ZYXEL-xs3900-48F-MIB: View SNMP OID List / Download MIB

SW platform major version, e.g. 3.

SW platform minor version, e.g. 50.

Model letters, e.g. TJ

Version control number, e.g. 0.

SW compilation day, e.g. 19.

SW compilation month, e.g. 8.

SW compilation year, e.g. 2004.

Serial number

Current system boot up image, You can change the boot up image of next rebooting by setting sysMgmtBootupImage.

Ingress/egress rate limiting enabled/disabled for the switch.

An entry in rateLimitPortTable.

Ingress/egress rate limiting enabled/disabled on the port.

Commit rate in Kbit/s. The range of FE port is between 0 and 100,000. For GE port, the range is between 0 and 1000,000.

Peak rate in Kbit/s. The range of FE port is between 1 and 100,000. For GE port, the range is between 1 and 1000,000.

Egress rate in Kbit/s. The range of FE port is between 1 and 100,000. For GE port, the range is between 1 and 1000,000.

Ingress peak rate limiting enabled/disabled on the port.

Egress rate limiting enabled/disabled on the port.

Ingress commit rate limiting enabled/disabled on the port.

Broadcast/multicast/DLF rate limiting enabled/disabled for the switch.

An entry in brLimitPortTable.

Broadcast rate limiting enabled/disabled on the port.

Allowed broadcast rate in pkts/s. For FE port, the maximum value is 148800. For GE port, the maximum value is 262143.

Multicast rate limiting enabled/disabled on the port.

AAllowed mullticast rate in pkts/s. For FE port, the maximum value is 148800. For GE port, the maximum value is 262143.

Destination lookup failure frames rate limiting enabled/disabled on the port.

Allowed destination lookup failure frames rate in pkts/s. For FE port, the maximum value is 148800. For GE port, the maximum value is 262143.

An entry in portSecurityPortTable.

Port Security enabled/disabled on the port. Active(1) means this port only accept frames from static MAC addresses that are configured for the port, and dynamic MAC address frames up to the number specified by portSecurityPortCount object.

MAC address learning enabled/disable on the port.

Number of (dynamic) MAC addresses that may be learned on the port.

This entry is used to execute MacFreeze action to port. Its meaningless while reading this entry.

An entry in portSecurityVMLTable.

The configured port number of VLAN MAC Limit.

The configured VLAN number of VLAN MAC Limit.

The MAC limit of specific port and VLAN.

An entry in vlanTrunkPortTable.

VlanTrunking enabled/disabled on the port. Active(1) to allow frames belonging to unknown VLAN groups to pass through the switch.

Bridge control protocol transparency enabled/disabled for the switch

An entry in ctlProtTransTunnelPortTable.

Bridge control protocol transparency mode for the port. Modes: Peer(0), Tunnel(1), Discard(2), Network(3)

VLAN Stacking enabled/disabled for the switch.

An entry in vlanStackPortTable.

Mode of the port. Set Normal to have the switch ignore frames received (or transmitted) on this port with VLAN stacking tags. Anything you configure in SPVID and Priority are ignored. Set Access mode to have the switch add the SP TPID tag to all incoming frames received on this port. Set Access mode for ingress ports at the edge of the service providers network. Set Tunnel mode (available for Gigabit ports only) for egress ports at the edge of the service providers network. In order to support VLAN stacking on a port, the port must be able to allow frames of 1526 Bytes (1522 Bytes + 4 Bytes for the second tag) to pass through it. normal (1), Access (2), tunnel (3)

VLAN ID used in service provider tag.

Priority value for service provider tag. 0 is the lowest priority level and 7 is the highest.

Tunnel Port TPID in hex format, e.g. 8100.

An entry in selective qinq table

The name of selective qinq entry

interface port id

inner vid

outer vid

priority

802.1x port authentication enabled/disabled for the switch.

An entry in portAuthTable.

802.1x port authentication enabled or disabled on the port.

802.1x port re-authentication enabled or disabled on the port.

Re-authentication timer in seconds.

Quiet period in seconds.

Tx period in seconds.

Supplicant Timeout in seconds.

Max request.

Guest Vlan State.

Guest Vlan ID.

Guest Vlan Host Mode.

Guest Vlan Host Mode Multi-Secure number.

An entry in fanRpmTable.

Index of FAN.

Current speed in Revolutions Per Minute (RPM) on the fan.

Maximum speed measured in Revolutions Per Minute (RPM) on the fan.

Minimum speed measured in Revolutions Per Minute (RPM) on the fan.

The minimum speed at which a normal fan should work.

Normal indicates that this fan is functioning above the minimum speed. Error indicates that this fan is functioning below the minimum speed.

An entry in tempTable.

Index of temperature unit. 1:MAC, 2:CPU, 3:PHY

The current temperature measured at this sensor.

The maximum temperature measured at this sensor.

The minimum temperature measured at this sensor.

The upper temperature limit at this sensor.

Normal indicates temperatures below the threshold and Error for those above.

An entry in voltageTable.

Index of voltage.

The current voltage reading.

The maximum voltage measured at this point.

The minimum voltage measured at this point.

The normal voltage at wchich the switch work.

The minimum voltage at which the switch should work.

Normal indicates that the voltage is within an acceptable operating range at this point; otherwise Error is displayed.

An entry in snmpTrapDestTable.

IP address of trap destination.

The UDP port of the trap destination.

The SNMP protocol version to send traps.

The user name for sending SNMPv3 traps.

The SNMP version to be used. v3v2c means that the manager can get/set by SNMPv3 and can get by SNMPv2c.

A table that contains SNMPv3 user information.

An entry of snmpUserTable.

The user name.

The level of security at which SNMP messages can be sent or with which operations are being processed.

The type of authentication protocol to be used.

The type of privacy protocol to be used.

The group name which this user belongs to.

The table cantains SNMP trap group configuration.

An entry cantains SNMP trap group configuration.

System group of SNMP trap that the switch sends to the SNMP manager.

The time service protocol.

IP address of time server.

The time difference between UTC. Ex: +01

The new date in year.

The new date in month.

The new date in day.

The new time in hour.

The new time in minute.

The new time in second.

Daylight saving time service enabled/disabled for the switch.

Daylight saving time service start week.

Daylight saving time service start day.

Daylight saving time service start month.

Daylight saving time service start time.

Daylight saving time service end week.

Daylight saving time service end day.

Daylight saving time service end month.

Daylight saving time service end time.

If setting value is given, the variable write index will be set and running-config will be written to the assigned configuration file. If not, running-config will be written to the booting one. Note: This action can access all configuration includes user account and AA configuration.

The setting value (read index) will be written into non-volatile memory. While rebooting, the variable write index is equal to read index initially. You can change the value of write index by CLI / MIB.

Reboot switch from SNMP. 1:Reboot, 0:Nothing

Erase running config and reset to default. Note: This action can access all configuration includes user account and AA configuration.

Display status of last mgmt action.

This variable indicates the status of the system. The sysMgmtAlarmStatus is a bit map represented a sum, therefore, it can represent multiple defects simultaneously. The sysNoDefect should be set if and only if no other flag is set. The various bit positions are: 0 sysAlarmDetected 1 sysTemperatureError 2 sysFanRPMError 3 sysVoltageRangeError

Show device CPU load in %, its the snapshot of CPU load when getting the values.

The setting value (read index) will be written into non-volatile memory. When rebooting, the selected image will be used. You can change the value of write index by CLI / MIB.

Reset all port counters.

IP address of TFTP server

The file name that you want to backup to or restore from TFTP server

Index of system configuration which you want to restore.

Action of tftp service. 1: Backup running-config to tftp server, 2: Restore config from tftp server, 3: Merge config from tftp server. Note: This action can access all configuration includes user account and AA configuration.

Display status of mgmt action.

Action of tftp service. 1: Backup running-config to tftp server, 2: Restore config from tftp server, 3: Merge config from tftp server. Note: This action can access configuration with privilege 13.

If setting value is given, the variable write index will be set and running-config will be written to the assigned configuration file. If not, running-config will be written to the booting one. Note: This action can access configuration with privilege 13.

Erase running config and reset to default. Note: This action can access configuration with privilege 13.

Specify host timeout for all multicast groups when the specific port is in auto mode.

Set the 802.1p priority of control messages for igmp-snooping(0~8, 8-No Change)

An entry in IgmpsnpVlanTable.

IGMP Snooping report-proxy mode

An entry in inbandIpTable.

An entry in filterTable.

An entry in mirrorTable.

An entry in aggrGroupTable.

An entry in aggrPortTable.

An entry in accessCtlTable.

An entry in securedClientTable.

An entry in portQueuingMethodTable.

0...7

0...15

unicast and nonunicast weights, range from 1 to 127

An entry in portQueuingMethodTable.

An entry in globalDhcpRelayRemoteServerTable.

The maximum number of DHCP server entries that can be created. A value of 0 for this object implies that there exists settings for global DHCP relay.

An entry in dhcpServerTable.

The maximum number of DHCP relay entries that can be created. A value of 0 for this object implies that there exists settings for global DHCP relay.

An entry in dhcpRelayRemoteServerTable.

An entry in dhcpRelayTable.

An entry in staticRouteTable.

An entry in arpTable.

An entry in portOpModePortTable.

This entry display latest loopback test status of port while performing loopback test.

This entry resets port counter.

The length of CX4 Cable.

Set the 10GBase media type.

An entry in portBasedVlanPortListTable.

An entry in multicastPortTable.

0..255

Specify throttling action for each port

200..6348800

200..6348800

An entry in multicastStatusTable.

An entry in multicastVlanStatusTable.

A count table of igmp query/report/leave message.

An entry in igmpSnpCountTable.

Index of IgmpCountEntry. 0 means total count in whole system

An entry in igmpGroupVlanStatus.

Input vlan

show igmpsnp Query Rx counters for vlan

show igmpsnp Report Rx counters for vlan

show igmpsnp Leave Rx counters for vlan

show igmpsnp Query Rx Error counters for vlan

show igmpsnp Report Rx Error counters for vlan

show igmpsnp Leave Rx Error counters for vlan

show igmpsnp Query Tx counters for vlan

show igmpsnp Report Tx counters for vlan

show igmpsnp Leave Tx counters for vlan

show igmpsnp Query Rx counters for vlan

show igmpsnp Report Rx counters for vlan

show igmpsnp Query Rx Error counters for vlan

show igmpsnp Report Rx Error counters for vlan

show igmpsnp Query Tx counters for vlan

show igmpsnp Report Tx counters for vlan

An entry in igmpSnpCountPortStatus.

show igmpsnp Query Rx counters for port

show igmpsnp Report Rx counters for port

show igmpsnp Leave Rx counters for port

show igmpsnp Report Rx Error counters for port

show igmpsnp Leave Rx Error counters for port

show igmpsnp Report Tx counters for port

show igmpsnp Leave Tx counters for port

show igmpsnp Query Rx counters for port

show igmpsnp Report Rx counters for port

show igmpsnp Report Rx Error counters for port

show igmpsnp Report Tx counters for port

Show total IGMP snooping group number

An entry in igmpSnpGroupVlanStatus.

Show IGMP snooping group index for vlan

Show IGMP snooping group number for vlan

An entry in igmpGroupCountPortStatus.

Show IGMP snooping group number for port

An entry in igmpFilteringProfileTable.

An entry in mvrTable.

1..4094

Set the 802.1p priority of control messages within MVR (0~7)

An entry in mvrPortTable.

An entry in mvrGroupTable.

An entry in clusterManagerTable.

An entry in clusterMemberTable.

An entry in clusterCandidateTable.

An entry in clusterStatusMemberTable.

A list of currently active fault events. All faults of normal type regardless of their severity level are recorded in the event table. When a normal type fault is cleared it is deleted from the event table.

An entry containing information about an event in the event table.

This variable represents the sequence number of an event. Sequence number is incremented monotonically starting from 0 until it reaches its maximum and wraps around back to 0. Sequence number is incremented when - the state of a normal type fault is set on (the same sequence number is present in the events table as well as in the trap that is sent to notify about the fault on event) - delta event occurs (sequence number present in trap message) - the state of a normal type fault is set off (sequence number present in trap that is sent to notify for clearing).

This variable represents the event ID which uniquely identifies the event in the entire system.

This variable represents the name of the event, for example Ethernet Link Down

This variable represents the type of InstanceId of a particular event in the event table. In brief the instanceType refers to the type of sub-component generating this event in the system, for example switch (5). For more details see the textual conventions section. AFFECTS: eventInstanceId, eventInstanceName

This variable represents the InstanceId of a particular event in the event current table. In brief the instanceId refers to the sub-component generating this event in the system, for example 1 for port 1. For more details see the textual conventions section. DEPENDS ON: eventInstanceType

This variable is mainly used to store additional information about the sub-component that is generating an event. For example this field may specify what cooling fan is faulty. DEPENDS ON: eventInstanceType

This variable dictates the urgency of action when a event occurs. There are four severity levels - Critical, Major, Minor, and Informational. Critical events are those, which require immediate operator intervention to prevent/reduce system down time. Major events require quick attention and Minor events possibly require some attention. Informational events indicate the occurrence of events that may need to be investigated.

This table contains only normal events and this variable represents the time when the event become active, i.e. the number of seconds since Jan 1, 1970 12:00AM.

This variable contains a description of the event and reasons behind the event. This is a free format alpha-numeric string that is set by the entity generating this event. This variable may be empty if there is no usefull information to report. The maximum length of this string is 255 characters.

This variable indicates whether the event is service affective or not

This variable represents the InstanceId of a particular event in the event current table. In brief the instanceId refers to the sub-component generating this event in the system, for example 1 for port 1. For more details see the textual conventions section. DEPENDS ON: eventInstanceType

Indicates the former sequence number of a cleared event in the event table. Not intended to read but only used in trap notifications.

Indicates whether the event is delta (automatically and immediately cleared) or normal (not automatically cleared). Not intended to read but only used in trap notifications.

Represents the node ID of the sending network element. If not supported should be set to 0. Not intended to read but only used in trap notifications.

Represents the trap status. 0 means cleared, 1 means happened.

This trap is used to inform network management system that a delta fault event (events that are automatically cleared) has occured or a normal fault event (not automatically cleared) state has been set on. Objects are used as follows: - eventSeqNum is the sequence number of the event. For normal type of events must equal to the sequence number of the event in the events table. - eventEventId specifies what fault event has occured. - eventName specifies the name of the fault event. - eventSetTime indicates when fault event has occured (delta events) or when fault has been set on (normal events). - eventSeverity reports the severity level of the event. - eventInstanceType indicates what kind of object is faulty. - eventInstanceId specifies what instance is faulty. - eventInstanceName may contain textual description for the faulty object. - eventServAffective specifies whether the event is immediately service affcetive. - eventDescription reports possible additional information about the event. - trapPersistence tells whether this event is a delta or normal event. - trapSenderNodeId specifies the node ID of the sending network element if configuring it is supported for the network element, otherwise 0. - sysObjectID specifies what kind of equipment reports the fault event. For more information see the eventTable specification

This trap is used to inform network management system that a normal type fault event has been cleared (state set off). Objects are used as follows: - eventSeqNum is the sequence number of the this clearing event. Note that the sequence number of the cleared event is reported in the trapRefSeqNum object. - eventEventId specifies what event has been cleared. - eventSetTime indicates when fault event has been cleared. - eventInstanceType indicates what kind of object has been faulty. - eventInstanceId specifies what instance has been faulty. - trapRefSeqNum specifies the sequence number of the cleared event (i.e. the sequence number was assigned for the event in the events table). - trapSenderNodeId specifies the node ID of the sending network element if configuring it is supported for the network element, otherwise 0. - sysObjectID specifies what kind of equipment reports the clearing event. For more information see the eventTable specification

An entry in protoBasedVlanTable.

sysLog enabled/disabled for the switch.

An entry in sysLogTypeTable.

An entry in sysLogServerTable.

An entry in diffservMapTable.

0-63

0-7

An entry in diffservPortTable.

An entry in mrstpBridgeTable.

The tree index of the MRSTP.

Enabled/disabled on the mrstp bridge.

An indication of what version of the Spanning Tree Protocol is being run. The value decLb100(2) indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return ieee8021d(3). If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.

The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.

The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.

The total number of topology changes detected by this bridge since the management entity was last reset or initialized.

The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.

The cost of the path to the root as seen from this bridge.

The port number of the port which offers the lowest cost path from this bridge to the root bridge.

The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.

The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.

This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.

This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to mrstpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]

The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of mrstpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of mrstpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

A table that contains port-specific information for the Spanning Tree Protocol.

A list of information maintained by every port about the Spanning Tree Protocol state for that port.

The port number of the port for which this entry contains Spanning Tree Protocol management information.

The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of mrstpPort.

The ports current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see mrstpPortEnable), this object will have a value of disabled(1).

The enabled/disabled status of the port.

The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.

The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.

The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.

The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this ports segment.

The Port Identifier of the port on the Designated Bridge for this ports segment.

The number of times this port has transitioned from the Learning state to the Forwarding state.

Indetify the bridge index that this port joined to in MRSTP.

The administrative value of the Edge Port parameter. A value of true(1) indicates that this port should be assumed as an edge-port, and a value of false(2) indicates that this port should be assumed as a non-edge-port.

The operational value of the Edge Port parameter. The object is initialized to the value of the corresponding instance of dot1dStpPortAdminEdgePort. When the corresponding instance of dot1dStpPortAdminEdgePort is set, this object will be changed as well. This object will also be changed to false on reception of a BPDU.

0 means unlimited

Last ignored: binding collision

Last ignored: expired leases

Last ignored: invalid interface

Last ignored: unsupported vlans

Last ignored: parsing error

Total ignored: binding collision

Total ignored: expired leases

Total ignored: invalid interface

Total ignored: unsupported vlans

Total ignored: parsing error

First Success Access

0: disable DHCP VLAN.

second

0 means any port

Two-rate three color marker enabled/disabled for the switch.

An entry in trTCMPortTable.

Two-rate three color marker enabled/disabled on the port.

Allowed CIR in pkts/s.

Allowed PIR in pkts/s.

0-63

0-63

0-63

An entry in loopGuardPortTable.

subnet-based vlan feature enabled/disabled for the switch.

dhcp vlan override enabled/disabled when subnet-based vlan is enabled.

An entry in subnetBasedVlanTable.

source ip for subnet-based vlan entry

source ip mask-bits for subnet-based vlan entry

name for subnet-based vlan entry

vid for subnet-based vlan entry

priority for subnet-based vlan entry

An entry in macAuthenticationPortTable.

Enabled/disabled on the mrstp bridge.

The configuration name that identifies the MST region and is used as one of the inputs in the computation of the MST Configuration Identifier.

This object identifies the MST revision that identifies the MST region and is used as one of the inputs in the computation of the MST configuration Identifier.

Configuration Digest.

13.22.f)

.

.

This table contains one entry for each instance of MSTP.

A conceptual row containing the status of the MSTP instance.

Uniquely identifies an instance. The entry of this table with index 0 presents always, represents CIST. When SET operation

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to 1. Empty (zero) most significant octes are not current.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to 1. Empty (zero) most significant octes are not current.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to 1. Empty (zero) most significant octes are not current.

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to 1. Empty (zero) most significant octes are not current.

This table contains one entry for each VlanId.

Information regarding the instance to which each Vlan is mapped.

The VlanId for which this entry contains the instance mapped.

An integer with values ranging from 0 to 64 that identify a the CIST/MSTI instance to which this VLAN is mapped

A table that contains generic information about every port that is associated with this bridge.

A list of information for each port of the bridge.

A unique value, greater than zero, for each Port. The value for each interface sub-layer must remain constant at least from one re-initialization of the entitys network management system to the next re- initialization.

The administrative value of the Edge Port parameter. A value of true(1) indicates that this port should be assumed as an edge-port, and a value of false(2) indicates that this port should be assumed as a non-edge-port.

.

.

0 means CIST.

Bridge priority, in steps of 4096.

.

.

.

.

.

.

.

0 means CIST.

The value of mstpPortIndex of the Port in mstpPortTable.

.

Port priority, in steps of 16.

.

.

.

.

.

.

An entry in radiusAuthServerTable.

An entry in radiusAcctServerTable.

An entry in tacacsAuthServerTable.

An entry in tacacsAcctServerTable.

An entry in authenticationTypeTable.

An entry in accountingTypeTable.

An entry in authorizationTypeTable.

An entry in portIsolationTable.

Port isolation enabled/disabled on the port. Enable(1) to be isolated and not exchange packets.

L2PT feature enabled/disabled for the switch

L2PT destination mac address

An entry in l2ptTable.

L2PT protocols enabled/disabled on the port

L2PT point-to-point protocols enabled/disabled on the port

L2PT port role on the port

An entry in vlanMappingPortTable.

An entry in vlan-mapping rule table

The name of vlan-mapping entry

interface port id

inner vid

translated vid

priority

An entry in transceiverSerialInfoTable.

Index of transceiverSerialInfo. It is referred to dot1dBasePort

Transceiver module status.

Transceiver module vendor name.

Part number provided by transceiver module vendor.

Serial number provided by transceiver module vendor.

Revision level for part number provided by transceiver module vendor.

Transceiver module vendors manufacturing date code

Transceiver module type names

An entry in transceiverDdmInfoTable.

Index of transceiverDdmInfo. This will be referred to dot1dBasePort

Transceiver DDM information type. 1: Temperature 2: Voltage 3: TX Bias 4: TX power 5: RX power

Transceiver high alarm threshold. The unit for temperature is 0.01C The unit for voltage is 0.01V The unit for TX bias is 0.01mA The unit for TX/RX power is 0.01dbm

Transceiver low alarm threshold. The unit for temperature is 0.01C The unit for voltage is 0.01V The unit for TX bias is 0.01mA The unit for TX/RX power is 0.01dbm

Transceiver high warn threshold. The unit for temperature is 0.01C The unit for voltage is 0.01V The unit for TX bias is 0.01mA The unit for TX/RX power is 0.01dbm

Transceiver low warn threshold. The unit for temperature is 0.01C The unit for voltage is 0.01V The unit for TX bias is 0.01mA The unit for TX/RX power is 0.01dbm

Transceiver current DDM value. The unit for temperature is 0.01C The unit for voltage is 0.01V The unit for TX bias is 0.01mA The unit for TX/RX power is 0.01dbm

Transceiver DDM information description. Show N/A if transceiver DDM information is not available.

An entry in dot3OamPortTable.

The OAM functions supported on this Ethernet-like interface. OAM consists of separate functional sets beyond the basic discovery process that is always required. These functional groups can be supported independently by any implementation. These values are communicated to the peer via the local configuration field of Information OAMPDUs. Setting unidirectionalSupport(0) indicates that the OA entity supports the transmission of OAMPDUs on links that are operating in unidirectional mode (traffic flowing in one direction only). Setting loopbackSupport(1) indicates that the OAM entity can initiate and respond to loopback commands. Setting eventSupport(2) indicates that the OAM entity can send and receive Event Notification OAMPDUs. Setting variableSupport(3) indicates that the OAM entity can send and receive Variable Request and Response OAMPDUs.

The dot1agCfmMep table entry

Size of data to be included in the LBM Data TLV

Defines the Vlan Counter Table for providing, via SNMP, the capability of performing vlan counting operations at a remote host and having their results of these operations are stored in the table.

Defines an entry in the VlanCounterTable.

VlanID where the vlan counter applies.

Average receive Octets

Total received packet number

Total received multicast-packet number

Total received Broadcast-packet number

Total received tagged-packet number

Total received packet number in size of 0 to 64 Octets

Total received packet number in size of 65 to127 Octets

Total received packet number in size of 128 to 255Octets

Total received packet number in size of 256 to 511 Octets

Total received packet number in size of 512 to 1023 Octets

Total received packet number in size of 1024 to 1518 Octets

Total received packet number in size larger than 1519 Octets

Specifies the time-out value, in seconds, for a vlan counter operation.

Specifies the time-out value, in seconds, for a vlan counter operation.

Port where the vlan counter applies. (Only support one or all bit setting now)

A system memory pool entry

The memory pool id

Name of the memory pool

Total size of memory pool in bytes

Used size of memory pool in bytes

Utilization of memory pool in bytes

An entry in pppoe ia port & vlan table

interface port id