A3COM-MIP-R1-MIB: View SNMP OID List / Download MIB

VENDOR: 3COM


 Home MIB: A3COM-MIP-R1-MIB
Download as:   
SNMPv2-CONF, SNMPv2-SMI, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 a3Com 1.3.6.1.4.1.43
       brouterMIB 1.3.6.1.4.1.43.2
           a3ComMIP 1.3.6.1.4.1.43.2.27
                 a3ComMipSConfig 1.3.6.1.4.1.43.2.27.1
                     a3ComMipControl 1.3.6.1.4.1.43.2.27.1.1 integer read-write
If this object is set to enabled(1), then multicast IP routing is in service. If it is set to disabled(2), then multicast IP routing is turned off. Enumeration: 'disabled': 2, 'enabled': 1.
                 a3ComMipCConfig 1.3.6.1.4.1.43.2.27.2
                     a3ComMipPortTable 1.3.6.1.4.1.43.2.27.2.1 no-access
This table contains entries of parameters associated with every port or tunnel.
                         a3ComMipPortEntry 1.3.6.1.4.1.43.2.27.2.1.1 no-access
Each entry contains information for a spcified port or tunnel.
                             a3ComMipPortIndex 1.3.6.1.4.1.43.2.27.2.1.1.1 integer read-only
The port number or tunnel ID of which this entry applies. The tunnel ID starts with 1025 and end with 1056, i.e. total tunnel number is limited to 32.
                             a3ComMipPortQueryInterval 1.3.6.1.4.1.43.2.27.2.1.1.2 integer read-write
This object specifies the time interval in seconds that a Host Query message is sent to the attached subnet to request for the local group membership. It also derives the Membership Expiration time which is set to two times value of this object plus 20 seconds. This object cannot be applied on tunnel port.
                             a3ComMipPortThreshold 1.3.6.1.4.1.43.2.27.2.1.1.3 integer read-write
This object specifies the minimum IP TTL required for a multicast datagram to be forwarded to the given port or tunnel.
                             a3ComMipPortQuerier 1.3.6.1.4.1.43.2.27.2.1.1.4 integer read-only
This object specifies if the system is responsible for sending out Host Query messages on this port. If the value is yes(1) then the system is the designated router on the subnet this port connects to and the system is sending out Host Query messages periodically on that port. This object must be set to value no(2) for tunnel port. Enumeration: 'yes': 1, 'no': 2.
                             a3ComMipPortPaceMode 1.3.6.1.4.1.43.2.27.2.1.1.5 integer read-write
This object is used to control PACE mode. If set to enabled(1), the multicast packets will be sent out with the Universal/Local bit set, or Priority MAC. If set to disabled(2) the Universal/Local bit is clear, or Interactive MAC. Enumeration: 'disabled': 2, 'enabled': 1.
                     a3ComMipLocalGroupTable 1.3.6.1.4.1.43.2.27.2.2 no-access
This table contains group membership information of each attached subnet.
                         a3ComMipLocalGroupEntry 1.3.6.1.4.1.43.2.27.2.2.1 no-access
Each entry contains a group membership information associated with a specific port.
                             a3ComMipLocalGroupPort 1.3.6.1.4.1.43.2.27.2.2.1.1 integer read-only
This object specifies the port number to which this entry applies.
                             a3ComMipLocalGroupIpAddr 1.3.6.1.4.1.43.2.27.2.2.1.2 ipaddress read-only
This object specifies group's address presents on the specified port. If the port is configured as a tunnel, there will be no group address associated with it.
                             a3ComMipLocalGroupType 1.3.6.1.4.1.43.2.27.2.2.1.3 integer read-only
This object specifies the type of local group. This object can only be set to 'static' by SET command, and if the local group is learned from IGMP, it is set to 'igmp'. Enumeration: 'static': 1, 'igmp': 2.
                             a3ComMipLocalGroupStatus 1.3.6.1.4.1.43.2.27.2.2.1.4 rowstatus read-write
This object is used to add and delete entries in this table. See the definition of RowStatus for detail.
                     a3ComMipSmdsGroupTable 1.3.6.1.4.1.43.2.27.2.3 no-access
This table contains a set of IP network address and SMDS group address mapping.
                         a3ComMipSmdsGroupEntry 1.3.6.1.4.1.43.2.27.2.3.1 no-access
Each entry contains an IP network address to SMDS group address mapping.
                             a3ComMipSmdsGroupIpAddr 1.3.6.1.4.1.43.2.27.2.3.1.1 ipaddress read-only
This is an IP network address for which there is a corresponding SMDS group address.
                             a3ComMipSmdsGroupMediaAddr 1.3.6.1.4.1.43.2.27.2.3.1.2 octet string read-write
This is the SMDS group address that corresponds to the IP network address identified by a3ComMipSmdsGroupIpAddr.
                             a3ComMipSmdsGroupStatus 1.3.6.1.4.1.43.2.27.2.3.1.3 rowstatus read-write
This object is used to add and delete entries in this table. See the definition of RowStatus for detail.
                 a3ComMipData 1.3.6.1.4.1.43.2.27.3