CAMBIUM-PTP670-MIB: View SNMP OID List / Download MIB

MIB for non-line-of-sight (NLOS) wireless ethernet bridge.

Number of entries in the dfsTable

A table storing a snapshot of various DFS measurements for each channel

Table DfsTable

used to index values in the dfsTable.

Snapshot of DFS means

Snapshot of DFS 99.9 percentiles

Snapshot of DFS peaks

Enables Extended Spectrum Scanning Enumeration: 'disabled': 0, 'enabled': 1.

When Local Packet Filtering is Enabled, the unit keeps track of the port (Main, SFP, Aux or Wireless) on which a packet with a given MAC source address destined to the management agent has been received. This MAC address to port mapping is then used in order to route any response from the management agent to the right port. When Local Packet Filtering is Disabled, any Ethernet packet from the management agent is sent to all ports. Enumeration: 'disabled': 0, 'enabled': 1.

Total number of good packets the bridge has transmitted to the internal TCP/IP stack.

Total number of good packets the bridge has received from the internal TCP/IP stack.

Internet protocol (IPv4) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network.

A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance.

The IPv4 address of a device on the current network that acts as an IPv4 network gateway. A gateway acts as an entrance / exit to packets from / to other networks

MAC address of the unit forming the other end of the link

The wireless link operates using a master and slave relationship Enumeration: 'slave': 1, 'master': 0.

Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link. This may be reduced during installation

Antenna Gain. Expressed in 10ths of dBi.

Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna.

Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm

This control sets the bandwidth of the transmit and receive radio channels Enumeration: 'bw30MHz': 0, 'bw15MHz': 1, 'bw5MHz': 3, 'bw50MHz': 6, 'bw20MHz': 4, 'bw45MHz': 8, 'bw10MHz': 2, 'bw40MHz': 7, 'bw56MHz': 5.

Name of the link allocated by the System Administrator. Used to establish a connection with the correct wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the link.

This field contains a user-provided description of the site name together with any additional notes

ODUs must be configured in pairs before a link can be established. The Access Method attribute determines how the paired ODUs will recognise each other. For the Link Access method, each ODU must be configured with Target MAC Address equal to the MAC Address of the other unit. For the Link Name Access method, both units must be configured with the same Link Name. For the Group Access method, both units must be configured with the same Group ID. Enumeration: 'groupAccess': 2, 'linkAccess': 0, 'linkNameAccess': 1.

When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group

Internet protocol (IPv6) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network.

IP protocol selection. Choice of IPv4, IPv6 or Dual. Enumeration: 'dualIPv4andIPv6': 2, 'iPv4': 0, 'iPv6': 1.

The auto configured link local IPv6 address

IPv6 prefix length

The IPv6 address of a device on the current network that is currently acting as an IPv6 network gateway. A gateway acts as an entrance / exit to packets from / to other networks.

The type of Internet address specified by the associated remoteInternetAddressType. Enumeration: 'dns': 16, 'ipv6z': 4, 'unknown10': 9, 'unknown': 0, 'unknown12': 11, 'unknown13': 12, 'ipv4z': 3, 'unknown15': 14, 'unknown16': 15, 'unknown14': 13, 'unknown6': 5, 'ipv4': 1, 'unknown11': 10, 'ipv6': 2, 'unknown8': 7, 'unknown9': 8, 'unknown7': 6.

INET address used to identify the peer wireless unit

Lowest center frequency of the subset of channels.

Highest center frequency of the subset of channels.

Control for enabling/disabling the radio transmitter of the Master. Note: Use Web Properties to control this feature. Enumeration: 'muted': 1, 'enabled': 0.

Antenna Selection. Choice of Integrated or Connectorized Enumeration: 'connectorized': 1, 'integrated': 0.

To select transmitter channel(s) (H,V) Enumeration: 'vOnly': 2, 'handV': 0, 'hOnly': 1.

This attribute determines whether the device operates as part of a PTP or an HCMP network topology. Enumeration: 'pointToPoint': 0, 'highCapacityMultiPoint': 1.

Number of entries in the ConfigurationInstancedTable.

Instanced Public stats table.

Table ConfigurationInstancedTable

Used to index the ConfigurationInstancedTable.

The type of Internet address specified by the associated remoteInternetAddressType. Enumeration: 'dns': 16, 'ipv6z': 4, 'unknown10': 9, 'unknown': 0, 'unknown12': 11, 'unknown13': 12, 'ipv4z': 3, 'unknown15': 14, 'unknown16': 15, 'unknown14': 13, 'unknown6': 5, 'ipv4': 1, 'unknown11': 10, 'ipv6': 2, 'unknown8': 7, 'unknown9': 8, 'unknown7': 6.

INET address used to identify the peer wireless unit

This field contains user-provided name of the peer received over the wireless link

This field contains user-provided name for this unit

Authorization Method to be used - Whitelist or Blacklist Enumeration: 'blacklist': 1, 'whitelist': 0.

This field contains user-provided name of the peer received over the wireless link

This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot. Enumeration: 'disabled': 0, 'enabled': 1.

This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for! Bits: 'neg10MbpsHalfDuplex': 3, 'neg100MbpsHalfDuplex': 5, 'neg1000MbpsFullDuplex': 7, 'neg10MbpsFullDuplex': 4, 'neg100MbpsFullDuplex': 6, 'negInvalid': 2.

This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot Enumeration: 'disabled': 0, 'enabled': 1.

Current status of the Main PSU Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'down': 0, 'copperLinkUp': 1, 'fiberLinkUp': 2.

The current speed and duplex of the Main PSU Ethernet link Enumeration: 'speedUnknown6': 5, 'speed1000MbpsFullDuplex': 0, 'speed100MbpsFullDuplex': 1, 'speed10MbpsFullDuplex': 3, 'speed100MbpsHalfDuplex': 2, 'speed10MbpsHalfDuplex': 4.

When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem. Enumeration: 'disabled': 0, 'enabled': 1.

This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot Enumeration: 'iEEE8021adTaggedSTagorBTagType88a8': 2, 'noVLANTagging': 0, 'iEEE8021QTaggedCTagType8100': 1.

This VLAN Priority (0-7) will be included in packets generated by the management interfaces Enumeration: 'p2': 2, 'p3': 3, 'p0': 0, 'p1': 1, 'p6': 6, 'p7': 7, 'p4': 4, 'p5': 5.

This VLAN VID (0-4094) will be included in packets generated by the management interfaces. Note the new setting will only take effect after a system reboot

Current status of the Aux Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'down': 0, 'copperLinkUp': 1.

The current speed and duplex of the Aux Ethernet link Enumeration: 'speedUnknown6': 5, 'speed1000MbpsFullDuplex': 0, 'speed100MbpsFullDuplex': 1, 'speed10MbpsFullDuplex': 3, 'speed100MbpsHalfDuplex': 2, 'speed10MbpsHalfDuplex': 4.

Number of entries in the vLANPriorityTable.

A priority queue mapping table. This is a list of packet queues indexed by Ethernet priority.

Table EthernetPriorityTable

Ethernet priority flag, used to index values in the ethernetPriorityTable Enumeration: 'p2': 3, 'p3': 4, 'p0': 1, 'p1': 2, 'p6': 7, 'p7': 8, 'p4': 5, 'p5': 6, 'untagged': 9.

Configures the classification of this Ethernet priority (also known as IEEE 802.1p value) to an egress queue at the wireless port Enumeration: 'q1': 1, 'q0': 0, 'q3': 3, 'q2': 2, 'q5': 5, 'q4': 4, 'q7': 7, 'q6': 6.

Number of entries in the l2CPPriorityTable.

A priority queue mapping table. This is a list of packet queues indexed by L2CP priority.

Table L2CPPriorityTable

L2CP priority flag, used to index values in the l2CPPriorityTable Enumeration: 'bridge': 1, 'cFM': 3, 'rAPS': 4, 'mRP': 2, 'pPPoEDiscoveryLCP': 6, 'eAPS': 5.

Configures the classification of this layer two control protocol (L2CP) to an egress queue at the wireless port Enumeration: 'q1': 1, 'q0': 0, 'q3': 3, 'q2': 2, 'q5': 5, 'q4': 4, 'q7': 7, 'q6': 6.

Number of entries in the iPDSCPPriorityTable.

A priority queue mapping table. This is a list of packet queues indexed by L3 IP DSCP priority.

Table IPDSCPPriorityTable

IP DSCP priority flag, used to index values in the iPDSCPPriorityTable

Configures the classification of this IP differentiated services code point (DSCP) value to an egress queue at the wireless port Enumeration: 'q1': 1, 'q0': 0, 'q3': 3, 'q2': 2, 'q5': 5, 'q4': 4, 'q7': 7, 'q6': 6.

Number of entries in the mPLSTCPriorityTable.

A priority queue mapping table. This is a list of priority queues indexed by MPLS TC priority.

Table MPLSTCPriorityTable

MPLS TC priority flag, used to index values in the mPLSTCPriorityTable

Configures the classification of this MPLS traffic class (the field formerly known as EXP) to an egress queue at the wireless port Enumeration: 'q1': 1, 'q0': 0, 'q3': 3, 'q2': 2, 'q5': 5, 'q4': 4, 'q7': 7, 'q6': 6.

When enabled, this causes the management link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem. Enumeration: 'disabled': 0, 'enabled': 1.

Selects classification based on fields in the Ethernet header (Layer 2) or in the Network header (Layer 3). The unit recognises two network layer protocols: IP and MPLS Enumeration: 'ethernet': 0, 'iPMPLS': 1.

Configures the classification of unknown network protocols to an egress queue at the wireless port. Unknown means something other than IP and MPLS Enumeration: 'q1': 1, 'q0': 0, 'q3': 3, 'q2': 2, 'q5': 5, 'q4': 4, 'q7': 7, 'q6': 6.

This Differentiated Services Code Point value will be inserted in the IP Header of all IP Datagrams transmitted by the management interfaces

Current status of Ethernet Data traffic bridging over the wireless link Enumeration: 'disabled': 0, 'enabled': 1.

Indicates the service or services supported by the Main PSU Ethernet port Enumeration: 'disabled': 0, 'dataandInBandManagement': 2, 'outofBandLocalManagement': 3, 'outofBandRemoteManagement': 4, 'dataOnly': 1.

Indicates the service or services supported by the Aux Ethernet port Enumeration: 'disabled': 0, 'dataandInBandManagement': 2, 'outofBandLocalManagement': 3, 'outofBandRemoteManagement': 4, 'dataOnly': 1.

Indicates the service or services supported by the SFP Ethernet port Enumeration: 'disabled': 0, 'dataandInBandManagement': 2, 'outofBandLocalManagement': 3, 'outofBandRemoteManagement': 4, 'dataOnly': 1.

Controls whether the bridge tunnels or discards Layer 2 PAUSE frames arriving at the Data Port. Such frames are identified by the destination MAC Address being equal to 01-80-C2-00-00-01 Enumeration: 'tunnel': 0, 'discard': 1.

This controls whether the local SFP Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot. Enumeration: 'disabled': 0, 'enabled': 1.

This sets the different SFP Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for! Bits: 'neg10MbpsHalfDuplex': 3, 'neg100MbpsHalfDuplex': 5, 'neg1000MbpsFullDuplex': 7, 'neg10MbpsFullDuplex': 4, 'neg100MbpsFullDuplex': 6, 'negInvalid': 2.

This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot Enumeration: 'disabled': 0, 'enabled': 1.

Current status of the SFP Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'down': 0, 'copperLinkUp': 1, 'fiberLinkUp': 2.

The current speed and duplex of the SFP Ethernet link Enumeration: 'speedUnknown6': 5, 'speed1000MbpsFullDuplex': 0, 'speed100MbpsFullDuplex': 1, 'speed10MbpsFullDuplex': 3, 'speed100MbpsHalfDuplex': 2, 'speed10MbpsHalfDuplex': 4.

The state of the Power Over Ethernet (PoE) output of the Aux port. Enabling PoE output may lead to system instability; please refer to the User Guide before enabling this control Enumeration: 'disabled': 0, 'enabled': 1.

Current status of the Power Over Ethernet (PoE) output of the Aux port Enumeration: 'poEOutputOverloadError': 3, 'poEOutputOverTempError': 4, 'poEOutputOn': 0, 'poEOutputDisabled': 1, 'poEOutputEnabledbutNotActiveErrororNoLoadPresent': 2, 'poEOutputErrorDetected': 5.

Controls whether Synchronous Ethernet (SyncE) network synchronization is enabled. Enumeration: 'disabled': 0, 'internalTDMUseOnly': 2, 'enabled': 1.

EEC-Option 1 applies to synchronous Ethernet equipments that are designed to interwork with networks optimized for the 2048-kbit/s hierarchy. Corresponds to ITU-T G.813 Option 1; EEC-Option 2 applies to synchronous Ethernet equipments that are designed to interwork with networks optimized for the 1544-kbit/s hierarchy. Corresponds to Type IV clock from ITU-T G.812. Enumeration: 'eECOption1': 0, 'eECOption2': 1.

Override for the Synchronous Ethernet (SyncE) received Quality Level (QL) on the main PSU port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'disabled': 0, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the Main PSU port Enumeration: 'disabled': 0, 'enabled': 1.

Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the SFP port Enumeration: 'disabled': 0, 'enabled': 1.

Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the Aux port Enumeration: 'disabled': 0, 'enabled': 1.

The current state of Synchronous Ethernet (SyncE) network synchronization. Enumeration: 'acquiringWirelessLock': 1, 'lockedLocalHoldoverAcquired': 4, 'lockedRemoteHoldoverAcquired': 7, 'disabled': 0, 'freeRunning': 2, 'holdover': 5, 'lockedLocalAcquiringHoldover': 3, 'lockedRemoteAcquiringHoldover': 6.

The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the main PSU port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'none': 0, 'qLFAILED': 13, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the auxiliary port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'none': 0, 'qLFAILED': 13, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the SFP port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'none': 0, 'qLFAILED': 13, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the main PSU port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'none': 0, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the auxiliary port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'none': 0, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the SFP port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'none': 0, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

The main PSU port Synchronous Ethernet (SyncE) Master/Slave status Enumeration: 'slave': 1, 'master': 0.

The auxiliary port Synchronous Ethernet (SyncE) Master/Slave status Enumeration: 'slave': 1, 'master': 0.

The SFP port Synchronous Ethernet (SyncE) Master/Slave status Enumeration: 'slave': 1, 'master': 0.

The main PSU port Gigabit Ethernet Master/Slave status Enumeration: 'slave': 1, 'master': 0, 'notApplicable': 2.

The auxiliary port Gigabit Ethernet Master/Slave status Enumeration: 'slave': 1, 'master': 0, 'notApplicable': 2.

The SFP port Gigabit Ethernet Master/Slave status Enumeration: 'slave': 1, 'master': 0, 'notApplicable': 2.

This control enables the Precision Time Protocol (IEEE-1588) Transparent Clock. Once enabled the unit will modify the correction field in PTP event messages to take account of the time these frames have been resident in this system. This will happen for all PTP frames at Layer 2 & Layer 3 (IPv4 & IPv6) unless a transparent clock VLAN is enabled. Enumeration: 'disabled': 0, 'enabled': 1.

If All is selected then all PTP frames will have their correction fields modified with the residence time. If an S-TAG or C-TAG is selected, only frames with this VLAN tag and matching the VLAN ID in the Transparent Clock VID will have their correction fields modified. Enumeration: 'cTagged': 2, 'all': 0, 'sTagged': 1.

The VLAN ID which frames must match if they are to be corrected. Only valid when an S-TAG or C-TAG has been selected.

The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the main PSU port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'none': 0, 'qLFAILED': 13, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the auxiliary port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'none': 0, 'qLFAILED': 13, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the SFP port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'none': 0, 'qLFAILED': 13, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

The Synchronous Ethernet (SyncE) Receive Status of the main PSU port Enumeration: 'failed': 2, 'good': 0, 'waittoRestore': 1.

The Synchronous Ethernet (SyncE) Receive Status of the auxiliary port Enumeration: 'failed': 2, 'good': 0, 'waittoRestore': 1.

The Synchronous Ethernet (SyncE) Receive Status of the SFP port Enumeration: 'failed': 2, 'good': 0, 'waittoRestore': 1.

Current status of the NIDU LAN Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'down': 0, 'copperLinkUp': 1, 'fiberLinkUp': 2.

The current speed and duplex of the Ethernet link to the NIDU LAN Port Enumeration: 'speedUnknown6': 5, 'speed1000MbpsFullDuplex': 0, 'speed100MbpsFullDuplex': 1, 'speed10MbpsFullDuplex': 3, 'speed100MbpsHalfDuplex': 2, 'speed10MbpsHalfDuplex': 4.

Configures the classification of traffic to an egress queue at the wireless port Enumeration: 'q1': 1, 'q0': 0, 'q3': 3, 'q2': 2, 'q5': 5, 'q4': 4, 'q7': 7, 'q6': 6.

This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot. Enumeration: 'disabled': 0, 'enabled': 1.

This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for! Bits: 'neg10MbpsHalfDuplex': 3, 'neg100MbpsHalfDuplex': 5, 'neg1000MbpsFullDuplex': 7, 'neg10MbpsFullDuplex': 4, 'neg100MbpsFullDuplex': 6, 'negInvalid': 2.

This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot Enumeration: 'disabled': 0, 'enabled': 1.

The NIDU LAN port Gigabit Ethernet Master/Slave status Enumeration: 'slave': 1, 'master': 0, 'notApplicable': 2.

Number of MAB frames transmitted

When enabled the local Out-of-Band interface can be used to access the remote management network. If not enabled the local management agent can still be accessed from the remote management network and the local Out-of-Band interface Enumeration: 'yes': 1, 'no': 0.

IEEE 1588 Transparent Clock source Enumeration: 'auxplusSFP': 5, 'mainPSUplusAuxplusSFP': 6, 'mainPSUplusSFP': 4, 'mainPSUplusAux': 3, 'sFP': 2, 'mainPSU': 0, 'aux': 1.

Select a Sync E Slave Port Enumeration: 'sFPPort': 1, 'mainPSUPort': 0.

Override for the Synchronous Ethernet (SyncE) received Quality Level (QL) on the SFP Port. Enumeration: 'qLEEC2QLST3': 8, 'qLPROV': 11, 'qLPRS': 1, 'qLSTU': 2, 'qLST2': 4, 'disabled': 0, 'qLSSUAQLTNC': 5, 'qLSMC': 10, 'qLDNUQLDUS': 12, 'qLST3E': 7, 'qLPRC': 3, 'qLEEC1QLSEC': 9, 'qLSSUB': 6.

Number of entries in the ethernetInstancedTable.

Instanced table showing the ethernet status

Table EthernetInstancedTable

Used to index the ethernetInstancedTable.

Current status of Ethernet Data traffic bridging over the wireless link Enumeration: 'disabled': 0, 'enabled': 1.

Number of entries in the ethernetStatisticsTable.

Instanced table showing the ethernet statistics

Table EthernetStatisticsTable

Used to index the ethernetStatisticsTable.

This object identifies the ethernet interface that this ethernetStatistics entry is configured to report. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1.

Total number of octets (excluding framing bits but including FCS octets) received from the LAN in good packets

Total number of packets (including bad packets, broadcast packets, and multicast packets) received

Number of good and bad broadcast packets received from the LAN. Note that this does not include multicast packets.

Number of frames received with errors. The errors can be a frame check sequence (CRC) error, an alignment error or an incorrect frame length

Number of short frames (<64 Bytes) received from the LAN with or without a valid CRC

Number of oversize frames received from the LAN with or without a valid CRC

Total number of octets transmitted to the LAN

Total number of frames transmitted to the LAN

Number of broadcast frames transmitted to the LAN. Note that this does not include multicast packets.

The line interface type. If this is set to 'None' then the TDM interfaces are disabled, and the TDM settings will be ignored. Enumeration: 'none': 0, 'e1': 1, 't1': 2.

@Current status of the connection to the TDM Box. A state of 'Up' on a green background indicates that the TDM Box is connected OK. When connecting a TDM Box only the Main Ethernet port should be used Enumeration: 'codeDownloadInProgress': 5, 'ok': 0, 'nIDUdetectedonAUXport': 3, 'error': 4, 'notConnected': 2, 'connectedNotConfigured': 1.

The number of TDM channels enabled in the system

Number of entries in the TdmTable

A table storing a configuration and status for each TDM channel

Table TdmTable

TDM Channel flag, used to index channels in the TdmTable

Current status of the TDM channels. A value of 0 indicates that a TDM channel is established Enumeration: 'remoteTiming': 4, 'noSignalRemote': 2, 'up': 0, 'disabled': 6, 'noSignalLocalandRemote': 3, 'noSignalLocalandRemoteTiming': 5, 'noSignalLocal': 1.

The line code setting of the TDM interfaces. This must match the setting of the device connected to an interface Enumeration: 'aMI': 0, 'b8ZSorHDB3': 1.

The lengths of the cables connected to the TDM interfaces, measured in feet Enumeration: 'feet133': 0, 'feet399': 2, 'feet655': 4, 'feet533': 3, 'feet266': 1.

The loopback status of TDM channels. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'wireless': 2, 'copper': 1, 'none': 0.

Current status of the configuration of the TDM Box. A state of 'Ok' on a green background indicates that the TDM Box configuration is matched OK with the remote end. Enumeration: 'enabledchannelsmismatch': 2, 'linetypemismatch': 1, 'ok': 0, 'linetypeandenabledchannelsmismatch': 3.

The lowest modulation mode at which tdm data will be sent. The effective lowest modulation mode is displayed in the TDM Configuration page Enumeration: 'modTransient9': 21, 'modTransient8': 19, 'modTransient7': 17, 'modTransient6': 13, 'modTransient5': 11, 'modTransient4': 9, 'modTransient3': 7, 'modTransient2': 5, 'modTransient1': 3, 'mod256qam81percentDual': 24, 'mod64qam75percentSingle': 10, 'mod64qam92percentSingle': 12, 'mod16qam63percentSingleA': 6, 'mod16qam63percentSingleB': 15, 'mod16qam87percentSingle': 8, 'mod64qam92percentDual': 22, 'modBpsk63percent': 1, 'modQpsk63percentSingle': 2, 'mod16qam63percentDual': 16, 'modTransient10': 23, 'mod16qam87percentDual': 18, 'modQpsk87percentSingle': 4, 'mod256qam81percentSingle': 14, 'modAcquisition': 0, 'mod64qam75percentDual': 20.

The Regulatory Band prohibits the wireless unit from operating outside the regulated limits. An invalid Regulatory Band may be caused by a missing or incorrect License Key, a corrupt MAC Address or an attempt to configure a Regulatory Band not allowed by the License Key or an execution of Reset Configuration. NB: a change of state may generate an SNMP trap and/or SMTP email alert. Enumeration: 'reg4054GHz': 40, 'reg258GHz': 2, 'reg107': 107, 'reg106': 106, 'reg1659GHz': 16, 'reg218': 218, 'reg103': 103, 'reg102': 102, 'reg215': 215, 'reg214': 214, 'reg217': 217, 'reg216': 216, 'reg109': 109, 'reg108': 108, 'reg213': 213, 'reg212': 212, 'reg5458GHz': 54, 'reg754GHz': 7, 'reg558GHz': 5, 'reg219': 219, 'reg658GHz': 6, 'reg165': 165, 'reg9545GHz': 95, 'reg175': 175, 'reg223': 223, 'reg177': 177, 'reg6058GHz': 60, 'reg199': 199, 'reg156': 156, 'reg197': 197, 'reg194': 194, 'reg195': 195, 'reg192': 192, 'reg143': 143, 'reg190': 190, 'reg191': 191, 'reg5754GHz': 57, 'reg131': 131, 'reg132': 132, 'reg133': 133, 'reg134': 134, 'reg135': 135, 'reg136': 136, 'reg137': 137, 'reg138': 138, 'reg139': 139, 'reg222': 222, 'reg173': 173, 'reg224': 224, 'reg225': 225, 'reg226': 226, 'reg210': 210, 'reg4254GHz': 42, 'reg9449GHz': 94, 'reg146': 146, 'reg4354GHz': 43, 'reg6149GHz': 61, 'regInvalid': 0, 'reg3249GHzLicensed': 32, 'reg854GHz': 8, 'reg8247GHz': 82, 'reg4458GHz': 44, 'reg6352GHz': 63, 'reg189': 189, 'reg188': 188, 'reg185': 185, 'reg184': 184, 'reg187': 187, 'reg186': 186, 'reg181': 181, 'reg8652GHz54GHz': 86, 'reg183': 183, 'reg182': 182, 'reg3558GHz': 35, 'reg358GHz': 3, 'reg129': 129, 'reg128': 128, 'reg3951GHzETSIBroadbandDisasterRelief': 39, 'reg126': 126, 'reg125': 125, 'reg8147GHz': 81, 'reg123': 123, 'reg1849GHzPublicSafety': 18, 'reg121': 121, 'reg120': 120, 'reg6952GHz': 69, 'reg10158GHz': 101, 'reg4154GHz': 41, 'reg221': 221, 'reg110': 110, 'reg3349GHzETSIBroadbandDisasterRelief': 33, 'reg209': 209, 'reg23': 23, 'reg5358GHz': 53, 'reg7252GHz': 72, 'reg3158GHz': 31, 'reg9648GHz': 96, 'reg2758GHz': 27, 'reg158': 158, 'reg255': 255, 'reg150': 150, 'reg211': 211, 'reg6651GHz': 66, 'reg6251GHz52GHz': 62, 'reg159': 159, 'reg7652GHz': 76, 'reg152': 152, 'reg153': 153, 'reg113': 113, 'reg151': 151, 'reg6852GHz': 68, 'reg157': 157, 'reg7552GHz': 75, 'reg155': 155, 'reg122': 122, 'reg154': 154, 'reg196': 196, 'reg201': 201, 'reg250': 250, 'reg2654GHz': 26, 'reg6752GHz': 67, 'reg1449GHzPublicSafety': 14, 'reg4558GHz': 45, 'reg228': 228, 'reg4658GHz': 46, 'reg180': 180, 'reg237': 237, 'reg236': 236, 'reg208': 208, 'reg234': 234, 'reg233': 233, 'reg232': 232, 'reg231': 231, 'reg230': 230, 'reg1354GHz': 13, 'reg9349GHz': 93, 'reg239': 239, 'reg238': 238, 'reg149': 149, 'reg148': 148, 'reg141': 141, 'reg140': 140, 'reg2858GHz': 28, 'reg142': 142, 'reg145': 145, 'reg144': 144, 'reg147': 147, 'reg2154GHz': 21, 'reg5558GHz': 55, 'reg7152GHz': 71, 'reg252': 252, 'reg7452GHz': 74, 'reg5258GHz': 52, 'reg5058GHz': 50, 'reg5158GHz': 51, 'reg242': 242, 'reg127': 127, 'reg9152GHzParabolicantenna': 91, 'reg241': 241, 'reg246': 246, 'reg247': 247, 'reg6551GHz': 65, 'reg245': 245, 'reg8758GHz': 87, 'reg248': 248, 'reg249': 249, 'reg2558GHz': 25, 'reg2458GHz': 24, 'reg124': 124, 'reg7352GHz': 73, 'reg198': 198, 'reg158GHz': 1, 'reg244': 244, 'reg243': 243, 'reg6451GHz': 64, 'reg15': 15, 'reg8352GHz': 83, 'reg254': 254, 'reg8451GHz': 84, 'reg1958GHz': 19, 'reg4958GHz': 49, 'reg200': 200, 'reg240': 240, 'reg193': 193, 'reg251': 251, 'reg3654GHz': 36, 'reg253': 253, 'reg8551GHz52GHz': 85, 'reg2258GHz': 22, 'reg3852GHz': 38, 'reg1254GHz': 12, 'reg7752GHz': 77, 'reg1158GHz': 11, 'reg3758GHz': 37, 'reg9949GHz29dBiantenna': 99, 'reg130': 130, 'reg229': 229, 'reg9251GHzParabolicantenna': 92, 'reg8049GHz': 80, 'reg7849GHz': 78, 'reg9752GHz': 97, 'reg2054GHz': 20, 'reg8949GHz': 89, 'reg235': 235, 'reg3054GHz': 30, 'reg174': 174, 'reg7052GHz': 70, 'reg176': 176, 'reg160': 160, 'reg170': 170, 'reg171': 171, 'reg172': 172, 'reg10458GHzNoRTTT': 104, 'reg178': 178, 'reg179': 179, 'reg166': 166, 'reg116': 116, 'reg117': 117, 'reg114': 114, 'reg115': 115, 'reg112': 112, 'reg458GHzWithRTTT': 4, 'reg105': 105, 'reg111': 111, 'reg206': 206, 'reg207': 207, 'reg204': 204, 'reg164': 164, 'reg202': 202, 'reg203': 203, 'reg118': 118, 'reg119': 119, 'reg7954GHz': 79, 'reg220': 220, 'reg1058GHz': 10, 'reg227': 227, 'reg5654GHz': 56, 'reg205': 205, 'reg1759GHz': 17, 'reg954GHz': 9, 'reg8849GHz': 88, 'reg2958GHz': 29, 'reg10048GHz': 100, 'reg4858GHz': 48, 'reg4758GHz': 47, 'reg163': 163, 'reg162': 162, 'reg161': 161, 'reg9054GHzParabolicantenna': 90, 'reg167': 167, 'reg5858GHz': 58, 'reg5958GHz': 59, 'reg3458GHz': 34, 'reg169': 169, 'reg168': 168, 'reg9849GHz27dBiantenna': 98.

The product variant Enumeration: 'pTP50670ATEX': 19, 'pTPxx500': 10, 'pTPxx700': 17, 'pTPxx400Deprecated1': 1, 'spare1': 4, 'spare3': 7, 'spare2': 6, 'pTPxx400Deprecated2': 2, 'pTPxx600Full': 12, 'pTPxx600Lite': 11, 'pTPxx400Full': 0, 'pMPMedusa': 16, 'pTPxx400Lite': 3, 'pMP455': 14, 'pTPxx500FullDeprecated': 8, 'pTP50670': 18, 'pTPxx300': 5, 'pTPxx500LiteDeprecated': 9, 'pTP800': 15, 'pTPxx650': 13, 'pTP48670': 20.

Name of the product variant

The hardware frequency variant Enumeration: 'freq45XXX': 1, 'freq50XXX': 0, 'freq48XXX': 2.

SNMPv3 availability control Enumeration: 'disabled': 0, 'enabled': 1.

The license key version.

The unit serial number.

The license key issue number for this unit.

The country in which this unit is licensed to operate.

The number of regulatory bands for which the unit is licensed to operate.

Table LicenseRegulatoryBandsTable

License regulatory bands, used to index the LicenseRegulatoryBandsTable.

The list of regulatory bands for which the unit is licensed to operate. A regulatory band prohibits the wireless unit from operating outside the regulated limits. An invalid regulatory band indicates a corrupted license key. NB: a change of state may generate an SNMP trap and/or SMTP email alert. Enumeration: 'reg4054GHz': 40, 'reg258GHz': 2, 'reg107': 107, 'reg106': 106, 'reg1659GHz': 16, 'reg218': 218, 'reg103': 103, 'reg102': 102, 'reg215': 215, 'reg214': 214, 'reg217': 217, 'reg216': 216, 'reg109': 109, 'reg108': 108, 'reg213': 213, 'reg212': 212, 'reg5458GHz': 54, 'reg754GHz': 7, 'reg558GHz': 5, 'reg219': 219, 'reg658GHz': 6, 'reg165': 165, 'reg9545GHz': 95, 'reg175': 175, 'reg223': 223, 'reg177': 177, 'reg6058GHz': 60, 'reg199': 199, 'reg156': 156, 'reg197': 197, 'reg194': 194, 'reg195': 195, 'reg192': 192, 'reg143': 143, 'reg190': 190, 'reg191': 191, 'reg5754GHz': 57, 'reg131': 131, 'reg132': 132, 'reg133': 133, 'reg134': 134, 'reg135': 135, 'reg136': 136, 'reg137': 137, 'reg138': 138, 'reg139': 139, 'reg222': 222, 'reg173': 173, 'reg224': 224, 'reg225': 225, 'reg226': 226, 'reg210': 210, 'reg4254GHz': 42, 'reg9449GHz': 94, 'reg146': 146, 'reg4354GHz': 43, 'reg6149GHz': 61, 'regInvalid': 0, 'reg3249GHzLicensed': 32, 'reg854GHz': 8, 'reg8247GHz': 82, 'reg4458GHz': 44, 'reg6352GHz': 63, 'reg189': 189, 'reg188': 188, 'reg185': 185, 'reg184': 184, 'reg187': 187, 'reg186': 186, 'reg181': 181, 'reg8652GHz54GHz': 86, 'reg183': 183, 'reg182': 182, 'reg3558GHz': 35, 'reg358GHz': 3, 'reg129': 129, 'reg128': 128, 'reg3951GHzETSIBroadbandDisasterRelief': 39, 'reg126': 126, 'reg125': 125, 'reg8147GHz': 81, 'reg123': 123, 'reg1849GHzPublicSafety': 18, 'reg121': 121, 'reg120': 120, 'reg6952GHz': 69, 'reg10158GHz': 101, 'reg4154GHz': 41, 'reg221': 221, 'reg110': 110, 'reg3349GHzETSIBroadbandDisasterRelief': 33, 'reg209': 209, 'reg23': 23, 'reg5358GHz': 53, 'reg7252GHz': 72, 'reg3158GHz': 31, 'reg9648GHz': 96, 'reg2758GHz': 27, 'reg158': 158, 'reg255': 255, 'reg150': 150, 'reg211': 211, 'reg6651GHz': 66, 'reg6251GHz52GHz': 62, 'reg159': 159, 'reg7652GHz': 76, 'reg152': 152, 'reg153': 153, 'reg113': 113, 'reg151': 151, 'reg6852GHz': 68, 'reg157': 157, 'reg7552GHz': 75, 'reg155': 155, 'reg122': 122, 'reg154': 154, 'reg196': 196, 'reg201': 201, 'reg250': 250, 'reg2654GHz': 26, 'reg6752GHz': 67, 'reg1449GHzPublicSafety': 14, 'reg4558GHz': 45, 'reg228': 228, 'reg4658GHz': 46, 'reg180': 180, 'reg237': 237, 'reg236': 236, 'reg208': 208, 'reg234': 234, 'reg233': 233, 'reg232': 232, 'reg231': 231, 'reg230': 230, 'reg1354GHz': 13, 'reg9349GHz': 93, 'reg239': 239, 'reg238': 238, 'reg149': 149, 'reg148': 148, 'reg141': 141, 'reg140': 140, 'reg2858GHz': 28, 'reg142': 142, 'reg145': 145, 'reg144': 144, 'reg147': 147, 'reg2154GHz': 21, 'reg5558GHz': 55, 'reg7152GHz': 71, 'reg252': 252, 'reg7452GHz': 74, 'reg5258GHz': 52, 'reg5058GHz': 50, 'reg5158GHz': 51, 'reg242': 242, 'reg127': 127, 'reg9152GHzParabolicantenna': 91, 'reg241': 241, 'reg246': 246, 'reg247': 247, 'reg6551GHz': 65, 'reg245': 245, 'reg8758GHz': 87, 'reg248': 248, 'reg249': 249, 'reg2558GHz': 25, 'reg2458GHz': 24, 'reg124': 124, 'reg7352GHz': 73, 'reg198': 198, 'reg158GHz': 1, 'reg244': 244, 'reg243': 243, 'reg6451GHz': 64, 'reg15': 15, 'reg8352GHz': 83, 'reg254': 254, 'reg8451GHz': 84, 'reg1958GHz': 19, 'reg4958GHz': 49, 'reg200': 200, 'reg240': 240, 'reg193': 193, 'reg251': 251, 'reg3654GHz': 36, 'reg253': 253, 'reg8551GHz52GHz': 85, 'reg2258GHz': 22, 'reg3852GHz': 38, 'reg1254GHz': 12, 'reg7752GHz': 77, 'reg1158GHz': 11, 'reg3758GHz': 37, 'reg9949GHz29dBiantenna': 99, 'reg130': 130, 'reg229': 229, 'reg9251GHzParabolicantenna': 92, 'reg8049GHz': 80, 'reg7849GHz': 78, 'reg9752GHz': 97, 'reg2054GHz': 20, 'reg8949GHz': 89, 'reg235': 235, 'reg3054GHz': 30, 'reg174': 174, 'reg7052GHz': 70, 'reg176': 176, 'reg160': 160, 'reg170': 170, 'reg171': 171, 'reg172': 172, 'reg10458GHzNoRTTT': 104, 'reg178': 178, 'reg179': 179, 'reg166': 166, 'reg116': 116, 'reg117': 117, 'reg114': 114, 'reg115': 115, 'reg112': 112, 'reg458GHzWithRTTT': 4, 'reg105': 105, 'reg111': 111, 'reg206': 206, 'reg207': 207, 'reg204': 204, 'reg164': 164, 'reg202': 202, 'reg203': 203, 'reg118': 118, 'reg119': 119, 'reg7954GHz': 79, 'reg220': 220, 'reg1058GHz': 10, 'reg227': 227, 'reg5654GHz': 56, 'reg205': 205, 'reg1759GHz': 17, 'reg954GHz': 9, 'reg8849GHz': 88, 'reg2958GHz': 29, 'reg10048GHz': 100, 'reg4858GHz': 48, 'reg4758GHz': 47, 'reg163': 163, 'reg162': 162, 'reg161': 161, 'reg9054GHzParabolicantenna': 90, 'reg167': 167, 'reg5858GHz': 58, 'reg5958GHz': 59, 'reg3458GHz': 34, 'reg169': 169, 'reg168': 168, 'reg9849GHz27dBiantenna': 98.

The wireless link bandwidth cap in MHz. Zero indicates no bandwidth cap.

The license key encryption algorithms available. Enumeration: 'aES192bit': 2, 'none': 0, 'aES128bit': 1, 'aES256bit': 3.

The license key security level. Enumeration: 'uCAPL': 2, 'fIPS': 1, 'normal': 0.

The license key group access setting. Note that for HCMP topology, license group access must be enabled. Enumeration: 'disabled': 0, 'enabled': 1.

The license key Out-Of-Band (OOB) support setting. Enumeration: 'disabled': 0, 'enabled': 1.

The license key Ethernet SFP Port support setting. Enumeration: 'disabled': 0, 'enabled': 1.

The license key Ethernet Auxiliary Port support setting. Enumeration: 'disabled': 0, 'enabled': 1.

The license key capacity. Note that for HCMP topology, license capacity must be full. Enumeration: 'lite': 2, 'full': 0, 'mid': 1.

The license key maximum TDM channels setting. Zero indicates TDM not available.

The license key IEEE-1588 support setting. Enumeration: 'disabled': 0, 'enabled': 1.

The license key SyncE support setting. Enumeration: 'disabled': 0, 'enabled': 1.

The license key IPv6 support setting. Enumeration: 'disabled': 0, 'enabled': 1.

The minimum firmware version required to support this license key.

The license key full capability trial period status. Enumeration: 'available': 0, 'active': 1, 'inactive': 2, 'expired': 3, 'unavailable': 4.

The remaining time for the license key full capability trial period.

If the full capability trial license period is about to expire then purchase a license upgrade from your reseller. Enumeration: 'fullCapabilityTrialExpiringInLessThan6Days': 2, 'fullCapabilityTrialExpiringInLessThan4Days': 4, 'fullCapabilityTrialExpiringInLessThan5Days': 3, 'fullCapabilityTrialExpiringInLessThan7Days': 1, 'fullCapabilityTrialExpiringInLessThan3Days': 5, 'fullCapabilityTrialExpiringInLessThan1Day': 7, 'fullCapabilityTrialExpiringInLessThan2Days': 6, 'fullCapabilityTrialNotActiveOrMoreThan7DaysRemaining': 0, 'fullCapabilityTrialHasExpired': 8.

The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity. Enumeration: 'noError': 0, 'mismatchDetected': 1.

The license key TDD Synchronization support setting. Enumeration: 'disabled': 0, 'enabled': 1.

Maximum licensed range for the wireless link in tenths of km. A value of zero indicates that the maximum link range is not limited by the license.

The license key maximum trial period, in days.

The license key Radio Aware Routing support setting. Enumeration: 'disabled': 0, 'dLEP': 2, 'mAB': 1, 'mABandDLEP': 3.

The HAZLOC/ATEX Configuration of this unit. The Gas Group is configured by the license key. Enumeration: 'gasGroupD': 4, 'gasGroupB': 2, 'gasGroupA': 1, 'gasGroupC': 3, 'nonHAZLOCUnit': 0.

The minimum long firmware version required to support this license key.

The license High Capacity MultiPoint support setting Enumeration: 'disabled': 0, 'masterEnabled': 2, 'slaveEnabled': 1, 'masterandSlaveEnabled': 3.

Number of entries in the licenseInstancedTable.

Instanced license table

Table LicenseInstancedTable

Used to index the LicenseInstancedTable.

The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity. Enumeration: 'noError': 0, 'mismatchDetected': 1.

The license TLS Rekey support setting Enumeration: 'disabled': 0, 'enabled': 1.

The license Advance High Capacity MultiPoint support setting Enumeration: 'disabled': 0, 'masterEnabled': 2, 'slaveEnabled': 1, 'masterandSlaveEnabled': 3.

The minimum long firmware version of 650-Emulation required to support this license key.

Initial target range used in installation +/-1, expressed in tenths of a kilometer. When Auto-Ranging this must be set to 0

Type of ranging to use during installation, either Auto-Ranging or use a selectable Target Range Enumeration: 'targetRange': 4, 'auto0to200km': 2, 'auto0to100km': 1, 'auto0to250km': 3, 'auto0to40km': 0.

A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert Enumeration: 'wrongPeer': 1, 'ok': 0.

Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'armed': 1, 'disarmed': 0.

The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved

Filename of the Software Upgrade to be loaded from the TFTP Server

Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished. Continuing with the software upgrade will cause spectrum management (DSO) channel metrics collection to stop. The wireless unit will no longer search for the optimal operational radio channel. The performance of this wireless link may deterioate over time. If operating in a regulatory band where RADAR detection is mandatory you must complete the software upgrade and reboot the unit. Channel metrics collection will only be restarted after the wireless unit has been rebooted

The current status of the TFTP Software upgrade process Enumeration: 'uploadsuccessfulprogrammingFLASH': 2, 'upgradesuccessfulreboottorunthenewsoftwareimage': 3, 'idle': 0, 'upgradefailed': 4, 'upgradewarning': 5, 'uploadinprogress': 1.

Descriptive text describing the status of the TFTP Software upgrade process, including any error details

Any additional text describing the status of the TFTP Software upgrade process, including any error details

This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled) Enumeration: 'yes': 1, 'no': 0.

This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled) Enumeration: 'yes': 1, 'no': 0.

This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80)

This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the License Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443)

This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23)

This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled) Enumeration: 'yes': 1, 'no': 0.

The type of Internet address specified by the associated tFTPServerInternetAddress. Enumeration: 'dns': 16, 'ipv6z': 4, 'unknown10': 9, 'unknown': 0, 'unknown12': 11, 'unknown13': 12, 'ipv4z': 3, 'unknown15': 14, 'unknown16': 15, 'unknown14': 13, 'unknown6': 5, 'ipv4': 1, 'unknown11': 10, 'ipv6': 2, 'unknown8': 7, 'unknown9': 8, 'unknown7': 6.

INET address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved

The lowest modulation mode at which Ethernet Data traffic will be bridged over the wireless link Enumeration: 'modTransient9': 21, 'modTransient8': 19, 'modTransient7': 17, 'modTransient6': 13, 'modTransient5': 11, 'modTransient4': 9, 'modTransient3': 7, 'modTransient2': 5, 'modTransient1': 3, 'mod256qam81percentDual': 24, 'mod64qam75percentSingle': 10, 'mod64qam92percentSingle': 12, 'mod16qam63percentSingleA': 6, 'mod16qam63percentSingleB': 15, 'mod16qam87percentSingle': 8, 'mod64qam92percentDual': 22, 'modBpsk63percent': 1, 'modQpsk63percentSingle': 2, 'mod16qam63percentDual': 16, 'modTransient10': 23, 'mod16qam87percentDual': 18, 'modQpsk87percentSingle': 4, 'mod256qam81percentSingle': 14, 'modAcquisition': 0, 'mod64qam75percentDual': 20.

This controls whether or not TFTP client is enabled, i.e. if this is disabled (0) then the unit will not respond to any TFTP software download requests. (Factory default = Enabled) Enumeration: 'disabled': 0, 'enabled': 1.

Number of entries in the mgmtInstancedTable.

Instanced management table.

Table MgmtInstancedTable

Used to index values in the mgmtInstancedTable

A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert Enumeration: 'wrongPeer': 1, 'ok': 0.

IP Address of the TFTP Server.

Determines whether the unit is armed for antenna alignment, and whether it emits audible installation tones to indicate the state and strength of the received signal. Alternatively, configuration changes may be made without arming the unit (typically once a link has already been established). Note: while armed, a unit will have reduced link performance and functionality. Enumeration: 'armWithTones': 0, 'armWithoutTones': 1, 'changeConfigWithoutArming': 2.

Provides configuration options for sharing the available wireless capacity between the transmit and receive directions. Fixed link symmetry is defined by a ratio of the burst duration for the transmit direction to the burst duration for the receive direction. Permitted settings are 5:1, 3:1, 2:1, 1:1, 1:2, 1:3, 1:5. The 1:1 option provides fixed symmetric operation. The adaptive option selects transmit and receive burst durations automatically in response to the offered Ethernet traffic in each link direction. This attribute is valid only for a unit configured as a TDD Master Enumeration: 'symmetry5to1': 6, 'symmetry3to1': 4, 'symmetry2to1': 1, 'symmetry1to5': 7, 'symmetryAdaptive': 0, 'symmetry1to1': 2, 'symmetry1to2': 3, 'symmetry1to3': 5.

The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard Enumeration: 'modQpsk87percent': 2, 'mod256qam81percent': 7, 'mod64qam92percent': 6, 'modQpsk63percent': 1, 'mod16qam63percent': 3, 'modBpsk63percent': 0, 'mod16qam87percent': 4, 'mod64qam75percent': 5.

Optimizes the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimize transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimize transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols. Enumeration: 'tDMTraffic': 1, 'iPTraffic': 0.

Transmit Color Code. This attribute need only be considered when the unit is installed in a network of wireless units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Rx Color Code parameter at the far end of the link. Enumeration: 'a': 0, 'c': 2, 'b': 1, 'e': 4, 'd': 3.

Receive Color Code. This attribute need only be considered when the unit is installed in a network of wireless units and where some of the units are operating on the same frequency. In this case, the value would normally be derived by a network planner. In all other cases, it is recommended that this attribute is left at the default value. NOTE: For the link to operate, the value of this parameter must in all cases match the value of the Tx Color Code parameter at the far end of the link. Enumeration: 'a': 0, 'c': 2, 'b': 1, 'e': 4, 'd': 3.

Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link

Number of entries in the PhyControlInstancedTable.

Table PhyControlInstancedTable

Used to index the PhyControlInstancedTable.

Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link

The wireless link loss expressed in tenths of a dB

Receive power expressed in tenths of a dBm

The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dB

Transmit power expressed in tenths of a dBm

Current active receive channel

Current active transmit channel

Current receive frequency expressed in integer MHz

Current transmit frequency expressed in integer MHz

Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dB

Current receive frequency expressed as KHz

Current transmit frequency expressed as KHz

Raw receive power expressed in tenths of a dBm

Distance between the two peer wireless units expressed in tenths of a kilometer

Current active receive modulation mode

Current active transmit modulation mode

Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal. Enumeration: 'acquiring': 2, 'searching': 1, 'registering': 0.

MAC Address of the peer wireless unit

Number of entries in the phyInstancedStatusTable.

Instanced PHY status table.

Table PhyInstancedStatusTable

Used to index the phyInstancedStatusTable.

The link loss measurement = Peer Tx_Power(dBm) - Local Rx_Power(dBm) + 2 x Antenna_Pattern(dBi)

Receive power histogram

The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude

Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input

Distance between the two peer wireless units

Current active receive modulation mode Enumeration: 'modTransient9': 21, 'modTransient8': 19, 'modTransient7': 17, 'modTransient6': 13, 'modTransient5': 11, 'modTransient4': 9, 'modTransient3': 7, 'modTransient2': 5, 'modTransient1': 3, 'mod256qam81percentDual': 24, 'mod64qam75percentSingle': 10, 'mod64qam92percentSingle': 12, 'mod16qam63percentSingleA': 6, 'mod16qam63percentSingleB': 15, 'mod16qam87percentSingle': 8, 'mod64qam92percentDual': 22, 'modBpsk63percent': 1, 'modQpsk63percentSingle': 2, 'mod16qam63percentDual': 16, 'modTransient10': 23, 'mod16qam87percentDual': 18, 'modQpsk87percentSingle': 4, 'mod256qam81percentSingle': 14, 'modAcquisition': 0, 'mod64qam75percentDual': 20.

Current active transmit modulation mode Enumeration: 'modTransient9': 21, 'modTransient8': 19, 'modTransient7': 17, 'modTransient6': 13, 'modTransient5': 11, 'modTransient4': 9, 'modTransient3': 7, 'modTransient2': 5, 'modTransient1': 3, 'mod256qam81percentDual': 24, 'mod64qam75percentSingle': 10, 'mod64qam92percentSingle': 12, 'mod16qam63percentSingleA': 6, 'mod16qam63percentSingleB': 15, 'mod16qam87percentSingle': 8, 'mod64qam92percentDual': 22, 'modBpsk63percent': 1, 'modQpsk63percentSingle': 2, 'mod16qam63percentDual': 16, 'modTransient10': 23, 'mod16qam87percentDual': 18, 'modQpsk87percentSingle': 4, 'mod256qam81percentSingle': 14, 'modAcquisition': 0, 'mod64qam75percentDual': 20.

Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal. Enumeration: 'acquiring': 2, 'searching': 1, 'registering': 0.

MAC Address of the peer wireless unit

Raw receive power

Transmit power histogram

PCB temperature expressed in Celsius

The unit is out of calibration Enumeration: 'bandwidthvariantunsupportedPAsShutdown': 3, 'outOfCalibrationPAsShutdown': 4, 'calibrated': 0, 'invalidCalibration': 2, 'partialCalibration': 1.

The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys Enumeration: 'regIncompatibleLicenseKeys': 1, 'regOK': 0.

Spectrum Management was unable to locate a suitable wireless channel to operate on Enumeration: 'noWirelessChannelAvailable': 1, 'ok': 0.

The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic Enumeration: 'disabledBySNMPifAdminStatus': 1, 'ok': 0.

The SNMP ifAdminStatus of the interface has disabled Ethernet traffic Enumeration: 'disabledBySNMPifAdminStatus': 1, 'ok': 0.

If the SFP link is not OK, there are five possible causes: Either a SFP has been installed but the license key does not include SFP fiber support, a fiber link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), a fiber link could not be established and LOS is detected (i.e. no optical carrier is detected), the installed SFP is not supported or the installed SFP failed to initialize correctly. NB: a change of status may generate an SNMP trap and/or SMTP email alert Enumeration: 'ok': 0, 'sFPInitializationFailed': 5, 'installedSFPNotSupported': 4, 'fiberLinkNotEstablishedButLOSNotDetected': 2, 'installedSFPNotLicensed': 1, 'fiberLinkNotEstablishedAndLOSDetected': 3.

The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch Enumeration: 'noError': 0, 'mismatchDetected': 1.

A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions, or have different TDD Frame Configuraton Modes (Standard/Expert) in HCMP topology. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert Enumeration: 'differentSoftwareVersionsRunning': 2, 'incompatibleProductVariants': 1, 'tDDFrameConfigurationModeMismatch': 3, 'ok': 0.

An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference. Enumeration: 'locked': 0, 'pTPSYNCNotConnected': 5, 'notSynchronizedNoGPSSyncIn': 4, 'holdoverNoGPSSyncIn': 2, 'acquiringLock': 8, 'inactive': 9, 'holdover': 1, 'initialising': 6, 'notSynchronized': 3, 'clusterTimingMaster': 7.

The SNMP ifAdminStatus of the interface has disabled Ethernet traffic Enumeration: 'disabledBySNMPifAdminStatus': 1, 'ok': 0.

Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired. Enumeration: 'ok': 0, 'synchronizationLost': 1, 'referenceSignalLost': 2.

The remote node of this link has been configured with a different link mode optimization Enumeration: 'ok': 0, 'linkModeOptimizationMismatch': 1.

The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured. Enumeration: 'noError': 0, 'mismatchDetected': 1.

The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image. Enumeration: 'secureModeIsNotSupported': 3, 'secureModeIsConfiguredButNotActive': 2, 'secureModeIsNotConfigured': 1, 'secureModeIsActive': 0.

Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode Enumeration: 'bridgingDisabled': 1, 'bridgingEnabled': 0.

The SNMP ifAdminStatus of the interface has disabled Ethernet traffic Enumeration: 'disabledBySNMPifAdminStatus': 1, 'ok': 0.

The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured. Enumeration: 'noError': 0, 'mismatchDetected': 1.

The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This alarm is only raised if the license specifies a maximum link range and the trial license is not active. Enumeration: 'maxLinkRangeOK': 0, 'maxLinkRangeExceeded': 1.

The SNMP ifAdminStatus of the interface has disabled Ethernet traffic Enumeration: 'disabledBySNMPifAdminStatus': 1, 'ok': 0.

The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. Enumeration: 'noError': 0, 'mismatchDetected': 1.

The local and remote ODUs have different services configured. Enumeration: 'portAllocationOK': 0, 'mismatchinOutofBandRemoteManagementService': 1.

Transparent Clock will not function properly because SFP, the selected clock source port is not FIBER Enumeration: 'invalidTransparentClockSourcePort': 1, 'ok': 0.

Number of entries in the alarmInstancedTable.

Instanced alarm table.

Table AlarmInstancedTable

Used to index values in the alarmInstancedTable

A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions, or have different TDD Frame Configuraton Modes (Standard/Expert) in HCMP topology. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert Enumeration: 'differentSoftwareVersionsRunning': 2, 'incompatibleProductVariants': 1, 'tDDFrameConfigurationModeMismatch': 3, 'ok': 0.

The remote node of this link has been configured with a different link mode optimization Enumeration: 'ok': 0, 'linkModeOptimizationMismatch': 1.

Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode Enumeration: 'bridgingDisabled': 1, 'bridgingEnabled': 0.

The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This alarm is only raised if the license specifies a maximum link range and the trial license is not active. Enumeration: 'maxLinkRangeOK': 0, 'maxLinkRangeExceeded': 1.

The local and remote ODUs have different services configured. Enumeration: 'portAllocationOK': 0, 'mismatchinOutofBandRemoteManagementService': 1.

Current status of the wireless link. A state of Up on a green background indicates that a wireless link is established Enumeration: 'down': 1, 'up': 0.

The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys Enumeration: 'regIncompatibleLicenseKeys': 1, 'regOK': 0.

Alarm condition indicates that the unit's license is not secure enough for FIPS approved mode. Enumeration: 'licensesignaturealarmisnotrelevant': 2, 'licenseisDSA2048signed': 0, 'licenseisDSA1024signed': 1.

The target Rx power level (dBm) at the HCMP Master that the HCMP Slaves try to reach by automatically adjusting their transmit power. The same value must be set in both the HCMP Master and Slaves as it used by the Slave to set its transmit power accurately before the wireless link is established.

This must be set to the same value as the Maximum Transmit Power attribute on the HCMP Master. This is required by the HCMP Slave for initial transmit power estimation.

Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address Enumeration: 'disabled': 0, 'enabled': 1.

Port number of the SMTP server

The 'from' email address used when constructing the automatically generated e-mail message

The 'to' email address used when constructing the automatically generated e-mail message

This controls which SMTP messages the unit will send Bits: 'mainPSUPortUpDown': 3, 'auxPortUpDown': 2, 'listenBeforeTalk': 15, 'wirelessPortUpDown': 7, 'dFSImpulseInterference': 5, 'nIDULanPortUpDown': 0, 'sFPPortUpDown': 1, 'channelChange': 6, 'enabledDiagnosticAlarms': 4.

The type of Internet address specified by the associated sMTPServerInternetAddress. Enumeration: 'dns': 16, 'ipv6z': 4, 'unknown10': 9, 'unknown': 0, 'unknown12': 11, 'unknown13': 12, 'ipv4z': 3, 'unknown15': 14, 'unknown16': 15, 'unknown14': 13, 'unknown6': 5, 'ipv4': 1, 'unknown11': 10, 'ipv6': 2, 'unknown8': 7, 'unknown9': 8, 'unknown7': 6.

Internet address of the SMTP server

IP Address of the SMTP Server.

The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute

The SNMP community string. NB: A system reboot is required to activate changes to this attribute

Number of entries in the sNMPTrapTable.

SNMP trap configuration table.

Table SNMPTrapTable

SNMP trap value, used to index the SNMPTrapTable.

Destination port for SNMP Traps (default=162). NB: A system reboot is required to activate changes to this attribute.

The type of Internet address specified by the associated sNMPTrapInternetAddress. Enumeration: 'dns': 16, 'ipv6z': 4, 'unknown10': 9, 'unknown': 0, 'unknown12': 11, 'unknown13': 12, 'ipv4z': 3, 'unknown15': 14, 'unknown16': 15, 'unknown14': 13, 'unknown6': 5, 'ipv4': 1, 'unknown11': 10, 'ipv6': 2, 'unknown8': 7, 'unknown9': 8, 'unknown7': 6.

The Internet address to which all SNMP Traps are sent.

A value of 0 disables the sending of SNMP trap to corresponding receiver. A value of 1 enables the sending of SNMP trap to corresponding receiver. Enumeration: 'disabled': 0, 'enabled': 1.

IP Address(es) of the SNMP Trap Server.

The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute Enumeration: 'v2c': 1, 'v1': 0.

This controls which SNMP Traps the unit will send Bits: 'mainPSUPortUpDown': 1, 'auxPortUpDown': 0, 'listenBeforeTalk': 13, 'wirelessPortUpDown': 6, 'dFSImpulseInterference': 4, 'authenticationFailure': 2, 'nIDULanPortUpDown': 14, 'sFPPortUpDown': 15, 'channelChange': 5, 'enabledDiagnosticAlarms': 3, 'coldStart': 7.

Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributes Bits: 'tDDSynchronizationAlarm': 12, 'installStatus': 6, 'capacityVariantMismatch': 19, 'portState': 0, 'sNTPSynchronizationFailed': 14, 'syslogClientDisabledWarning': 23, 'linkModeOptimizationMismatch': 11, 'incompatibleMasterAndSlave': 1, 'licenseSignatureLengthAlarm': 16, 'regulatoryBand': 7, 'incompatibleRegulatoryBands': 2, 'wirelessLinkDisabledWarning': 13, 'unitOutOfCalibration': 4, 'syslogLocalWrapped': 8, 'wirelessLinkStatus': 17, 'syslogLocalNearlyFull': 9, 'syslogDisabledWarning': 10, 'noWirelessChannelAvailable': 15, 'installArmState': 5, 'maximumLinkRangeExceeded': 3, 'secureModeAlarm': 22, 'remainingFullCapacityTrialTime': 20, 'dataBridgingStatus': 21, 'tDMAlarms': 18.

Controls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient events (i.e. not associated with an alarm or status value) are only sent when required and not at start-up. Enumeration: 'disabled': 0, 'enabled': 1.

SNTP control state Enumeration: 'disabled': 0, 'enabled': 1.

The SNTP server polling interval

If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP Enumeration: 'inSync': 1, 'noSync': 0.

Last SNTP sync time

System clock presented as local time

Time zone offsets from Greenwich Mean Time (GMT) Enumeration: 'gmtPlus1030': 45, 'gmtMinus0900': 6, 'gmtPlus0300': 30, 'gmtPlus1130': 47, 'gmtMinus0800': 8, 'gmtMinus0100': 22, 'gmtZero': 24, 'gmtPlus1300': 50, 'gmtPlus0430': 33, 'gmtPlus0800': 40, 'gmtPlus0030': 25, 'gmtMinus0330': 17, 'gmtMinus1000': 4, 'gmtPlus0900': 42, 'gmtMinus0700': 10, 'gmtPlus0700': 38, 'gmtPlus0630': 37, 'gmtMinus1100': 2, 'gmtMinus0600': 12, 'gmtMinus0230': 19, 'gmtPlus0930': 43, 'gmtMinus0500': 14, 'gmtPlus0530': 35, 'gmtMinus0400': 16, 'gmtPlus0600': 36, 'gmtPlus0330': 31, 'gmtMinus0830': 7, 'gmtPlus1000': 44, 'gmtPlus1230': 49, 'gmtMinus0930': 5, 'gmtMinus1200': 0, 'gmtPlus0100': 26, 'gmtPlus0400': 32, 'gmtPlus1100': 46, 'gmtMinus0130': 21, 'gmtPlus0500': 34, 'gmtMinus1030': 3, 'gmtPlus0230': 29, 'gmtMinus0730': 9, 'gmtMinus0300': 18, 'gmtPlus0830': 41, 'gmtMinus0030': 23, 'gmtMinus0200': 20, 'gmtPlus0130': 27, 'gmtPlus0730': 39, 'gmtMinus1130': 1, 'gmtMinus0630': 11, 'gmtPlus1200': 48, 'gmtMinus0430': 15, 'gmtMinus0530': 13, 'gmtPlus0200': 28.

Daylight Saving Time Enumeration: 'disabled': 0, 'enabled': 1.

Specifies the primary SNTP server, determining the order in which the servers are tried. Enumeration: 'server1': 0, 'server2': 1.

Time (in seconds) to wait before retrying communications with an unresponsive primary SNTP server. Setting the value to 0 disables the timer.

Number of times the device will retry after an SNTP server fails to respond.

Time (in seconds) the device will wait for a response from an SNTP server.

Number of entries in the SNTPServerTable.

Table SNTPServerTable

Index range for the SNTPServerTable.

The IP port number of the SNTP server. Defaults to port 123.

Status message reflecting the result of communications with the SNTP server when last polled

The type of Internet address specified by the associated sNTPServerInternetAddress. Enumeration: 'dns': 16, 'ipv6z': 4, 'unknown10': 9, 'unknown': 0, 'unknown12': 11, 'unknown13': 12, 'ipv4z': 3, 'unknown15': 14, 'unknown16': 15, 'unknown14': 13, 'unknown6': 5, 'ipv4': 1, 'unknown11': 10, 'ipv6': 2, 'unknown8': 7, 'unknown9': 8, 'unknown7': 6.

The Internet address of a valid SNTP server

IP Address of the SNTP Server.

Authentication protocol to be used for this SNTP server. Options are None (default) or MD5. Enumeration: 'none': 0, 'sHA1': 2, 'mD5': 1.

SNTP key identifier. Note: Key 0 is reserved for testing using the well-known key all zeroes.

Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory Enumeration: 'consoleReboot': 1, 'running': 0.

Current software version

Hardware platform version

Secondary software version, used when the primary software image is invalid or erased

Boot code software version

Average data rate over the last one second interval (kbps)

Average data rate over the last one second interval (kbps)

Average data rate over the last one second interval (kbps)

Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision

Current status of the wireless link Enumeration: 'acquiring': 3, 'registering': 1, 'up': 0, 'searching': 2, 'initialising': 5, 'radarCAC': 4.

Reciprocal of the byte error ratio calculated since the last reset of the system counters

The reason for the current receive modulation mode Enumeration: 'restrictedBecauseFullCapabilityTrialLicenseExpired': 9, 'runningAtMaximumReceiveModeForChannelBandwidth': 7, 'restrictedBecauseTheLinkParametersAreUpdating': 4, 'runningAtUserConfiguredMaxModulationMode': 1, 'runningAtMaximumReceiveMode': 0, 'restrictedBecauseChannelChangeIsInProgress': 5, 'restrictedBecauseOfByteErrorsOnTheWirelessLink': 3, 'limitedByTheWirelessConditions': 8, 'restrictedBecauseInstallationIsArmed': 2, 'restrictedDueToTheLowEthernetLinkSpeed': 6.

Link availability bridging Ethernet Data traffic calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision

Number of entries in the pubInstancedStatsTable.

Instanced Public stats table.

Table PubInstancedStatsTable

Used to index the pubInstancedStatsTable.

Histogram of the average link receive data rate.

Histogram of the average link transmit data rate.

Histogram of the link aggregate data rate.

Link availability calculated since the last reset of the system counters

Current status of the wireless link. A state of 'Up' on a green background indicates that a wireless link is established Enumeration: 'acquiring': 3, 'registering': 1, 'up': 0, 'searching': 2, 'initialising': 5, 'radarCAC': 4.

A brief description of the reason for the current receive modulation mode Enumeration: 'acquiringLink': 10, 'restrictedBecauseFullCapabilityTrialLicenseExpired': 9, 'runningAtMaximumReceiveModeForChannelBandwidth': 7, 'restrictedBecauseTheLinkParametersAreUpdating': 4, 'runningAtUserConfiguredMaxModulationMode': 1, 'runningAtMaximumReceiveMode': 0, 'restrictedBecauseChannelChangeIsInProgress': 5, 'restrictedBecauseOfByteErrorsOnTheWirelessLink': 3, 'limitedByTheWirelessConditions': 8, 'restrictedBecauseInstallationIsArmed': 2, 'restrictedDueToTheLowEthernetLinkSpeed': 6.

Link availability for bridging Ethernet Data traffic calculated since the last reset of the system counters

Reciprocal of the byte error ratio calculated since the last reset of the system counters

Cumulative total of octets transmitted in data or management service at the wireless interface. This excludes wireless MAC headers, MAC management messages, and Null bytes.

Cumulative total of octets transmitted at the wireless interface. This includes data service, management service, wireless MAC headers, MAC management messages, and Null bytes.

Cumulative total of octets including wireless MAC headers transmitted in data or management service at the wireless interface. This excludes MAC management messages and Null bytes.

erroredSeconds count for any second period containing one or more codeword errors since the last reset of the system counters.

severelyErroredSeconds count for any second period containing ten or more codeword errors since the last reset of the system counters.

unavailableSeconds count for any second when Data Bridging Status = Disabled since the last reset of the system counters. Note erroredSeconds and severelyErroredSeconds are not incremented when the link is unavailable.

The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctly. TLS RSA Encryption Algorithm is not compatible with Link Name access method. Enumeration: 'tLSRSA': 4, 'none': 0, 'pSKAES128bit': 1, 'pSKAES192bit': 2, 'tLSPSK128bit': 5, 'tLSPSK256bit': 6, 'pSKAES256bit': 3.

The minimum level of security that is supported on the device Enumeration: 'none': 0, 'aES128bitTLSRSA': 1, 'aES256bitTLSRSA': 2.

TDD Synchronization Mode selection Enumeration: 'disabled': 0, 'enabled': 1.

The maximum link range between the HCMP Master and any HCMP Slave. The same value must be used on both the HCMP Master and its Slaves.

The maximum number of HCMP Slaves that an HCMP Master can simultaneously connect to. The same value has to be used in both the HCMP Master and its Slaves.

Provides configuration options for sharing the available wireless capacity among all Slaves between the transmit and receive directions. Option x to y is the ratio of Total Downlink capacity to Total Uplink Capacity. The same value has to be used in both the HCMP Master and its Slaves. Enumeration: 'symmetry3to1': 1, 'symmetry2to1': 2, 'symmetry4to1': 0, 'symmetry1to4': 6, 'symmetry1to1': 3, 'symmetry1to2': 4, 'symmetry1to3': 5.

Enable or disable the syslog client Enumeration: 'disabled': 0, 'enabled': 1.

The syslog service has been enabled or disabled Enumeration: 'disabled': 0, 'enabled': 1.

Number of entries in the userTable

The User Table Control group contains objects specifically for user account management.

Table UserTable

used to index values in the userTable.

User name which must be entered, along with the appropriate password, in order to gain access to the system.

Role of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security settings. A Read Only user can view settings, but cannot make any changes. Enumeration: 'systemAdministrator': 1, 'readOnly': 0, 'securityOfficer': 2.

Enable / Disable the selected user Enumeration: 'disabled': 0, 'enabled': 1.

User password, which must be entered in order to gain access to the system.

Enable support of Microwave Adaptive Bandwidth Protocol. MAB is disabled if link symmetry is configured as Adaptive Enumeration: 'disabled': 0, 'enabled': 1.

The Nominal modulation mode is the desired modulation mode. MAB VSM packets are generated when the current modulation mode falls below the nominal modulation. Enumeration: 'modTransient9': 21, 'modTransient8': 19, 'modTransient7': 17, 'modTransient6': 13, 'modTransient5': 11, 'modTransient4': 9, 'modTransient3': 7, 'modTransient2': 5, 'modTransient1': 3, 'mod256qam81percentDual': 24, 'mod64qam75percentSingle': 10, 'mod64qam92percentSingle': 12, 'mod16qam63percentSingleA': 6, 'mod16qam63percentSingleB': 15, 'mod16qam87percentSingle': 8, 'mod64qam92percentDual': 22, 'modBpsk63percent': 1, 'modQpsk63percentSingle': 2, 'mod16qam63percentDual': 16, 'modTransient10': 23, 'mod16qam87percentDual': 18, 'modQpsk87percentSingle': 4, 'mod256qam81percentSingle': 14, 'modAcquisition': 0, 'mod64qam75percentDual': 20.

The minimum interval (in seconds) between successive MAB vendor specific messages (VSM). These VSM are sent when the current transmit capacity falls below the configured MAB Nominal Modulation Mode. Enumeration: 'transmissionInterval10s': 1, 'transmissionInterval1s': 0, 'transmissionInterval60s': 2.

The period (in seconds) over which transmit capacity is averaged over to determine when the wireless link has degraded

Maintenance Levels (0-7) determines the destination MAC address of MAB vendor specific messages.

This controls whether MAB vendor specific messages (VSM) packets use VLAN tags or not. Enumeration: 'noVLANTagging': 0, 'iEEE8021QTaggedCTagType8100': 1.

This VLAN VID (0-4094) will be included in MAB vendor specific messages (VSM) packets.

This VLAN Priority (0-7) will be included in MAB vendor specific messages (VSM) packets.

Current state of MAB Protocol. A state of 'Normal' on a green background indicates that a wireless link is operating at nominal capacity Enumeration: 'degraded': 1, 'normal': 0.

The nominal Tx capacity used in MAB Vendor Specific Messages for the selected nominal modulation mode

The current Tx capacity of the wireless link used in the last MAB Vendor Specific Message transmitted.

Select ports on which Cable Diagnostics must be executed Bits: 'auxPort': 6, 'mainPSUPort': 7.

Set this attribute to 'Test in Progress' to start a Cable Diagnostics test Enumeration: 'startTest': 0, 'testInProgress': 1.

Normal Ethernet operation is disrupted when a Cable Diagnostics test is in progress Enumeration: 'idle': 0, 'testInProgress': 1.

Number of rows in the Cable Diagnostics Result Table.

Table CableDiagnosticsResultTable

Cable Diagnostics Port value used to index into the result table.

The Date and Time when a Cable Diagnostics test was last executed

The result of the most recent execution of Cable Diagnostics on cable pair 1. According to the T658B wiring scheme, pair 1 is pins 4 & 5 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test. Enumeration: 'ok': 0, 'unknown': 1, 'openCircuit': 4, 'shortCircuit': 5, 'notTested': 3, 'inProgress': 2.

The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).

The result of the most recent execution of Cable Diagnostics on cable pair 2. According to the T658B wiring scheme, pair 2 is pins 1 & 2 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test. Enumeration: 'ok': 0, 'unknown': 1, 'openCircuit': 4, 'shortCircuit': 5, 'notTested': 3, 'inProgress': 2.

The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).

The result of the most recent execution of Cable Diagnostics on cable pair 3. According to the T658B wiring scheme, pair 3 is pins 3 & 6 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test. Enumeration: 'ok': 0, 'unknown': 1, 'openCircuit': 4, 'shortCircuit': 5, 'notTested': 3, 'inProgress': 2.

The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).

The result of the most recent execution of Cable Diagnostics on cable pair 4. According to the T658B wiring scheme, pair 4 is pins 7 & 8 on the RJ45 socket on the ODU. Open Circuit is reported when the impedance is greater than 330 ohms. Short Circuit is reported when the impedance is less than 33 ohms. Unknown is reported when a continuous signal is received from the link partner for 125 ms, preventing start of the test. Enumeration: 'ok': 0, 'unknown': 1, 'openCircuit': 4, 'shortCircuit': 5, 'notTested': 3, 'inProgress': 2.

The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than 160 meters (525 feet) may not be detected. The error margin is +/-2 meters (6.5 feet).

Device MAC address

The ESN assigned to this device

The MSN assigned to this device

Number of entries in the AuthorizationControlTable.

AuthorizationControlTable - used to validate an RM trying to connect to it.

Table AuthorizationControlTable

Authorization Control Table Index

MAC Address of Remote Modules.

Whether this Remote Module is enabled. Only Enabled Remote Modules are allowed to connect to this device. Enumeration: 'disabled': 0, 'enabled': 1.

MAC Address of Remote Modules.

Whether this Remote Module is enabled. Only Enabled Remote Modules are black listed; they cannot connect to this ODU. Enumeration: 'disabled': 0, 'enabled': 1.

Enable/Disable DNS Resolver. Enumeration: 'disabled': 0, 'enabled': 1.

Specifies the primary DNS server, determining the order in which the servers are tried. Enumeration: 'server1': 0, 'server2': 1.

Number of entries in the DNSServerTable.

Table DNSServerTable

Index range for the DNSServerTable.

The type of Internet address specified by the associated dNSServerInternetAddress. Enumeration: 'dns': 16, 'ipv6z': 4, 'unknown10': 9, 'unknown': 0, 'unknown12': 11, 'unknown13': 12, 'ipv4z': 3, 'unknown15': 14, 'unknown16': 15, 'unknown14': 13, 'unknown6': 5, 'ipv4': 1, 'unknown11': 10, 'ipv6': 2, 'unknown8': 7, 'unknown9': 8, 'unknown7': 6.

IP Address of the DNS Server which will be used to resolve hostname into IP Addresses .

UDP Port Number of DNS Service on the Server.

The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.

The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.

The altitude of the unit, measured in meters. This object is set by the SNMP manager and has no internal function.

The compliance statement for the Cambium PTP MIB

The dfs object group.

The bridge object group.

The configuration object group.

The ethernet object group.

The tDM object group.

The license object group.

The management object group.

The phyControl object group.

The phyStatus object group.

The alarms object group.

The apc object group.

The smtp object group.

The snmpControl object group.

The sntp object group.

The reset object group.

The versions object group.

The pubStats object group.

The encryption object group.

The tDDControl object group.

The syslogControl object group.

The aAAControl object group.

The routerProtocols object group.

The cableDiagnostics object group.

The unitIdentification object group.

The authorizationControl object group.

The dNS object group.

The supplementary object group.

The notifications group.

The PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detected, or ii) Dynamic Spectrum Optimization, (DSO) DSO improves link performance by selecting the most appropriate transmit and receive channels with the lowest level of interference.

DFS impulsive interference detected event

Current status of the Main PSU Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert

The SNMP ifAdminStatus of the interface has disabled Ethernet traffic

The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch

Current status of the Aux Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert

The SNMP ifAdminStatus of the interface has disabled Ethernet traffic

The Regulatory Band prohibits the wireless unit from operating outside the regulated limits. An invalid Regulatory Band may be caused by a missing or incorrect License Key, a corrupt MAC Address or an attempt to configure a Regulatory Band not allowed by the License Key or an execution of Reset Configuration. NB: a change of state may generate an SNMP trap and/or SMTP email alert.

A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert

Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert

The unit is out of calibration

Current status of the Power Over Ethernet (PoE) output of the Aux port

The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys

Spectrum Management was unable to locate a suitable wireless channel to operate on

The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic

The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.

If the SFP link is not OK, there are five possible causes: Either a SFP has been installed but the license key does not include SFP fiber support, a fiber link could not be established even though no LOS was detected (i.e. an optical carrier was detected, which could be due to a broken TX fiber, or because the link is disabled at the fiber link partner), a fiber link could not be established and LOS is detected (i.e. no optical carrier is detected), the installed SFP is not supported or the installed SFP failed to initialize correctly. NB: a change of status may generate an SNMP trap and/or SMTP email alert

Current status of the SFP Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert

A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions, or have different TDD Frame Configuraton Modes (Standard/Expert) in HCMP topology. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert

If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP

Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.

The SNMP ifAdminStatus of the interface has disabled Ethernet traffic

The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. This alarm is only raised if an Out-of-Band Management Mode has been configured.

The remote node of this link has been configured with a different link mode optimization

@Current status of the connection to the TDM Box. A state of 'Up' on a green background indicates that the TDM Box is connected OK. When connecting a TDM Box only the Main Ethernet port should be used

Current status of the TDM channels. A value of 0 indicates that a TDM channel is established

The loopback status of TDM channels. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. NB: a change of state may generate an SNMP trap and/or SMTP email alert

Current status of the NIDU LAN Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert

The syslog service has been enabled or disabled

The syslog local log is nearly full (90%)

The syslog local log has wrapped

Enable or disable the syslog client

The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, and one or more of the following security materials has not been configured: Key Of Keys, Private Key, Public Certificate, DRNG Entropy Status, Wireless Encryption Key. The secure mode mode is configured but not active(2) state indicates that the unit is capable of secure mode operation, and the security material has been configured, but the configuration of interfaces is not consistent with secure mode operation. The secure mode is not supported(3) state indicates that the unit is not capable of secure mode operation. The secure mode capability requires appropriate hardware compatibility, license key and software image.

Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode

If the full capability trial license period is about to expire then purchase a license upgrade from your reseller.

The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity.

The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This alarm is only raised if the license specifies a maximum link range and the trial license is not active.

Current status of the configuration of the TDM Box. A state of 'Ok' on a green background indicates that the TDM Box configuration is matched OK with the remote end.

The SNMP ifAdminStatus of the interface has disabled Ethernet traffic

The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch.

The local and remote ODUs have different services configured.

Current status of the wireless link. A state of Up on a green background indicates that a wireless link is established

Listen-Before-Talk (LBT) detected event

Alarm condition indicates that the unit's license is not secure enough for FIPS approved mode.