a per-port basis, and the port statistics of port 13-24 are summed and are reported through port 13. Setting this object to connector-2 allows the EMM to monitor the port statistics of port 12-24 on a per-port basis, and the port statistics of port 1-12 are summed and are reported through port 13. Note: when the 2 connectors are on different networks, setting this object to the value connector-1 or connector-2 will not have any effect. The port counters will be cleared whenever the value of this object is changed. Enumeration: 'connector-1': 1, 'connector-2': 2.

The network that this connector is attached to. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated-1': 21, 'isolated-2': 22.

The network that this connector is attached to. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated-1': 21, 'isolated-2': 22.

The network indicated by the connector dip switch. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated-1': 21, 'isolated-2': 22.

The network indicated by the connector dip switch. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated-1': 21, 'isolated-2': 22.

This object holds the consecutive collision count limit value. The module goes into the auto-partition mode whenever the consecutive collision count exceeds the consecutive collision limit count. Enumeration: 'collisions-63': 2, 'collisions-31': 1, 'collisions-255': 4, 'collisions-127': 3.

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 51nnM-TPCL port in the concentrator.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1, 'remote-diagnostics': 8.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the slot index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the port index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The current link integrity configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The link integrity configuration as indicated by this dip switch. Enumeration: 'disabled': 2, 'enabled': 1.

A table of module-specific information for each 52nnB-TT module in the concentrator.

A list of module-specific information about a specific 52nnB-TT module in the concentrator.

The slot number of this module.

Whether the bridge is a source-routing bridge or a source-routing-transparent bridge. Enumeration: 'bridge-type-sr': 1, 'bridge-type-srt': 2.

The version number of the software loaded into the module's flash chips.

The module's source routing bridge number.

The status of the ring containing this module. Enumeration: 'okay': 1, 'beaconing': 3, 'closed': 2.

A table of port-specific for each port of each 52nnB-TT module i the concentrator.

A list of port-specific information about a specific 52nnB-TT port in the concentrator.

The slot number for this port's module.

The port number for this port within this slot.

The port connector. Notice that setting port connector available only for the front pannel port. Enumeration: 'backPlane': 1, 'rj45': 8, 'db-9': 10.

The port connector. Notice that setting port connector available only for the front pannel port. Enumeration: 'off': 6, 'listening': 3, 'disabled': 1, 'learning': 4, 'forwarding': 5, 'blocking': 2.

The IP address associated with this port.

A 6 octet address that uniquely identifies this port.

Port throughput measured in Kbytes per second.

Port forwarding rate measured in frames per second.

The port's source routing ring number.

The ring's bandwidth. Enumeration: 'sixteenMegabit': 2, 'fourMegabit': 1.

A table that contains trunk-specific information for each trunk on each 52nnB-TT in the concentrator.

A list of information about a specific Trunk on a 52nnB-TT module in the concentrator.

The slot number of this module. Its value ranges between 1 and olConcNumSlots.

The trunk number of this module. Its value ranges between 1 and olModNumTrunks.

A table of module-specific information for each 51nnI-x module in the concentrator.

A list of module-specific information about a specific 51nnI-x module in the concentrator.

The slot number of this module.

The software currently loaded and executing has the module operating as a Bridge, Switch or Router. Enumeration: 'bridge': 1, 'switch': 2, 'router': 3.

A 6 octet address that uniquely identifies this module. The station address is the mac address of port 1.

The current module configuration with respect to default PROM values as specified by dip switches. Enumeration: 'false': 2, 'true': 1.

A textual description of the protocols supported by this module

A table of port-specific information for each port of each 51nnI-x module in the concentrator.

A list of port-specific information about a specific 51nnI-x port in the concentrator.

The slot number for this port's module.

The port number for this port within this slot.

The state of this port as indicated by the port's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The current IEEE 802.1d Spanning Tree Algorithm and Protocol state (STAP) of this port. Enumeration: 'off': 6, 'listening': 3, 'unknown': 7, 'disabled': 1, 'learning': 4, 'forwarding': 5, 'blocking': 2.

The IP Address associated with this port.

The network for this port as specified by this port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2, 'front-panel': 5.

The network for this port as specified by the OEIM's non-volatile storage. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2, 'front-panel': 5.

A table that contains module information about each 52nnM-MGT in the concentrator.

A list of module information for each 52nnM-MGT in the concentrator.

The slot number of this module. Its value ranges between 1 and olConcNumSlots.

The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive unless the reset mastership command is used. Enumeration: 'seven': 7, 'ten': 10, 'nine': 9, 'six': 6, 'three': 3, 'two': 2, 'four': 4, 'five': 5, 'eight': 8, 'one': 1.

The mastership status of this agent. Enumeration: 'non-master': 2, 'master': 1, 'electing': 3.

A 6 octet address that uniquely identifies this module. The station address is the MAC address of port 1.

The ring's bandwidth. Enumeration: 'sixteenMegabit': 2, 'fourMegabit': 1.

The status of the ring containing this module. Enumeration: 'okay': 1, 'beaconing': 3, 'closed': 2.

The network that this module should assign itself to upon becoming master if the module was previously a slave. no-change(25) indicates that the module should not change its current network assignment. Enumeration: 'token-ring-1': 9, 'token-ring-3': 11, 'token-ring-2': 10, 'token-ring-5': 13, 'token-ring-4': 12, 'token-ring-7': 15, 'token-ring-6': 14, 'isolated': 2, 'no-change': 25.

A MAC address with the locally administered bit set to one. Setting this value to an invalid address will return invalidData error. An invalid address is a value with the locally administered bit set to zero, or a value of all ones.

The desired MAC address for this agent. burned-in(1) indicates that the factory setting as defined in ol52nnMMGTModStationAddr should be used. locally-administered(2) indicates that the MAC address set in ol52nnMMGTModLocalMACAddress should be used. This change will take effect following a reset of the agent. The actual MAC address in use is defined in ol52nnMMGTModActiveMACAddress. Setting this value to use an invalid MAC address (for example, all zeros) will return invalidData error. Enumeration: 'burned-in': 1, 'locally-administered': 2.

A actual MAC address that is being used by this agent. This is the MAC address of port 1.

A table that contains port-specific information for each port on each 52nnM-MGT in the concentrator.

A list of information about a specific port on a 52nnM-MGT module in the concentrator.

The slot number of this port's module.

The port number of this port.

The IP address associated with this port.

A table that contains trunk-specific information for each trunk on each 52nnM-MGT in the concentrator.

A list of information about a specific Trunk on a 52nnM-MGT module in the concentrator.

The slot number of this module. Its value ranges between 1 and olConcNumSlots.

The slot number of this module. Its value ranges between 1 and olModNumTrunks.

The cable monitor configuration for this trunk. Enumeration: 'notApplicable': 3, 'enable': 1, 'disable': 2.

The map state of the copper ring-in trunk. This should be set to external for ring-in trunks which connect to external hubs. The mapping logic will not operate on trunks which are set to external. This prevents incorrect mapping which can occur when a module in one hub detects the mapping signal from another hub. This attribute only applies to copper ring-in trunks. Enumeration: 'notApplicable': 1, 'internal': 2, 'external': 3.

Indicates whether the trunk is connected to a segment that will perform beacon recovery. This should be set to exists(1) for trunks which connect to hubs which perform beacon recovery. This attribute is used to determine the fault domain when resolving a beaconing condition. The beacon recovery process will resolve beaconing on trunks with this attribute set to nonExists(2) before trunks with the attribute set to exists(1) are resolved. For backplane trunks, setting to a value other than notApplicable will return invalidData error. The default value is nonExists(2). Enumeration: 'nonExists': 2, 'notApplicable': 3, 'exists': 1.

A table that contains information about each 50nnM-HCTL in the concentrator.

A list of information for each 50nnM-HCTL module in the concentrator.

The slot number for this module. The value should be 7.

The operational state of the 50nnM-HCTL module. Specifically, this is an indicator of whether the 50nnM-HCTL module is providing clock signals to the backplane. An active 50nnM-HCTL module provides clock signals to the backplane while a standby 50nnM-HCTL module does not. Note that only one 50nnM-HCTL module will be active at any given time; all other 50nnM-HCTL/ 50nnM-RCTL modules in the concentrator will be in standby mode. Enumeration: 'active': 1, 'standby': 2.

The current status of the on-board clocks on this module. Enumeration: 'faulty': 2, 'okay': 1.

The temperature as detected by the probe on this module. Enumeration: 'extremeTemp': 2, 'okay': 1.

Indicates whether this 6-slot concentrator contains a power distribution board that supports powersupply redundancy. Enumeration: 'notPresent': 2, 'present': 1.

The Ethernet channel 1 activity/collision LED configuration as indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The Ethernet channel 2 activity/collision LED configuration as indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

The Ethernet channel 3 activity/collision LED configuration as indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module-specific information associated with a particular 61nnM-CAR module in the concentrator.

A list of module-specific information about a specific 61nnM-CAR module in the concentrator.

The slot number of this module.

The subslot number of this module.

The software boot eprom version of this module.

A table that contains module information about each 60nnM-MGT module in the concentrator.

A list of module information for each 60nnM-MGT module in the concentrator.

The slot number of this module.

The subslot number of this module.

The software boot eprom version of this module.

The mastership priority of this agent. Ten is the highest and one is the lowest. Priority is only used when an election occurs. Mastership is not preemptive unless the reset mastership command is used. Enumeration: 'seven': 7, 'ten': 10, 'nine': 9, 'six': 6, 'three': 3, 'two': 2, 'four': 4, 'five': 5, 'eight': 8, 'one': 1.

The mastership status of this agent. Enumeration: 'non-master': 2, 'master': 1, 'electing': 3.

The Hub serial number mastership is presiding over. Zero length string for slaves.

A table that contains information about Ethernet Network Monitor Cards in the ONcore Hub.

A list of information for an Ethernet Network Monitor Card in the ONcore Hub.

The slot number of this card.

The subslot number of this card.

The software boot eprom version of this module.

The current IP address of this card and the associated interface.

The current subnet mask of this card and the associated interface.

The current default gateway of this card and the associated interface. Note that a value of 0.0.0.0 indicates that this interface is not con- configured to be used with a default gateway.

A 6 octet address that uniquely identifies this card. Note that an address of 00-00-00-00-00-00 is invalid and the module has failed.

The desired connectvity mode of this card. When this attribute is set to enabled(1) and the card is set to a network, it will forward messages to and from the master Distributed Management Module. If this attribute is set to disabled(2), the card may still collect statistics but not forward messages to and from the Distributed Management Module. If this attribute is set to standby(3), the card will not collect statistics or forward messages to/from the Distributed Management Module. Enumeration: 'disabled': 2, 'standby': 3, 'enabled': 1.

The desired RMON host staticstics mode of this card. When this attribute is set to enabled, the card will gather RMON host table statistics. Note that when this attribute is enabled, the accuracy of all statistics may be impaired during peak loads. Enumeration: 'disabled': 2, 'enabled': 1.

A table of port-specific information for each port of this module type.

A list of port specific information about this module's ports.

The slot number of the module assocaited with this port.

The port number with respect to the module it resides on.

The desired state of this port. Setting this port to redundant-primary or redundant-backup with invalid buddy slot or buddy port will result in an error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1.

The slot index of the redundant port's buddy port.

The port index of the redundant port's buddy. Valid ports are those ports which are not redundant. The buddy port admin state will be set to redundant.

The network indicated by the port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'ethernet-4': 32, 'ethernet-5': 33, 'ethernet-6': 34, 'ethernet-7': 35, 'ethernet-8': 36, 'isolated-1': 21.

The current port high power optics mode. Setting this variable to enable(1), will enable the port to drive up to 4K meter fiber cable. Enumeration: 'enable': 1, 'disable': 2.

A list of module specific information about this module.

Values to describe module specific inormation.

The slot index of this module.

The subslot index of this module. (e.g. mother boards have subslot index equals to one.

The software boot eprom version of this module.

The Non-Volatile RAM dip switch setting for this module. Setting this object to enable(1) will cause the module to be configured according to the configuration which was saved in the non-volatile storage. Enumeration: 'disabled': 2, 'enabled': 1.

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 61nnM-TPL port in the concentrator.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1, 'remote-diagnostics': 8.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the slot index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the port index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.

The network indicated by the port's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'ethernet-4': 32, 'ethernet-5': 33, 'ethernet-6': 34, 'ethernet-7': 35, 'ethernet-8': 36, 'isolated-1': 21.

The current link integrity configuration for this port. Setting this object to enabled(1) makes it conform to the 10BASE-T link integrity standard. Setting this object to disabled(2) makes it compatible with the older pre 10BASE-T module. Enumeration: 'disabled': 2, 'enabled': 1.

The current auto polarity configuration for this port. Setting this object to enabled(1) causes the module to switch the port polarity automatically when the port polarity is reverted. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module-specific information about a specific 61nnM-TPL module in the concentrator.

A list of module-specific information about a specific 61nnM-TPL module in the concentrator.

The slot number of this module.

The subslot number of this module.

The software boot eprom version of this module.

The Non-Volatile RAM dip switch setting for this module. Enabling this switch will cause the module to be configured according to the configurations that were saved in the non-volatile storage after the module reset. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module-specific information about a specific 51nnM-TPLS module in the concentrator.

A list of module-specific information about a specific 51nnM-TPLS module in the concentrator.

The slot number of this module.

The network indicated by the module's dip switches. Enumeration: 'ethernet-1': 6, 'ethernet-2': 7, 'ethernet-3': 8, 'isolated': 2.

This object holds the consecutive collision count limit value. The module goes into the auto-partition mode whenever the consecutive collision count exceeds this limit. Enumeration: 'collisions-63': 2, 'collisions-31': 1, 'collisions-255': 4, 'collisions-127': 3.

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 51nnM-TPLS port in the concentrator.

The slot number of this port's module.

The port number of this port.

The desired state of this port. Setting this port to be redundant or for remote diagnostics with invalid settings of buddy slot and buddy port will return the genError error. Enumeration: 'disabled': 2, 'redundant-backup': 4, 'redundant-primary': 3, 'enabled': 1, 'remote-diagnostics': 8.

The admin state of this port as indicated by the dip switches. i.e. This object indicates whether the port will initialize to enabled or disabled when the module configures itself from dips. Enumeration: 'disabled': 2, 'enabled': 1.

The security state of this port as indicated by the dip switches. i.e. This object indicates whether the port's security state will initialize to enabled (full security) or disabled (no security) when the module configures itself from dips. Enumeration: 'disabled': 2, 'enabled': 1.

The slot index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the slot index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.

The port index of the redundant port's buddy. To set a port to be redundant, the buddy's slot and port must be set to valid values. The buddy is automatically set to be redundant to this port. If the port is configured for remote diagnostics, then this contains the port index of the backup buddy port. To configure a port for remote diagnostics, the buddy's slot and port must be set to valid values.

The current link integrity configuration for this port. Enumeration: 'disabled': 2, 'enabled': 1.

The link integrity configuration as indicated by this module's dip switches. Enumeration: 'disabled': 2, 'enabled': 1.

A table that contains information about the Controller in the concentrator.

A list of information for the Controller module in the concentrator.

The slot number for this module. Note that this module will always be in slot 17.

The operational state of the Controller module. Specifically, this is an indicator of whether the Controller module is providing clock signals to the backplane. An active Controller module provides clock signals to the backplane while a standby Controller module does not. Note that only the active Controller is visible to an ONline agent; hence, this object will have the value active(1). Enumeration: 'active': 1, 'standby': 2.

The current status of the on-board clocks on this module. Enumeration: 'faulty': 2, 'okay': 1.

The overall temperature status for this concentrator as detected by this module. This object's value is an aggregate of all temperature probes located within this concentrator as sensed by this module. Hence, when at least one probe in the concentrator reports an extreme temperature, then this object will have the value extremeTemp(2). Enumeration: 'extremeTemp': 2, 'okay': 1.

A table that contains information about the Controller in the concentrator.

A list of information for the Controller module in the concentrator.

The slot number for this module.

The subslot number for this module.

The software boot eprom version of this module.

The operational state of the Controller module. Specifically, this is an indicator of whether the Controller module is providing clock signals to the backplane. An active Controller module provides clock signals to the backplane while a standby Controller module does not. Enumeration: 'active': 1, 'standby': 2.

The current status of the on-board clocks on this module. Enumeration: 'faulty': 2, 'okay': 1.

The overall temperature status for the concentrator as detected by this module. This object's value is an aggregate of all the temperature probes located within this concentrator as sensed by this module. Hence, when at least one probe in the concentrator reports an extreme temperature, then this object will have the value extremeTemp(2). Enumeration: 'extremeTemp': 2, 'okay': 1.

The current status of the on-board A/D converter. Typically, when this object has a value of faulty(2), it is because the value obtained from the A/D converter internal test channel is out of tolerance from what is specified by the manufacturer. Enumeration: 'faulty': 2, 'okay': 1.

The current status of powersupply 1. Enumeration: 'active': 1, 'faulty': 3, 'not-installed': 4.

The current status of powersupply 2. Enumeration: 'active': 1, 'faulty': 3, 'not-installed': 4.

The current status of powersupply 3. Enumeration: 'active': 1, 'faulty': 3, 'not-installed': 4.

The current status of powersupply 4. Enumeration: 'active': 1, 'faulty': 3, 'not-installed': 4.

A table that contains information about each Redundant Controller in the concentrator.

A list of information for each Load Sharing Redundant controller module in the concentrator.

The slot number for this module.

The operational state of the Load Sharing Redudant Controller module. Specifically, this is an indicator of whether the Load Sharing Redudant Controller module is providing clock signals to the backplane. An active Load Sharing Redudant Controller module provides clock signals to the backplane while a standby Load Sharing Redudant Controller module does not. Note that only one Load Sharing Redudant Controller module will be active at any given time; all other Load Sharing Redudant Controller modules in the concentrator will be in standby mode. Enumeration: 'active': 1, 'standby': 2.

The current status of the on-board clocks on this module. Enumeration: 'faulty': 2, 'okay': 1.

The temperature as detected by the probe on this module. Enumeration: 'extremeTemp': 2, 'okay': 1.

A list of module-specific information associated with a particular ol41nnHMTP or ol41nnHMTP-FL module.

A module entry containing objects that describe the module level for that particular module.

The slot number of this module.

The serial number of this module, as entered by the user through the Management interface.

A list of the various protocols supported by the module's agent.

The IP Address of this module.

A table of port-specific information for each port of this module type.

A port entry containing objects that describe this port.

The slot (stack) number of this port's module.

The port number of this port.

Used to reset the port's '802.3 state machine', which will re-enable a disabled port and/or reconnect a partitioned port. Enumeration: 'reset': 2, 'noReset': 1.

The port's (good) link integrity configuration. Enabling link integrity configures the port to conform to the link integrity feature as specified by 10BASE-T. Applicable only to 10BASE-T ports. Enumeration: 'disabled': 2, 'notApplicable': 3, 'enabled': 1.

A list of module-specific information associated with a particular ol41nnHETP module.

A module entry containing objects that describe the module level for that particular module.

The slot number of this module.

The serial number of this module, as entered by the user through the Management interface.

A table of port-specific information for each port of this module type.

A port entry containing objects that describe this port.

The slot (stack) number of this port's module.

The port number of this port.

Used to reset the port's '802.3 state machine', which will re-enable a disabled port and/or reconnect a partitioned port. Enumeration: 'ready': 1, 'reset': 2.

The port's (good) link integrity configuration. Enabling link integrity configures the port to conform to the link integrity feature as specified by 10BASE-T. Enumeration: 'disabled': 2, 'enabled': 1.

A list of module-specific information associated with a particular 52nnM-EC module in the concentrator.

A description of the 52nnM-EC module attributes.

The slot number of this module.

The version number of the software.

A 43 octet indication of the current applicable IBM 3174 System Status Code. For more information consult the 52nnM-EC reference manual.

The ring's bandwidth in Mega-bits per second. Enumeration: 'sixteenMegabit': 2, 'fourMegabit': 1.

The status of the ring containing this module. Enumeration: 'okay': 1, 'beaconing': 3, 'closed': 2.

The IP Address of this module.

A 6 octet address that uniquely identifies the MAC address of this module.

A table of port-specific information for each port of this module type.

A description of this module's port attributes.

The slot number of this port's module.

The port number of this port.

A list of trunk-specific information about each trunk for this module type.

A description of 52nnM-EC trunk attributes.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.

The trunk number for this trunk.

A list of module attributes that apply to this model. To access an ol53nnMTDDIModTable entry, the ol53nnMTDDIModSlotIndex attribute is used.

A list of module-specific information about a specific 53nnM-TDDI module in the concentrator.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olModSlotIndex.

Down stream slot (transmit to)

Down stream slot (receive from)

transmit DBA (debug only) Enumeration: 'fddi-path-1': 24, 'fddi-path-3': 26, 'fddi-path-2': 25, 'fddi-path-5': 28, 'fddi-path-4': 27, 'fddi-path-7': 30, 'fddi-path-6': 29, 'fddi-path-8': 31, 'isolated': 2.

receive DBA (debug only) Enumeration: 'fddi-path-1': 24, 'fddi-path-3': 26, 'fddi-path-2': 25, 'fddi-path-5': 28, 'fddi-path-4': 27, 'fddi-path-7': 30, 'fddi-path-6': 29, 'fddi-path-8': 31, 'isolated': 2.

An array which is indexed by DBA number. Each element contains the slot number (1..16) which is assigned to transmit on this DBA. (debug only)

A table of port-specific information for each port of this module type.

A list of module-specific information about a specific 53nnM-TDDI port in the concentrator.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortSlotIndex.

A unique value that identifies a particular port within this module. Its value ranges between 1 and olModPortNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olPortIndex.

Specifies the FDDI port type. If the port is on an FFM, the only allowed values are slave(3) and master(4). In addition, there can only be one active slave port on any concentrator FDDI network. Enumeration: 'master': 4, 'slave': 3.

(refer to ANSI SMT 9.6.2). Enumeration: 'pc8': 9, 'pc9': 10, 'pc2': 3, 'pc3': 4, 'pc0': 1, 'pc1': 2, 'pc6': 7, 'pc7': 8, 'pc4': 5, 'pc5': 6.

An indication of the connect state of this PORT. Basically, this gives a higher level view of the state of the connection by grouping PCM states and the PC-Withhold flag state. The supported values and their corresponding PCM states and PC-Withhold condition, when relevant, are: disabled: (PC0:Off, PC9:Maint) connecting: (PC1(Break) || PC3 (Connect) || PC4(next) || PC5 (Signal) || PC6(Join) || PC7 (Verify)) && (PC-Withhold = None) standby: (PC-Withhold != None) active: (PC2:Trace || PC8:Active) Enumeration: 'disabled': 1, 'standby': 3, 'connecting': 2, 'active': 4.

The type (PC-Neighbor) of the remote PORT that is determined in PC-Signaling in R-Val (1,2) (refer to ANSI SMT 9.6.3.2). Enumeration: 'a': 1, 'master': 4, 'b': 2, 'slave': 3, 'unknown': 5.

The indication, in PC-Signaling that the remote partner intends to place a MAC in the output token PATH of this PORT. Signaled as R-Val (9) (refer to ANSI SMT 9.6.3.2). Enumeration: 'false': 2, 'true': 1.

The Break State, BS-Flag (refer to ANSI SMT 9.4.3.4). Enumeration: 'false': 2, 'true': 1.

PC-Withhold, (refer to ANSI SMT 9.4.1). Enumeration: 'm-m': 2, 'none': 1, 'other': 3.

This variable is set to true whenever LerEstimate is less than or equal to LerAlarm (the larger the number the smaller the value). Enumeration: 'bad': 1, 'okay': 2.

FDDI module specific trunk table variables. At present there are none.

A description of 53nnM-TDDI trunk attributes.

A unique value that identifies a particular module. Its value ranges between 1 and olModSlotNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkSlotIndex.

A unique value that identifies a particular trunk within this module. Its value ranges between 1 and olModTrunkNumber. The module identified by a particular value of this index is the same module as indentified by the same value of olTrunkIndex.

A table of condensed module information.