LJ4100mfp-MIB: View SNMP OID List / Download MIB

Returns or changes the Energy Star sleep value. If the value is greater than zero, then the device will go into energy saving sleep mode after the print engine has been idle for the number of seconds specified by this object. A value of zero means Energy Star is disabled and the device will not go to sleep based on print engine idle time. The value must be non-negative. Additional information: Returns or changes the Energy Star sleep value. The device will go into energy saving sleep mode after the print engine has been idle for the number of seconds specified by this object. LaserJet 4100mfp supports values of 0, 60, 900, 1800, 3600, 5400, 7200, 14400 seconds. A value of 0 means never enter sleep mode based on the print engine idle time. Setting to an unsupported value causes the printer to substitute a value (listed below) and to return <noError> status. Setting this value when the printer is in sleep mode will not cause it to wakeup unless it is set to 0. The values are as follow: <=0 snap to 0 >=1 and <= 479 snap to 60 (1 minute) >=480 and <= 1349 snap to 900 (15 minutes) >=1350 and <= 2699 snap to 1800 (30 minutes) >=2700 and <= 4499 snap to 3600 (1 hour) >=4500 and <= 6299 snap to 5400 (90 minutes) >=6300 and <= 10799 snap to 7200 (2 hours) >=10800 snap to 14400 (4 hours).

Returns eTrue if the device is in energy saving sleep mode, otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes the device to wake up, if it is in sleep mode. Setting SLEEP-MODE to eTrue causes the device to go into sleep mode. Additional information: This object returns eTrue if the device is in energy saving sleep mode, otherwise it returns eFalse. Setting this object to eTrue while the printer is awake will not change the printers current state and will return <genErr> status. NOTE: This object should behave this way when the printer does not have an instant-on fuser. Setting this object to eTrue while printer is already in Sleep Mode will not change the printers current state and will return <noError> status. Setting this object to eFalse while printer is already awake will not change the printers current state and will return <noError> status. Setting this object to eFalse while the printer is asleep causes the device to wake up.

To bring the PDL processing sub-system on or off line. If the device is a printer, then the printer does not process print job data when the printer is off line. PML communication persists. Additional information: When the printer is in the Offline state, printing will stop as soon as possible (no more sheets of media are pulled from input trays). The I/O is taken offline also. Setting to eOnline has the following affect: Printer will immediately go to or remain in the Online state; <noError> status is returned. If the printers current state is Offline with a pending error condition that prevents the printer from going to the Online state, the printer will remain in the Offline state; <genErr> status is returned Setting to eOffline has the following affect: Printer will immediately go to or remain in the Offline state; <noError> status is returned. If pages are being printed, those pages will complete with the printer in the Offline state. Setting to eOfflineAtEndOfJob has the following affect: If not in a job or already in the Offline state, the printer will immediately go to or remain in the Offline state; <noError> status is returned. If in a job and the current state is Online, the printer will remain in the Online state, with the value of this object as eOfflineAtEndOfJob, until the end of the job; <noError> status is returned. At the end of the job, the printer goes to the Offline state and the value of this object becomes eOffline. Setting this object to eOffline or eOnline before the end of the job causes the action for that value to be taken immediately.

A device can support a class of errors called continuable errors. When a continuable error is encountered, the device requires a continue event to occur before the device will continue operation. One continue event is setting the CONTINUE object to eInitiateAction. Devices can support other continue events, like auto-continue. A continue event causes the continuable error to be acknowledged, thus allowing the device to continue. Each device needs to list the continuable errors. If the device doesnt currently have an unacknowledged continuable error, the response will contain <genErr>. Additional information: See the CLEARABLE-WARNING and AUTO-CONTINUE objects for the errors that this object will clear.

Indicates if the device will automatically continue after encountering a continuable error. If AUTO- CONTINUE is set to eOn, the device will automatically generate continue event to acknowledge continuable errors. If AUTO-CONTINUE is set to eOff, then some other continue event will have to acknowledge the continuable error. Additional information: If this is set to eOn the device displays an error message and goes offline for ten seconds. After ten seconds the printer automatically returns to the online state. If this is set to eOff then the device displays an error message and goes offline. It remains offline until the operator presses the GO key or until the CONTINUE object is set. If the printer is not idle, the new value may not take effect until a job boundary is reached. If a get is done on this object before the job boundary is reached, the value last set will be returned.

This object will set the cAllPermDevices bit when a full perm storage initialization occurs (as would be the case for a brand new system or as a result of a powerup key sequence or PE-TEST-POWERUP-KEY-SEQUENCE object request). If only one device was initialized (as would be the case if a disk were added to an existing system or a formatter were swapped out), then only the appropriate collection bits will be returned. If there are no collection bits set then this indicates that no initialization took place.

The number of seconds the device waits after a job related continuable error occurs before automatically continuing. An example job related continuable error is the job requesting a media size that is not available. After the timeout expires, the device will continue processing the job as if a continue event occurred, such as the front panel continue key being pressed. If the value is -1, the device does not automatically continue after a job related continuable error occurs. If the value is 0, the device immediately continues. If the value is greater than 0, the value represents the timeout value in seconds. Additional information: This object is used only for media requests (size and/or name). LaserJet 4100mfp supports any value in the range of -1 to 3600. Setting to a value outside of that range causes the printer to substitute a value (listed below) and to return <noError> status. The values are as follow: <-1 snaps to -1 >3600 snaps to 3600 (60 minutes) The action that occurs when this timeout expires is explained by JOB-INPUT-AUTO-CONTINUE-MODE. It is not the same as the CONTINUE object being set to eInitiateAction or the Select key being pressed on the control panel. See the CONTINUE object description for information on the actions that occur for those conditions. The data for this object is stored in NVRAM.

Returns or sets the device behavior when the desired media is not currently available. cCancelJob - The device cancels the job. The device POS should explain what happens if this item is not the only item in the collection. cAutoMediaSizeOverride - The device is allowed to substitute a different size media. cAutoMediaNameOverride - The device is allowed to substitute a different media name. cUSMediaSizeOverride - The device is allowed to substitute US media sizes (letter, etc.) for ISO media sizes (A4, etc.). cISOMediaSizeOverride - The device is allowed to substitute ISO media sizes (A4, etc.) for US media sizes (letter, etc.). Additional information: If cCancelJob is set, the current print job will be canceled regardless of other item settings. At least one bit of the collection must be set; setting this object to zero will cause a status of <badValue> to be returned. This object applies to all media requests, including Manual Feed Requests. This object describes the action that is performed when the JOB-INPUT-AUTO-CONTINUE-TIMEOUT expires. The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions. The data for this object is stored in NVRAM.

The string displayed on the devices front panel in place of the printers built-in background status string. An example built-in background status string is 00 READY. Additional information: The display size for the OZ printers is 4 X 16. The value of this object and the current value of BACKGROUND-STATUS-MSG-LINE2-PART1 are displayed together on the 4-line display, but they must be set independently. If line 2,3 or 4 has been set, and the next message to be displayed only requires line 1, BACKGROUND-STATUS-MSG-LINE2-PART1, BACKGROUND-STATUS-MSG-LINE3-PART1, BACKGROUND-STATUS-MSG-LINE4-PART1 must be set to the null string to clear it. This object allows a message to be displayed when it is the highest priority message. Setting this object does not guarantee the message will be displayed; and reading it returns the value last written, not the currently displayed message (use prtConsoleDisplayBufferText to read the display). The priority assigned for displaying this message is one lower than the READY message. In other words, the only message that can be replaced by these objects is the READY message. To clear the message, write a null string to both this object and BACKGROUND-STATUS-MSG-LINE2-PART1.

The string displayed on the devices front panel in place of the printers built-in background status string. An example built-in background status string is 00 READY. Additional information: See BACKGROUND-STATUS-MSG-LINE1-PART1

The string displayed on the devices front panel in place of the printers built-in background status string. An example built-in background status string is READY. Additional information: See BACKGROUND-STATUS-MSG-LINE1-PART1

The string displayed on the devices front panel in place of the printers built-in background status string. An example built-in background status string is READY. Additional information: See BACKGROUND-STATUS-MSG-LINE1-PART1

Setting this object clears all the entries in the error log sub-tree. Additional information: Setting this object removes all errors that have been stored in the printers non-volatile memory.

Returns or sets the time that the printer will wait after an output bin becomes full and the printer is trying to deliver a sheet of media to that output bin. When the timeout expires, the job is processed according to the OUTBINn-OVERRIDE-MODE. A value of -1 indicates that the printer will wait for a continue event. A non- negative value is the number of seconds to wait. Additional information: A value of zero means to continue immediately. The value of this object is stored in NVRAM, so it is maintained across a power cycle. The data for this object is stored in NVRAM.

Indicates that the printer can create multiple, collated originals of a job and shows the level of support for this capability. cCollatedOriginals - The printer can create multiple collated originals, or mopies. This is the base functionality required by the other collection items. cProofAndHold - The printer saves a copy of the job while printing the first mopy. Later, this held job can be released and the rest of the mopies will print. cSecurityPrint - The printer spools the job and holds the job until the user releases the job by entering a password at the printers control panel. cAutoHighlight - The printer prints the job a number of times with a mail distribution list prepended to each job. A different mailing address is highlighted on each mopy. cCollatedAtSpeed - The printer can create multiple collated copies where all copies after the original are printed at engine speed. Additional information: Indicates that the printer can create multiple, collated originals of a job and shows the level of support for this capability. cCollatedOriginals - The printer can create multiple collated originals, or mopies. This is the base functionality required by the other collection items. Without disk, this object will not exist. This will be set at boot-up initialization. If the disk fails, in any way, then the disk error functionality will handle the situation. A color printer (Viper) that only has a RAMDISK installed is treated like there is no disk and therefore this object will not exist. The value of this object will be: !cCollatedOriginals - Only FLASH installed cCollatedOriginals - IDE is installed combined with/without FLASH cCollatedOriginals - RAMDISK is On combined with/without FLASH

The list of languages supported by the device. The languages are primarily, but not limited to, two character codes from ISO 639, each separated by a comma character. Additional information: This string will always be in the Roman-8 character set. See prtLocalizationLanguage for details about each language value.

The list of countries supported by the device. The countries are primarily, but not limited to, two character codes from ISO 3166, each separated by a comma character. Additional information: This string will always be in the Roman-8 character set. See prtLocalizationCountry for details about each country value.

Returns the amount of memory, in bytes, that the device has available for job-related processing or resources. Also known as driver work space (DWS) memory.

Writing this object simulates pressing a button on the control panel. Reading it will return the last key pressed either on the control panel or via PML. The device POS will specify which keys are supported.

A counter which increments whenever the contents of the front panel display changes. This object is implemented as a 32-bit signed integer which rolls over to zero when it reaches a maximum value.

Reading this object returns a 32-bit Cyclical Redundancy Check (CRC) which represents the current contents of the display. Additional information: This object has been implemented as a 32-bit CRC for this product.

Reading this object returns a graphical file format image representing the current pixel content of the display. The device POS will specify the expected screen resolution, color depth of the display and graphics file format for a given product (eg. 160x64x1 GIF format OR 640x240x4 JPEG format). If the image is large enough that it needs to be returned in multiple objects then each array object will contain a portion of the image. The image will then need to be reconstructed by a host application. An application that needs to determine if their is an additional object to be retreived will need to perform a GETNEXT operation until there are no more objects in the sub- tree. Additional information: This object returns a GIF image that represents the current contents of the 160x64x1 control panel display. Most display images require more than one instance of this object in order to retreive the complete GIF image.

Writing this object simulates pressing a key on the control panel. Reading it will return the last key pressed either on the control panel or via PML. This object obsoletes/replaces CONTROL-PANEL-BUTTON-PRESS object which was unable to represent each of the possible key combinations of our current control panels (ie. Full QWERTY keyboard). The device POS will specify the full range of keys supported by this object. Additional information: Writing this object simulates pressing a key on the control panel. Reading it will return the last key pressed either on the control panel or via PML. This object obsoletes/replaces CONTROL-PANEL-BUTTON-PRESS object which was unable to represent each of the possible key combinations of our current control panels (ie. Full QWERTY keyboard). The device POS will specify the full range of keys supported by this object. The Cayenne implementation of this object supports the Unified Key Encoding Scheme which is documented at http://clbu.boi.hp.com/main-fw/subsystems/lynx_hp/drivers/ cp/doc/UnifiedKeyEncoding.doc

Identifies the device model number as listed in the HP corporate price list (e.g. C2121A for DeskJet 500C). The string is as specific as possible. Products should note in POS if the model number on the CPL changes but the device reports the previous model number. If the model number changes based on the installed options, the POS should indicate if only the base model number is returned, or if the device senses the installed options and returns the correct model number. If possible, encode the model number in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: The value of this object does not change based on the installed options. The default of this object is the same on all LaserJet 4100mfp printers.

Identifies the device model name (e.g. DeskJet 1200C). The string is as specific as possible. Capitalization and spacing should match family naming conventions. Products should note in POS if the model name on the HP corporate price list changes but the device reports the previous device name. If the model name changes based on the installed options, the POS should indicate if only the base model name is returned, or if the device senses the installed options and returns the correct model name. If possible, encode the model name in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: Since the value of this object is frequently used in displaying a list of printers, it is kept relatively short in case systems have limited width for their display area. The model name does not change based on sensing of installed options.

Identifies the serial number for the device. If the SERIAL-NUMBER object is set by the user, then setting the object does not need to be protected. If the SERIAL-NUMBER object is set at the factory, then the SERVICE-PASSWORD object must be set correctly before the SERIAL-NUMBER object is writable. If this is a writable object, the POS should indicate the maximum supported string length. If possible, encode the serial number in a symbol set (like Roman-8) that matches the ASCII character set and limit the characters used to ASCII characters. Additional information: This value IS AFFECTED BY NVRAM resets, it is set to the default value of XXXXXXXXXX, when a NVRAM init is done.

Identifies the base system firmware date code. The date code will be encoded in the yyyymmdd format. There may be several versions of the base system firmware. The date code associated with the version of the base system firmware that is being used is reported. There may be other date code objects for other specific modules such as fonts, localization modules, etc.; these other datecode objects are device specific.

This identifies the system code firmware ROM revision code. The format for a revision is major_revision.minor_revision. There may be other ROM revision code objects for other specific ROMs such as font ROMs, localization ROMs, etc; these other ROM revision code objects are device specific.

User defined device name. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the <noError>. Additional information: The maximum supported string length is 32 characters. If the user entered string is too long, the device will store the first 32 characters and will return the <noError> status.

User defined device location. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the <noError>. Additional information: The maximum supported string length is 16 characters. If the user entered string is too long, the device will store the first 16 characters and will return the <noError> status.

User defined asset number. The POS should indicate the maximum supported string length. If the user entered string is too long, the device will store as much as possible and will return the <noError>. Additional information: The maximum supported string length is 8 characters. If the user entered string is too long, the device will store the first 8 characters and will return the <noError> status.

Returns an indication of the type of option installed in SIMM slot 1. eEmpty means the device did not detect any option installed in the interface slot. eUnknown means the device doesnt recognize the installed option. eUnSupported means the device recognizes the installed option, but does not support the option. eReadOnlyMemory means the installed option contains ROM Ics. eVolatileRandomAccessMemory means the installed option contains RAM ICs that loose data when the power is turned off. eNonVolatileRandomAccessMemory means that the installed option contains RAM ICs that do not loose data when the power is turned off. eFlashMemory means that the installed option contains a type of non-volatile RAM that needs to be erased before it can be written. eDiskDrive means the installed option contains a disk drive. eRamRom means the installed option contains both volatile random access memory and read only memory. eInputPHD means the installed option is an input paper handling device. eOutputPHD means the installed option is an output paper handling device. eIOCard means the installed option is an I/O card. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4100mfp. eRamRom is used to denote LaserJet 4100mfps combo simm.

Returns an indication of the capacity of the SIMM installed in SIMM slot 1. The capacity is dependent on the type of option, as indicated by the SIMM1-TYPE object. This object has no meaning if the installed option type is eUnknown or eReadOnlyMemory. This object contains the size, in bytes, if the installed option type is eVolatileRandomAccessMemory, eNonVolatileRandomAccessMemory, eFlashMemory, or eDiskDrive. If the type of the installed option is eRamRom, this object contains the size, in bytes, of the random access memory. If the type of the installed option is eInputPHD, the capacity indicates the number of input trays supported by the installed option. If the type of the installed option is eOutputPHD, the capacity indicates the number of output bins supported by the installed option. If the type of the installed option is eIOCard, the capacity indicates the number of logical I/O ports supported by the I/O card. Additional information: Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM1-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the SIMM is returned.

Returns an indication of the type of option installed in Bank 1 of SIMM slot 1. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.

Returns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 1. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM1-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.

Returns an indication of the type of option installed in Bank 2 of SIMM slot 1. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.

Returns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 1. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM1-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.

Returns an indication of the type of option installed in SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4100mfp. eRamRom is used to denote LaserJet 4100mfps combo simm.

Returns an indication of the capacity of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4100mfp. Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM2-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the SIMM is returned.

Returns an indication of the type of option installed in Bank 1 of SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.

Returns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM2-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.

Returns an indication of the type of option installed in Bank 2 of SIMM slot 2. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.

Returns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 2. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM2-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.

Returns an indication of the type of option installed in SIMM slot 3. See SIMM1-TYPE for a description.

Returns an indication of the capacity of the SIMM installed in SIMM slot 3. See SIMM1-CAPACITY for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4100mfp. Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM3-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the simm is returned.

Returns an indication of the type of option installed in Bank 1 of SIMM slot 3. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.

Returns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 3. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM3-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.

Returns an indication of the type of option installed in Bank 2 of SIMM slot 3. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.

Returns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 3. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM3-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.

Returns an indication of the type of option installed in SIMM slot 4. See SIMM1-TYPE for a description.

Returns an indication of the capacity of the SIMM installed in SIMM slot 4. See SIMM1-CAPACITY for a description. Additional information: This object is used for describing DIMMs instead of SIMMs on LaserJet 4100mfp. Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SIMM4-TYPE type is eVolatileRandomAccessMemory, eRamRom, or eFlashMemory. For eRamRom only the size of the Ram portion of the simm is returned.

Returns an indication of the type of option installed in Bank 1 of SIMM slot 4. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.

Returns an indication of the capacity of Bank 1 of the SIMM installed in SIMM slot 4. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM4-BANK1-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.

Returns an indication of the type of option installed in Bank 2 of SIMM slot 4. See SIMM1-TYPE for a description. Additional information: This object is used for describing the type of DIMM banks. Each physical DIMM slot has up to 2 banks.

Returns an indication of the capacity of Bank 2 of the SIMM installed in SIMM slot 4. See SIMM1-CAPACITY for a description. Additional information: Returns an indication of the capacity of the installed bank option in bytes. This object is not supported unless the SIMM4-BANK2-TYPE type is eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory, eSDRandomAccessMemory, eSRandomAccessMemory, or eFPMRandomAccessMemory.

Returns product information identifying the I/O card. Example: XXXX

Returns information describing the manufacture of the I/O card installed in MIO/EIO slot 1. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.

Returns an indication of the type of option installed in MIO/EIO slot 1. See SIMM1-TYPE for an explanation of the enumerations.

Returns product information identifying the I/O card. Example: XXXX

Returns information describing the manufacture of the I/O card installed in MIO/EIO slot 2. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.

Returns an indication of the type of option installed in MIO/EIO slot 2. See SIMM1-TYPE for an explanation of the enumerations.

Returns product information identifying the I/O card. Example: XXXX

Returns information describing the manufacture of the I/O card installed in MIO/EIO interface 3. May include serial number and firmware revision. Additional information: The format of the string returned is determined by the manufacturer of the EIO device. There is no standard for content of the string.

Returns an indication of the type of option installed in MIO/EIO interface 3. See SIMM1-TYPE for an explanation of the enumerations.

Returns product information identifying the PHD device. Example: XXXX

Returns information describing the manufacture of this particular PHD. May include serial number and firmware revision.

Returns an indication of the type of option installed as PHD 1. See SIMM1-TYPE for an explanation of the enumerations. Additional information: Returns an indication of whether or not the envelope feeder is installed on the printer. This object will return eInputPHD(10) when the envelope feeder is installed, and unknown_object_identifier when it is not.

Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: The LaserJet 4100mfp envelope feeder has a single tray.

Returns product information identifying PHD device 2. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns product information about the first paper handling device in the device chain.

Returns information describing the manufacture of PHD 2. May include serial number and firmware revision. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns the name of the manufacturer of the first paper handling device.

Returns an indication of the type of option installed in PHD interface 2. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns whether the device is an input device, an output device, or an unknown device which may be developed in the future.

Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least one (1) external paper handling device (EPHD) is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD2-TYPE) for the first EPHD in the device chain.

Returns product information identifying PHD device 3. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns product information about the second paper handling device in the device chain.

Returns information describing the manufacture of PHD 3. May include serial number and firmware revision. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns the name of the manufacturer of the first paper handling device.

Returns an indication of the type of option installed in PHD interface 3. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns whether the device is an input device, an output device, or an unknown device which may be developed in the future.

Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least one (1) external paper handling device (EPHD) is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD2-TYPE) for the first EPHD in the device chain.

Returns product information identifying PHD device 4. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns product information about the third paper handling device in the device chain.

Returns information describing the manufacture of PHD 4. May include serial number and firmware revision. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns the name of the manufacturer of the first paper handling device.

Returns an indication of the type of option installed in PHD interface 4. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns whether the device is an input device, an output device, or an unknown device which may be developed in the future.

Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least one (1) external paper handling device (EPHD) is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD2-TYPE) for the first EPHD in the device chain.

Returns product information identifying PHD device 3. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns product information about the fourth paper handling device in the device chain.

Returns information describing the manufacture of PHD 5. May include serial number and firmware revision. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns the name of the manufacturer of the first paper handling device.

Returns an indication of the type of option installed in PHD interface 5. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns whether the device is an input device, an output device, or an unknown device which may be developed in the future.

Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least one (1) external paper handling device (EPHD) is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD2-TYPE) for the first EPHD in the device chain.

Returns product information identifying PHD device 6. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns product information about the fifth paper handling device in the device chain.

Returns information describing the manufacture of PHD 6. May include serial number and firmware revision. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns the name of the manufacturer of the first paper handling device.

Returns an indication of the type of option installed in PHD interface 6. See SIMM1-TYPE for an explanation of the enumerations. Additional information: If at least one (1) external paper handling device is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns whether the device is an input device, an output device, or an unknown device which may be developed in the future.

Returns an indication of the capacity of the installed option. See SIMM1-CAPACITY for an explanation of the meaning of the value of this object. Additional information: If at least one (1) external paper handling device (EPHD) is attached to the printer, then this object will exist, otherwise ERROR-UNKNOWN-OBJECT-IDENTIFIER should be returned. This object returns the number of input trays or output bins, depending the the device type (see PHD2-TYPE) for the first EPHD in the device chain.

This object reports the current version of the Socket Ping Job Events capability. The version number is returned as a string in the format MAJOR.MINOR.SUB version. (eg. 1.0.1) If socket ping is not supported by this printer then the object is either not implemented or it returns a 0.

Writing this object allows a device self test to be started. Reading this object provides an indication what self-test is currently executing, if any. Actual self-test operation is device specific. A self test may not be allowed at any arbitrary time. If the device supports the requested self test, but can not start the execution of the self test when requested, the device will respond with <genErr>. If a non-destructive self test is being started, the device will generate a response before the self test is completed. RECOMMENDATION: If the device is ready (i.e. the NOT- READY-PRINTER object does not contain any items, except maybe being off-line) and is idle (i.e. the NOT-IDLE object does not contain any items), this request should always succeed. This provides a mechanism for driver writers to always determine if the action will succeed or not. Additional information: The eNonDestructiveSelfTest performs limited testing on the printer and its attached paper handling devices. After the self-test is complete a configuration page is printed. The recommended way to cause a configuration page to be printed is to use the PRINT-INTERNAL-PAGE object. Setting this object to eNonDestructiveSelfTest results in a status of <noError> and a value of eNonDestructiveSelfTest being returned. If the printer is not idle (whether printing an external job or printing an internal page), this action will be delayed until the next job boundary. See the PRINT-INTERNAL-PAGE object for more details.

Writing this object to a value other than eNotPrintingAnInternalPage causes the device to attempt to print an internally generated page. Reading this object provides an indication what internally generated page is currently being printed, if any. The actual page is device specific. Some devices may support continuously printing an internally generated page. Setting this object to eNotPrintingAnInternalPage terminates continuously printing internally generated pages. An internally generated page may not be allowed to be printed at any arbitrary time; under what conditions it will succeed or fail is device specific. If the device supports the requested page, but can not start printing the page when requested, the device will respond with <genErr>. RECOMMENDATION: If the device is ready (i.e. the NOT- READY-PRINTER object does not contain any items, except maybe being off-line) and is idle (i.e. the NOT-IDLE object does not contain any items), this request should always succeed. This provides a mechanism for driver writers to always determine if the action will succeed or not. Additional information: Previous products used ePCLDemoPage1ConfigurationPage(300) for the Configuration or Self Test page. This product uses eDeviceDemoPage1ConfigurationPage(3). LaserJet 4100mfp does not support continuously printing a demo page. When this object is set to a valid value, the status returned is <noError> and the value returned is ePrintingAnUnknownInternalPage. If the printer is idle, the page will be printed immediately. If the printer is currently printing another job, the internal page requested will not print until that job is finished. Setting this object to a valid value causes the desired page to be formatted and put in the printers print queue. While the page is being formatted a get on this object will return the value ePrintingAnUnknownInternalPage. Once the page (or pages) is finished being formatted, this object returns a value of eNotPrintingAnInternalPage, even though the page may not have finished being printed. Setting this object multiple times will queue up the requests, but only a limited number will be queued. Once the queue is full, additional requests will be ignored.

The ENGINE-SELF-DIAGNOSTIC object reveals current Engine Failures; it returns a BINARY string of two-byte Motor, Clutch, Solenoid and Sensor failure codes. Additional information: The ENGINE-SELF-DIAGNOSTIC object reveals current Engine Failures; it returns a BINARY string of two-byte Motor, Clutch, Solenoid and Sensor failure codes.

Returns or controls how the device will track clearable warnings. A clearable warning indicates a transient event in the device. The device will continue after the transient event occurs. If CLEARABLE-WARNING is eOff, the device does not track clearable warnings. If CLEARABLE-WARNING is eOn, all clearable warnings will be tracked until cleared (acknowledged). If CLEARABLE- WARNING is eJob, a clearable warning generated due to an event that occurs because of the print job being processed will be automatically cleared when the device has finished processing the job. Example clearable warning events include the device altering resolution or page protection due to memory constraints. The POS will document what transient events are treated as clearable warnings. Additional information: If set to eOn, the warning is displayed until the GO key is pressed or the CONTINUE object is set. If set to eJob, the warning is displayed until the end of the job in which it was generated.

Cancels the print job whose ID matches the value written to the CANCEL-JOB object. The host first learns the job ID using the CURRENT-JOB-PARSING-ID command. If the printer has completely processed the job, the printer responds with <badValue>. If the value of the CURRENT-JOB-PARSING-ID is smaller than the value written to the CANCEL-JOB object, then the printer responds with <badValue>. When read, returns the value of the last job ID what was canceled, or -1 to indicate no job has been canceled. Additional information: If the value written matches the ID of a job that is currently being canceled (for any reason), the printer responds with <noError>. LaserJet 4100mfp uses job IDs in the range of 0..32767. Because the ID number can wrap to zero, CURRENT-JOB-PARSING-ID may be smaller than the value written to this object; when this occurs, no error will result as long as the ID is for a currently processing job. This object is write only, so the comment in the general description stating the job ID or -1 will be returned on a read does not apply.

Returns the current value of an object in the job-info sub-tree whose value has changed. Define the object identifier for the object whose value has changed as job-info.required-field.optional-field.job-id. job-info represents the OID prefix of all objects in the job-info sub-tree. Required-field represents the OID field value that follows the job-info prefix. Since some objects in the job-info sub-tree have two OID fields between the job-info prefix and the job-id, the optional-field represents the OID field between the required-field and the job-id field, if present. Using this definition, the format for the JOB-INFO-CHANGE-ID binary value can be described as follows: Bytes 0-3 : required-field Bytes 4-7 : optional-field, or all zeros if there is no optional field Bytes 8-11: Job ID. Bytes 12-n : The value of the object job-info. required-field.optional-field.job-id. All multi-byte values stored in Motorola (big-endian) format, where the most significant byte occurs first. Additional information: OZ will use this object to report changes to the job-info-pages-printed and job-info-state objects. The required-field (bytes 0 through 3) will designate whether the change to be reported involves the pages printed (13) or job state (15). The optional-field (bytes 4 through 7) will always be zeroes. The value-field (bytes 12 through 15) will contain the new value for pages printed or job state cast to a 32-bit integer. Note: It is possible that traps generated by this object have the same value. This is caused by the architecture of the Oz System. In the Oz System, it is highly probable that the object value will change so rapidly that when the trap is processed, PML will read the same value twice. This is timing related and will generally be seen at the end of a job.

The time, in minutes, that the printer will wait before automatically deleting a held job. This allows the printer to automatically clean up jobs that have been forgotten (held but never released). Additional information: This only applies to temporary held jobs, i.e., HOLD=ON or PROOF. This is a global timer that only affects the jobs that are sent after it is set. A value of 0 means never delete the jobs. Setting it to an unsupported value causes the printer to substitute a value (listed below) and to return <noError> status. Smokey supports values of 0, 60, 240, 1440, and 10080 The values are as follows: <=0 snap to 0 (disabled) >=1 and <=150 snap to 60 (60 minutes) >=151 and <=840 snap to 240 (4 hours) >=841 and <=2880 snap to 1440 (1 day) >=2881 snap to 10080 (1 week)

Contains the printer assigned job identification for the job currently being processed by the processing PDL sub- system. The job ID is a monotonically increasing number. The job ID may be reset to zero at power-up and may roll over to zero after reaching some maximum value. Additional information: A value of -1 is returned when the printer is not parsing a job. When data for a new job is detected, this object is updated (the job may or may not turn out to be a Null Job); however, the trap does not occur until the printer determines that it is not a Null Job. (A job is considered to be a null job if it has no name or job attribute, causes no pages to be printed, and consumes MIN_JOB_SIZE (9) or fewer bytes.) A trapped value will differ from the previous value by one or more. Some job-info- objects are created when the first data bytes are received. If the printer determines that the job is a Null Job, the job-info- objects related to the Null Job are deleted. OZ retains the job-info- objects for the MAX_JOBS_IN_LIST (32) most recent jobs that are not Null Jobs. The first job received after power-up will have job ID 1, and the job ID will increment to 2,147,483,647 before rolling to zero. To distinguish whether a power cycle or a rollover causes a reduction in the job ID value, the object prtGeneralConfigChanges can be watched and if it increments at the same time as the drop is observed in the value of CURRENT-JOB-PARSING-ID, then a power cycle is the most likely cause.

Contains the first part of this print jobs name. The last OID field for this dynamic object contains the job ID. Additional information: The job name is the string specified by the NAME= parameter of the @PJL JOB command which allows a maximum of 80 characters. The first 40 characters are in this object and the second 40 are in job-info-name2. The symbol set is Roman-8. When jobs are nested, the value assigned to this object is the name provided by the most recent @PJL JOB NAME= command. If no name is provided, a null string is returned.

Contains the second part of this print jobs name. The last OID field for this dynamic object contains the job ID. Additional information: See job-info-name1.

Indicates what printer sub-systems are currently processing this print job. The last OID field for this dynamic object contains the job ID. cSourceSubsystem - some of the job is in the printer I/O subsystem. cProcessingSubsystem - some of the job is in the printer imaging processing subsystem. cDestinationSubsystem - some of the job is being printed. Additional information: For OZ, cSourceSubsystem and cProcessingSubsystem will always be set and cleared together. They are set when the beginning of the job is detected, and they are cleared when the end of the job is parsed. A non-printing job will never set cDestinationSubsystem. When a page is ready to be printed (the intermediate has been built and the page is `closed by the personality), cDestinationSubsystem will be set even if a page of a previous job is currently being printed. cDestinationSubsystem remains set until the last page of the job has finished printing. If a page requires extensive processing and allows all the previous pages of a job to complete printing, cDestinationSubsystem will remain set until the last page of the job has finished printing.

Indicates which I/O source, the print job was received over. The value maps to port numbering scheme supported in the DEVICE/SOURCE-SUBSYSTEM/IO/PORTS sub-tree.

Indicates the number of pages processed by the processing subsystem. If neither the cSourceSubsystem or the cProcessingSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the total number of pages processed for this job. The last OID field for this dynamic object contains the job ID. Additional information: This object is incremented by one when a page is processed (`closed by the personality), regardless of the number of pages that are printed as a result of the single page processed. In other words, it does not matter how many identical copies of a page are printed or no pages may be printed if operating in silent run mode, this count is incremented exactly once. A page is considered processed when all of the input data has been processed for a page (that is, when the intermediate has been produced, and the personality has `closed the page. At this time, the image of the page is not necessarily completely formed.)

Indicates the number of pages printed by the destination subsystem. If non of the cSourceSubsystem, cProcessingSubsystem or cDestinationSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the total number of pages printed for this job. This value may increase by two each time for duplex jobs. The last OID field for this dynamic object contains the job ID. Additional information: If multiple copies of a page are printed, each copy is counted individually.

Indicates the number of bytes of data processed by the processing subsystem. If neither of the cSourceSubsystem or cProcessingSubsystem items are in the associated JOB-INFO-STAGE object, then this object contains the size of this job, in bytes. The last OID field for this dynamic object contains the job ID. Additional information: This count may be incremented by values other than one as blocks of data are processed; blocks of data (which may be as large as 2K bytes) will be processed in a varying amount of time. During the processing of a job and even when a job completes, an exact count of the number of I/O bytes processed by the job is not necessarily to be expected.

Indicates the state of the job. The last OID field for this dynamic object contains the job ID. eAborted - the print job was aborted. eWaitingForResources - the print job requires resources that are not currently available. Example resources that can cause the job to wait include the print engine or PDL processor being unavailable. The print engine could be unavailable due to paper out, paper jam, staple out, stapler jam, marking agent low, output bin full, etc. The PDL processor could be unavailable due to an off-line condition. Each printer specific object specification should state which conditions cause a job to be waiting for resources and also state which objects can be retrieved by an application to determine the exact cause of a resource being unavailable. ePrinted - the job has printed. The related JOB-INFO- OUTCOME object indicates if any problems were encountered while the job was processed. eRetained - the job can be reprinted. eTerminating - the job was aborted or cancelled and is currently is terminating. eInterrupted - the job has been interrupted. The job can be continued. ePaused - the job has been paused. The job can be continuted. eCancelled - the job has been cancelled. eProcessing - the job is currently being printed normally.

Indicates if any warning or error conditions were encountered while processing the assoicated job. The last OID field for this dynamic object contains the job ID. Additional information: In OZ, warnings and errors are not recorded in this object. Although no meaningful information can be obtained from this object, it is kept around for the compatibility needs of existing software.

Indicates which output bins this job has delivered printed pages to. The last OID field for this dynamic object contains the job ID. Additional information: The bins designated by this collection include the printers own output bins as well as the `logical output bins associated with any attached external paper handling devices. (The mapping of the physical output bins of an external paper handling device to its `logical output bins depends on the usage mode of the device. For instance, in `mailbox mode, there is one-to-one correspondence of `logical output bins to physical bins, whereas in `stacker mode, one `logical output bin may map to several physical bins.) Although LaserJet 4100mfp come with two output bins -- a face-down bin on the top of the device and a face-up bin at the back of the device -- firmware will not provide a means of selecting between the two, nor will it report which of the two gets used. For this reason, bit 0 (cOutbin1) of this collection is being used to designate both of these bins together.

Indicates which physical output bins this job has delivered printed pages to. The last OID field for this dynamic object contains the job ID. Additional information: The output bins designated by the bits of this collection include the standard output bin(s) plus the physical bins of attached external paper handling devices. The configuration (if any) of external paper handling devices will determine the mapping of individual bits in this collection to the physical bins of the devices. For LaserJet 4100mfp, the cOutbin1 is used for Face Down bin, cOutbin2 is used for Face Up bin, and 3-15 are used for the 13 optional output bins (12 plus an extension to the Face Up bin) for backwards compatibility with Koala/Yukon and forwards compatibility with Klondike. However, since they cannot distinguish output going to the Face Up or Face Down bin in the firmware because the diverter can only be moved manually, bit 0 (cOutbin1) is being used to designate both of these bits together. If an external paper handling output device is connected, then bit 2 (cOutbin3) will represent the devices first output bin (and so on).

Returns the value that was set in PJL via the SET JOBATTR= command. Attribute objects are saved sequentially, starting with 1, after the start of a job. If more attributes are set than there are objects to store them, the excess JOBATTR values are ignored. If the corresponding SET JOBATTR= command has not been received when a get is done for this object, a status of <noSuchName> will be returned.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

Returns the value that was set in PJL via the SET JOBATTR= command. See JOB-INFO-ATTR-1 for details.

The number of requested collated copies. The value was supplied with the job via PJL QTY variable, the PostScript Collate and NumCopies entries in the page device dictionary, or via some other mechansim.

The page number being printed within the current copy of a collated multi-copy job. This value changes when the job-info-pages-printed changes. The job-info-pages- printed indicates the total number of pages printed in the job, while this object indicates the number of pages printed for this copy of a collated multi-copy job. Additional information: The number of pages in the current copy of a collated multi-copy job which have been completely printed and safely delivered to the output bin.

Number of pages in a single copy of a collated multi- copy job.

Number of collated copies completely printed and delivered to the output bin at time of query.

Contains the media size of the printed job. The media size of the first page will decide the media size of the entire job. The return value of this object will only be valid when the printer finishes printing the entire job.

Contains the media type of the printed job. The media type of the first page will decide the media type of the entire job. The return value of this object will only be valid when the printer finishes printing the entire job.

Contains the finishing option used on the printed job. The finishing option specified for the first page will decide the finishing option of the entire job. The return value of this object will only be valid when the printer finishes printing the entire job.

Contains the total number of simplex pages printed in a particular job

Contains the total number of duplex pages printed in a particular job

Contains the total number of monochrome pages printed in a particular job

Contains the total number of color pages printed in a particular job

Contains the total number of black pixels used in a particular job Additional information: This object reports kilodots. (A kilodot is 1000 dots.)

Contains the total number of yellow pixels used in a particular job Additional information: This object reports kilodots. (A kilodot is 1000 dots.)

Contains the total number of cyan pixels used in a particular job Additional information: This object reports kilodots. (A kilodot is 1000 dots.)

Contains the total number of magenta pixels used in a particular job Additional information: This object reports kilodots. (A kilodot is 1000 dots.)

Contains the total number of simplex pages scanned, indexed by media size. For each media size that is scanned, there are 6 bytes of information in the following format. media-size number of scanned pages 01 2345 Bytes 0-1 contain a value from the media-size enum and bytes 2-5 contain the number of the media size scanned. For example if a 10 Letter pages are scanned followed by 5 Legal pages scanned, the pValue of the object would be 02000A030005

Contains the total number of duplex pages scanned, indexed by media size. For each media size that is scanned, there are 6 bytes of information in the following format. media-size number of scanned pages 01 2345 Bytes 0-1 contain a value from the media-size enum and bytes 2-5 contain the number of the media size scanned. For example if a 10 Letter pages are scanned followed by 5 Legal pages scanned, the pValue of the object would be 02000A030005

Keeps track of what type of job is processed.

User name that is obtained by the driver through some internal method or from user input. Additional information: The following is a general description for all the JOB-MANAGEMENT objects described below. These object describe the attributes of the dynamic list containing all the stored jobs on the disk available for printing or deleting via the job-management feature. The jobs on this list are not deleted from the disk unless explicitly specified by the user. A print job may be specified for retention by PJL commands in the data stream. Following is a list of the PJL commands (i.e. these comments describe the PJL implementation and in some cases do not reflect the PML implementation.): @PJL SET HOLD=OFF|ON|PROOF|STORE|PRINT GENERAL DESCRIPTION: This variable specifies the retention classification of the job. The values indicate whether the job is printed immediately and/or stored. OFF: The job is printed but not retained on disk after printing. This is the default value. ON: This setting may be thought of as free proof-and-hold. The requested number of copies will be printed and the job will be temporarily stored on disk. The job will then be available for printing additional copies through the control panel and through PML. There will be a limit to the number of these temporary jobs that may be stored, and when the limit is exceeded the oldest job will be removed from the disk. PROOF: One copy of the job is printed and remaining copies are stored on disk. The job is then available to select for printing via the control panel menus or PML. The job will be deleted from the disk when the disk space is needed for another proof and hold job but only after the additional copies have been printed. It will also be deleted when the user sends down another proof and hold job with the same job name, or the user explicitly deletes the job. STORE: The job is not printed immediately but is retained on disk. The job is available to select for printing via the control panel DEFAULT VALUE: OFF The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET USERNAME=<80 bytes> GENERAL DESCRIPTION: Eighty-character user name that is obtained by the driver through some internal method or from user input. If the job stream does not contain a USERNAME the default value will be NO USER NAME. The driver is responsible for determining the size of the printers control panel and sending a string of appropriate length. DEFAULT VALUE: NO USER NAME The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and, INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET JOBNAME=<80 bytes> GENERAL DESCRIPTION: Eighty-character job name that may be generated by the driver or obtained from user input. This value may be used in conjunction with the USERNAME to select a job from the front panel. If the job stream does not contain a JOBNAME, the printer will assume no job name; each subsequent job that is sent down by the same user would replace the users last job on disk. The driver is responsible for determining the size of the printers control panel and sending a string of appropriate length. NOTE: The limit of 80 bytes is a PJL limit. The limit for PML will be 40 bytes. DEFAULT VALUE: NULL STRING The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET HOLDTYPE=PUBLIC|PRIVATE GENERAL DESCRIPTION: This variable specifies the privacy level of the job. PUBLIC: The job does not require a PIN in order to be released for printing. This is the default value. PRIVATE: The job requires a PIN in order to be released for printing. The PIN is specified by the HOLDKEY variable. If the HOLDTYPE is set to PRIVATE, a HOLDKEY value must be specified. If no HOLDKEY is specified, the job will be considered PUBLIC. DEFAULT VALUE: PUBLIC The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. @PJL SET HOLDKEY=4 digits, 0000...9999 GENERAL DESCRIPTION: A 4-digit string, each digit 0-9, that is specified in the job stream and then required to be entered in order to release the job for printing. If a HOLDTYPE is PRIVATE, a HOLDKEY value must be specified. If no HOLDKEY value is specified, a job will be considered PUBLIC. DEFAULT VALUE: NULL STRING The value will be stored in RAM only, not in NVRAM. The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed. The variable will appear in the PJL INFO VARIABLES list. The format for the OID is as follows: 3.4.1.6.x.y <-----> | | | | \ / | job-id in the system / \ PML_JOB_MGNT_ROOT_OID \ job attribute 1..6 x values are 1..6: 1) user-name: user name that is obtained by the driver through some internal method or from user input. 2) job-name: job name may be generated by the driver or obtained from user input. 3) hold: indicates the retention classification of the job. The values indicate whether the job is printed immediately and/or stored. There are 4 options: OFF: The job is printed but not retained on the disk. ON: The job is printed and stored temporarily on the disk. STORE: The job is not printed but stored on the disk. PROOF: One copy of the job is printed and the remaining copies are stored on the disk. 4) holdtype: The variable specifies the security level of the job. PUBLIC: The job does not require a PIN in order to release the job for printing. PRIVATE: The job requires a PIN in order to be released for printing. 5) quantity: number of copies to print. Valid values are 0..999. 6) pin: A 4 digit string, each digit is 0-9, that is specified in the job stream and then required to be entered in order to release the job for printing. y : an unsigned 32-bit number which uniquely identifies the job. The job id for the job remains the same for the job until it is deleted from the held jobs list. For example, the OID below is asking for the user name of the job whose id is 3. The application would issue: OID get 3.4.1.6.1.3 For example, the <getnext> OID values sequence is as follows: OID returned OID getnext 3.4.1.6 3.4.1.6.1.1 getnext 3.4.1.6.1.1 3.4.1.6.1.2 getnext 3.4.1.6.2.1 3.4.1.6.2.2 *** getnext 3.4.1.6.1.6 3.4.1.6.1.7 getnext 3.4.1.6.2.1 3.4.1.6.2.2 getnext 3.4.1.6.5.2828 3.4.1.6.6.1 NOTE: for example above, job id 2828 is the last job in the list of held jobs. *** Also supported is <getnext> on the job attributes: OID returned OID getnext 3.4.1.6.1 3.4.1.6.1.1 getnext 3.4.1.6.6 3.4.1.6.6.1

The job name may be generated by the driver or obtained from user input.

Indicates the retention classification of the job. The values indicate whether the job is printed immediately and/or stored. There are 4 options: OFF: The job is printed but not retained on the disk. ON: The job is printed and stored temporarily on the disk. PROOF: One copy of the job is printed and the remaining copies are stored on the disk. STORE: The job is not printed but stored on the disk.

The variable specifies the security level of the job. PUBLIC: The job does not require a PIN in order to release the job for printing. PRIVATE: The job requires a PIN in order to be released for printing.

Number of copies to print.

A string that is specified in the job stream and then required to be entered in order to release the job for printing. PIN stands for Personal Identification Number. Additional information: Must be a 4 digit string, each digit must be 0..9 or a null string if there is no pin. For security purposes, you can no longer get the value of the PIN.

Instructs the printer to schedule the specified held job for printing with the specified number of copies. The job-id is used to identify which job to print. A held job can also be printed from the control panel. Additional information: Bytes 0-3 is the job id of the job to print. Bytes 4-7 is the number of copies to print. Bytes 8-11 (optional) contain the PIN for a Private job.

Instructs the printer to delete the specified held job from the list. The job-id is used to identify which job to delete. A held job can also be deleted from the control panel. Additional information: Setting this to a value that is not a Held Job on the system or is a Private Held Job returns <ErrUnsupValue>. To delete a private Held Job, you must use the PML object HELD-JOB-PRINT with a quantity of 0 and supply the correct HELD-JOB-PIN with the request. (See HELD-JOB-PRINT)

Sets the maximum number of jobs which can be stored in the held job list. Additional information: Sets the size of the temporary job lists queue.

Enables or disables Job Retention (Job Hold). The valid values are eDisabled and eEnabled. (Specifying an invalid mode causes an <badValue> error to be returned.) When eDisabled is specified all Job Retention (Hold, Proof, Store, PIN Printing) is disabled. When eEnabled is specified, the Job Retention characteristics of a given job are defined by the PJL variable SET HOLD. Additional information: When disabled, held jobs are not removed, but must be explicitly removed through the Control Panel or the PML object HELD-JOB-DELETE.

The number of open files allowed at one time. Opening a file when the maximum number of files are currently open will fail. Additional information: Indicates the number of open files a personality (e.g. PCL or PostScript) is guaranteed to be able to open before the file system runs out of file handles. This object is between 1 and 500. Returns <noSuchName> status if attempting to access this object and there is no storage device is installed.

This object allows the system partition to be written to. It consists of a C structure containing the following fields: typedef struct { ubyte password[8]; ubyte volumenumber; } fs_writeable_system_partition_t; which is described below: Bytes 0 - 7: contain the password Byte 8 : is the volume number Access to this command is controlled by the password. If the password supplied is incorrect the command will fail. The volumenumber is a volume number of an existing system partition. Additional information: Returns <noSuchName> status if attempting to access this object and there is no storage device is installed. Returns <badValue> if the password is incorrect or if the volume requested is not present.

Changes a system partition to be READ-ONLY. The value is the volume number to change. If the volume number specified is NOT a system partition an error is returned. Additional information: Returns <noSuchName> status if attempting to access this object and there is no storage device is installed. Returns <badValue> if the volume requested is not present.

Setting this object causes the specified filename to be deleted, after first validating that the authentication data is correct for the specified user ID. The format for this object is a C structure: typedef struct { sint32 UserId; uint16 AuthenticationDataLen ubyte AuthenticationData[] char Filename[]; } fs_delete_files_t; which is described below: Bytes 0 - 3: contains a user id represented as a multi-byte value that is stored in big-endian format, where the most significant byte occurs first. Bytes 4 - 5 : Length of the Athentication data that follows starting at offset 6. Stored as a multi-byte value that is stored in big-endian format, where the most significant byte occurs first. Bytes 6 - 6+AuthenticationDataLen : a ubyte array containing the Authentication data used to verify access for this operation. Bytes starting at offset (6+AuthenticationDataLen+1): A null terminated character array representing the ASCII file name to be deleted. The length of the string will be limited by the remaining space in the object. This string represents a fully-qualified path name which may specify a filename or a regular expression that may match multiple files (e.g <path>/*.exe). Access to this command is controlled by the UserId and the authentication data. If the UserID or authentication data supplied is incorrect the command will fail. The device POS will specify any limitations to the length of the filename string, what constitutes a correct user ID, what constitutes correct authentication data, and the significance of any return values. Additional information: Setting this object causes the specified filename to be deleted, after first validating that the authentication data is correct for the specified user ID. This object is always present. The format for this object is a C structure: typedef struct { sint32 UserId; uint16 AuthenticationDataLen ubyte AuthenticationData[] char Filename[]; } fs_delete_files_t; Bytes 0 - 3: contains a user id represented as a multi-byte value that is stored in big-endian format, where the most significant byte occurs first. Bytes 4 - 5 : Length of the authentication data that follows starting at offset 6. Stored as a multi-byte value that is stored in big-endian format, where the most significant byte occurs first. Bytes 6 - 6+AuthenticationDataLen : a ubyte array containing the authentication data used to verify access for this operation. Bytes starting at offset (6+AuthenticationDataLen+1): A null terminated character array representing the ASCII file name to be deleted. The length of the string will be limited by the remaining space in the object. This string represents a fully-qualified path name which may specify a filename or a file-type regular expression that may match multiple files (e.g., <path>/*.exe). Access to this command is controlled by the UserId and the authentication data. If the UserID or authentication data supplied is incorrect the command will fail. The device POS will specify any limitations to the length of the filename string, what constitutes a correct user ID, what constitutes correct authentication data, and the significance of any return values.

Setting this object to eInitializing causes file system 2 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 physical mass storage device, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM2-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 1st device.

Setting this object to eInitializing causes file system 3 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 physical mass storage device, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM3-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 2nd device.

Setting this object to eInitializing causes file system 4 to be initialized. Reading this object indicates if the file system is currently being initialized. Additional information: The hrDeviceIndex value for the mass storage device is the same value that is used to index into the FILE-SYSTEM sub-tree. Since this product supports up to 3 physical mass storage devices, and since the hrDeviceIndex for the mass storage devices will start at 2 if the mass storage device is installed, the FILE-SYSTEM4-INITIALIZE-VOLUME object will be the object that allows the mass storage device to be initialized that is the 3rd device.

Contains some sort of time stamp indicating when error 1 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: This item contains the engine page count when the error occurred. If there is currently no error entry for this object, a 0 will be returned. Note that 0 may also be returned when there is a valid error, but a current page count was unavailable. If ERROR1-CODE object also returns 0, then an error has not yet been logged for this object. See ERROR1-CODE for an explanation of the order used for storing errors.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: Returns a device specific error code. If the error code returned is 0, then the printer has not yet logged an error for this object. When the maximum number of errors is reached (30 on LaserJet 4100mfp printers), and a new error occurs, the error in ERROR1-CODE will be replaced by the one in ERROR2-CODE, and so on until the last error object will be given the value of the new error. The error number is returned in the upper 16 bits. If it is 68, 69, 79, or 80, then the sub code is returned in the lower 16 bits (eg. 68 001C, where the subcode is already a hexadecimal value). If the error number is any other number, then the 1st sub code (XX) will be in bits 15-8 and the 2nd sub code (YY) will be in bits 7-0 (eg. 55.04.02) where XX=04 and YY=02). Example: If the error is 68 001A, then the value returned will be 4456474. To break it down: 4456474 = 0x0044001A The upper 16 bits: 0x0044 = 68 The lower 16 bits: 0x001A = 001A Which is the error: 68 001A Example: If the error is 55.04.241, then the error code will be 3605745. To break it down: 3605745 = 0x003704F1 The upper 16 bits: 0x0037 = 55 The upper byte of the lower 16 bits: 0x04 = 04 The lower byte of the lower 16 bits: 0xF1 = 241 Which is the error: 55.04.241

Contains some sort of time stamp indicating when error 2 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 3 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 4 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 5 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 6 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 7 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 8 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 9 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 10 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 11 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 12 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 13 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 14 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 15 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 16 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 17 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 18 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 19 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 20 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 21 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 22 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 23 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 24 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 25 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 26 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 27 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 28 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 29 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 30 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 31 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 32 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 33 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 34 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 35 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 36 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 37 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 38 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 39 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 40 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 41 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 42 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 43 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 44 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 45 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 46 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 47 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 48 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 49 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

Contains some sort of time stamp indicating when error 50 occurred. Example time stamps include the actual time the error occurred (in seconds since Jan. 1, 1970), and the total engine page count. The device POS documents the meaning of the time stamp. Additional information: See ERROR1-TIME-STAMP.

Contains a device specific error code. Each device POS should list what errors are logged to the error log and the meaning of each supported error code value. Additional information: See ERROR1-CODE.

A counter which changes when a mass storage based resource has been added or deleted. Additional information: The value of this counter changes each time the MASS-STORAGE-RESOURCE-CHANGED object is set to eTrue. The value also changes when the mass storage device is initialized. However, the value does not change when a mass storage device is removed and a different mass storage device is installed. Initializing all volumes sets this object back to the factory default value. A reboot sets this object back to the factory devalut value. Returns <noSuchName> status if attempting to access this object and there is no storage device is installed.

Setting to eTrue causes MASS-STORAGE-RESOURCE-CHANGE- COUNTER to be incremented. Additional information: Returns <noSuchName> status if attempting to access this object and there is no storage device is installed.

Array of Berkeley sockets style protocol addresses used to bind RPC to a communications protocol family. Setting an instance of this array object to a zero length binary value disables the transport protocol indicated by that instance. All multi-bytes fields are in network (or big-endian) order. Bytes 1 and 2 indicate the transport protocol. Some of the transport protocol mapping information can be found in RFC 1010 Assigned Numbers. A list of interesting transport protocol number mappings include: Protocol | Number ---------+------- UDP/IP | 17 IPX | 1000 MLC | 4660 Bytes 3 and 4 indicate the address family. The address family uses the same mapping as the BSD sockets address family. A list of interesting address family mappings include: Address Family | Number ---------------+------- Internet | 2 NetWare | 6 MLC | 22136 The format the fifth and following bytes is dependent on the address family. For the Internet address family, bytes 5 and 6 contain the port number, bytes 7 through 10 contain the IP address, and the following eight bytes are unused. For NetWare, bytes 5 through 8 are the network number, bytes 9 through 14 are the node number, and bytes 15 and 16 are the socket number. Additional information: The length of the binary value is zero if the instance of an object in the rpc-bind-protocol-address array is not in use. Returns <noSuchName> status if attempting to access this object and there is no storage device is installed.

An array of Berkeley sockets style protocol addresses that the NFS service has been bound to successful. The format is that same as the array of RPC-BIND-PROTOCOL- ADDRESS of objects. Additional information: Returns <noSuchName> status if attempting to access this object and there is no storage device is installed.

Returns or controls RAM disk support. eOFF turns off the RAM disk functionality. eOn turns on the RAM disk functionality and creates a RAM disk whose size is controlled by the RAM-DISK-SIZE object. eAuto turns on the RAM disk functionality and creates a RAM disk size determined by the printer based on installed options and other memory related settings. Additional information: Returns or controls RAM disk support. eOFF turns off the RAM disk functionality. eAuto turns on the RAM disk functionality and creates a RAM disk size determined by the printer based on the amount of installed memory.

Returns or controls the size of the RAM disk. The device POS specifies the minimum memory requirements. The object MAXIMUM-RAM-DISK-MEMORY specifies the maximum memory available for the RAM disk. Additional information: Returns the size of the RAM disk.

This objects name is misleading. This object does not return the maximum configurable RAM disk size. Instead, it returns the maximum amount of memory, in bytes, that can used to increase the size of the RAM disk. Additional information: This object returns the maximum amount of additional memory that is available for increasing the size of the RAM disk.

Total number of simplex pages printed in this media size. Additional information: The 5 usage (simplex/duplex count, simplex/duplex click charge and paper size total) objects described here and below detail the usage for the printer for each paper size defined in the PCL Implementors Guide and in the Media Size Table in the hpmib.txt. The OID binding is based on the click attribute and paper size. For example: The format for the OID is as follows: 3.4.1.5.x.y <-----> | | | | \ / | paper size / \ PRINTER-CLICK_TOTALS ROOT \ OID click attribute 1..5 x values are 1..5: 1) simplex count 2) simplex click charge 3) duplex count 4) duplex click charge 5) printer or scanner paper size total (i.e. depends if the root OID is referrring to the printer or scanner). y : paper size as defined in the Media Size Table in the hpmib.txt

Charge for each simplex page printed in this media size.

Total number of duplex pages printed in this media size.

Charge for each duplex page printed in this media size. Additional information: The click charges for duplex printed media.

The total charge for pages printed in this media size.

The number of pixels required to completely fill a page of this media size. The device POS will specify the resolution at which this pixel count was calculated. Additional information: The number of pixels required to fill a page of a specific media size. The OID binding is the media size you to query for. Only media sizes which the printer supports will be available.

Total printer charge for all paper sizes printed.

Reports the average toner area coverage of all pages printed over the life of the device. Counts pixels on each page, divides pixel count by pixels possible on a page to give the percentage of coverage, and keeps a rolling average percent weighted by area printed.

The first line of usage instructions for the device user.Appears on Line 1 of the usage page.

The second line of usage instructions for the device user.Appears on Line 1 of the usage page.

The third line of usage instructions for the device user.Appears on Line 1 of the usage page.

The fourth line of usage instructions for the device user.Appears on Line 1 of the usage page.

Total number of simplex pages scanned, for this media size. Additional information: The 5 usage (simplex/duplex count, simplex/duplex click charge and paper size total) objects described here and below detail the usage for the scanner for each paper size defined in the PCL Implementors Guide and in the Media Size Table in the hpmib.txt. The OID binding is based on the click attribute and paper size. For example: The format for the OID is as follows: 3.4.1.5.x.y <-----> | | | | \ / | paper size / \ PRINTER-CLICK_TOTALS ROOT \ OID click attribute 1..5 x values are 1..5: 1) simplex count 2) simplex click charge 3) duplex count 4) duplex click charge 5) printer or scanner paper size total (i.e. depends if the root OID is referrring to the printer or scanner). y : paper size as defined in the Media Size Table in the hpmib.txt The click charge objects are of data type real and have a single digit of precision. Setting these objects to more than a single digit of precision will cause truncation at a single digit, for example, if click charge is set to 15.475 and later retrieved with a get, the value will be 15.400 for this object.

Charge for each simplex page printed in this media size.

Total number of duplex pages scanned, for this media size.

Charge for each duplex page scanned, for this media size.

The total charge for pages scanned, for this media size.

Total scanner charge or cost for all paper sizes scanned.

This object provides information on whether the printer has the ability to communicate the write- status of the firmware download while the download is taking place.

If the design of the firmware-download implementation does not allow PML interaction during the download process, this value provides an estimation of the time where the printer will not be able to engage in PML communication. Additional information: If the design of the firmware-download implementation does not allow PML interaction during the download process, this value provides an estimation of the time where the printer will not be able to engage in PML communication. The calculated time is expected to be 140 secs. However, this time may increase as high as 280 secs as the flash part nears the maximum flash count.

Tells the number of times that firmware has been downloaded to the flash part. Additional information: Tells the number of times that firmware has been downloaded to the flash part. The default value will vary depending on how many times the firmware is rolled before shipping.

Provides the current or last reportable state of the firmware download process. The current state may not necessarily be the current state, but could be the post- mortem state.

Reports the manufacturer specified number of times that firmware can be downloaded to the flash part. A value of -1 means that there is no limit. A value of 0 means that downloading firmware is not permitted by this part. Any other positive integer value corresponds to the number of times that firmware can be downloaded to the flash part. Additional information: Reports the manufacturer specified number of times that firmware can be downloaded to the flash part. A value of -1 means that there is no limit. A value of 0 means that downloading firmware is not permitted by this part. Any other positive integer value corresponds to the number of times that firmware can be downloaded to the flash part. The current maximum write count is 500. This may change as flash technology evolves.

This returns the name of the printer. This should match the name in the header of the upgrade image being sent to the flash part. If the name does not match with the name returned then the image that we are attempting to download does not upgrade the printer firmware. Additional information: This object returns the HP name of the printer. This should match what is in the PJL header of the RFU job Web Jet Admin uses this to ensure the printer is available to be upgraded.

This object will return a string value representing the current revision of firmware that the printer is operating with. This is used to determine if code needs to be upgraded when an firmware bundle comes in, in an upgrade job. Additional information: Web Jet Admin uses the version string that is returned to determine what peices of an RFU bundle need to be upgraded when an RFU job is being built. This objects will return the version string of the printer.

This objects input is a null-terminated string representing a fully-qualified path name for an executable file. This object causes the file to be executed by the OS. Additional information: This objects input is a null-terminated string of two or more whitespace-separated tokens. The first token is a path to a directory to make the current working directory. The second token is a path to an executable file to be executed. Any remaining whitespace-separated tokens are optional and will be passed as parameters to the executable. The paths to the directory and executable can be either PJL style (e.g., 1:\app\example) or UNIX-style (e.g., /hpmnt/dsk_ide1a/app/example). The executable is run in a separate process.

This object provides information on whether the upgradable device has the ability to communicate the write-status of the upgrade while the upgrade is taking place.

If the design of the device upgrade implementation does not allow PML interaction during the download process, this value provides an estimation of the time where the device will not be able to engage in PML communication. The time returned will depend upon what device is attempting to be upgraded.

Tells the number of times that firmware for device X has been downloaded to the flash part. The default value will vary depending on how many times the firmware is rolled before shipping.

Provides the current or last reportable state of the device upgrade process. The current state may not necessarily be the current state, but could be the post-mortem state.

Reports the manufacturer specified number of times that firmware for device X can be downloaded to the flash part. A value of -1 means that there is no limit. A value of 0 means that downloading firmware is not permitted by this part. Any other positive integer value corresponds to the number of times that the firmware for device X can be downloaded to the flash part. The current maximum write count is 500. This may change as flash technology evolves.

This returns the name of the upgradable device. This should match the name in the header of the upgrade image being sent to the flash part. If the name does not match with any of the names returned then the device that we are attempting to upgrade is unavailable for upgrading. Additional information: This object returns the HP name of the printer and the upgradable devices. There is one Name object per upgradable device. This should match what is in the PJL header of the RFU job Web Jet Admin uses this to ensure the printer or device is available to be upgraded.

This object will return a string value representing the current revision of firmware that device X is operating with. This is used to determine if code needs to be upgraded when an firmware bundle comes in, in an upgrade job. Additional information: Web Jet Admin uses the version string that is returned to determine what peices of an RFU bundle need to be upgraded when an RFU job is being built. This internal object will return the current version string of the printer or device that it corresponds to.

Enables or disables the ability to upgrade the firmware associated with any device that is available to be upgraded. This will be set to on or off at the RFU level in that if this mode is on any available device can be upgraded and if this mode is off none of the devices can be upgraded. There is not an individual mode for each device. Trying to set this to a value other than eOn or eOff will cause an UnsupportedValue error to occur.

The amount of time, in seconds, to wait for more print job data to be received before an I/O timeout occurs. The I/O channel being timed is the I/O channel that received the data associated with the current print job. If an I/O timeout occurs, the PDL processing sub-system assumes all the data associated with the current print job has been received, and processes the end of job in an PDL specific manner. The POS specifies the supported values. Additional information: If an I/O timeout occurs,the PDL processing sub-system will consider it an end of job condition only if there is data from another I/O subsystem waiting to be processed. The supported values are 5 to 300 seconds. Setting to a value outside the supported range returns <noError> status and the value will be snapped to the nearest supported value.

Indicates if the device will switch between I/O channels when a job boundary is encountered and print job data is available on another I/O channel.

Returns or changes the maximum parallel I/O port speed, for port 1. This object is only supported if this port is a parallel port. An eSlow setting causes a 10 us busy pulse per received byte of data. An eFast setting causes a 1.5 us busy pulse per received byte of data. In rare cases, setting this value to eFast can cause the parallel port to no longer transfer data reliably. Additional information: When the value of this object is changed, it takes effect immediately. It is recommended that the printer be offline and not in a job when this object is changed.

Returns or changes whether the parallel I/O port supports bidirectional communication for port 1. This object is only supported if this port is a parallel port. Additional information: A get on this object returns the current mode for the parallel port. Setting this object specifies whether or not bidirectional communications will be allowed.

Sets the sharpening coefficient used in scanning and image processing. If the device does not support the given value, then it will select the nearest supported value and return <noError>. The list of supported values should be documented in the device POS.

Total number of sheets that have been fed through the Automatic Document Feed (ADF) accessory. Additional information: The Automatic Document Feed (ADF) count is incremented each time a sheet feeds through the ADF. The value will be updated at the end of every scan job.

Total number of scans performed by a flatbed scanner accessory. Additional information: The count is only incremented when a sheet is scanned on the FLATBED. The return value of this object will reset to the lower multiple of 10 at a power cycle. The value will be updated at the end of every scan job.

This object returns an indication of the type of option installed in DIMM slot 1 of the copy processor board. eEmpty means the device did not detect any option installed in the interface slot. eUnknown means the device doesnt recognize the installed option. eUnSupported means the device recognizes the installed option, but does not support the option. eReadOnlyMemory means the installed option contains ROM Ics. eVolatileRandomAccessMemory means the installed option contains RAM ICs that loose data when the power is turned off. eFlashMemory means that the installed option contains a type of non-volatile RAM that needs to be erased before it can be written. eRamRom means the installed option contains both volatile random access memory and read only memory (combo SIMM/DIMM).

This object returns an indication of the type of option installed in DIMM slot 2 of the copy processor board. eEmpty means the device did not detect any option installed in the interface slot. eUnknown means the device doesnt recognize the installed option. eUnSupported means the device recognizes the installed option, but does not support the option. eReadOnlyMemory means the installed option contains ROM Ics. eVolatileRandomAccessMemory means the installed option contains RAM ICs that loose data when the power is turned off. eFlashMemory means that the installed option contains a type of non-volatile RAM that needs to be erased before it can be written. eRamRom means the installed option contains both volatile random access memory and read only memory (combo SIMM/DIMM).

Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SCANNER_ACCESSORY-DIMM1-TYPE type is eFlashMemory, eVolatileRandomAccessMemory, or eRamRom. For eRamRom only the size of the Ram portion of the DIMM is returned.

Returns an indication of the capacity of the installed option in bytes. This object is not supported unless the SCANNER_ACCESSORY-DIMM2-TYPE type is eFlashMemory, eVolatileRandomAccessMemory, or eRamRom. For eRamRom only the size of the Ram portion of the DIMM is returned.

This item is incremented by 1 for each sheet that is scanned through the ADF in 1-sided scan mode. Additional information: The value will be updated at the end of every scan job.

This item is incremented by 2 for each sheet that is scanned through the ADF in 2-sided scan mode. Additional information: In LaserJet 4100mfp, this value is always 0 because of manual duplexing.

This relates to the number of pages scanned for copying. This item is incremented by 2 for each sheet scanned through the ADF in 2-sided scan mode, and it is incremented by 1 for flatbed scans. Scanning for testing and calibration purposes are NOT TO BE INCLUDED in this count. Additional information: The value will be updated at the end of every scan job.

This relates to the number of pages scanned for fax/send. This item is incremented by 2 for each sheet scanned through the ADF in 2-sided scan mode, and it is incremented by 1 for flatbed scans. Scanning for testing and calibration purposes are NOT TO BE INCLUDED in this count. Additional information: The value will be updated at the end of every scan job.

This relates to the number of copy pages printed on a device. The output sheet that is duplexed (made 2-sided) should be counted as 2 pages. Additional information: The value will be updated at the end of every scan job.

This item sets the URL pointer to the Digital Send Module that is servicing this accessory.

This item is used for detecting the status of the Digital Send component. A bit-mask indicates the status as follows: 0x00 = READY 0x01 = DIGITAL_SEND_GATEWAY_DOWN 0x02 = SMTP_GATEWAY_DOWN 0x04 = LDAP_GATEWAY_DOWN

Contains the default size of the original to be scanned Additional information: Contains the default size of the original to be scanned.

Contains the mix between graphics and text on the scanned page.

Allows user to continue scanning more pages. The UI will prompt user for more pages if job mode is on.

Background level for background removal. Additional information: Background level for background removal.

Select default image quality. Additional information: Which image quality to use.

Contains the default content orientation for a scanned document. Additional information: Contains the default content orientation for a scanned document, i.e., the orientation of the page as the user would read it.

Sets the default heavy media scan mode on or off. Additional information: Sets the default heavy media scan mode to on or off.

Enables (1) or disables (0) the auto resend timeout. Additional information: Enables (2) or disables (1) the DEFAULT-RESET-SEND-TIMEOUT.

Incremented each time the digital sender writes a log entry. Additional information: Trappable object that is incremented each time the digital sender writes a log entry.

Contains the email gateway address. Additional information: Contains the email gateway address.

Contains the LDAP gateway address. Additional information: Contains the ldap gateway address.

Indicates if the digital fax service is available. Additional information: Indicates if digital fax service is available.

Indicates if the analog fax device is available. Additional information: Indicates if the analog fax (Belin) is available.

Indicates whether and why the scanner is not ready. A set bit indicates a problem.

Returns or changes the state of the calibration operation. cScanCalibrationIdle - indicates that calibration is not in progress. cScanCalibrationStart - This state is set by host to request calibration initiation. Device should not set to this state. cScanCalibrationActive - Indicates device is in calibration mode. Device sets cScanCalibrationActive to signal calibration is in process. cScanCalibrationAborted - Set by device to indicate calibration was prematurely terminated. Set by host when a calibration error occurs. cScanCalibrationSendDataRequest - Set by host when host wants to send data to the device. cScanCalibrationSendDataRequestOK - Set by the device to tell the host that the device is ready to accept data. cScanCalibrationSendDataRequestDone -Set by the device to indicate the data was received by the device. cScanCalibrationRequestScanBuffer - Set by the host to request a buffer from the device. cScanCalibrationDone - Set by the host to inform the device calibration is complete. The sequence of bits being set and the restrictions for setting bits should be documented in the device POS.

Error status of the most recent calibration session. eNoError(1) - The calibation was successful. eUnknownCalibrationError(2) - An unknown error occurred. eScannerFeederEmpty(3) - The feeder contained nothing to scan. eLowMemory(4) - Insufficient memory available to complete the calibration. eWriteFailed(5) - Write to NVRAM failure. eScannerBusy(6) - Scanner is busy. Detailed information about the cause and remedy for each error should be documented in the device POS.

Controls or reports how mopies are generated. eOff turns off the mopy feature. eAuto allows the device to determine the best method for generating mopies based on the device configuration. eStandard spools the I/O data and replays the I/O data multiple times to generate the mopies. eEnhanced spools the rasterized page images and replays the rasterized data to generate the mopies. Typically, the rasterized data will be larger and will allow all but the first mopy to print at speed. If the job being mopied is not extremely complex, then the first mopy will print at speed also.

Returns or changes default copies. Default copies is the default values used by the PDL to control the number of copies of each page in the print job that are printed. The print job can override this value. The list of supported values should be documented in the device POS. Additional information: The supported values are 1 through 32000. Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snaps are as follows: <1 snaps to 1 >999 snaps to 32000

Instructs the PDL processing sub-system to finishing processing the current page of the current job. Form feed is also known as close page or eject page. If the PDL processing sub-system is in a FORM-FEED-NEEDED state, this causes the device to flush or finish processing the current page of the current job. If the device is not in the FORM-FEED-NEEDED state, an <genErr> will occur.

Returns or changes the value of the default vertical black resolution. The units are dots per inch. Additional information: In OZ changing this OID also causes DEFAULT-HORIZONTAL-BLACK RESOLUTION to change. DEFAULT-HORIZONTAL-BLACK-RESOLUTION and DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the same. The supported values are: LaserJet 4100mfp: 300, 600, 1200 Viper: 600 Cayenne: 300, 600 Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snap values are as follow: LaserJet 4100mfp: 450 >= n < 900 snaps to 600 n >= 900 snaps to 1200 Viper: n snaps to 600 Cayenne: n < 450 snaps to 300 n >=450 snaps to 600

Returns or changes the value of the default horizontal black resolution. The units are dots per inch. Additional information: In OZ changing this object also causes DEFAULT-VERTICAL-BLACK RESOLUTION to change. DEFAULT-HORIZONTAL-BLACK-RESOLUTION and DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the same. The supported values are: LaserJet 4100mfp: 300, 600, 1200 Viper: 600 Cayenne: 300, 600 Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snap values are as follow: LaserJet 4100mfp: n < 450 snaps to 300 450 >= n < 900 snaps to 600 n >= 900 snaps to 1200 Viper: n snaps to 600 Cayenne: n < 450 snaps to 300 n >=450 snaps to 600

Returns or changes the default page protection behavior. If eOff, the device does not reserve memory for holding the entire raster form of a processed page. If eOn, then memory is reserved. If eAuto, the device determines the amount of memory to reserve. Additional information: Setting to eOn causes MET to be more conservative, but it will not allocate memory to hold an entire rasterized page.

Returns or changes the default number of lines per page. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return the <noError>. Additional information: The supported values in LaserJet 4100mfp are 5 to 128. Setting to an unsupported value causes the the printer to substitute in a snap value and to return <noError> status. The snap values are as follow: <5 snaps to 5 >128 snaps to 128

Returns or changes the default vertical motion index. The unit of measure for VMI is centipoints per line. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return <noError>.

This indicates the default media size. A write of an unsupported value causes an <badValue>. Complete list of supported media sizes along with their dimensions are listed in the Media Size Table near the end of this document.

Returns or sets the media size that is used as the DEFAULT-MEDIA-SIZE when a cold reset occurs.

Returns or sets the media name that is used until the media name is changed by a print job command. Additional information: This string must be one of the MEDIAn-NAME objects. The value of this object is saved across a power cycle.

Returns or changes the reprint (jam recovery) setting. If eOn, then the device will reprint pages jammed pages. If eOff, the device will not attempt to reprint jammed pages. If eAuto, a device dependent algorithm (which should be documented in the POS) will be used to determine if the page gets reprinted. This object controls all PDLs, unless a specific PDL supports its own reprint control mechanism. To date, only PostScript has a PDL reprint control mechanism.

Controls the number of levels used (per pixel) when printing grayscale or color images.

Indicates if the PDL processing sub-system has made marks on the current page and the source subsystem has been idle for a device specific amount of time. Additional information: LaserJet 4100mfp will set this object to eTrue when it has made marks on the current page, the IO-TIMEOUT has expired while PCL was running in `backward-compatibility mode (which is caused by jobs consisting purely of PCL data with no prepended PJL commands), and no data is pending on another I/O. Once it is set to eTrue, more data on the same I/O will cause this object to be set to eFalse, until the above conditions are met again.

Total number of PCL pages printed by the device. Additional information: In LaserJet 4100mfp the PCL page count is kept in NVRAM, and the NVRAM value is updated at least every 10 pages. NOTE: The value returned by this object will be incremented every page but if power is lost between NVRAM updates, up to 9 pages of the page count may be lost. The page count counter will be reset to zero after 16,777,215 (2^24-1) pages. The page count is incremented when a sheet of media is pulled from an input tray. A duplex printed sheet will cause this counter to be incremented by two.

Returns or changes the default PCL height. Height is an approximate measure of the body of the type in centipoints. A centipoint is 1/7200 inch. Height applies only to proportional fonts. Point size, in points, can be converted to font height, in centipoints, by multiplying the point size by 100. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return <noError>. Closest means the smallest absolute difference. Additional information: Supported values range from 400 to 99975, in increments of 25 units. Setting to an unsupported value causes the printer to substitute in a snap value and to return <noError> status. The snap values are as follow: <=400 snaps to 400 >=99975 snaps to 99975 Unsupported values in the range 400 to 99975 snap DOWN to the previous supported value (i.e 25293 snaps to 25275 or 75038 snaps to 75025).

Returns or changes the value of the default font source variable in NVRAM.

Returns or changes the value of the default font number variable in NVRAM. Writing an unsupported value causes the printer to generate an <badValue>. Additional information: Valid numbers or 0 - 255, but only font numbers that are included in the PCL FONT LIST are selectable.

Returns or changes the default PCL font width. Width is expressed as the width of a character in centipoints. A centipoint is 1/7200 inch. Width applies only to fixed space fonts. Pitch, in character per inch, can be converted to font width, in centipoints, by dividing 7200 by the pitch. The POS indicates the supported values. An unsupported value causes the printer to use the closest supported value, causing the printer to return <noError>. Closest means the smallest absolute difference. Additional information: Setting to an unsupported value causes the printer to substitue in a snap value (listed below) and return <noError> status. The snap values for pitch are as follow: <=44 snaps to 44 >=9999 snaps to 9999

Total number of PostScript pages printed by the device. Additional information: This object is only supported if the PostScript option is installed. In LaserJet 4100mfp the count is kept in NVRAM, and the NVRAM value is updated at least every 10 sheets. NOTE: The value returned by this object will be incremented every sheet but if power is lost between NVRAM updates up to 9 sheets of the count may be lost. The counter will be reset to zero after 16,777,215 (2^24-1) pages.

Returns or changes the value of the print PostScript errors setting. If eOn, PostScript prints an error page showing the error encountered and the stack at the time of the error. Additional information: This object is only supported if the PostScript option is installed.

Returns PJL password, if the password is not set (zero). If the password is set, then attempting to retrieve the password causes an <genErr> to occur and will return the <NullValue>.

This object tracks the page count for the pages sent to the print engine for fax jobs. In order to write this object SERVICE-PASSWORD must be set correctly. Additional information: This object tracks the page count for the pages sent to the print engine for fax jobs.

A user-defined password that the Embedded Web Server and Web JetAdmin will use to set the password for configuring the Embedded Web Server on a printer. The device POS will specify any limitation on the size of the password.

A Universal Resource Locator (URL) from which the Embedded Web Server can be configured. Any limitation on the size of this URL will be specified in the device POS.

Each collection bit represents a device or Embedded Web Server feature that can be enabled or disabled via this object.

Sets a string identifying the media name that is to be used in place of the currently requested media. The substitution will continue until another media is selected. If set to a named media that is not currently available the requested media is not overridden. Additional information: When a request is received to print on a size and type of media that is not currently available, this object contains the desired media name as set by the print job. This object should be set to a media name that is currently available in the printer. If a paper mount request is not pending, attempting to get or set this object will cause <noSuchName> to be returned. Setting this object to a string other than one of the MEDIAn-NAME objects (MEDIA-NAMES-AVAILABLE is applied) will cause a status of <badValue> to be returned.

Sets the media size that is to be used in place of the currently requested media size. Additional information: When a request is received to print on a size and type of media that is not currently available, this object contains the desired size as set by the print job. This object should be set to a media size that is currently available to the printer. If a paper mount request is not pending, attempting to get or set this object will cause <noSuchName> to be returned.

Returns or sets the print density setting. Print density is the instantaneous amount of marking agent applied to the paper while printing. A value of zero has the lowest print density, yielding a lighter page. A value of 10 has the highest print density, yielding a darker page. Each POS should document what values in the 0 to 10 range are supported. Additional information: When this value is written, the page pipeline will be flushed (all pages being printed are completed, no new ones are started), the new density setting is set and printing resumes. The acutal change in print density may be gradual over several pages. The supported values are 1 through 5. Setting to an unsupported value causes the printer to substitue in a a snap value and to return <noError> status. The snap values are as follows: <1 snaps to 1 >5 snaps to 5.

Returns or sets the marking agent density setting for each of the marking agents installed. The Marking Agent (aka Print) density is the instantaneous amount of marking agent applied to the media while printing. A value of zero has the lowest print density, yielding a lighter page. A value of 10 has the highest print density, yielding a darker page. The device POS will document what values are supported. Additional information: See the description for PRINT-DENSITY .

When set to eEnabled this object will enable the periodic printing of a page designed to clean the fuser on an EP printing system. The interval between cleaning pages is determied by the setting of the AUTOCLEANING-PAGE-FREQUENCY object and the media size is determined by the AUTOCLEANING-PAGE-SIZE object. This object could also be used in the future to clean the inkjet heads on an inkjet system. Additional information: This will ship disabled for the LaserJet 4100mfp product.

Controls the number of pages between printing of the auto cleaning page (if enabled). Any device specific snap behavior for this page interval will be specified in the device pos. Additional information: For the LaserJet 4100mfp product the legal values are 1000, 2000, 5000, 10000, and 20000. All other values will return OK_or_NEAREST_LEGAL_VALUE_SUBSTITUTED.

Controls the size of paper used to print the auto cleaning page (if enabled). Additional information: For the LaserJet 4100mfp product the legal values are Letter and A4. All other values should return PML_ERROR_INVALID_OR_UNSUPPORTED_VALUE.

Returns or sets the audible feedback function. The default value will be documented in the device POS. Additional information: Turns the audible feedback function on or off

Returns or sets the period of time, specified in milliseconds, to wait before the digital send settings are reset to default values. The default will be specified in the device POS. Additional information: Contains the period, in milliseconds, of inactivity on the control panel before the digital send settings are reset to their default values.

Returns or sets the period of time, specified in milliseconds, to wait before an authentication becomes invalid. The default will be specified in the device POS. Additional information: Contains the period, in milliseconds, of inactivity on the control panel before the authentication becomes invalid.

Total number of sheets of media that have been duplex printed. A sheet is counted if it travels through the duplex page path, regardless of whether or not marks are made on the page. The POS will indicate if the value is kept in NVRAM. Additional information: In LaserJet 4100mfp the count is kept in NVRAM however the NVRAM value is only updated every 10 sheets. NOTE: The value returned by this object will be incremented every sheet but if power is lost between NVRAM updates up to 9 sheets of the count may be lost. The counter will be reset to zero after 16,777,215 (2^24-1) pages.

Print engine revision string. Additional information: The symbol set for this string is Roman-8. Converts engine revision number to a string and returns it.

Returns or changes the value of the multi-purpose (MP) tray configuration variable. The MP tray can be configured to operate as an additional input tray (eCassette), a manual feed slot (eManual), or in a manner compatible with the LaserJet III manual feed slot (eFirst). If configured for eFirst, if media is present in the MP tray, that media is used (assuming the size matches and the print job didnt specify another tray) until the MP tray is empty. Additional information: The MP tray can be configured for use either as a paper cassette or as a priority manual feed tray. When the tray is configured as a manual feed tray, unsolicited status mes sages are not generated when there is no paper in the tray. LaserJet 4100mfp will pull media from TRAY 1 only if there is a sheet present and it matches the needed size and type.

The units of measure used to specify the width and height of the printers default custom paper size. The unit of measure of eTenThousandthsOfInches is 0.0001 inches. Additional information: The units of measure used to specify the width and height of the printers default custom paper size. The unit of measure of eTenThousandthsOfInches is 0.0001 inches.

Sets the printers default custom paper size dimension in the feed direction (direction parallel to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of DEFAULT- CUSTOM-PAPER-DIM-UNIT. The valid range is engine- dependent and should be documented in the POS for each product. Additional information: Sets the printers default custom paper size dimension in the feed direction (direction parallel to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of DEFAULT-CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product.

Sets the printers default custom paper size dimension in the cross-feed direction (direction ninety degrees relative to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of DEFAULT-CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product. Additional information: Sets the printers default custom paper size dimension in the xfeed direction (direction perpendicular to the direction of paper feeding). The value for this object is specified in micrometers or tenthousandths of an inch, depending upon the value of DEFAULT-CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and should be documented in the POS for each product.

The maximum physical media size in the feed direction of this input device expressed in units of measure specified by INPUT-TRAY-MIN-MAX-DIM-UNIT. A value of (-1) implies unlimited, a value of (-2) implies unknown. Additional information: The maximum physical media size in the feed direction of this input device expressed in units of measure specified by PrtInputDimUnit. A value of (-1) implies unlimited, a value of (-2) implies unknown. Refer to Printer Management Standards web page, http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement, for more details in the original format of the Standard Printer MIB.

The maximum physical media size across the feed direction of a particular input device expressed in units of measure specified by INPUT-TRAY-MIN-MAX-DIM-UNIT. A value of (-1) implies unlimited, a value of (-2) implies unknown. Additional information: The maximum physical media size across the feed direction of this input device expressed in units of measure specified by PrtInputDimUnit. A value of (-1) implies unlimited, a value of (-2) implies unknown. Refer to Printer Management Standards web page, http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement, f or more details in the original format of the Standard Printer MIB.

The minimum physical media size in the feed direction of a particular input device expressed in units of measure specified by PrtInputMinMaxDimUnit. A value of (-1) implies unlimited, a value of (-2) implies unknown. Additional information: The minimum physical media size in the feed direction of this input device expressed in units of measure specified by PrtInputDimUnit. A value of (-1) implies unlimited, a value of (-2) implies unknown. Refer to Printer Management Standards web page, http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement, for more details in the original format of the Standard Printer MIB.

The minimum physical media size across the feed direction of a particular input device expressed in units of measure specified by PrtInputMinMaxDimUnit. A value of (-1) implies unlimited, a value of (-2) implies unknown. Additional information: The minimum physical media size across the feed direction of this input device expressed in units of measure specified by PrtInputDimUnit. A value of (-1) implies unlimited, a value of (-2) implies unknown. Refer to Printer Management Standards web page, http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement, for more details in the original format of the Standard Printer MIB.

Returns the media size that is currently configuredconfigured in tray #1. This object can be set to indicate the media size currently loaded, if the printer supports input trays that can not sense the media size. Complete list of supported media sizes along with their dimensions are listed in the Media Size Table near the end of this document.

Provides the number of the Paper Handling Device that contains this input tray. Additional information: The internal trays belong to device 0, which is the base engine. The envelope feeder (if supported) is considered to be device 1 and the external input devices can number between 2 and 6 depending on individual user configurations.

Returns the media size that is currently configured in tray #2. Complete list of supported media sizes along with their dimensions are listed in the Media Size Table near the end of this document. Additional information: If the tray drawer is open, a get on this object will cause a status of <genErr> to be returned. If the tray is empty, the size that the tray is configured for will be returned. If Tray 2 is a 500-sheet standard tray, eJISB5 and eUSExecutive are not valid values.

Provides the number of the Paper Handling Device that contains this input tray.

Returns the media size that is currently configured in tray #3. Complete list of supported media sizes along with their dimensions are listed in the Media Size Table near the end of this document. Additional information: If tray is empty, the size that the tray is configured for will be returned.

Provides the number of the Paper Handling Device that contains this input tray.

Returns the media size that is currently configured in tray #4. Complete list of supported media sizes along with their dimensions are listed in the Media Size Table near the end of this document. Additional information: If the tray drawer is open, a get on this object will cause a status of <genErr> to be returned. If the tray is empty, the size that the tray is configured for will be returned.

Provides the number of the Paper Handling Device that contains this input tray.

Returns the media size that is currently configured in tray #5. Complete list of supported media sizes along with their dimensions are listed in the Media Size Table near the end of this document. Additional information: If the tray drawer is open, a get on this object will cause a status of <genErr> to be returned. If the tray is empty, the size that the tray is configured for will be returned.

Provides the number of the Paper Handling Device that contains this input tray.

Returns the media size that is currently configured in tray #5. Complete list of supported media sizes along with their dimensions are listed in the Media Size Table near the end of this document. Additional information: If the tray drawer is open, a get on this object will cause a status of <genErr> to be returned. If the tray is empty, the size that the tray is configured for will be returned.

Provides the number of the Paper Handling Device that contains this input tray.

Returns the media size that is currently configured in tray #5. Complete list of supported media sizes along with their dimensions are listed in the Media Size Table near the end of this document. Additional information: If the tray drawer is open, a get on this object will cause a status of <genErr> to be returned. If the tray is empty, the size that the tray is configured for will be returned.

Provides the number of the Paper Handling Device that contains this input tray.

Returns or sets the bin that will be used for additional sheets of media when the current bin is full and printing is allowed to continue. Additional information: The data for this object is stored in NVRAM.

Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.

Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.

The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE. Additional information: The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE.

Provides the number of the Paper Handling Device that contains this output bin. Additional information: Provides the number of the Paper Handling Device that contains this output bin.

A device specific description of the last error encountered for output bin 3. Each POS should document the meaning of all supported error information. Additional information: This is a description of the current error state of a finishing device. (ie stapler). If the bin does not support any finishing capabilities then the object will return <badValue>. The possible return values are as follows: Byte1, Byte2, and Byte3 should be 0x00. as they are reserved for future use. Byte4 is a bit field that can be interpreted as follows: bit 0 -- unused bit 1 -- eBinderOut Out of staples bit 2 -- eBinderLimit Too many pages to finish bit 3 -- eBinderJam Staple jammed in stapler bit 4 -- eBinderAlign Pages arent aligned correctly to finish. bit 5 -- unused bit 6 -- unused bit 7 -- unused NOTE: Because HP is marketing a device with a max of 16 bins the OUTBIN-MAXIMUM-BINDING objects are 3-18 but the external device specification requires support of up to 315 output bins. Therefore if these bins exist above 16, then the coresponding objects will also exist OUTBIN19-MAXIMUM-BINDING ... OUTBIN317-MAXIMUM-BINDING

Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.

The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE. Additional information: The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE.

Provides the number of the Paper Handling Device that contains this output bin. Additional information: Provides the number of the Paper Handling Device that contains this output bin.

A device specific description of the last error encountered for output bin 4. Each POS should document the meaning of all supported error information. Additional information: See OUTBIN3-ERROR-INFO DESCRIPTION

Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.

The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE. Additional information: The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE.

Provides the number of the Paper Handling Device that contains this output bin. Additional information: Provides the number of the Paper Handling Device that contains this output bin.

A device specific description of the last error encountered for output bin 5. Each POS should document the meaning of all supported error information. Additional information: See OUTBIN3-ERROR-INFO DESCRIPTION

Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.

The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE. Additional information: The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE.

Provides the number of the Paper Handling Device that contains this output bin. Additional information: Provides the number of the Paper Handling Device that contains this output bin.

A device specific description of the last error encountered for output bin 6. Each POS should document the meaning of all supported error information. Additional information: See OUTBIN3-ERROR-INFO DESCRIPTION

Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.

The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE. Additional information: The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE.

Provides the number of the Paper Handling Device that contains this output bin. Additional information: Provides the number of the Paper Handling Device that contains this output bin.

A device specific description of the last error encountered for output bin 7. Each POS should document the meaning of all supported error information. Additional information: See OUTBIN3-ERROR-INFO DESCRIPTION

Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.

The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE. Additional information: The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE.

Provides the number of the Paper Handling Device that contains this output bin. Additional information: Provides the number of the Paper Handling Device that contains this output bin.

A device specific description of the last error encountered for output bin 8. Each POS should document the meaning of all supported error information. Additional information: See OUTBIN3-ERROR-INFO DESCRIPTION

Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.

The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE. Additional information: The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE.

Provides the number of the Paper Handling Device that contains this output bin. Additional information: Provides the number of the Paper Handling Device that contains this output bin.

A device specific description of the last error encountered for output bin 9. Each POS should document the meaning of all supported error information. Additional information: See OUTBIN3-ERROR-INFO DESCRIPTION

Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.

The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE. Additional information: The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE.

Provides the number of the Paper Handling Device that contains this output bin. Additional information: Provides the number of the Paper Handling Device that contains this output bin.

A device specific description of the last error encountered for output bin 10. Each POS should document the meaning of all supported error information. Additional information: See OUTBIN3-ERROR-INFO DESCRIPTION

Returns or sets the device behavior when this output bin condition causes printing to stop. cCancelJob - The device cancels the job. cOutbinFullOverride - The device sends subsequent media to the overflow bin. cOutbinAttentionOverride - The device ignores the attention condition and continues printing. cBinderAttentionOverride - The device ignores the binder attention condition and continues printing. Additional information: If cCancelJob is set, the current print job will be cancelled regardless of other item settings. If cOutbinFullOverride is set and this bin is the designated overflow bin (OVERFLOW-BIN = 1), then the bit is ignored. This object describes the action that is performed when the JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits are set, no override action is taken (the printer will continue to wait). The action performed by the CONTINUE object being set to eInitiateAction or the GO key being pressed on the control panel may cause different actions. See the CONTINUE object description for information on the actions that occur for those conditions.

The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE. Additional information: The maximum number of sheets of 20 pound paper that can be bound by the binding device that serves this output bin. If a job exceeds this number and the job has requested binding, cBindingError will be set in NOT- READY-DESTINATION-PRINT-ENGINE.

Provides the number of the Paper Handling Device that contains this output bin. Additional information: Provides the number of the Paper Handling Device that contains this output bin.

A device specific description of the last error encountered for output bin 11. Each POS should document the meaning of all supported error information. Additional information: See OUTBIN3-ERROR-INFO DESCRIPTION

Returns or changes how the device processes a low marking agent event. If eCont, then the device continues to print. If eStop, then the device stops until a continue event occurs.

Returns or changes how the device processes an out marking agent event. If eCont, then the device continues to print. If eStop, then the device stops until a continue event occurs.

Returns or changes the Resolution Enhancement Technology setting. Devices that only support eOff and on should map all other values to on and always return the same non-eOff value to indicate on. The list of supported values should be documented in the device POS. Additional information: Setting this object may cause a status of <noError> to be returned, but the new value will not take effect until a job boundary is reached. If a get is done on object before the job boundary is reached, the value last set will be returned. The value of this object is saved over a powercycle. This object exists on monochrome printers only.

Returns or sets the default print quality. A value of zero has the lowest print quality. A value of 100 has the highest print quality. Each POS should document what values in the 0 to 100 range are supported. Additional information: In OZ, the supported values are 0 and 100. A value of zero has the lowest print quality(ECONOMODE=ON), thus minimizes the amount of toner used to print a page. A value of 100 has the highest print quality (ECONOMODE=OFF), thus uses more toner to print a page. Setting to an unsupported value outside of the 0 to 100 range causes the printer to return <badValue> status. Setting to an unsupported value inside of the 0 to 100 range causes the printer to substitute in a snap value (listed below) and to return <noError> status. The snap values are as follow: 0 to 50 snap to 0 51 to 100 snap to 100 This object exists on monochrome printers only.

This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed.

This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed.

This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed.

This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed.

This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed. Additional information: This object is used to send device-specific data to the paper handling device. The meaning of the device- specific command is dependent on the paper handling device and must be specified in the POS. If the paper handling device does not accept the command, then an <badValue> will be returned. If the device accepts the command, it may still be processing the command after the response has been returned. Depending on the device, the application may need to query PHDx-DEVICE-MEMORY to see when the command has completed.

The value of this object controls which of the MEDIAx- NAME objects are supported. If a bit is set to zero, then attempting to get or set the corresponding MEDIAx- NAME objects will return <noSuchName>. Additional information: Setting a bit to one will cause the corresponding MEDIAn- objects to be available (attempting to access an unavailable object will return <noSuchName>). MEDIA1- objects are always present, as this is the default media. If this object is set to a value that does not include cMediaName1Available, that bit will be set and a status of <noError> will be returned. cMediaName12Available, cMediaName13Available, and cMediaName14Available cannot be changed, as MediaName12,13, and 14 are not supported Media Names for LaserJet 4100mfp. Attempts to set these will cause <badValue> to be returned.

Returns or sets the number of 300 dpi dots by which the image is shifted. Shift is relative to the leading edge of the medium as the medium flows through the marking engine with the side to be imaged facing the observer. The leading edge is the North edge and the other edges are defined by the normal compass layout of directions with the compass facing the observer. The adjustment is for all pages printed. A positive value moves the image away from the leading edge of the medium. A negative value moves the image closer to the leading edge of the medium. The value 0 will return the image to its factory default position. Additional information: Returns or sets the number of 300 dpi dots by which the image is shifted. Shift is relative to the leading edge of the medium as the medium flows through the marking engine with the side to be imaged facing the observer. The leading edge is the North edge and the other edges are defined by the normal compass layout of directions with the compass facing the ob server. The adjustment is for all pages printed. A positive value moves the image away from the leading edge of the medium. A negative value moves the image closer to the leading edge of the medium. The value 0 will return the image to its factory default position. The value of this object is stored in NVRAM.

Media 1 name. Additional information: The symbol set for this string is Roman-8.

Length restricted version of the media name 1. The length restriction is required to allow the media name to be displayed on the devices control panel. The device POS must state the maximum number of characters allowed. If the device also has a limitation on what characters in a character set can be used (e.g. only uppercase characters allowed), the POS should also state character restrictions. Additional information: The maximum supported string length is 9 characters. If the user entered string is too long, the device will store the first 9 characters and will return the <noError> status. The characters must be in the range 20H to 7FH except 5C cannot be used. The default symbol set is Roman-8 for English; additional legal symbol sets are ISOLatin5, ISOLatin2 and Windows31J. Setting this object with characters outside of the range or of an illegal symbol set will cause an error status of <badValue> to be returned.

Number of sheets of media 1 that have been printed. The device POS should state whether this value is lost across a power cycle or kept in NVRAM. Additional information: For LaserJet 4100mfp this page count is saved in NVRAM after every 10 pages. The maximum value is 4,294,967,295 which will never be reached in normal operation. The page count is incremented when a sheet of media is pulled from an input tray. A duplex printed sheet will cause this counter to be incremented by one. The data for this object is stored in NVRAM.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: The engine processing characteristics that are to be applied to this media type. Currently, engine processing characteristics denotes changes to fusing temperature and/or transfer roller voltage. The data for this object is stored in NVRAM.

Media 2 name. Additional information: See MEDIA1-NAME.

Length restricted version of the media name 2. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.

Number of sheets of media 2 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 3 name. Additional information: See MEDIA1-NAME.

Length restricted version of the media name 3. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.

Number of sheets of media 3 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 4 name. Additional information: See MEDIA1-NAME.

Length restricted version of the media name 4. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.

Number of sheets of media 4 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 5 name. Additional information: See MEDIA1-NAME.

Length restricted version of the media name 5. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.

Number of sheets of media 5 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 6 name. Additional information: See MEDIA1-NAME.

Length restricted version of the media name 6. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.

Number of sheets of media 6 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 7 name. Additional information: See MEDIA1-NAME.

Length restricted version of the media name 7. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.

Number of sheets of media 7 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 8 name. Additional information: See MEDIA1-NAME.

Length restricted version of the media name 8. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.

Number of sheets of media 8 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 9 name. Additional information: See MEDIA1-NAME.

Length restricted version of the media name 9. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.

Number of sheets of media 9 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 10 name. Additional information: See MEDIA1-NAME.

Length restricted version of the media name 10. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.

Number of sheets of media 10 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 11 name. Additional information: See MEDIA1-NAME.

Length restricted version of the media name 11. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA1-SHORT-NAME.

Number of sheets of media 11 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 15 name. Additional information: The maximum supported string length is 24 bytes. If the user entered string is too long, the device will store the first 24 bytes and return the <noError> status. See CAUTION statement under Product Specific Use.

Length restricted version of the media name 15. See MEDIA1-SHORT-NAME for details. Additional information: The maximum supported string length is 9 characters. If the user entered string is too long, the device will store the first 9 characters and will return the <noError> status. The characters must be in the range 20H to 7FH except 5C cannot be used. The default symbol set is Roman-8 for English; additional legal symbol sets are ISOLatin5, ISOLatin2 and Windows31J. Setting this object with characters outside of the range or of an illegal symbol set will cause an error status of <badValue> to be returned.

Number of sheets of media 15 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA1-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 16 name. Additional information: See MEDIA15-NAME.

Length restricted version of the media name 16. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA15-SHORT-NAME.

Number of sheets of media 16 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA15-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 17 name. Additional information: See MEDIA15-NAME.

Length restricted version of the media name 17. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA15-SHORT-NAME.

Number of sheets of media 17 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA15-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 18 name. Additional information: See MEDIA15-NAME.

Length restricted version of the media name 18. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA15-SHORT-NAME.

Number of sheets of media 18 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA15-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

Media 19 name. Additional information: See MEDIA15-NAME.

Length restricted version of the media name 19. See MEDIA1-SHORT-NAME for details. Additional information: See MEDIA15-SHORT-NAME.

Number of sheets of media 19 that have been printed. See MEDIA1-PAGE-COUNT for details. Additional information: See MEDIA15-PAGE-COUNT.

The engine processing characteristics that are to be applied to this media. The processing characteristics are device specific. Additional information: See the description for MEDIA1-ENGINE-MEDIA-MODE.

The list of engine media modes supported by the device. The modes are each separated by a comma character. An example string would be: Normal,Rough,Low,Vellum.

The number of impressions printed on sheets of this media size. The device POS should state whether this value is lost across a power cycle or is kept in permanent storage. Additional information: The value of this object is persistent across a power cycle. The index for these objects, the last number of the OID, uniquely identifies the paper size. This value corresponds to the page sizes listed below. These values are also documented in the PCL Implementors Guide and the PML Master MIB. 1 US-Executive 2 US-Letter 3 US-Legal 11 eLedger 17 ROC 16K 18 JIS Executive 19 eROC8K 25 ISO and JIS A5 26 ISO and JIS A4 27 ISO and JIS A3 45 JIS B5 46 JIS B4 65 ISO B5 72 eJapanesePostcardDouble 80 Monarch 81 Commercal-10 90 International DL 91 International C5 100 International B5 101 Custom 258 eUSLetterR 282 ISO JISA4R 32767 Unknown Paper Size

Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the first printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. Additional information: Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the first printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. The values in the sub array index are from the media size table in the hpmib. This adjustment is done on a paper size by paper size basis. The standard PCL5 codes for paper size are used for the value used in the OID. Please see S_ARRAY_SUB1 for legal values. The data for this object is stored in NVRAM.

Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the second printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. Additional information: Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). The adjustment is for the second printed side of the medium only. A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. The values in the sub array index are from the media size table in the hpmib. This adjustment is done on a paper size by paper size basis. The standard PCL5 codes for paper size are used for the value used in the OID. Please see S_ARRAY_SUB1 for legal values. The data for this object is stored in NVRAM.

Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. Each OID binding corresponds to a valid tray number for this product. There can be a maximum of 15 trays, a combination of internal and external trays. Products that support other combinations of trays will specify this information in the device pos. The data for this object is stored in NVRAM. Additional information: Returns or sets the number of 300 dpi dots by which the image is shifted relative to the west edge of the medium (see NORTH-EDGE-OFFSET). A positive value moves the image away from the west edge of the medium. A negative value moves the image closer to the west edge of the medium. The value 0 will return the image to its factory default position. Each OID binding corresponds to a valid tray number for this product. There can be a maximum of 15 trays, a combination of internal and external trays. Products that support other combinations of trays will specify this information in the device pos. The data for this object is stored in NVRAM.

This object is used to read the cartridge model number associated with this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the date on which this consumable was manufactured. The format of the string is YYYYMMDD. Where: YYYY is the year. MM is the month (1-12). DD is the day (1-31). Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the serial number for this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the usage units used by the CONSUMABLE-STATUS-TOTAL-CAPACITY object. Additional information: This object will only exist on engines that are E-Label capable, but will exist on these engines regardless of the cartridge being Authentic HP or NonHP. This object can be used to ensure the capability of the E-Label feature for a given engine.

This object is used to report the total capacity of a new consumable of this type. The PML object CONSUMABLE-STATUS-CAPACITY-UNITS can be used to determine the units of measure for this PML object. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to query and set the reseller ID for this consumable. This ID is represented as an integer that is essentially an enumeration representing a specific reseller that sells this consumable. The device POS should detail the mapping of reseller name to reseller ID. In this way the reseller can program into the consumable a suggested reseller which can in turn be mapped to a web page through which a replacement can be purchased. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist. The reseller ID is an integer that must be mapped external to the printer by a host application. The value stored must be specific to an external application.

This object is used to read and write the various status flags supported by this consumable. For LaserJet 4100mfp the collection bits supported include: cMarkedAsReordered - indicates the consumable has been reordered. This is the only bit that can be both read and written. , cTonerLowCondition - indicates a toner low condition has occured. This bit in the collection is read-only to PML. cTonerOutCondition - indicates a toner out condition has occured. This bit in the collection is read-only to PML. cDeveloperLowCondition - indicates a developer low condition has occured. This bit in the collection is read-only to PML. cDeveloperOutCondition - indicates a developer out condition has occured. This bit in the collection is read-only to PML. cDrumLowCondition - indicates a drum low condition has occured. This bit in the collection is read-only to PML. cDrumOutCondition - indicates a drum out condition has occured. This bit in the collection is read-only to PML. cWasteTonerFullCondition - indicates a waste toner full condition has occured. This bit in the collection is read-only to PML. cWasteTonerFullWarningCondition - indicates a waste toner full warning condition has occured. This bit in the collection is read-only to PML. cNewConsumable - indicates the consumable is new and has never been used. This bit in the collection is read-only to PML. cAnyPartLowCondition - indicates that at least one part of this consumable has reached a low condition. This bit in the collection is read-only to PML. cAnyPartOutCondition - indicates that at least one part of this consumable has reached an out condition. This bit in the collection is read-only to PML. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the date on which this consumable was first installed. The format of the string is YYYYMMDD. Where: YYYY is the year. MM is the month (1-12). DD is the day (1-31). The device POS needs to indicate what will be written in the event the printer does not have a real time clock. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist. For printers without internal clocks, the date will always be 20000101.

This object is used to report the date on which this consumable was last used. The format of the string is YYYYMMDD. Where: YYYY is the year. MM is the month (1-12). DD is the day (1-31). The device POS needs to indicate what will be written in the event the printer does not have a real time clock. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist. For printers without internal clocks, the date will always be 20000101.

This object is used to report the number of pages that have been printed by this consumable that are of the specified media size - A3 or Ledger. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the number of pages that have been printed by this consumable that are of the specified media size - Legal. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the number of pages that have been printed by this consumable that are of the specified media size - A4 or Letter. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the number of pages that have been printed by this consumable that are of the specified media size - B5 or Executive. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the number of pages that have been printed by this consumable that are of the specified media size - Envelope. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the number of pages that have been printed by this consumable that are of the specified media size - XY or Other. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the number of jobs that have been printed by this consumable. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the units used to measure the capacity of this consumable. Additional information: This object will only exist on engines that are E-Label capable, but will exist on these engines regardless of the cartridge being Authentic HP or NonHP. This object can be used to ensure the capability of the E-Label feature for a given engine.

This object is used to report the number of usage units that remain in this consumable. The units of measurement used by this object can be obtained by querying the CONSUMABLE-STATUS-USAGE-UNITS object. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the name of the manufacturer of this consumable. The device POS will specify the set of manufacturers that could be returned. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist.

This object is used to report the name of the OEM of this consumable. This object will typically return the string HP. The device POS will specify if other OEM consumables are supported. Additional information: This object will only exist for Authentic HP consumables. If the cartridge is deemed to be NonHP, then this object will not exist. This object should always return HP as the OEM name

This object is used to read and write the URL that can be used to reorder consumables for this device. This URL is set at the factory but can be updated by a reseller or third party. Additional information: The URL can be up to 64 characters long.

This object reports the total number of pages that can be printed before the maintenance kit needs to be replaced.

This object reports the number of pages remaining until the Maintenance Interval is reached.

This object reports the current estimate of the number of usage units that remain before this supply is depleted. An installed supply that cannot report such a number will return a value of -2. It is the reponsibility of the host application to query each supply in order to determine an overall device USAGE-UNITS-REMAINING number - the lowest value returned. The unit of measure for this life estimate is determined by reading the corresponding CONSUMABLE-LIFE- USAGE-UNITS object. Additional information: This object returns the Estimated Number of Pages Remaining for the specified supply. It takes into account both the Toner and the Drum contained within the cartride and reports the lower of the two values.

This object reports current usage units in use by the corresponding CONSUMABLE-LIFE-USAGE-UNITS- REMAINING object. Additional information: This object always responds with eEstimatedPagesRemaining for the the Black Toner cartridge.

When set with the correct integer password value this object is used to enable certain device specific test capabilities. When set with any incorrect integer value, this object is used to disable any device specific features previously enabled by this object. This object will return a response of <noSuchName> whenever an attempt is made to query the object rather than <noSuchName> so as to hide the existence of this object from external host applications. Additional information: The following valid password combinations have been defined: 3276801 - Enable reading of E-Label contents even if non-HP 3276802 - Enable writing to Consumable Counters 3276803 - Enable each of the above mentioned test features.

This object is used to read the average marking agent coverage for a given color plane. It is a real number that represents percentage full and will read from 0 to 100%. This object obsoletes or replaces USAGE-AVERAGE-TONER-COVERAGE which could only be used for black toner coverage information. Additional information: The average percent of toner coverage for a specific color plane. The OID binding is the color plane. Only color planes which the printer supports will be available. This is only available if a hard disk is installed.

This object is used to read the accumulated sum of the percent coverage numbers calculated on a per page basis over the life of the printer. Additional information: The sum of the percent toner coverages for all impressions printed. The OID binding is the color plane. Only color planes which the printer supports will be available.

This object is used to read the accumulated sum of the squares of the percent coverage numbers calculated on a per page basis over the life of the printer. Additional information: The sum of the percent toner coverages squared for all impressions printed. The OID binding is the color plane. Only color planes which the printer supports will be available.

This object is used to read the marking agent units of measure per gram. This is typically a conversion factor for converting pixels of toner to grams. This pixels-per-gram value is used to calculate the estimated number of pages remaining for a given marking agent.

Sets the default copy paper size. The device will scan and format the print data based on the value of this object. The device behavior when the scanned media and/or print media does not match the value of this object should be documented in the device POS. Additional information: Legal paper is only supported on the flatbad scanner and not on the ADF.

Specifies the dither matrix used when performing a copy operation.

Returns or sets the duplex copying mode. Duplex printing is when printing occurs on both sides of a sheet of media. Long edge binding is also called vertical binding or book binding. Short edge binding is also called horizontal binding or calendar binding. eSimplexToSimplex: takes image data from only one side of the original document, and print only on one side of each copy. eSimplexToDuplexLongEdgeBinding: takes image data from only one side of the original document, and print to both sides of each copy. The images are rotated so that if the media is rotated along the axis of the long edge of the media, both images would appear as in the original. eSimplexToDuplexShortEdgeBinding: takes image data from only one side of the original document, and print to both sides of each copy. The images are rotated so that if the media is rotated along the axis of the short edge of the media, both images would appear as in the original. eDuplexToDuplex: takes image data from both sides of the original document, and print on both sides of each copy. eDuplexToSimplexLongEdgeBinding: takes image data from both sides of the original document, and prints to only one side of each copy. The images are rotated so that if the media is rotated along the axis of the long edge of the media, both images would appear as in the original. eDuplexToSimplexShortEdgeBinding: takes image data from both sides of the original document, and prints to only one side of each copy. The images are rotated so that if the media is rotated along the axis of the short edge of the media, both images would appear as in the original. Additional information:

This describes the default input tray to be used. The correspondence between enumerated values and actual trays is device defined (and device dependent). The supported writable enumerated values are device specific.

This describes the default output bin to be used. The correspondence between enumerated values and actual bins is device defined (and device dependent). The supported writable enumerated values are device specific.

The time, in seconds, that the printer will wait before automatically reverting to default copy settings. Additional information: The time, in milliseconds, that the printer will wait before automatically reverting to default copy settings. This value is saved over a powercycle.

This item configures the default copy quantity. Additional information: This value is saved over a powercycle.

This item configures the default for the copy flip- pages-up status.

Selects a special digital copier mode as follows: eNone: This is the normal copy mode, which means none of the special features are in effect. eTwoUp : Scans in 2 pages and produces 2 rotated images on a single output page. eFourUpNOrder : Scans in 4 pages and produces 4 scaled down images on a single output page. Images are placed in top down, left to right order. eFourUpZOrder : Scans in 4 pages and produces 4 scaled down images on a single output page. Images are placed in left to right, top down order.

Selects a page boarder mode as follows : eNone : This is the normal copy mode, which no boarder is drawn. eLine : A simple border box is drawn around each scanned image.

This describes the default setting used to stack the output of a set of copies. eCollate : Copies are stacked 1st page of 1st copy, 2nd page of 1st copy, 3rd page of 1st copy, etc. eUncollate: Copies are stacked 1st page of 1st copy, 1st page of 2nd copy, 1st page of 3rd copy, etc.

This item configures the default Intensity (brightness/contrast) setting. The number of discrete units should be application dependent.

This item configures the default edge-to-edge setting for copy jobs.

When ON, this implements the no-wait scanning feature. Originals are scanned to disk while waiting for the printer to become available. Default is ON.

When ON, a walk-up job will automatically interrupt an already-printing mopy jobat a mopy boundary. Default is OFF.

When ON, this prompts the user whether to interrupt an already-printing copy job when a new copy job is started. Default is OFF.

Controls whether new or pending print jobs can begin while a walk-up user is setting up a job. That is, for copy jobs and scan jobs, when ON this prevents print jobs from starting while a walk-up user is setting up a job. Default is ON.

Prevents non-copy print jobs from starting for specified interval after copy job is completely printed. Defined in seconds. Additional information: Prevents non-copy print jobs from starting for specified interval after copy job is completely printed. Defined in milliseconds.

An indication of how many print data channels the I/O card supports. Additional information: This object is used by the IIO card to tell the peripheral firmware how many logical channels will be used by the card. This object can only be set once per physical channel. If an attempt is made to set it a subsequent time it is ignored and an return code of <ErrorActionCanNotBePerformedNow.is returned. If new firmware is dynamically downloaded to the Blazers Plus card, and if that firmware uses more logical channels, it is necessary to reset the printer.

Identifies the values of prtAlertIndex, prtAlertSeverityLevel, prtAlertGroup, prtAlertGroupIndex, prtAlertLocation, and prtAlertCode for the latest critical evnet in the prtAlertTable. The binary string is defined as following: ------------------------------------------------------ Field | Filed | Description Offset | Length | ------------------------------------------------------ 0 | 4 | the value of prtAlertIndex 4 | 4 | the value of prtAlertSeverityLevel 8 | 4 | the value of prtAlertGroup 12 | 4 | the value of prtAlertGroupIndex 16 | 4 | the value of prtAlertLocation 20 | 4 | the value of prtAlertCode ------------------------------------------------------ Each field is in Big Endian style. Additional information: This object is used to pass alert information from the peripheral to the IIO card. The standard printer MIB contains the following description: printerAlert TRAP-TYPE ENTERPRISE printerV1Alert VARIABLES { prtAlertIndex, prtAlertSeverityLevel, prtAlertGroup, prtAlertGroupIndex, prtAlertLocation, prtAlertCode } DESCRIPTION This trap is sent whenever a critical event is added to the prtAlertTable. In order to provide this information in the trap packet, the IIO card enables traps on channelPrinterAlert. When a critical alert is generated the peripheral fills the appropriate value into this object and sends it to the card. This object is a structure which contains 24 bytes of data. The structure is: struct structAlertInfo { sint32 prtAlertIndex; sint32 prtAlertSeverityLevel; sint32 prtAlertGroup; sint32 prtAlertGroupIndex; sint32 prtAlertLocation; sint32 prtAlertCode; } thisAlertData;

Identifies the type of MIO print data channel. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the type of each of the channels. The type information is passed using the channelType object. Values are then saved by the peripheral and reported when users request the value of prtChannelType.

The version of the protocol used on this MIO print data channel. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the protocol version of each of the channels. The protocol version information is passed using the channelProtocolVersion object. Values are then saved by the peripheral and reported when users request the value of prtChannelProtocolVersion.

The state of this print data channel. The value determines whether control information and print data is allowed through this channel or not. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the state of each of the channels. The state can change from time to time. The state information is passed using the channelState object. Values are saved by the peripheral and reported when users request the value of prtChannelState.

The value of ifIndex which corresponds to this channel. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the value of the IfIndex for each channel. The IfIndex is used as part of MIB-II. The values are saved by the peripheral and reported when users request the value of prtChannelIfIndex.

Sub-unit status is reported in the entries of the principle table in the Group that represents the sub- unit. For sub-units that report a status, there is a status column in the table and the value of this column is always an integer formed in the following way. The SubUnitStatus is an integer that is the sum of 5 distinct values, Availability, Non-Critical, Critical, On-line, and Transitioning. These values are: Availability value Available and Idle 0 000b Available and Standby 2 010b Available and Active 4 100b Available and Busy 6 110b Unavailable and OnRequest 1 001b Unavailable because Broken 3 011b Unknown 5 101b Non-Critical No Non-Critical Alerts 0 Non-Critical Alerts 8 Critical No Critical Alerts 0 Critical Alerts 16 On-Line Intended state is On-Line 0 Intended state is Off-Line 32 Transitioning At intended state 0 Transitioning to intended state 64 Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the status of each of the channels. The status can change from time to time. The status information is passed using the channelStatus object. Values are saved by the peripheral and reported when users request the value of prtChannelStatus.

Auxiliary information to allow a printing application to use the channel for data submission to the printer. An application capable of using a specific PrtChannelType should be able to use the combined information from the prtChannelInformation and other channel and interface group objects to bootstrap its use of the channel. prtChannelInformation is not intended to provide a general channel description, nor to provide information that is available once the channel is in use. The encoding and interpretation of the prtChannelInformation object is specific to channel type. The description of each PrtChannelType enum value for which prtChannelInformation is defined specifies the appropriate encoding and interpretation, including interaction with other objects. For channel types that do not specify a prtChannelInformation value, its value shall be null (0 length). When a new PrtChannelType enumeration value is registered, its accompanying description must specify the encoding and interpretation of the prtChannelInformation value for the channel type. prtChannelInformation semantics for an existing PrtChannelType may be added or amended in the same manner as described in section 2.4.1 for type 2 enumeration values. The prtChannelInformation specifies values for a collection of channel attributes, represented as text according to the following rules: 1. The prtChannelInformation is coded in the NVT ASCII character set. It is not affected by localization. 2. The prtChannelInformation is a list of entries representing the attribute values. Each entry consists of the following items, in order: a. a keyword, composed of alphabetic characters (A- Z, a-z), that identifies a channel attribute, b. an Equals Sign (=) to delimit the keyword, c. a data value, consisting of NVT ASCII graphics characters (codes 32-126), d. a Line Feed character (code 10) to delimit the data value. No other characters shall be present. Keywords are case-sensitive. Conventionally, keywords are capitalized (including each word of a multi-word keyword), and, since they occupy space in the prtChannelInformation, they are kept short. 3. If a channel attribute has multiple values, it is represented by multiple entries with the same keyword, each specifying one value. Otherwise, there shall be at most one entry for each attribute. 4. By default, entries may appear in any order. If there are ordering constraints for particular entries, these must be specified in their definitions. 5. The prtChannelInformation value may represent information that is not normally coded in textual form, or that is coded in a character set other than NVT ASCII. In these cases, whatever symbolic representation is conventionally used for the information should be used for encoding the prtChannelInformation. (For instance, a binary port value might be represented as a decimal number, Unicode would be represented in UTF-8 format.) 6. For each PrtChannelType for which prtChannelInformation entries are defined, the descriptive text associated with the PrtChannelType enumeration value shall specify the following information for each entry: Title: Brief description phrase, e.g.: Port name,Service Name, Keyword: The keyword value, eg: Port, Service Syntax: The encoding of the entry value, if it cannot be directly represented by NVT ASCII, Status: Mandatory, Optional, or Conditionally Mandatory, Multiplicity: Single or Multiple, to indicate whether the entry may be present multiple times, Description: Description of the use of the entry, other information required to complete the definition (e.g.: ordering contstraints, interactions between entries). Applications that interpret prtChannelInformation should ignore unrecognized entries, so they are not affected if new entry types are added. Additional information: After telling the peripheral how many logical channels will be used, the IIO card tells the printer the value of the information value of each of the channels. The information is auxiliary information used in conjunction with the channel Type.

The low order 31 bits of the number of bytes sent from the printer to the host on this logical channel.

The low order 31 bits of the number of bytes received by the printer from the host on this logical channel.

The low order 31 bits of the number of I/O errors which have occured on this logical channel.

The low order 31 bits of the number of print jobs which have been received on this logical channel.

The number of the MIO card associated with this logical channel. If this logical channel is not associated with an MIO card a zero is returned. The value returned for each logical channel is the MIO cards physical slot number. The list of supported values should be documented in the device POS. Additional information: The value returned will be zero for channels 1..3. If an MIOA card is installed, channels 4..10 will return a value of one or two. If an MIOB card is installed, channels 11..17 will return a value of one or two but not the same as channels 4..10. When two IIO cards are installed, the value returned by any channel 4..17 may change after the printer is power cycled.

Counts configuration changes that change the capabilities of a printer, such as the addition/deletion of input/output bins, the addition/deletion of interpreters, or changes in media size. Such changes will often affect the capability of the printer to service certain types of print jobs. Management applications may cache infrequently changed configuration information about sub-units on the printer. This object should be incremented whenever the agent wishes such applications to invalidate that cache and re-download all of this configuration information, thereby signaling a change in the printers configuration. For example, if an input tray that contained paper of different dimensions was added, this counter would be incremented. As an additional example, this counter would not be incremented when an input tray is removed or the level of an input device changes. Additional information: This is a 32 bit counter (unsigned). When it reaches its maximum value, it will roll to zero.

The value of the prtLocalizationIndex corresponding to the current language, country, and character set to be used for localized string values that are identified as being dependent on the value of this object. Note that this object does not apply to localized strings in the prtConsole group or to any object that is not explicitly identified as being localized according to prtGeneralCurrentLocalization. Additional information: The value of this object is saved in NVRAM.

Setting this value to `powerCycleReset, `resetToNVRAM, or `resetToFactoryDefaults will result in the resetting of the printer. When read, this object will always have the value `notResetting(3), and a SET of the value `notResetting shall have no effect on the printer. Some of the defined values are optional. However, every implementation must support at least the values `notResetting and resetToNVRAM. Additional information: Replaces PML USER-NVRAM-RESET and POWER-ON-RESET. The, the following sequence of events occur when this object is set to ePpowerCycleReset, ePresetToNVRAM, or ePresetToFactoryDefaults: 1. Wait until a job boundary. 2. The paper path is flushed. 3. The printer is reset per the request. The printer will respond to PML requests up to this point in time. All settings will make the printer go thru its power-on initialization routines and I/O cards are reset. When this object is set to ePpowerCycleReset or ePresetToNVRAM, the printer performs its power on initialization routines. I/O cards are reset, although NVRAM on the cards is not changed, and all I/O buffers are flushed. This is equivalent to turning the printer off and then on again. Setting this object to ePresetToFactoryDefaults causes the same action as ePpowerCycleReset exept that it also changes all configurable settings back to their factory defaults. It is equivalent to doing a Cold Reset from the control panel while turning on the printer.

The name of the person who is responsible for operating this printer. It is suggested that this string include information that would enable other humans to reach the operator, such as a phone number. As a convention to facilitate automatic notification of the operator by the agent or the network management station, the phone number, fax number or email address should be placed on a separate line starting with ASCII LF (hex 0x0A) and the ASCII text string (without the quotes): phone: , fax: , and email: , respectively. Phone numbers may contain digits, whitespace and parentheses, which shall be ignored. Phone numbers may also include ASCII comma characters(hex 2C) that are used to indicate a two-second pause during the dialing sequence. If either the phone, fax, or email information is not available, then a line should not be included for this information. NOTE: For interoperability purposes, it is advisable to use email addresses formatted according to RFC 822 requirements. Additional information: Replaces PML SYSTEM-CONTACT. The maximum supported string length is 32 characters. Length of 32 was chosen so a phone number could be included with the name. If the user entered string is too long, the device will store as much as possible and will return the <noError> status.

The name of the person responsible for servicing this printer. It is suggested that this string include information that would enable other humans to reach the service person, such as a phone number. As a convention to facilitate automatic notification of the service person by the agent or a network management station, the phone number, fax number or email address should be placed on a separate line starting with ASCII LF (hex 0x0A) and the ASCII text string (without the quotes): phone: , fax: , and email: , respectively. Phone numbers may contain digits, whitespace and parentheses, which shall be ignored. Phone numbers can also include one or more ASCII comma characters(hex 2C) to indicate a two-second pause during the dialing sequence. If either the phone,fax, or email information is not available, then a line should not included for this information. NOTE: For interoperability purposes, it is advisable to use email addresses formatted according to RFC 822 requirements. Additional information: Replaces PML SYSTEM-CONTACT. The maximum supported string length is 32 characters. Length of 32 was chosen so a phone number could be included with the name. If the user entered string is too long, the device will store as much as possible and will return the <noError> status.

The value of prtInputIndex corresponding to the default input sub-unit: that is, this object selects the default source of input media. This value shall be -1 if there is no default input subunit specified for the printer as a whole. In this case, the actual default input subunit may be specified by means outside the scope of this MIB, such as by each interpreter in a printer with multiple interpreters. Additional information: The default input tray is determined by the printer based on DEFAULT-MEDIA-SIZE and DEFAULT-MEDIA-NAME, and whether or not optional trays are installed. If Tray 1 is set in FIRST mode then the size of paper loaded in Tray 1 is assumed to be the requested size. In this case, the printer will pick from Tray 1 without regard to the requested size unless the print jobs paper size, paper type and tray designations exactly match the configuration of another tray; in that case, the requested tray will be picked.

The value of prtOutputIndex corresponding to the default output sub-unit; that is, this object selects the default output destination. This value shall be -1 if there is no default output subunit specified for the printer as a whole. In this case, the actual default output subunit may be specified by means outside the scope of this MIB, such as by each interpreter in a printer with multiple interpreters. Additional information: LaserJet 4100mfp has two output bins in the base product: a face-up bin on the back of the engine and a face-down bin on the top of the engine. These bins are not firmware-selectable; instead, paper is diverted to the face-down bin only if the face-up bin is physically closed. Therefore, these bins are considered together as the standard bin. However, if an HCO is attached to the engine, users will be able to select between an HCO bin and the standard bin, which may be either the face-up or face-down bin, depending upon whether the face-up bin is open. With external output bins attached, the value of this object will be settable from the control panel and by the PJL OUTBIN variable.

The value of prtMarkerIndex corresponding to the default marker sub-unit; that is, this object selects the default marker. Additional information: LaserJet 4100mfp only has one marker subunit.

The value of prtMediaPathIndex corresponding to the default media path; that is, the selection of the default media path. Additional information: If the duplex unit is not installed, the only valid value for this object is 1; with duplex unit installed, 1-3 values are valid. 1 is simplex, 2 is LongEdgeBindingDuplex, and 3 is ShortEdgeBindingDuplex. If the printer is not idle, the new value of this object may not take effect until a job boundary is reached. If a get is done on this object before the job boundary is reached, the value last set will be returned.

The value of the prtLocalizationIndex corresponding to the language, country, and character set to be used for the console. This localization applies both to the actual display on the console as well as the encoding of these console objects in management operations. Additional information: The value of this object is saved in NVRAM. If a localized string is currently being displayed on the control panel by the device, changing this object will cause the displayed string to be changed to its new value. If this object is changed while the printer is processing a page that contains localized strings, the results are undefined.

The number of lines on the printers physical display. This value is 0 if there are no lines on the physical display or if there is no physical display. Additional information: The printer has two physical lines on the display, however, in many cases up to six separate lines of text may be displayed by alternating sets of lines every three seconds. Thus the display really has six logical lines for displaying messages. This object will return the number of logical display lines supported by the printer.

The number of characters per line displayed on the physical display. This value is 0 if there are no lines on the physical display or if there is no physical display.

If the object prtConsoleDisable has value operatorConsoleDisabled then input is not accepted from the operator console. If the object prtConsoleDisable has the value operatorConsoleEnabled then input is accepted from the operator console. If the object prtConsoleDisable has the value operatorConsoleEnabledLevel1,operatorConsoleEnabledLevel2 or operatorConsoleEnabledLevel3 then limited input is accepted from the operator console; the limitations are product specific, however, the limitations are generally less restrictive for operatorConsoleEnabledLevel1 than for operatorConsoleEnabledLeve2, which is less restrictive than operatorConsoleEnabledLevel3. The value of the prtConsoleDisable object is a type-2 enumeration. Additional information: If the object prtConsoleDisable has value ePoperatorConsoleDisabled then manual input is not accepted from the operator console. If the object prtConsoleDisable has the value ePoperatorConsoleEnabled then manual input is accepted from the operator console. The following menus are locked with these corresponding values: ePoperatorConsoleEnabled (no locking) ePoperatorConsoleEnabledLevel1 (minimal locking) RESETS MENU CONFIGURATION MENU I/O MENU ePoperatorConsoleEnabledLevel2 (moderate locking) PRINT QUALITY MENU PAPER HANDLING MENU menus in level 1 ePoperatorConsoleDisabled (maximum locking) PRINTING MENU INFORMATION MENU Job Cancel menus in levels 1 and 2

Used to enable or disable printing a startup page. If enabled, a startup page will be printed shortly after power-up, when the device is ready. Typical startup pages include test patterns and/or printer configuration information.

Used to enable or disable printing banner pages at the beginning of jobs. This is a master switch which applies to all jobs, regardless of interpreter.

An administrator-specified name for this printer. Depending upon implementation of this printer, the value of this object may or may not be same as the value for the MIB-II SysName object. Additional information: The maximum supported string length is 32 characters. Length of 32 was chosen so a phone number could be included with the name. If the user-entered string is too long, the device will store as much as possible and will return the <noError> status. The value of this object is saved over a power cycle.

A recorded serial number for this device that indexes some type device catalog or inventory. This value is usually set by the device manufacturer but the MIB supports the option of writeability for this object for site-specific administration of device inventory or tracking.

A running counter of the number of critical alert events that have been recorded in the alert table. The value of this object is RESET in the event of a power cycle operation (i.e., the value is not persistent. Additional information: This object is set to zero every time the printer is turned on.

A running counter of the total number of alert event entries (critical and non-critical) that have been recorded in the alert table Additional information: This object is set to zero every time the printer is turned on. (It is not persistent through a power-cycle.)

The value of the hrDeviceIndex of the printer device that this storageEntry is associated with. Additional information: Constant. The index value indicates the hrStorageTable index for this storage device. The value indicates the hrDeviceTable index for the printer which uses this storage device. Returns <noSuchName> status if attempting to perform a Get on this OID with no storage device is installed.

The value of the hrDeviceIndex of the printer device that this deviceEntry is associated with. Additional information: Constant. The index indicates the hrDeviceIndex for this mass storage device. The value indicates the hrDeviceIndex for the printer which uses this mass storage device. Returns <noSuchName> status if attempting to perform a Get on this OID with no mass storage device installed.

The manufacturer provided cover sub-mechanism name in the localization specified by prtGeneralCurrentLocalization.

The status of this cover sub-unit. Additional information: Replaces PML NOT-READY-DOOR-OPEN.

A two character language code from ISO 639. Examples en, gb, ca, fr, de. Additional information: The languages supported by LaserJet 4100mfp are English, French, German, Italian, Spanish, Swedish, Danish, Norwegian, Dutch, and Finnish.

A two character country code from ISO 3166, a blank string (two space characters) shall indicate that the country is not defined. Examples: US, FR, DE, ... Additional information: The languages supported by LaserJet 4100mfp (and corresponding country) are English (US, United States), French (FR, France), German (DE, Germany), Italian (IT, Italy), Spanish (ES, Spain), Swedish (SE, Sweden), Danish (DK, Denmark), Norwegian (NO, Norway), Dutch (NL, Netherlands), Finnish (FI, Finland)

The coded character set used for this localization.

The type of technology (discriminated primarily according to feeder mechanism type) employed by the input sub-unit. Note, the Optional Input Class provides for a descriptor field to further qualify the other choice. Additional information: Tray 1 is the multi-purpose tray and is always present. It supports both sheets and envelopes. Its type is ePsheetFeedAutoNonRemovableTray. Tray 2 is a removable tray that comes standard with the printer, although it is usually not removed from the printer. It is of type ePsheetFeedAutoRemovableTray. Trays 3 and 5 in this array are removable trays that can be installed optionally on the printer. They are of type ePsheetFeedAutoRemovableTray. The 4th tray in this array is the envelope feeder. It can be detected even when it is installed while the printer is powered on.

The unit of measurement for use calculating and relaying dimensional values for this input sub-unit. Additional information: Following is a table of paper sizes and dimensions for each paper size supported by LaserJet 4100mfp: Size Inches (ten-thousandths) Millimeters --------------- ------------------------ ----------- eUSExecutive 72500 x 105000 184150 x 266700 eUSLetter 85000 x 110000 215900 x 279400 eUSLegal 85000 x 140000 215900 x 355600 eISOandJISA5 58268 x 82677 148000 x 210000 eISOandJISA4 82677 x 116929 210000 x 297000 eJISB5 71654 x 101181 182000 x 257000 eMonarch 38750 x 75000 98425 x 190500 eCommercial10 41250 x 95000 104775 x 241300 eInternationalDL 43307 x 86614 110000 x 220000 eInternationalC5 63780 x 90157 162000 x 229000 eInternationalB5 69291 x 98425 176000 x 250000 eCustom 85000 x 140000 (max) 215900 x 355600 (max)

This object provides the value of the declared dimension, in the feed direction, of the media that is (or, if empty, was or will be) in this input sub-unit. The feed direction is the direction in which the media is fed on this sub-unit. This dimension is measured in input sub-unit dimensional units (prtInputDimUnit). If this input sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed by management requests. Otherwise, the value may be changed. The value (-1) means other and specifically means that this sub-unit places no restriction on this parameter. The value (-2) indicates unknown. Additional information: For trays 2, 3, and 5 (which can reliably sense this value) these objects behave exactly the same as prtInputMediaDimFeedDirChosen. Attempting to set the objects for tray 2, 3, or 5 will cause <noSuchName> to be returned. The default values assume the trays are configured for letter size paper (or COM10, in the case of the envelope feeder). For tray 1, the value is the dimension for the media size currently declared. For the envelope feeder (tray 4), the value is the dimension for the media size currently declared. Valid values are 0 to 268435455. If a value within 0.2 inches of a standard size (e.g. 85001) is chosen when setting these objects, the standard size will be set for the specified tray if the value of prtInputMediaDimXFeedDirDeclared is also set to within 0.2 inches of the same standard size. If the value is not within 0.2 inches, Custom will be chosen as the size if it is supported by the specified tray, otherwise the first available standard size for the tray will be selected.

This object provides the value of the declared dimension, in the cross feed direction, of the media that is (or, if empty, was or will be) in this input sub-unit. The cross feed direction is ninety degrees relative to the feed direction associated with this sub-unit. This dimension is measured in input sub-unit dimensional units (prtInputDimUnit). If this input sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed by management requests. Otherwise, the value may be changed. The value (-1) means other and specifically means that this sub-unit places no restriction on this parameter. The value (-2) indicates unknown. Additional information: For trays 2, 3, and 5 (which can reliably sense this value) these objects behave exactly the same as prtInputMediaDimXFeedDirChosen. Attempting to set these objects for tray 2, 3, and 5 will cause <noSuchName> to be returned. The default values assume the trays are configured for letter size paper (or COM10, in the case of the envelope feeder). For tray 1 the value is the dimension for the media size currently declared. Valid values are 0 to 268435455. If a value within 0.2 inches of a standard size (e.g. 85001) is chosen when setting these objects, the standard size will be set for the specified tray if the value of prtInputMediaDimFeedDirDeclared is also set to within 0.2 inches of the same standard size. If the value is not within 0.2 inches, Custom will be chosen as the size if it is supported by the specified tray, otherwise the first available standard size for the tray will be selected.

The printer will act as if media of the chosen dimension (in the feed direction) is present in this input source. Note that this value will be used even if the input tray is empty. Feed dimension measurements are taken relative to the feed direction associated with that sub-unit and are in input sub-unit dimensional units (MediaUnit). If the printer supports the declared dimension, the granted dimension is the same as the declared dimension. If not, the granted dimension is set to the closest dimension that the printer supports when the declared dimension is set. The value (-1) means other and specifically indicates that this sub-unit places no restriction on this parameter. The value (-2) indicates unknown. Additional information: The objects for trays 2, 3, and 5 reflect the configuration of the corresponding trays. When the tray is removed, a value of -2 is returned. The default values assume the trays are configured for letter size paper (or COM10, in the case of the envelope feeder). For tray 1 and the envelope feeder, the object returns the value of the media size for which the tray is currently configured because those trays cannot sense what size media they contain.

The printer will act as if media of the chosen dimension (in the cross feed direction) is present in this input source. Note that this value will be used even if the input tray is empty. The cross feed direction is ninety degrees relative to the feed direction associated with this sub-unit. This dimension is measured in input sub-unit dimensional units (MediaUnit). If the printer supports the declared dimension, the granted dimension is the same as the declared dimension. If not, the granted dimension is set to the closest dimension that the printer supports when the declared dimension is set. The value (-1) means other and specifically indicates that this sub-unit places no restriction on this parameter. The value (-2) indicates unknown. Additional information: The objects for trays 2, 3, and 5 reflect the configuration of the corresponding trays. When the tray is removed, a value of -2 is returned. The default values assume the trays are configured for letter size paper (or COM10, in the case of the envelope feeder). The objects for tray 1 and the envelope feeder return the value of the media size for which the tray is currently configured because those trays cannot sense what size media they contain.

The unit of measurement for use in calculating and relaying capacity values for this input sub-unit. Additional information: A sheet is a single piece of 20 pound paper. For tray 4, the envelope feeder, a sheet is one envelope

The maximum capacity of the input sub-unit in input sub-unit capacity units (PrtCapacityUnitTC). There is no convention associated with the media itself so this value reflects claimed capacity. If this input sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed by management requests; otherwise, the value may be written (by a Remote Control Panel or a Management Application). The value (-1) means other and specifically indicates that the sub-unit places no restrictions on this parameter. The value (-2) means unknown. Additional information: Replaces PML TRAYn-MAXIMUM-CAPACITY. This is specified assuming 20 pound paper for the paper trays.

The current capacity of the input sub-unit in input sub-unit capacity units (PrtCapacityUnitTC). If this input sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed by management requests; otherwise, the value may be written (by a Remote Contol Panel or a Management Application). The value (-1) means other and specifically indicates that the sub-unit places no restrictions on this parameter. The value (-2) means unknown. The value (-3) means that the printer knows that at least one unit remains. Additional information: LaserJet 4100mfp can only detect empty/not empty for its trays. It returns -3 for not empty and 0 for empty. If a tray is removed, a value of -2 (unknown) will be returned.

The current status of this input sub-unit. Additional information: Replaces PML STATUS-TRAY-MISSING and STATUS-TRAY-EMPTY. Values returned by the firmware are detailed in the following table. Value Ord Due To Condition indicates that the specified value will be logically ord into the value for this object when the specified Condition occurs. Condition Value Ord Due To Condition ----------------------- ------------------------ Tray Lifter Error 3 Tray not installed or not inserted or not occupied 1 Tray is current source tray and paper is moving 6 Tray involved in paper mount 16 + 32 Value 3 or 1 is Ord in 8 Tray is lifting 64

A description of the media contained in this input sub-unit; This description is intended for display to a human operator. This description is not processed by the printer. It is used to provide information not expressible in terms of the other media attributes (e.g. prtInputMediaDimFeedDirChosen, prtInputMediaDimXFeedDirChosen, prtInputMediaWeight, prtInputMediaType). An example would be `legal tender bond paper. Additional information: Replaces PML TRAYn-MEDIA-NAME. If set to a string other than one contained by a MEDIAn-NAME object, a status of <badValue> is returned. If set to a string that is unsupported for the specified tray object, a status of <badValue> is returned. After Build5.0 (yukon) Cassette trays will not support Transparency nor Label media types. The value of this object is saved across a power cycle.

The name assigned to this input sub-unit. Additional information: Replaces PML TRAYn-NAME.

The vendor name of this input sub-unit.

The model name of this input sub-unit. Additional information: LaserJet 4100mfp does not specify a model name for Tray1 or Tray2, nor for Tray 3 in the 2x250 tray configuration. However, if Tray 3 is installed in the 1x500 configuration, Optional Cassette C4124A will be returned. Tray 3, 4, and 5 objects do not exist unless those trays are installed.

The version of this input sub-unit. Additional information: LaserJet 4100mfp does not specify a version number for the input trays.

The serial number assigned to this input sub-unit. Additional information: LaserJet 4100mfp does not specify a serial number for the input trays.

A free-form text description of this input sub-unit in the localization specified by prtGeneralCurrentLocalization.

Indicates if this input sub-unit has some security associated with it. Additional information: No security mechanism provided.

When the printer is not able to print due to a subunit being empty or the requested media must be manually loaded, the printer will wait for the duration (in seconds) specified by this object. Upon expiration of the timeout, the printer will take the action specified by prtInputNextIndex. The event which causes the printer to enter the waiting state is product specific. If the printer is not waiting for manually fed media, it may switch from an empty subunit to a different subunit without waiting for the timeout to expire. A value of (-1) implies other or infinite which translates to wait forever. The action which causes printing to continue is product specific. A value of (-2) implies unknown. Additional information: This object simply reflects the value of the JOB-INPUT-AUTO-CONTINUE-TIMEOUT object. See the description of that object for additional information.

The value of prtInputIndex corresponding to the input subunit which will be used when this input subunit is emptied and the timeout specified by prtInputMediaLoadTimeout expires. A value of zero(0) indicates that auto input switching will not occur when this input subunit is emptied. If the timeout specified by prtInputLoadMediaTimeout expires and this value is zero(0), the job will be aborted. A value of (-1) means other. The value (-2) means unknown and specifically indicates that an implementation specific method will determine the next input subunit to use at the time this subunit is emptied and the timeout expires. The value(-3) means input switching is not supported for this subunit. Additional information: This object reflects the state of JOB-INPUT-AUTO-CONTINUE-MODE and JOB-INPUT-AUTO-CONTINUE-TIMEOUT. If JOB-INPUT-AUTO-CONTINUE-TIMEOUT is set to -1 or JOB-INPUT-AUTO-CONTINUE-MODE is set up to cancel the job, this object will return 0. If JOB-INPUT-AUTO-CONTINUE-TIMEOUT is >= 0 and JOB-INPUT-AUTO-CONTINUE-MODE is not set up to cancel the job, this object will return -2, meaning that a product-specific tray switching action will occur.