MMPF-MIB: View SNMP OID List / Download MIB

This trap is issued when a fan is failured.

This trap is issured when a temperature become abnormal.

This trap is issued when a voltage is failured.

This trap is issued when a equipment is failured.

This trap is issued when a COM-COM bus parity error is occurred.

This trap is issued when a COM-COM bus ready alarm error is occurred.

This trap is issued when a Stby COM-Bridge pci serr is occurred.

This trap is issued when failured to write version at file.

This trap is issured when a fan is recovered.

This trap is issured when a temperature is recovered.

This trap is issued when a voltage is recovered.

This trap is issued when a equipment is recovered.

This trap is issued when a COM-COM bus parity error is recovered.

This trap is issued when a COM-COM bus ready alarm error is recovered.

This trap is issued when a Stby COM-Bridge pci serr is recoverd.

This trap is issued when recover from failure status to write version at file.

Indicates the software version number of this equipment

It is used to set the date and time to the realtime clock of this equipment

Indicates the table of the FAN information of this equipment.

Indicates the entry of the FAN information of this equipment.

Indicates the index value to identify the FAN in the equipment uniquely. If machine is 9110, the range is 1 to 6. If machine is 9120, the range is 1 to 10.

Indicates the character string which describes the FAN type.

Indicates the status of the FAN operation. If it is set to 1, the FAN operation is normal. If it is set to 2, the FAN operation is abnormal.

Indicates the information of the voltages of the equipment.

Indicates the entry of the information of the voltages of the equipment.

Indicates the Index value to identify the COM Package in the equipment uniquely.

Indicates the index value to identify uniquely the voltage provided by the power unit of the equipment.

Indicates the character string which describes the power unit type and com type.

Indicates the observed voltage, in milli-volt (mV).

Indicates the statsus of the voltage. If it is set to 1, the voltage is within the normal range. If it is set to 2, the voltage is in the abnormal range.

Indicates the table of the Temperature information of this equipment.

Indicates the entry of the information of the temperature of the equipment.

Indicates the Index value to identify the COM Package in the equipment uniquely.

Indicates the character string which describes the com unit type.

Indicates the status of the temperature of this equipment inside. If it is set to 1, the temperature is within the normal temperature range. If it is set to 2, the temperrature is in the abnomal range.

Indicates the temperature of the equipment inside, in degree (Celusius).

Indicates the temperature of the equipment inside, in degree (Celusius).

Indicates the higher threshold of the normal temparature range for the equipment, in degree (Celsius).

Indicates the table of the outside equipment information.

Indicates the entry of the outside equipment information.

Indicates the index value to identify the outside equipment uniquely.

Indicates the character string which describes the external equipment type.

Indicates the status of the outside equipment operation. If it is set to 1, the outside equipment operation is normal. If it is set to 2, the outside equipment operation is abnormal.

Indicates the table of the percentage of cpu using information.

Indicates the entry of the percentage of cpu using information.

Indicates the index value to identify the package in the equipment uniquely.

Indicates the index value to identify the time collecting percentage of cpu using uniquely.

Indicates the character string which describes the slot type.

Indicates the character string which describes the time type of collecting percentage of cpu using.

Indicates the percentage of cpu using.

A table that contains information about interface card.

A entry Indicates that contains information about interface card.

Indicates slot number of the interface card.

Indicates kind of the interface card.

Indicates the side which was used for setting up

Indicates the firmware version in operation.

Indicates the firmware version of side A.

Indicates the firmware version of side B.

Indicates the firmware version of BOOT/DP.

Indicates the table of Ether port information.

Indicates the entry of each Ether ports information.

Indicates the interface number assigned to the Ether port uniquely in the equipment. Each Ethernet port identified by this object is the same Ethernet port identified by the same number of the ifIndex.

Indicates the type of the Loop-back test. If it is set to 2, the internal Loop-back test is executed. The Loop-back test is finished when one test packet has been sent. If it is set to 1, the Loop-back testing is not being executed, which means it is in the normal mode.

Indicates the operation mode of the port. In case of Antomatical mode, the value 1 is set. In case of HDX10M, the value 2 is set. In case of FDX10M, the value 3 is set. In case of HDX100M, the value 4 is set. In case of FDX100M, the value 5 is set. In case of HDX1000M, the value 6 is set. -- @013 In case of FDX1000M, the value 7 is set. -- @013 The default value is 1.

Indicates the table of Ether port status information.

Indicates the entry of each Ether ports status information.

Indicates the interface number assigned to the Ether port uniquely in the equipment. Each Ethernet port identified by this object is the same Ethernet port identified by the same number of the ifIndex.

Indicates the result of the Loop-back test.

Indicates operation mode of the port. If it set to 1, operation mode is automatic. If it set to 2, operation mode is manual.

Indicastes current speed of the port in bps.

Indicates which current port status is full-duplex or half-duplex. If it is set to 1, it is half-duplex. If it is set to 2, it is full-duplex.

Indicates to validate the configuration of VLAN group. It is set to 1 when the configuration will be valid, after the value of objects had been modified.

It is used for VLAN configuration.

Indicates the table entry of the VLAN configuration.

Indicates the specified number to identify the VLAN. The lowest number must be assigned to the default VLAN.

Indicates the interface number assigned to the VLAN uniquely, within the equipment. The VLAN identified by this object is the same VLAN identified by the same number of ifIndex. The lowest number must be assigned to the default VLAN.

Indicates the name which is assigned to the VLAN for administrative purpose. I is used to assign or change the name of VLAN. In the initial state, only default is registered as the default VLAN. The default VLAN name cannot be changed.

No description.

This is the table entry of the VLAN group name registration.

This is the table entry of the VLAN group name registration.

This is the index to identify VLAN group. The value of this index and the index mpVlanIndex must be assigned uniquely,witrhin the range of 2 - 4095.

This object is the name defined to this VLAN Group, for management purpose.

This object is used to create or delete the entry of mpVlanGroupTable. The value 1 is set to create the entry, and the value 2 is set to delete the entry.

This is the table type object of BigPipe name registration.

This is the entry of the mpVlanBigPipeTable.

No description.

This is the index to identify the BigPipe. The value of this index should be within 1 - 6.

This object is used to create or delete the entry of mpVlanBigPipeTable. The value 1 is set to create the entry, and the value 2 is set to delete the entry.

This object is used to specify the communication status of BigPipe to VLAN. If the value is set to 1, frames to/from all VLANs (except VLANs registered in mpVlanBigpipeVidControlTable) are passed. If the value is set to 2, frames to/from all VLANs (except VLANs registered in mpVlanBigpipeVidControlTable) are filtered. The default value is 1.

This is the table type object of the interface (Ethernet port and logical ELAN port) subsucription to VLAN.

This is the table entry of mpVlanIntfTable.

This is the index to identify the existing VLAN to which the interfaces are subscribed. When the equipment is just shipped from factory, all the Ethernet ports are subscribed to the default VLAN.

This is the index to identify the Ethernet port number or logical ELAN port number subscribed to this VLAN. The value of this index is the same as ifIndex.

This object is used to register or delete the interface to this VLAN. The value 1 is set to register the interface to this VLAN, and the value 2 is set to delete the interface from this VLAN. When all the interfaces are deleted from this VLAN, the table entry of this VLAN is also deleted.

This is the table type object of the VLAN subscription to VLAN Group.

This is the table entry of mpVlanGroupIntfTable.

This is the index to identify the existing VLAN Group to which the VLANs are subscribed.

This is the index to identify the VLAN which is subscribed to this VLAN Group.

This object is used to register/delete the VLAN to/from this VLAN Group. The value 1 is set to register this VLAN to this VLAN Group, and the value 2 is set to delete this VLAN from this VLAN Group.

This is the table type object of the interface (Ethernet port) subscription to BigPipe.

This is the table entry of mpVlanBigPipeIntfTable.

This is the index to identify the existing BigPipe.

This is the index to identify the physical interface (Ethernet port) number subscribed to this BigPipe. The value of this index is the same as the value of ifIndex. The interface which is to be subscribed to BigPipe must not be subscribedany VLAN.

This object is used to register/delete the interface (Ethernet port) to/from this BigPipe. The value 1 is set to register this interface to this BigPipe, and the value 2 is set to delete this interface from this BigPipe.

This is the table type object of MAC address data of the VLAN.

This is the table entry of mpVlanMacTable.

This is the index to identify the existing VLAN. The value of this object is the VLAN number.

This object is the MAC address which is included in this VLAN.

This object is the Ethernet port number or logical ELAN number, from which the frame with source MAC address included in this VLAN can be received.This interface must belong to this VLAN. This object is set to 0 when no port is specified.

This object is used to create or delete the entry of this table. The value 1 is set to create the entry, and the value 2 is set to deletethe entry.

This is the table type object of the filter condition concerning to VID for BigPipe.

This is the table entry of mpVlanBigpipeVidControlTable.

This is the index to identify the BigPipe to which this filter condition is applied.

This object is the VID of VLAN or VLAN Group, to which this filter condition is applied.

This object is used to register/delete the VID filter condition for BigPipe. The value 1 is set to register the filter condition, and the value 2 is set to delete the filter condition.

A table that contains information about forwarding database per VLAN.

Each entry contains information about forwarding database per VLAN.

Indicates the VLAN number to specify the forwarding database per VLAN.

Indicates the destination MAC Address which belongs to the forwarding information of this VLAN.

Either the value 0, or the port number of the port from which the frame, which has a source address equal to the value of the mpVlanTPFdbMacAddress, was received. A value of 0 indicates that the port number has not been learned but that the bridge does have some forwarding information about this address.

The state of this entry. If it is 1, this entry is none of the following. If it is 2, this entry is not longer valie, but has not yet been flushed from the table. If it is 3, this entry was learned, and is being used. If it is 4, this entry is the bridges MAC addresses. If it is 5, this entry is the MAC address which was registered as filtering condition.

Indicates VLAN Tag Protocol ID used in this system. Range of VLAN Tag Protocol ID is from 1501(0x05dd) to 65535(0xffff) except 2048(0x0800), 2054(0x0806).

It is used for VLAN Tag PP(Point-to-Point) configuration.

Indicates the table entry of the VLAN Tag PP configuration.

Indicates the specified number to identify the VLAN Tag PP.

Indicates the interface number assigned to the VLAN Tag PP uniquely, within the equipment. The VLAN Tag PP identified by this object is the same VLAN Tag PP identified by the same number of ifIndex.

This is the index to identify the Ethernet port number or PPP port number subscribed to this VLAN Tag PP. The value of this index is the same as ifIndex.

Indicates the name which is assigned to the VLAN Tag PP for administrative purpose. It is used to assign or change the name of VLAN Tag PP.

Indicates the MAC address type. If the value is set to 1, global MAC address of the physical port is used. If the value is set to 2, private MAC address given by user (first 4 octets) is used. In case of 2, the last two octets is given by the value of the mpVlanTagPpIndex.

This object is used to register or delete the VLAN Tag PP.

This is the table type object of the filter condition concerning to the destination MAC address.

This is the table entry of mpBrgDestMacFilterTable.

This is the index to identify the VLAN to which this filter condition is applied.

This object is the destination MAC address which is filtered in this VLAN.

This object is used to create or delete the table entry. The value 1 is set to create the entry, and the value 2 is set to delete the entry.

This is the table type object of the filter condition concerning to the source MAC address.

This is the table entry of mpBrgSrcMacFilterTable.

This is the index to identify the VLAN to which this filter condition is applied.

This object is the source MAC address which is filtered in this VLAN.

This object is used to create or delete the table entry. The value 1 is set to create the entry, and the value 2 is set to delete the entry.

This is the table type ofject of the filter condition concerning to the destination port.

This is the table entry of mpBrgDestPortFilterTable.

This is the index to identify the destination port to which the filtering function is applied. The value of this index is the same as IfIndex.

This object is used to create or delete the table entry. The value 1 is set to create the entry, and the value 2 is set to delete the entry.

This is the table type ofject of the filter condition concerning to the source port.

This is the table entry of mpBrgSrcPortFilterTable.

This is the index to identify the source port to which the filtering function is applied. The value of this index is the same as IfIndex.

This object is used to create or delete the table entry. The value 1 is set to create the entry, and the value 2 is set to delete the entry.

Signal the system applications to save their config.

Signal the system applications to save their all config.

Specifies the type of logging for the events.

Specifies the log size.

Specifies filtering to be applied to incoming events. Bit mapped.

Specifies the index of the earliest event in the log.

Specifies the index of the latest event in the log.

Specifies the number of entries in the log.

Number of critical events in the log.

Number of major events in the log.

Number of minor events in the log.

Number of warning events in the log.

Number of informational events in the log.

Clear the log if set to clear.

Deletes entries in the log with specified severity.

Deletes entries in the log within the specified period. format : yyyy/[m]m/[d]d yyyy/m[m]/[d]d yyyy year mm month dd day

Event related details.

Details for particular event.

Index to the event in the table.

Indicates any code that may be associated with the source of the event. If no source is associated defaults to 0.

Indicates any code that may be associated with the event for further details. If no code is associated defaults to 0.

Timestamp of the event.

Indicates event severity.

Brief description of the recorded event.

Indicates the table of Trap Filter Information.

Indicates the entry of Trap Filter Information.

This object is the generic-trap to identify the trap to which this filter condition is applied.

This object is the specific-trap to identify the trap to which this filter condition is applied.

This object is the enterprise-trap to identify the trap to which this filter condition is applied.

This object specifies validity of trap filter.

This object is the name of the trap to be displayed.

Control Severity of Trap

severity of SpecificTrap

Index of Trap Severity Table

EventCode

Severity of Trap

Information of Trap

SysUpTime of Alm State Change

Table that describes active connections.

Describes each node in the session table.

The telnet port/async port that the session is using.

The starting time of the session

Status of the session user.

Session validity

This object controls the operating status of FTP server. The value 1 is set to enable the FTP server functionality, and the value 2 is set to disable the FTP server functionality.

This object is the counter of the total number of received Dhcp Relay request.

This is the counter of the total number of received Dhcp Relay reply.

This is the counter of the total number of discarded Dhcp Relay request.

This is the counter of the total number of discareded Dhcp Relay reply.

The current operational state of the Dhcp Relay Agent. This object is changed to 1 automatically, when mpDhcpRelayIfTable is created initially. Vice versa, this object is changed to 2 automatically, when mpDhcpRelayIfTable is deleted lastly. The default value of this object is 2.

This object specifies the maximum number of the hop count of Dhcp Relay Agent. The value of this object must be within the range of 1 - 16. The default value of this object is 4.

This is the table type object of the Dhcp Relay Agent interface data.

This object is the table entry of mpDhcpRelayIfTable.

This is the index to identify the router interface. The value of this index is the same as ifIndex.

The type of Transfer Mode. The default value of this object is 1.

This object is the counter of the total number of received BOOTP-REQUEST from this interface.

This is the counter of the total number of attempt to transmit BOOTP-REPLY to this interface.

This object is the counter of the total number of transmitted BOOTP-REQUEST.

This is the counter of the total number of discarded BOOTP-REQUEST.

This is the counter of the total number of discareded BOOTP-REPLY.

This object is used to create or delete the table entry. The value 1 is set to create the entry, and the value 2 is set to delete the entry.

This is the table type object of the Dhcp Relay Agent Destination IP Address data.

This object is the table entry of mpDhcpRelayAddrTable.

This is the index to identify the router interface. The value of this index is the same as ifIndex.

This object specifies the relaying destination IP address.

This object is used to create or delete the table entry. The value 1 is set to create the entry, and the value 2 is set to delete the entry.

This is the table type object of IP address excluding filter condition. Table of Exclude IP Filter.

This is the table entry of mpIpFilterExcludeTable. Exclude IP Filter fields.

This is the index to identify the IP address excluding filter entry.

This object specifies the input interface number to which the excluding filter is applied. The value of this object is the same as IfIndex of VLAN/LIS interface.

This object specifies the output interface number to which the excluding filter is applied. The value of this object is the same as IfIndex of VLAN/LIS interface.

This object specifies the source IP address to which the excluding filter is applied.

This object specifies the source IP address mask. 1 bit is set corresponding to the IP address part which is to be ignored.

This object specifies the destination IP address to which the excluding filter is applied.

This object specifies the destination IP address mask. 1 bit is set corresponding to the IP address part which is to be ignored.

This object specifies the IP option to which the excluding filter is applied. In case all the option is specified, the value 255 is set to this object. In case no option is specified, the value 0 is set to this object.

This obeject specifies the protocol to which the excluding filter is applied. In case of ICMP, the value 1 is set to this object. In case of TCP, the value 6 is set to this object. In case of UDP, the value 17 is set to this object.

This object specifies the receiving TCP/UDP port number to which the excluding filter is applied.

This object specifies the sending TCP/UDP port number to which the excluding filter is applied.

This object specifies the pakcket handling method corresponding to the ACK bit of TCP header. In case of discarding packet when ACK is off, the value 1 is set to this object. In case of not discarding packet when ACK is off, the value 2 is set to this object.

This object specifies the ICMP(error) sending method when a packet is discarded by IP filtering function. In case of sending ICMP error packet, the value 1 is set to this object. In case of not sending ICMP error packet, the value 2 is set to this object.

This object specifies the event handling method when a packet is discarded by IP filtering function. In case of reporting it by event, the value 1 is set to this object. In case of not reporting it by event, the value 2 is set to this object.

This object is used to create, delete, or modify this table entry.

This is the table type object of IP pass-filter condition data.

This is the table entry of mpIpFilterIncludeTable.

This is the index to identify the IP pass-filter condition table entry.

This object specifies the input interface to which the IP pass-filter is applied. The value of this index is the same as IfIndex of VLAN/LIS interface.

This object specifies the output interface to which the IP pass-filter is applied. The value of this index is the same as IfIndex of VLAN/LIS interface.

This object specifies the source IP address to which the IP pass-filter is applied.

This object specified the source IP address mask. 1 bit is set corresponding to the IP address part which is to be ignored.

This object specifies the destination IP address to which the IP pass-filter is applied.

This object specified the destination IP address mask. 1 bit is set corresponding to the IP address part which is to be ignored.

This object specifies the IP option to which the IP pass-filter is applied. In case all the option is specified, the value 255 is set to this object. In case no option is specified, the value 0 is set to this object.

This obeject specifies the protocol to which the IP pass-filter is applied. In case of ICMP, the value 1 is set to this object. In case of TCP, the value 6 is set to this object. In case of UDP, the value 17 is set to this object.

This object specifies the receiving TCP/UDP port number to which the IP pass-filter is applied.

This object specifies the sending TCP/UDP port number to which the IP pass-filter is applied.

This object specifies the pakcket handling method corresponding to the ACK bit of TCP header. In case of discarding packet when ACK is off, the value 1 is set to this object. In case of not discarding packet when ACK is off, the value 2 is set to this object.

This object specifies the valid time period of this IP pass-filter condition. When the valid time period expired, this entry is deleted automatically. In case of setting the value 0 to this object, this IP pass-filter condition lasts until it is deleted by operator command.

This object is used to create, delete, or modify this table entry.

This object is the counter of total number of the receiving packets discarded by this IP filter.

This object is the counter of total number of the receiving packets discarded by this IP filter.

The table of static route.

A entry of static route.

This object specifies destination IP Address of static route.

This object specifies network mask of static route.

This object specifies next-hop IP Address of static route. The value 0 is specified when route type is other,reject or local.

This object specifies the outgoing ifIndex.

This object specifies the route type. The route type other(1) is not reflected to IP routing table. The route type reject(2) is used to discard corresponding IP packet.

This object specifies route priority. The entry which route priority is the smallest in usable next-hop is reflected to IP routing table when route priority is different in every next-hop at the case of multi-path.

This object specifies route tag. In case route type is reject, setting to this object is prohibited.

This object specifies status of this entry. When entry is deleted, invalid(2) is set.

The route priority table of the routing protocol unit. The value of this table is the default value of each routing protocol of this system. It is used for tie-break when the requirement of the addition of routing table for the same network from plural routing protocols occur and route priority is the same.

A route priority entry of the routing protocol.

This object specifies the protocol of IP routing table.

This object specifies route priority value.

The table which is used to distribute route information to different routing protocol. It defines condition of routing table to be distributed and value to be used at distributing.

The entry which is used to distribute route information to different routing protocol.

This object specifies import-list number.

This object specifies whether routing table corresponding to the condition is distributed or ignored.

This object specifies a condition by the outgoing interface. The value 0 means it is outside of the condition decision.

This object specifies the network address. It is shared with the network condition and the range condition.

This object specifies the network mask. It is shared with the network condition and the range condition.

This object specifies the status of condition about network address.

This object specifies the status of condition about network address range.

This object specifies the condition about next-hop. The value 0 means it is outside of the condition decision.

This object specifies IP address or router ID of advertising router.

This object specifies the status of condition about advertising router.

This object specifies the condition about metric. The value 0 means it is outside of the condition decision.

This object specifies the condition about route type. The value 0 means it is outside of the condition decision.

This object specifies route tag.

This object specifies the status of condition about route tag.

This object specifies the condition about protocol ID. The value 0 means it is outside of the condition decision.

This object specifies the network address which is applied when routing table corresponding to the condition is distributed.

This object specifies the mask address which is applied when routing table corresponding to the condition is distributed.

This object specifies the status of network address which is applied when routing table corresponding to the condition is distributed.

This object specifies the metric value which is applied when routing table corresponding to the condition is distributed.

This object specifies the next-hop IP address which is applied when routing table corresponding to the condition is distributed.

This object specifies the route tag which is applied when routing table corresponding to the condition is distributed.

This object specifies the external route type which is applied when routing table corresponding to the condition is distributed to OSPF.

This object specifies status of this entry. When entry is deleted, invalid(2) is set.

The table of addressing information relevant to this entitys ifIndex.

The addressing information for one of this entitys ifIndex.

The index value which uniquely identifies the interface to which this entry is applicable. The interface referred by a particular value of this index is the same interface as identified by the same value of ifIndex.

This is the index to identify VPN the entry. The value of this index must be assigned uniquely, witrhin the range of 1 - 65535.

The table of IP group information relevant to this entitys VPNID.

The IP group information for one of this entitys VPNID.

This is the index to identify the VPN entry. The value of this index must be assigned uniquely, witrhin the range of 1 - 65535.

The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue response if a management station attempts to change this object to an inappropriate value.

The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol.

The total number of input datagrams received from interfaces, including those received in error.

The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc.

The number of input datagrams discarded because the IP address in their IP headers destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.

The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful.

The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.

The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.

The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).

The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams.

The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion.

The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down.

The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity.

The number of IP fragments received which needed to be reassembled at this entity.

The number of IP datagrams successfully re- assembled.

The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received.

The number of IP datagrams that have been successfully fragmented at this entity.

The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Dont Fragment flag was set.

The number of IP datagram fragments that have been generated as a result of fragmentation at this entity.

The number of routing entries which were chosen to be discarded even though they are valid. One possible reason for discarding such an entry could be to free-up buffer space for other routing.

This object is the counter of total number of the receiving packets discarded by this IP filter.

This object is the counter of total number of the receiving packets discarded by this IP filter.

When an entry is created it autmatically becomes valid(1). When this object is set to invalid(2) then this entry will be deleted.

The table of addressing information relevant to this entitys VPNID & IP addresses.

The addressing information for one of this entitys VPNID & IP addresses.

This is the index to identify the VPN entry. The value of this index must be assigned uniquely, witrhin the range of 1 - 65535.

The index value which uniquely identifies the interface to which this entry is applicable. The interface referred by a particular value of this index is the same interface as identified by the same value of ifIndex.

The IP address to which this entrys addressing information pertains. This IP address must always be a unicast IP address and it should never be a Class D or E IP address.

The subnet mask associated with the IP address of this entry. The value of this object is an IP address with the network part bits set to all 1s and all the hosts part bits set to all 0s.

The value of this object is the broadcast IP address for this entry. The broadcast IP address is the the IP address with the host part bits set to all 1s or all 0s.

The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.

When an entry is created it autmatically becomes valid(1). When this object is set to invalid(2) then this entry will be deleted.

This object refers to the encapsulation type for the interface of this entry. For VLAN interfaces the encapsulation type can only be set to dix(2) or snap(3). For LIS interfaces the encapsulation type can only be set to none(1).

This object indicates operation for data gram. to forwarding(1). When this interface is IP host, this object is set to not-forwarding(2).

Effective time of the Dynamic VPN IP ARP table (mpIpVpnIpNetToMediaTable). The value 0 means infinity.

This object indicates whether an ICMP redirect message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(network unreachable in) message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(network unreachable out) message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(host unreachable in) message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(host unreachable out) message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(protocol unreachable in) message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(protocol unreachable out) message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(port unreachable in) message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(port unreachable out) message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(fragmentation needed and DF set in) message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(fragmentation needed and DF set out) message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(source route failed in)message is transmitted to this Interface.

This object indicates whether an ICMP destination unreachable(source route failed out)message is transmitted to this Interface.

This object indicates whether an ICMP time exceeded(time to live exceeded in transit in) message is transmitted to this Interface.

This object indicates whether an ICMP time exceeded(time to live exceeded in transit out) message is transmitted to this Interface.

This object indicates whether an ICMP time exceeded(fragment reassembly time exceeded in) message is transmitted to this Interface.

This object indicates whether an ICMP time exceeded(fragment reassembly time exceeded out) message is transmitted to this Interface.

This object indicates whether an ICMP parameter problem(in) message is transmitted to this Interface.

This object indicates whether an ICMP parameter problem(out) message is transmitted to this Interface.

This object controls the operating status of the Proxy ARP in this Interface.This object is set to 1 to enable the Proxy ARP functionality, and is set to 2 to disable the Proxy ARP functionality.

This object controls the operating status of the Directed Broadcast Forwarding in this Interface. This object is set to 1 to enable the Directed Broadcast Forwarding functionality, and is set to 2 to disable the Directed Broadcast Forwarding functionality.

This object controls the operating status of the Path Through Forwarding in this Interface. This object is set to except 0 to enable the Path Through Forwarding functionality, and is set to 0 to disable the Path Through Forwarding functionality.But, this number must be in relation to the direction-list.

This object controls the operating status of the Extended Static Routing in this Interface. This object is set to except 0 to enable the Extended Static Routing functionality, and is set to 0 to disable the Extended Static Routing functionality.But, this number must be in relation to the direction-list.

The table of IP cidr information relevant to this entitys VPNID.

The IP cidr information for one of this entitys VPNID.

This is the index to identify the VPN entry. The value of this index must be assigned uniquely, witrhin the range of 1 - 65535.

The number of current mpIpVpnIpCidrRouteTable entries that are not invalid.

This entitys IP Routing table.

A particular route to a particular destina- tion, under a particular policy.

This is the index to identify the VPN entry. The value of this index must be assigned uniquely, witrhin the range of 1 - 65535.

The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the mpIpVpnIpCidrRouteMask object is not equal to x.

Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the mpIpVpnIpCidrRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the mpIpVpnIpCidrRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the mpIpVpnIpCidrRouteDest object is not equal to mpIpVpnIpCidrRouteDest.

30

On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0.

The ifIndex value which identifies the local interface through which the next hop of this route should be reached.

The type of route. Note that local(3) refers to a route for which the next hop is the final destination; remote(4) refers to a route for which the next hop is not the final destina- tion. Routes which do not result in traffic forwarding or rejection should not be displayed even if the implementation keeps them stored internally. reject (2) refers to a route which, if matched, discards the message as unreachable. This is used in some protocols as a means of correctly aggregating routes.

The routing mechanism via which this route was learned. Inclusion of values for gateway rout- ing protocols is not intended to imply that hosts should support those protocols.

The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old can be implied except through knowledge of the routing protocol by which the route was learned.

A reference to MIB definitions specific to the particular routing protocol which is responsi- ble for this route, as determined by the value specified in the routes mpIpVpnIpCidrRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntactically valid object identif- ier, and any implementation conforming to ASN.1 and the Basic Encoding Rules must be able to generate and recognize this value.

The Autonomous System Number of the Next Hop. The semantics of this object are determined by the routing-protocol specified in the routes mpIpVpnIpCidrRouteProto value. When this object is unknown or not relevant its value should be set to zero.

The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes mpIpVpnIpCidrRouteProto value. If this metric is not used, its value should be set to -1.

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes mpIpVpnIpCidrRouteProto value. If this metric is not used, its value should be set to -1.

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes mpIpVpnIpCidrRouteProto value. If this metric is not used, its value should be set to -1.

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes mpIpVpnIpCidrRouteProto value. If this metric is not used, its value should be set to -1.

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes mpIpVpnIpCidrRouteProto value. If this metric is not used, its value should be set to -1.

The row status variable, used according to row installation and removal conventions.

This entitys IP Routing table.

A route to a particular destination.

This is the index to identify the VPN entry. The value of this index must be assigned uniquely, witrhin the range of 1 - 65535.

The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.

The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes mpIpVpnIpRouteProto value. If this metric is not used, its value should be set to -1.

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes mpIpVpnIpRouteProto value. If this metric is not used, its value should be set to -1.

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes mpIpVpnIpRouteProto value. If this metric is not used, its value should be set to -1.

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes ipRouteProto value. If this metric is not used, its value should be set to -1.

The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agents IP address on that interface.)

The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the mpIpVpnIpRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant mpIpVpnIpRouteType object.

The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.

The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old can be implied except through knowledge of the routing protocol by which the route was learned.

Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the mpIpVpnIpRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the mpIpVpnIpRouteMask by determining whether the value of the correspondent mpIpVpnIpRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the mpIpVpnIpRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the routes mpIpVpnIpRouteProto value. If this metric is not used, its value should be set to -1.

A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the routes mpIpVpnIpRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.

The IP Address Translation table used for mapping from IP addresses to physical addresses.

Each entry contains one IpAddress to `physical address equivalence.

This is the index to identify the VPN entry. The value of this index must be assigned uniquely, witrhin the range of 1 - 65535.

The interface on which this entrys equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

The media-dependent `physical address.

The IpAddress corresponding to the media- dependent `physical address.

The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the mpIpVpnIpNetToMediaTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant mpIpVpnIpNetToMediaType object.

This entitys Static Proxy ARP table.

This entitys Static Proxy ARP table.

This is the index to identify the VPN entry. The value of this index must be assigned uniquely, witrhin the range of 1 - 65535.

The interface on which this entrys equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

The IpAddress corresponding to the media- dependent `physical address.

The IpAddress corresponding to the media- dependent `physical address.

When an entry is created it autmatically becomes valid(1). When this object is set to invalid(2) then this entry will be deleted.

The table of ICMP group information relevant to this entitys VPNID.

The ICMP group information for one of this entitys VPNID.

This is the index to identify the VPN entry. The value of this index must be assigned uniquely, witrhin the range of 1 - 65535.

The total number of ICMP messages which the entity received. Note that this counter includes all those counted by mpIpVpnIcmpInErrors.

The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.).

The number of ICMP Destination Unreachable messages received.

The number of ICMP Time Exceeded messages received.

The number of ICMP Parameter Problem messages received.

The number of ICMP Source Quench messages received.

The number of ICMP Redirect messages received.

The number of ICMP Echo (request) messages received.

The number of ICMP Echo Reply messages received.

The number of ICMP Timestamp (request) messages received.

The number of ICMP Timestamp Reply messages received.

The number of ICMP Address Mask Request messages received.

The number of ICMP Address Mask Reply messages received.

The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by mpIpVpnIcmpOutErrors.

The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counters value.

The number of ICMP Destination Unreachable messages sent.

The number of ICMP Time Exceeded messages sent.

The number of ICMP Parameter Problem messages sent.

The number of ICMP Source Quench messages sent.

The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects.

The number of ICMP Echo (request) messages sent.

The number of ICMP Echo Reply messages sent.

The number of ICMP Timestamp (request) messages sent.

The number of ICMP Timestamp Reply messages sent.

The number of ICMP Address Mask Request messages sent.

The number of ICMP Address Mask Reply messages sent.

The table of ping management information relevant to this entitys ICMP echo identifier.

The ping management information for one of this entitys ICMP echo identifier.

This is the index to identify the ping entry. The value of this index must be assigned uniquely, within the range of 1 - 65535.

The value of this object is the VPNID for this entry, within the range of 1 - 65535.

The value of this object is the destination IP address for this entry. This IP address must always be a unicast IP address and it should never be a Class D or E IP address.

The value of this object is the ping request number of the times.

The value of this object is the ping data length, within the range of 0 - 65507.

The value of this object is the TOS value in ping packet, within the range of 0 - 0xfe.

The value of this object is the TTL value in ping packet, within the range of 1 - 255.

The value of this object is the ping time out value, within the range of 1 - 60 seconds.

The value of this object is ifIndex. IP address assigned ifIndex is set as source IP address in ping packets.

This object refers to the ping entry status. When this object is set to create(1), ping entry is created. Set to inProgress(2), ping is Started. When a reply or icmp error receiveed and time out occured, the status become complete(3). This object can not set to complete(3). Set to destroy(4), entry is deleted.

This object refers to the ping result status.

This value of this object is the error source IP address in icmp error reply message.

This is the table type object of the RIP sending operation mode.

This is the table entry of mpRip2IfconfTable.

This object specifies the IP address of the interface to which the RIP packet is sent.

This object specifies the RIP sending mode of this interface. In case of Sprit Horizon with Poisoned Reverse, the value 1 is set to this object. In case of Sprit Horizon, the value 2 is set to this object.

The flag about Split-Horizon of this interface.

The flag which shows whether IP address of interface that condition is Down is transmitted as Host Route to this Interface.

This object specifies the metric value to be added to the route information of RIP-response which is received from this interface.

This object specifies the metric value to be added to the route information of RIP-response which is sent to this interface.

The timing when default route is advertised to this interface.

The metric value of default route to be used when the advertised timing(mpRip2IfConfDefType) is set to always.

The next-hop IP addess of default route to be used when the advertised timing (mpRip2IfConfDefType) is set to always.

The route tag of default route to be used when the advertised timing(mpRip2IfConfDefType) is set to always.

The protocol of routing table to be used for condition decision when the advertised timing (mpRip2IfConfDefType) is set to importList.

The route tag of default route to be used when the advertised timing(mpRip2IfConfDefType) is set to always.

The route priority value which is used when the route information of RIP-response received from this interface is reflected. The value 0 means route priority is not used for each interface.

The Neighbor information table to transmit RIP-response with unicast.

The Neighbor information Entry to transmit RIP-response with unicast.

This object specifies IP Address of Neighbor which transmits RIP-response with unicast.

This object specifies version of RIP-response.

This object is used to create, delete, or modify this table entry.

The table for importing route information to other routing protocols or RIP.

The table for importing route information to other routing protocols or RIP.

This object specifies protocol of IP routing table.

This object specifies import list number.

This object is used to create, delete, or modify this table entry.

The table to specify route priority to each network at creating IP routing table.

The entry to specify route priority to each network at creating IP routing table.

This object specifies network IP address.

This object specifies network mask.

This object specifies the value of route priority.

This object is used to create, delete, or modify this table entry.

The route priority value to be used when the route information of RIP-response received is reflected. It is used when the route priority of interface has not been registered (mpRip2IfConfRoutePriority is 0) and route information doesnt correspond to any network route priority table(mpRip2NetworkPriorityTable).

The community table (1-5 entries). This table lists community strings and their access levels. When a Snmp message is received by this entity, the community string in the message is compared with this table to determine access rights of sender.

A community table entry.

This object specifies the addition/deletion of a particular trap community.

This object specifies the addition/deletion of a particular community. Entries 1 and 2 are reserved for public access( read-only ) and NECs NMS read -write.

A value of readWrite(2) allows the community to read and write all objects in the MIB. A value of readOnly(1) allows the community to read all objs.

IP address of the registered NMS. This is actually a lists of IP addresses, maximum of 5. A special indexing must be implemented to get all the list of IP addresses for each entry.

Configurable community string with access rights defined by the value of sysCommunityAccess.

The trap receiver table (0 to 5 entries). This table lists the addresses of stations that should receive trap messages from this entity when an exception condition occurs.

A trap receiver table entry.

This object specifies the row for a particular trap community.

This object specifies the addition/deletion of a particular trap community.

This object specifies the recipient of a generated trap. AS of the moment only a NMS station is supported.

For type NMS,IP address for trap receiver. (For now type NMS is yet supported). For telephone,fax, and pager, phone number. For email, this is an Internet email address.

Community string used for trap messages to this trap receiver.

if IPaddress is 0.0.0.0, NMS doesnt SET LockMIB. if not, only 1 NMS is successing to SET LockMIB. note : NMS must SET own IPaddress to LockMIB before

Monitoring Group related details.

Details for a group of monitored statistics.

Specifies the table entry.

Name of the port/module to which the info in the table entry applies to.

Instance to which the info in the table entry applies to.

Interval at which the polling for values is done.

Setting this field to disable deletes the entry from the list of monitored groups.

The text value of the monitor group. For release 1, read-only but release 2 will allow the user to set the monitor group name to any textual description.

Object related statistics details.

Details of statistics.

Specifies the table entry.

Monitoring Group that this obj belongs to.

OID of the object.

Textual equivalent of the object.

Current value of the object.

Cumulative rate of the object.

Rate of change of the objetcs statistics.

Indicates the table of operator mode user for CLI

Indicates the entry of operator mode user information.

This is the index to identify the existing operator mode user.

This object is the operator user name.

This object is the operator user password which is used for user login.

This objects is the operator user password entered by user at login.

This object specifies the addition/deletion of a operator.

Indicates the table of supervisor mode user for CLI

Indicates the entry of supervisor mode user information.

This is the index to identify the existing supervisor mode user

This object is the supervisor user name.

This object is the supervisor user password which is used for user login.

This objects is the supervisor user password entered by user at login.

This object specifies the addition/deletion of a supervisor.

This table contains ATM local interface configuration parameters, one entry per ATM interface port.

This list contains ATM interface configuration parameters and state variables.

Indicates the index value to identify the ATM interface in this equipment. Each ATM interface identified by this object is the same interface identified by the same number of ifIndex.

An prefix assigned for administrative purpose. This value is displayed as the instance of atmInterfaceAdminAddress object of ATM MIB.

An ESI assigned for administrative purpose. This value is displayed as the instance of atmInterfaceAdminAddress object of ATM MIB.

This object sets the maximum number of the sum of VPI/VCI bit number that are able to use at this interface.

This table contains VCC configuration parameters, one entry per ATM interface port.

This list contains VCC configuration parameters and state variables.

Indicates the index value to identify the ATM interface in this equipment. Each ATM interface identified by this object is the same interface identified by the same number of ifIndex.

The type of frame format for use at this ATM interface.

Indicates whether the F4 OAM functionality is supported or not, for the ATM interface of this equipment. This object can be modified only when all the ATM interfaces are blocked. If it is set to 1, the F5 OAM functionality is supported. If it is set to 2, it is not supported.

Indicates whether the F5 OAM functionality is supported or not, for the ATM interface of this equipment. This object can be modified only when all the ATM interfaces are blocked. If it is set to 1, the F5 OAM functionality is supported. If it is set to 2, it is not supported.

It is used to set the timer value of the LOF (Loss of Frames) failure detection timer (msec). It is possible to set the integer of a multiple of 100.

It is used to set the timer value of the LOS (Loss of Signal) failure detection timer (msec). It is possible to set the integer of a multiple of 100.

It is used to set the timer value of the LOF (Loss of Frames) recovery detection timer (msec). It is possible to set the integer of a multiple of 100.

It is used to set the timer value of the LOS (Loss of Signal) recovery detection timer (msec). It is possible to set the integer of a multiple of 100.

It is used to set the timer value of the LOP (Loss of Pointer) failure detection timer (msec). It is possible to set the integer of a multiple of 100.

It is used to set the timer value of the LOP (Loss of Pointer) recovery detection timer (msec). It is possible to set the integer of a multiple of 100.

It is used to set the value of CDV(Cell Delay Variation) which is used for ATM Mega-Link.

It is used to set clock mode of ATM. If it is set to 1, the clock received from the line is used. If it is set to 2, the internal clock is used.

Indicates the table of SSCOP layer parameter configuration.

Indicates the entry of SSCOP layer configuration.

Indicates the index value to identify the ATM interface in this equipment. Each ATM interface identified by this object is the same interface identified by the same number of ifIndex.

It is used to set the timer value of the SSCOP connection control PDU re-sending interval timer (msec). The timer value must be the same as the that of the equipment connected to itself. It is possible to set the integer of a multiple of 250.

It is used to set the timer value of the POLL PDU re-sending interval timer, which is used when there is no SD PDU to be sent, in the data transmission phase (msec). The timer value must be the same as that of the equipment connected to itself. It is possible to set the integer of a multiple of 250.

It is used to set the timer value of the STAT PDU waiting timer (msec). This is the connection observation timer in the data transmission phase. When it expires, the connection is disconnected. The timer value must be the same as that of the equipment connected to itself. It is possible to set the integer of a multiple of 250.

It is used to set the timer value of the POLL PDU sending interval timer in the data transmission phase (msec). The timer value must be the same as that of the equipment connected to itself. It is possible to set the integer of a multiple of 250.

It is used to set the timer value of the POLL PDU sending interval timer, which is used when there is no SD PDU to be sent, in the data transmission phase (msec). The timer value must be the same as that of the equipment connected to itself. It is possible to set the integer of a multiple of 250.

Indicates the MAX retry count value of the SSCOP connection control PDU sending.

Indicates the sending timing of the POLL PDU. After the PDUs as many as the number specified by this object are sent, one POLL PDU is sent.

This table contains ATM Signaling configuration parameters, one entry per ATM interface port.

This list contains ATM signaling configuration parameters and state variables.

Indicates the index value to identify the ATM interface in this equipment. Each ATM interface identified by this object is the same interface identified by the same number of ifIndex.

Indicates whether the SVC functionality is supported or not, for the ATM interface of this equipment. If it is set to 1, SVC functionality is supported. If it is set to 2, it is not supported.

This specifies the ATM Forum UNI version which is used by the ATM ports of this equipment as the ATM Signaling functionality. This object can be set only when all the ATM ports are closed. It is set to 1 in the case of UNI3.0, and is set to 2 in the case of UNI3.1.

This table contains ILMI configuration parameters, one entry per ATM interface port.

This list contains ILMI configuration parameters and state variables.

Indicates the index value to identify the ATM interface in this equipment. Each ATM interface identified by this object is the same interface identified by the same number of ifIndex.

This object indicates ILMI Function support status.

Indicates the table of the statistics data of the SONET or SDH base ATM interface.

Indicates the entry of the statistics data of each ATM interface.

Indicates the index value to identify the ATM interface uniquely within the equipment. Each ATM interface identified by this object is the same ATM interface identified by the ifIndex.

Indicates the counter value of the VPI/VCI error.

Indicates the counter value of the receiving FIFO over-run error.

Indicates the counter value of the received invalid cell.

Indicates the counter value of the received free buffer empty.

Indicates the counter value of the Rx Status Queue Almost Full.

Indicates the counter value of the Tx Status Queue Almost Full.

Indicates OOL(Out of Lock) error counter value.

Indicates LOC(Loss Of Cell Delineation) error counter value.

Indicates the ATM cell HEC error counter value.

Indicates OCD(Out Of Cell Delineation) error counter value.

Indicates the counter value of the FIFO overflow.

Indicates the counter value of the parity error.

Indicates the C2 error counter value.

Indicates the LOP(Loss of Pointer) error counter value.

Indicates the Path Alarm Indication error counter value.

Indicates the Path Remote Path Indication error counter value.

Indicates the B3 error counter value.

Indicates the Path FEBE error counter value.

Indicates the B2 error counter value.

Indicates the Line FEBE error counter value.

Indicates the Line Alarm Indication error counter value.

Indicates the Line Remote Path indication error counter value.

Indicates the OOF(Out of Frame) error counter value.

Indicates the B1 error counter value.

Indicates the LOS(Loss of Signal) error counter value.

Inicates the LOF(Loss of Frame) error counter value.

Indicates the counter value of the incoming packets.

Indicates the counter value of the incoming octets.

Indicates the counter value of the outgoing packets.

Indicates the counter value of the outgoing octets.

This table contains network prefix of ATM address got by ILMI.

This list contains network prefix of ATM address got by ILMI.

A unique value which identifies the ATM Port.

The network Prefix for ATM address.

Indicates the validity of the network prefix.

This table contains VPL configuration parameters, one entry per ATM interface port.

This list contains VPL configuration parameters and state variables.

Indicates the index value to identify the ATM interface in this equipment. Each ATM interface identified by this object is the same interface identified by the same number of ifIndex.

The VPI value of the VPL. Note that the VPI=0 is not used for a VPL not associated with a VCL. The maximum VPI value cannot exceed the value allowable by the atmInterfaceMaxVpiBits.

This object is implemented only for a VPL which terminates a VPC (i.e., one which is NOT cross-connected to other VPLs). Its value specifies the desired administrative state of the VPL. The up and down states indicate that the traffic flow is enabled and disabled respectively for this VPL.

This object indicates the current operational status of the VPL. The up and down states indicate that the VPL is currently operational, or not operational, respectively. The unknown state indicates that the status of this VPL cannot be determined.

The value of MIB IIs sysUpTime object at the time this VPL entered its current operational state. If the current state was entered prior to the last re-initialization of the agent, then this object contains a zero value.

This object indicates shaping type used for VPC status.

The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VCL.

This object is used to create, delete or modify a row in this table. To create a new VCL, this object is initially set to createAndWait or createAndGo. This object must not be set to active unless the following columnar objects exist in this row: atmVclReceiveTrafficDescrIndex, atmVclTransmitTrafficDescrIndex. In addition, if the local VCL end-point is also the VCC end-point: atmVccAalType. In addition, for AAL5 connections only: atmVccAal5CpcsTransmitSduSize, atmVccAal5CpcsReceiveSduSize, and atmVccAal5EncapsType.

This table contains information on ATM traffic parameters.

This list contains ATM traffic parameters.

Indicates the index of ATM traffic entry.

Indicate the CDV(Cell Delay Variation) value

A table that is used for registoring LIS name.

An entry of LIS name.

A number that uniquely assigned to the LIS.

An interface number that uniquely assigned to the LIS of the Unit. The LIS recognized by this number is the same as what is recognized by same number of ifIndex.

A name assigned to the LIS for management purpose. This object is used for setting or changing a name of the LIS.

This object is used for registoring or deleting an entry of the table. 1 is set when registroing and 2 is set when deletion.

A table including LIS information.

An entry in LIS management table. Registoring LIS (1) Manager satation generates a LIS entry in mpLisAdminTable by setting mpLisAdmRowStatus as createAndWait(5). (2) Manager station, if necessary, sets value of management object of mpLisAdminTable. (3) Manager station enables a LIS entry by setting mpLisAdmRowStatus as active(1). Deletion of LIS (1) Manager station disables a LIS entry bu setting mpLisAdmRowStatus as notInService(2). (2) A LIS is deleted by setting mpLisAdmRowStatus as destroy(6). An agent may release all related resources at the moment.

This object shows a unique number assigned to this LIS.

This object identifies extistence or non-existence of ATM ARP server. If it exists, 1 is set. If it does not exist, 2 is set.

This object shows a type of connection between the LIS and an ATM ARP server. If it is SVC, 1 is shown. If it is PVC, 2 is shown.

This object assigns ATM address of an ATM ARP server in the LIS.

This object assigns a number of ATM port which is used when the LIS is connected to the ATM server by PVC. If these are conencted by SVC, this object shows currently assigned number of ATM port.

This object assigns a number of VPI which is used when the LIS is connected to the ATM server by PVC. If these are conencted by SVC, this object shows currently assigned number of VPI.

This object assigns a number of VCI which is used when the LIS is connected to the ATM server by PVC. If these are conencted by SVC, this object shows currently assigned number of VCI.

This object assigns a number of traffic ID which is used when the LIS is connected to the ATM server.

This object shows status of connection between the LIS and an ATM ARP server in follwing number: Open = 1 Being configurated = 2 Available to use = 3 Available to transmit to ATM = 4 Available to transmit and receiving to/from ATM = 5 Available to receive from ATM = 6 Being disconnected = 7 Waiting for disconnection = 8

This object shows the number of retrying of connection request caused by connection failure between ATM ARP server and the LIS.

This object shows status of connection between the LIS and an ATM ARP server in following number: the LIS is available = 1 waiting for In-ATM-ARP-request = 2 not available due to failure = 3 not available by configuration = 4

This object assignes ATM address that is used by the LIS interface.

This object assignes IP address that is used by the LIS interface.

This object assignes subnet mask of IP addresss that is used by the LIS interface.

This object assignes number of ATM port that is used by the LIS interface.

This object shows the number of ARP tables that are registored in the LIS.

This object assigns the maximum size of transmitted AAL5 CPCS PDU payload in octet.

This object assigns the maximum size of received AAL5 CPCS PDU payload in octet.

This object shows the number of default traffic ID that is used by the LIS interface.

The object is used for generating, deleting or modifying a row of the table. In case of of modifying this entry, this object must be changed from active(1) to notInService(2).

The table includes information of ATM ARP table.

The entry includes information of each ATM ARP table. Registration of PVC or static SVC (1) Manager generates an ATM ARP management entry in mpLisAtmArpAdminTable by setting mpLisAtmArpAdmRowStatus as createAndWait(5). (2) Manager sets the number of management object of mpLisAtmArpAdminTable if necessary. (3) Manager enables the ATM ARP entry by setting mpLisAtmArpAdmRowStatus as active(1). Deletion of PVC or static SVC (1) Manager disables the ATM ARP entry by setting mpLisAtmArpAdmRowStatus as notInService(2). (2) ATM ARP is deleted by setting mpLisAtmArpAdmRowStatus as destroy(6). An agent may release all related resources at the moment.

This object shows the unique number assigned to the LIS.

This object shows the type of connection between ATM ARP client and the LIS. If it is dynamic SVC, 1 is shown. If it is static SVC, 2 is shown. If it is PVC with aging, 3 is shown. If it is PVC without aging, 3 is shown.

This object is used for configuring or acknowledging of destination IP address. if the connection between ATM ARP client and the LIS is PVC. If the connection is dynamic SVC or static SVC, the object cannot be set. However it shows the currently used destination IP address.

This object is used for configuring or acknowledging of destination ATM address. if the connection between ATM ARP client and the LIS is PVC. If the connection is dynamic SVC or static SVC, the object cannot be set. However it shows the currently used destination ATM address.

This object assigns an ATM address that is used at the interface of the LIS.

This object assigns a number of ATM port which is used when the LIS is connected to the ATM client by PVC. If these are conencted by dynamic SVC or static SVC, this object shows currently assigned number of ATM port.

This object assigns a number of VPI which is used when the LIS is connected to the ATM client by PVC. If these are conencted by dynamic SVC or static SVC, this object shows currently assigned number of VPI.

This object assigns a number of VCI which is used when the LIS is connected to the ATM client by PVC. If these are conencted by dynamic SVC or static SVC, this object shows currently assigned number of VCI.

This object shows the number of traffic ID that is used for PVC connection between ATM ARP cliennt and the LIS.

This object shows status of ATM ARP table in follwing number: the table is available = 1 waiting for acknowledge of being available = 2 waiting for ATM-ARP-reply = 3 waiting for InATM-ARP-reply = 4 aging = 5 not available to service = 6 not available to use = 7

Indicates the passing time value (sec) of the ATMARP table aging timer. The timer is incre- mented by 1 sec.

This object shows the number of retrying of connection request caused by connection failure between ATM ARP client and the LIS.

The object is used for generating, deleting or modifying a row of the table. In case of modifying this entry. This object must be changed from active(1) to notInService(2).

The table includes information of VC table.

The entry includes information of each VC.

This object shows the unique number assigned to the LIS.

This object assign the destination IP address.

This object shows the type of VC management table. If the table is generated by originating connection, the type is 1. If the table is generated by receiving connection, the type is 2.

This object shows the status of VC connection as following numbers: Open = 1 Being configurated = 2 Available to use = 3 Available to transmit to ATM = 4 Available to transmit and receiving to/from ATM = 5 Available to receive from ATM = 6 Being disconected = 7 Waiting for disconection =8

Indicates the passing time value (sec) of the inactivity timer. The timer is incremented by 1 sec.

Indicates the remaining time value (sec) of the holding timer. The timer is incremented by 1 sec.

This object includes statistics information of the LIS.

This entry includes counters of each statistics information.

This object shows the unique number assigned to the LIS.

This object shows the number of transmission of ATM ARP request.

This object shows the number of receiving of ATM ARP reply.

This object shows the number of receiving of ATM ARP NAK.

This object shows the number of timed-out in waiting for ATM ARP reply.

This object shows the number of transmission of InATM ARP request.

This object shows the number of receiving of InATM ARP reply.

This object shows the number of receiving of InATM ARP request.

This object shows the number of timed-out in waiting for InATM ARP reply.

This object shows the number of disconenction by inactivity timer.

This object shows the number of disconenction by resource limitation.

This object show the number of ATM ARP table that is deleted due to aged out.

This object show the number of ATM ARP table that is deleted due to resource limitation.

This object show the number of packets transmitted to IP router part.

This object show the number of packets received from ATM interface.

This object show the number of packets that are discarded due to resource limitation.

This object show the number of discarded packets due to exceeding MTU.

This object show the number of discarded packets due to format error of SNAP in IP over ATM.

This object show the number of packets received from IP router part.

This object show the number of packets transmitted to ATM interface.

This object show the number of discarded packets due to route unknown.

This object show the number of discarded packets due to failure of ATM ARP server.

This object show the number of discarded packets due to failure of link.

This object show the number of discarded packets due to overflowing queue.

This object show the number of discarded packets due to illegal destination.

This object show the number of discarded packets that are received from IP router part due to exceeding MTU.

This object show the number of discarded packets due to configuration failure of connection.

This object show the number of discarded packets due to resource limitation in transmitting.

This object show the number of discarded packets due to exceeding the maximum number of VC connection.

This object shows the number of configuring of call.

This object shows the number of failure of call configuration due to exceeding the maximum simultaneous connections of VC.

This object shows the number of failure of call configuration due to resource limitation.

This object shows the number of called by ATM ARP client.

This object shows the number of refusing incoming call due to exceeding the maximum simultaneous connections of VC.

This object shows the number of refusing incoming call due to resource limitation.

This object shows the total number of currently registored PVC.

This object shows the total number of currently registored static SVC.

This object shows the total number of currently connected VC in IP over ATM functional block.

This object shows the value of inactivity timer in second.

This object shows the value of holding timer in second.

This object shows the value of ATM ARP reply waiting timer in second.

This object shows the value of In ATM ARP request waiting timer in second.

This object shows the value of In ATM ARP reply waiting timer in second.

This object sets the aging time of ATM ARP in second.

This obhject sets cycle time to check status of VC connection of ATM ARP server in second.

This object sets the number of retrying in case of failure of call configuration to ATM ARP server.

This object sets the number of retrying in case of failure of call configuration to ATM ARP client.

This object sets tne number of retrying of ATM ARP request in case of no response from ATM ARP server to which ATM ARP request is sent before timer expiration.

This object sets tne number of retrying of InATM ARP request in case of no response from ATM ARP client to which InATM ARP request is sent before timer expiration.

This object sets the maximum number of simultaneous connections that is used in IP over ATM functional block. This number is the sum of PVC, dynamic SVC and static SVC that are able to connect simultaneously.

The object sets the maximum number of queues include packets that are received from IP router.

Table of DNS name server IP addresses.

Entry of DNS name server IP address.

DNS name server IP address.

DNS name server table entry status.

Table of DNS Resource Records(RR).

Entry of DNS Resource Record.

Index of a particular entry.

The RRs host name field.

The RRs Time to Live field. Currently, this value can be set to -1 (infinity) only.

The RRs type field.

The RRs IP address field.

The RRs entry status.

Table of DNS local domain names.

Entry of DNS local domain name.

Index of a particular entry.

Local domain name field.

Local domain table entry status.

DNS cache maximum Time to Live(TTL).

A counter on how many RR queries have been sent to name server(s).

A counter on how many RR responses have been received from name server(s).

Indicates the table of the LEC information.

Indicates the entry of the LEC information.

Indicates the index value to identify this entry.

The aging time for the unused ARP cache entry (sec).

Indicate whether the LEC does the address learning by the LE_ARP_RESPONSE which is broadcasted to another LEC, or not. If the value enabled(1) is set, the LEC does the address learning. If the value disabled(2) is set, the LEC does not do the address learning.

Indicate whether the LEC disconnects the unused VCC for a time defined as C12. The time value is given by the lecVCCTimeoutPeriod (LEC MIB). If the value noCut(1) is set, the LEC does not disconnect the VCC. If the value myConnectCut(2) is set, the LEC disconnects only the VCC which the LEC sets up. If the value otherConnectCut(3) is set, the LEC disconnects only the VCC which the destination LEC sets up. If the value allCut(4) is set, the LEC disconnects all the VCCs.

Indicate the timing to send an unknown frame to the BUS. If the value soon(1) is set, the LEC sends the packet immediately. If the value later(2) is set, the LEC sends the packet after a time defined by mpLeUnknownFrameWaitTime. If the value noSend(3) is set, the LEC does not send the packet.

Indicates one of the LEC types described as follows: a) The LEC defined by ATM Forum b) The proprietary LEC (serverless method) defined by NEC. If it is set to 1, this entry uses the method defined by ATM Forum. If it is set to 2, this entry uses the proprietary LEC defined by NEC.

Indicates number of ATM port which is used for decision of primary ATM address.

Indicates the number of default send traffic ID that is used by LEC.

Indicates SEL of primary ATM address for LEC

Indicates the number of default receive traffic ID that is used by LEC.

Indicates the number of Lecs ID that is used by LEC.

Indicates the table of LECS information.

Indicates the table entry of LECS information. LECS Registration: 1) The object mpLecsRowStatus is set to createAndWait(5), to create LECS entry into the table mpLecsConfigTable. 2) The appropriate values are set to the object mpLecsConfigTable. 3) active(1) is set to the object mpLecRowStatus, to activate the LECS entry. LECS deletion: 1) notInService(2) is set to the object mpLecsRowStatus, to deactivate the LECS entry. 2) destroy(6) is set to the object mpLecRowStatus, to delete the LECS entry.

Indicates the index value to identify this table entry.

Indicates the type of the connection between this LEC and the LECS. If it is set to 1, the type is SVC for ATM address registration. If it is set to 2, the type is PVC for VPI/VCI registration.

Indicates the ATM address of the LECS.

Indicates the ATM interface number to which the LECS is connected.

Indicates the VPI of the Configuration Direct VCC.

Indicates the VCI of the Configuration Direct VCC.

Indicates the send traffic ID of the Configuration Direct VCC.

This object is used to create, delete, or modify the row within this table. Within each conceptual mpLecsConfigTable row, objects which are writable may be modified regardless of the value of mpLecsRowStatus. It is not necessary to set a rows status to notInService first.

Indicates receive the traffic ID of the Configuration Direct VCC.

Indicates the table of the Server Information.

Indicates the entry of the Server Information.