CADANT-REMOTE-QUERY-MIB: View SNMP OID List / Download MIB

VENDOR: CADANT INC.


 Home MIB: CADANT-REMOTE-QUERY-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, CADANT-CMTS-MAC-MIB, INET-ADDRESS-MIB, DOCS-IF-MIB, CADANT-PRODUCTS-MIB, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 cadCmRemoteQueryMib 1.3.6.1.4.1.4998.1.1.55.1
This MIB module provides the management of the Cadant C4 Cable Modem Termination Systems (CMTS) Remote Query feature. This feature, implemented on a CMTS, facilitates SNMP polling of remote cable modems (CMs). This MIB includes the configuration and status objects of the CMTS CM Poller and remote CMs that polled by the CMTS CM Poller
     cadCmRemoteQueryPoller 1.3.6.1.4.1.4998.1.1.55.1.1
         cadCmRemoteQueryPollerEnable 1.3.6.1.4.1.4998.1.1.55.1.1.1 truthvalue read-write
An indication of whether the CMTS CM Poller is running. When the poller is enabled, it polls the remote CMs periodically specified in the cadCmRemoteQueryPollerInterval mib object. The operation can be expensive depending on how many CMs that the poller would be polling. It is suggested to have it disabled when not needed.
         cadCmRemoteQueryPollerInterval 1.3.6.1.4.1.4998.1.1.55.1.1.2 unsigned32 read-write
An interval between two polling cycles of the CMTS CM Poller. The poller will not start the next cycle until it finished polling for the last CM , even though the time has expired. If the cadCmRemoteQueryPollerInterval is too small with a large number of CMs, the poller would tie up the CPU and resources and possibly degrade the system's performance.
         cadCmRemoteQueryPollerStartTime 1.3.6.1.4.1.4998.1.1.55.1.1.3 unsigned32 read-only
The value of sysUpTime in seconds when the last polling cycle started. cadCmRemoteQueryPollerStartTime is set to 0 when the CMTS is first restarted and doesn't get reset after the poller is disabled.
         cadCmRemoteQueryPollerStopTime 1.3.6.1.4.1.4998.1.1.55.1.1.4 unsigned32 read-only
The value of sysUpTime in seconds when the last polling cycle finished. cadCmRemoteQueryPollerStopTime is set to 0 when the CMTS is first restarted and doesn't get reset after the poller is disabled.
         cadCmRemoteQueryPollerCommunity 1.3.6.1.4.1.4998.1.1.55.1.1.5 octet string read-write
The read community string is used for polling the CMs. Any change in the cadCmRemoteQueryPollerCommunity may not be reflected if the poller has already been enabled.
         cadCmRemoteQueryMacAddress 1.3.6.1.4.1.4998.1.1.55.1.1.6 macaddress read-write
The object is used to trigger an immediate poll of a specific CM. This object always read back as a value of 0. The value of sysUpTime should be read and saved before writing this object. Then, the value of cadCmRemoteQueryPollTime can be read and compared to the saved sysUpTime to determine when the immediate poll of retmoe query data has been completed.
         cadCmRemoteQuerySourceIpAddrType 1.3.6.1.4.1.4998.1.1.55.1.1.7 inetaddresstype read-only
The type of internet address of cadCmRemoteQuerySourceIpAddr.
         cadCmRemoteQuerySourceIpAddr 1.3.6.1.4.1.4998.1.1.55.1.1.8 inetaddress read-only
The source IP address of the SNMP remote queries to the CMs. This value is changed from the Poller when the ifIndex of the cadSysSourceInterfaceRemoteQuery in the CADANT-CMTS-SYSTEM-MIB is changed due to using the cli command .. configure cable modem remote-query source-interface ..
     cadCmRemoteQueryStatusTable 1.3.6.1.4.1.4998.1.1.55.1.2 no-access
This table contains the status of the cable modems that are polled by the CMTS CM Poller. The information will be overwritten when a new polling cycle starts. Depending on how many CMs that the poller is polling, polling this table constantly can be quite expensive; Excessive polling could degrade performance.
         cadCmRemoteQueryStatusEntry 1.3.6.1.4.1.4998.1.1.55.1.2.1 no-access
A list of the cable modem's attributes that are polled by a CMTS.
             cadCmRemoteQueryPollTime 1.3.6.1.4.1.4998.1.1.55.1.2.1.1 unsigned32 read-only
The value of sysUpTime when this CM entry was polled. If this value is larger than the cadCmRemoteQueryPollerStopTime, it indicates that the status has already been overwritten by a new polling cycle. To avoid this happening, the NMS can increase the cadCmRemoteQueryPollInterval so that the cadCmRemoteQueryPollTime would fall in between the cadCmRemoteQueryPollerStartTime and the cadCmRemoteQueryPollerStopTime.
             cadCmRemoteQueryDownChannelPower 1.3.6.1.4.1.4998.1.1.55.1.2.1.2 tenthdbmv read-only
The CM's received power level. This object may be set to zero if the CM does not support power level measurement. If the CM downstream interface is down, this object either returns the most current value or the value of 0.
             cadCmRemoteQueryStatusTxPower 1.3.6.1.4.1.4998.1.1.55.1.2.1.3 tenthdbmv read-only
The operational transmit power for the CM upstream channel.
             cadCmRemoteQueryUpChnlTxTimingOffset 1.3.6.1.4.1.4998.1.1.55.1.2.1.4 unsigned32 read-only
A measure of the current round trip time. Used for timing of CM upstream transmissions to ensure synchronized arrivals at the CMTS.
             cadCmRemoteQuerySigQSignalNoise 1.3.6.1.4.1.4998.1.1.55.1.2.1.5 tenthdb read-only
Signal/Noise ratio as perceived for the CM downstream channel.
             cadCmRemoteQuerySigQMicroreflections 1.3.6.1.4.1.4998.1.1.55.1.2.1.6 integer32 read-only
Total microreflections including in-channel response as perceived on the CM downstream, measured in dBc below the signal level. This object is not assumed to return an absolutely accurate value, but is meant to give a rough indication of microreflections received on this interface. It is up to the implementor to provide information as accurate as possible.
             cadCmRemoteQuerySysDescr 1.3.6.1.4.1.4998.1.1.55.1.2.1.7 displaystring read-only
A textual description of the entity.
     cadCmRemoteQueryConformance 1.3.6.1.4.1.4998.1.1.55.1.3
         cadCmRemoteQueryDocsRemoteQueryCompliances 1.3.6.1.4.1.4998.1.1.55.1.3.1
             cadCmRemoteQueryDocsRemoteQueryCompliance 1.3.6.1.4.1.4998.1.1.55.1.3.1.1
The compliance statement for entities which implement the Remote Query MIB
         cadCmRemoteQueryDocsRemoteQueryGroups 1.3.6.1.4.1.4998.1.1.55.1.3.2
             cadCmRemoteQueryPollerGroup 1.3.6.1.4.1.4998.1.1.55.1.3.2.1
Group of objects implemented in Cable Modem Termination Systems (CMTS) for configuring and monitoring the CMTS CM Poller.
             cadCmRemoteQueryStatusGroup 1.3.6.1.4.1.4998.1.1.55.1.3.2.2
Group of objects implemented in Cable Modem Termination Systems (CMTS) for monitoring cable modems via CMTS CM Poller.