CAMBIUM-PTP500-MIB: View SNMP OID List / Download MIB

MIB for 105Mbps non-line-of-sight (NLOS) wireless ethernet bridge.

Number of entries in the dfsTable

A table storing a snapshot of various DFS measurements for each channel

Table DfsTable

used to index values in the dfsTable.

Snapshot of DFS means

Snapshot of DFS 99.9 percentiles

Snapshot of DFS peaks

Internet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is required to activate changes to this attribute.

A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance. NB: A system reboot is required to activate changes to this attribute

The IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to other networks. NB: A system reboot is required to activate changes to this attribute

MAC address of the PTP wireless unit forming the other end of the PTP link

The PTP wireless link operates using a master and slave relationship Enumeration: 'slave': 1, 'master': 0.

Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link

Antenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna.

Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna.

Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm

This control sets the bandwidth of the transmit and receive radio channels Enumeration: 'bw30MHz': 0, 'bw15MHz': 1, 'bw10MHz': 2, 'bw5MHz': 3, 'bw20MHz': 4.

IP Address of the peer wireless unit

Name of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link.

This field contains a user-provided description of the site name together with any additional notes

This controls whether the link can be established between pre-paired Master-Slave using MAC addresses (Link Access) or by using link name (Link Name Access) Enumeration: 'groupAccess': 2, 'linkAccess': 0, 'linkNameAccess': 1.

When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group. Group Access is only supported on some platforms

This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot. Enumeration: 'disabled': 0, 'enabled': 1.

This sets the different Ethernet configurations that will be advertised during auto negotiation. NB: The new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for! Bits: 'neg10MbpsHalfDuplex': 3, 'neg100MbpsHalfDuplex': 5, 'neg10MbpsFullDuplex': 4, 'neg100MbpsFullDuplex': 6, 'negUnknown1': 7, 'negInvalid': 2.

This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot Enumeration: 'disabled': 0, 'enabled': 1.

Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'down': 0, 'copperLinkUp': 1, 'fiberLinkUp': 2.

The current speed and duplex of the Ethernet link Enumeration: 'speedUnknown6': 5, 'speed1000MbpsFullDuplex': 0, 'speed100MbpsFullDuplex': 1, 'speed10MbpsFullDuplex': 3, 'speed100MbpsHalfDuplex': 2, 'speed10MbpsHalfDuplex': 4.

When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem. Enumeration: 'disabled': 0, 'enabled': 1.

This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot Enumeration: 'iEEE8021adTaggedSTagorBTagType88a8': 2, 'noVLANTagging': 0, 'iEEE8021QTaggedCTagType8100': 1.

This VLAN Priority (0-7) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot

This VLAN VID (0-4094) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot

Number of entries in the vLANPriorityTable.

A priority queue mapping table. This is a list of packet queues indexed by VLAN priority.

Table VLANPriorityTable

Mapping of VLAN priority flag to packet queue. The higher the queue number the greater its priority. Enumeration: 'q1': 1, 'q0': 0, 'q3': 3, 'q2': 2, 'q5': 5, 'q4': 4, 'q7': 7, 'q6': 6.

VLAN priority flag, used to index values in the vLANPriorityTable. Enumeration: 'p2': 3, 'p3': 4, 'p0': 1, 'p1': 2, 'p6': 7, 'p7': 8, 'p4': 5, 'p5': 6, 'untagged': 9.

The line interface type. If this is set to 'None' then the telecoms interfaces are disabled, and the telecom group attributes will be ignored. Enumeration: 'none': 0, 'e1': 1, 't1': 2.

Current status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'remoteTiming': 5, 'noSignalRemote': 2, 'up': 4, 'disabled': 0, 'noSignalLocalandRemoteTiming': 6, 'noSignalLocalandRemote': 3, 'noSignalLocal': 1.

The line code setting of the telecoms interface. This must match the setting of the device connected to this interface Enumeration: 'aMI': 0, 'b8ZSHDB3': 1.

The length of the cable connected to the telecoms interface, measured in feet Enumeration: 'feet133': 0, 'feet399': 2, 'feet655': 4, 'feet533': 3, 'feet266': 1.

The loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. When applying a wireless loopback, please ensure that the other end of the link has a loopback setting of 'None'. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'wireless': 2, 'copper': 1, 'none': 0.

The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'regionCode25': 25, 'regionCode24': 24, 'regionCode27': 27, 'regionCode26': 26, 'regionCode21': 21, 'regionCode20': 20, 'regionCode23': 23, 'regionCode22': 22, 'regionCode29': 29, 'regionCode28': 28, 'regionCode8': 8, 'regionCode9': 9, 'regionCode2': 2, 'regionCode3': 3, 'regionCode1': 1, 'regionCode6': 6, 'regionCode7': 7, 'regionCode4': 4, 'regionCode5': 5, 'regionCode30': 30, 'regionCode31': 31, 'regionCodeInvalid': 0, 'regionCode18': 18, 'regionCode19': 19, 'regionCode14': 14, 'regionCode15': 15, 'regionCode16': 16, 'regionCode17': 17, 'regionCode10': 10, 'regionCode11': 11, 'regionCode12': 12, 'regionCode13': 13.

The product variant Enumeration: 'spare5': 13, 'pTPxx500': 10, 'pTPxx400Deprecated1': 1, 'spare1': 4, 'spare3': 7, 'spare2': 6, 'pTPxx400Deprecated2': 2, 'pTPxx600Full': 12, 'pTPxx600Lite': 11, 'pTPxx400Full': 0, 'spare6': 14, 'pTPxx400Lite': 3, 'pTPxx500FullDeprecated': 8, 'pTPxx300': 5, 'pTPxx500LiteDeprecated': 9, 'pTP800': 15.

Name of the product variant

Ethernet fiber support availability on this wireless unit Enumeration: 'disabled': 0, 'enabled': 1.

Frequency variant of the wireless unit Enumeration: 'freq5900MHz': 7, 'freq4500MHz': 6, 'freq5800MHz': 0, 'freq5800MHz2': 4, 'freq5200MHz': 8, 'freq5400MHz2': 5, 'freq2500MHz': 3, 'freq4900MHz': 2, 'freq5400MHz': 1, 'freq5100MHz': 9, 'freq4800MHz': 10.

Bandwidth variant of the wireless unit Enumeration: 'bw30MHz': 0, 'bw15MHz': 1, 'bw10MHz': 2, 'bw5MHz': 3, 'bw20MHz': 4.

Constant power spectral density mode control Enumeration: 'fullPower': 1, 'constant': 0.

SNMPv3 availability control Enumeration: 'disabled': 0, 'enabled': 1.

Maximum allowable data rate for ethernet frames permitted by the licence key. The actual data rate depends upon the prevailing wireless conditions Enumeration: 'capacity105Mbps': 2, 'capacity52Mbps': 1, 'capacity25Mbps': 0.

A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert Enumeration: 'wrongPeer': 1, 'ok': 0.

Indicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or SMTP email alert Enumeration: 'armed': 1, 'disarmed': 0.

IP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved

The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved

Filename of the Software Upgrade to be loaded from the TFTP Server

Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished

The current status of the TFTP Software upgrade process Enumeration: 'upgradesuccessfulreboottorunthenewsoftwareimage': 3, 'idle': 0, 'uploadsuccessfulprogrammingFLASH': 2, 'upgradefailed': 4, 'uploadinprogress': 1.

Descriptive text describing the status of the TFTP Software upgrade process, including any error details

Any additional text describing the status of the TFTP Software upgrade process, including any error details

This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled) Enumeration: 'yes': 1, 'no': 0.

This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled) Enumeration: 'yes': 1, 'no': 0.

This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80)

This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the Licence Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443)

This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23)

This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled) Enumeration: 'yes': 1, 'no': 0.

In fixed asymmetric mode (3 to 1) the transmit time is three times as long as the receive time. In fixed symmetric mode (1 to 1) the unit spends an equal amount of time transmitting and receiving. In fixed asymmetric mode (1 to 3) the receive time is three times as long as the transmit time. In adaptive mode the transmit and receive periods adjust with applied load. NB: only applicable for master nodes. Enumeration: 'symmetry3to1': 1, 'symmetryAdaptive': 0, 'symmetry1to1': 2, 'symmetry1to3': 3.

Optimises the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimise transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimise transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols. Enumeration: 'tDMTraffic': 1, 'iPTraffic': 0.

The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard Enumeration: 'mod64qam83percent': 6, 'modQpsk50percent': 1, 'mod16qam50percent': 3, 'modQpsk75percent': 2, 'mod16qam75percent': 4, 'mod64qam67percent': 5, 'modBpsk50percent': 0.

Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link

Receive power expressed in tenths of a dBm

The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dB

Transmit power expressed in tenths of a dBm

Distance between the two peer wireless units expressed in tenths of a kilometer

The wireless link loss expressed in tenths of a dB

Current active receive channel

Current active transmit channel

Current active receive modulation mode Enumeration: 'mod16qam75percentSingle': 5, 'mod16qam75percentDual': 12, 'mod16qam50percentDual': 11, 'modQpsk75percentSingle': 3, 'modQpsk75percentDual': 10, 'modReserved1': 8, 'modReserved2': 15, 'modAcquisition': 0, 'mod64qam67percentSingle': 6, 'mod16qam50percentSingle': 4, 'modBpsk50percent': 1, 'modQpsk50percentSingle': 2, 'mod64qam67percentDual': 13, 'mod64qam83percentSingle': 7, 'mod64qam83percentDual': 14, 'modQpsk50percentDual': 9.

Current active transmit modulation mode Enumeration: 'mod16qam75percentSingle': 5, 'mod16qam75percentDual': 12, 'mod16qam50percentDual': 11, 'modQpsk75percentSingle': 3, 'modQpsk75percentDual': 10, 'modReserved1': 8, 'modReserved2': 15, 'modAcquisition': 0, 'mod64qam67percentSingle': 6, 'mod16qam50percentSingle': 4, 'modBpsk50percent': 1, 'modQpsk50percentSingle': 2, 'mod64qam67percentDual': 13, 'mod64qam83percentSingle': 7, 'mod64qam83percentDual': 14, 'modQpsk50percentDual': 9.

Current receive frequency expressed in integer MHz

Current transmit frequency expressed in integer MHz

Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dB

Current receive frequency expressed as KHz

Current transmit frequency expressed as KHz

Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal. Enumeration: 'acquiring': 2, 'searching': 1, 'registering': 0, 'registeringAcquiring2': 3.

The unit is out of calibration Enumeration: 'bandwidthvariantunsupportedPAsShutdown': 3, 'outOfCalibrationPAsShutdown': 4, 'calibrated': 0, 'invalidCalibration': 2, 'partialCalibration': 1.

The master and slave units have incompatible region codes. NB: Both units must have compatible licence keys Enumeration: 'incompatibleLicenceKeys': 1, 'ok': 0.

Spectrum Management was unable to locate a suitable wireless channel to operate on Enumeration: 'noWirelessChannelAvailable': 1, 'ok': 0.

The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic Enumeration: 'disabledBySNMPifAdminStatus': 1, 'ok': 0.

The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic Enumeration: 'disabledBySNMPifAdminStatus': 1, 'ok': 0.

The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch Enumeration: 'noError': 0, 'mismatchDetected': 1.

A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert Enumeration: 'differentSoftwareVersionsRunning': 2, 'incompatibleProductVariants': 1, 'ok': 0.

An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference. Enumeration: 'holdoverNotConnected': 2, 'noTimingReference': 4, 'locked': 0, 'tDDSyncNotActive': 8, 'timingSystemNotConnected': 5, 'holdover': 1, 'initialising': 6, 'acquiringLock': 3, 'clusterTimingMaster': 7.

Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired. Enumeration: 'notSynchronized': 1, 'ok': 0, 'timingSystemFailure': 2.

The remote node of this link has been configured with a different link mode optimization Enumeration: 'ok': 0, 'linkModeOptimizationMismatch': 1.

The local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating at the capacity of the lowest capacity unit Enumeration: 'ok': 0, 'mismatchDetected': 1.

Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address. This utility can only be configured by the system administrator Enumeration: 'disabled': 0, 'enabled': 1.

IP address of the SMTP server

Port number of the SMTP server

The 'from' email address used when constructing the automatically generated e-mail message

The 'to' email address used when constructing the automatically generated e-mail message

This controls which SMTP messages the unit will send Bits: 'wirelessLinkUpDown': 7, 'dFSImpulseInterference': 5, 'unknown6': 2, 'channelChange': 6, 'telecomsChannelUpDown': 1, 'enabledDiagnosticAlarms': 4, 'dataPortUpDown': 3.

The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute

The SNMP community string. NB: A system reboot is required to activate changes to this attribute

Number of entries in the sNMPTrapTable.

SNMP trap configuration table.

Table SNMPTrapTable

SNMP trap value, used to index the SNMPTrapTable.

The IP address to which all SNMP Traps are sent. An IP Address of 0.0.0.0 disables all TRAP generation. NB: A system reboot is required to activate changes to this attribute.

Destination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver. NB: A system reboot is required to activate changes to this attribute.

The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute Enumeration: 'v2c': 1, 'v1': 0.

This controls which SNMP Traps the unit will send Bits: 'wirelessLinkUpDown': 6, 'dFSImpulseInterference': 4, 'authenticationFailure': 2, 'dataPortUpDown': 1, 'channelChange': 5, 'telecomsChannelUpDown': 15, 'unknown8': 0, 'enabledDiagnosticAlarms': 3, 'coldStart': 7.

Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributes Bits: 'tDDSynchronizationAlarm': 22, 'installStatus': 6, 'sNTPSynchronizationFailed': 13, 'telecomsChannelStatus': 8, 'incompatibleRegionCodes': 1, 'syslogClientDisabledWarning': 16, 'linkModeOptimizationMismatch': 21, 'dataPortConfigurationMismatch': 15, 'incompatibleMasterAndSlave': 0, 'wirelessLinkDisabledWarning': 12, 'dataPortDisabledWarning': 11, 'regionCode': 7, 'unitOutOfCalibration': 4, 'unknown6': 2, 'syslogLocalWrapped': 18, 'unknown5': 3, 'unknown15': 9, 'syslogLocalNearlyFull': 19, 'noWirelessChannelAvailable': 14, 'installArmState': 5, 'licensedCapacityMismatch': 17, 'dataPortStatus': 10, 'syslogLocalEnableDisable': 20, 'telecomsChannelLoopback': 23.

Controls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient events (i.e. not associated with an alarm or status value) are only sent when required and not at start-up. Enumeration: 'disabled': 0, 'enabled': 1.

SNTP control state Enumeration: 'disabled': 0, 'enabled': 1.

The IP address of a valid SNTP server

The IP port number of the SNTP server. Defaults to port 123.

The SNTP server polling interval

If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP email alert Enumeration: 'inSync': 1, 'noSync': 0.

Last SNTP sync time

System clock presented as local time

Time zone offsets from Greenwich Mean Time (GMT) Enumeration: 'gmtPlus1030': 45, 'gmtMinus0900': 6, 'gmtPlus0300': 30, 'gmtPlus1130': 47, 'gmtMinus0800': 8, 'gmtMinus0100': 22, 'gmtZero': 24, 'gmtPlus1300': 50, 'gmtPlus0430': 33, 'gmtPlus0800': 40, 'gmtPlus0030': 25, 'gmtMinus0330': 17, 'gmtMinus1000': 4, 'gmtPlus0900': 42, 'gmtMinus0700': 10, 'gmtPlus0700': 38, 'gmtPlus0630': 37, 'gmtMinus1100': 2, 'gmtMinus0600': 12, 'gmtMinus0230': 19, 'gmtPlus0930': 43, 'gmtMinus0500': 14, 'gmtPlus0530': 35, 'gmtMinus0400': 16, 'gmtPlus0600': 36, 'gmtPlus0330': 31, 'gmtMinus0830': 7, 'gmtPlus1000': 44, 'gmtPlus1230': 49, 'gmtMinus0930': 5, 'gmtMinus1200': 0, 'gmtPlus0100': 26, 'gmtPlus0400': 32, 'gmtPlus1100': 46, 'gmtMinus0130': 21, 'gmtPlus0500': 34, 'gmtMinus1030': 3, 'gmtPlus0230': 29, 'gmtMinus0730': 9, 'gmtMinus0300': 18, 'gmtPlus0830': 41, 'gmtMinus0030': 23, 'gmtMinus0200': 20, 'gmtPlus0130': 27, 'gmtPlus0730': 39, 'gmtMinus1130': 1, 'gmtMinus0630': 11, 'gmtPlus1200': 48, 'gmtMinus0430': 15, 'gmtMinus0530': 13, 'gmtPlus0200': 28.

Daylight Saving Time Enumeration: 'disabled': 0, 'enabled': 1.

Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory Enumeration: 'consoleReboot': 1, 'running': 0.

Current software version

Hardware platform version

Secondary software version, used when the primary software image is invalid or erased

Boot code software version

Average data rate over the last one second interval (kbps)

Average data rate over the last one second interval (kbps)

Average data rate over the last one second interval (kbps)

Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision

Current status of the wireless link Enumeration: 'acquiring': 2, 'registering': 1, 'up': 0, 'searching': 3, 'initialising': 5, 'radarCAC': 4.

Reciprocal of the byte error ratio calculated since the last reset of the system counters

The reason for the current receive modulation mode Enumeration: 'runningAtMaximumReceiveModeForChannelBandwidth': 7, 'restrictedBecauseTheLinkParametersAreUpdating': 4, 'runningAtUserConfiguredMaxModulationMode': 1, 'runningAtMaximumReceiveMode': 0, 'restrictedBecauseChannelChangeIsInProgress': 5, 'restrictedBecauseOfByteErrorsOnTheWirelessLink': 3, 'limitedByTheWirelessConditions': 8, 'restrictedBecauseInstallationIsArmed': 2, 'restrictedDueToTheLowEthernetLinkSpeed': 6.

The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctly Enumeration: 'aES256bitRijndael': 2, 'none': 0, 'aESRijndael': 1.

TDD Synchronization Mode selection Enumeration: 'disabled': 0, 'enabled': 1.

Enable or disable the syslog client Enumeration: 'disabled': 0, 'enabled': 1.

The syslog service has been enabled or disabled Enumeration: 'disabled': 0, 'enabled': 1.

Number of entries in the userTable

The User Table Control group contains objects specifically for user account management.

Table UserTable

used to index values in the userTable.

User name which must be entered, along with the appropriate password, in order to gain access to the system.

Role of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security settings. A Read Only user can view settings, but cannot make any changes. Enumeration: 'systemAdministrator': 1, 'readOnly': 0, 'securityOfficer': 2.

Enable / Disable the selected user Enumeration: 'disabled': 0, 'enabled': 1.

User password, which must be entered in order to gain access to the system.

The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.

The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.

The altitude of the unit, measured in metres. This object is set by the SNMP manager and has no internal function.

The compliance statement for the Cambium PTP MIB

The dfs object group.

The configuration object group.

The ethernet object group.

The telecom object group.

The licence object group.

The management object group.

The phyControl object group.

The phyStatus object group.

The alarms object group.

The smtp object group.

The snmpControl object group.

The sntp object group.

The reset object group.

The versions object group.

The pubStats object group.

The encryption object group.

The tDDControl object group.

The syslogControl object group.

The aAAControl object group.

The supplementary object group.

The notifications group.

The PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detected, or ii) Dynamic Spectrum Optimization, (DSO) DSO improves link performance by selecting the most appropriate transmit and receive channels with the lowest level of interference.

DFS impulsive interference detected event

Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert

Current status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert

The loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. When applying a wireless loopback, please ensure that the other end of the link has a loopback setting of 'None'. NB: a change of state may generate an SNMP trap and/or SMTP email alert

The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change of state may generate an SNMP trap and/or SMTP email alert

A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert

Indicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or SMTP email alert

The unit is out of calibration

The master and slave units have incompatible region codes. NB: Both units must have compatible licence keys

Spectrum Management was unable to locate a suitable wireless channel to operate on

The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic

The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic

The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch

A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert

If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP email alert

Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.

The remote node of this link has been configured with a different link mode optimization

The local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating at the capacity of the lowest capacity unit

The syslog service has been enabled or disabled

The syslog local log is nearly full (90%)

The syslog local log has wrapped

Enable or disable the syslog client