DGS-3710-12C-L2MGMT-MIB: View SNMP OID List / Download MIB

VENDOR: D-LINK


 Home MIB: DGS-3710-12C-L2MGMT-MIB
Download as:   
SNMPv2-SMI, RFC1155-SMI, SW3700PRIMGMT-MIB, DLINK-ID-REC-MIB, SNMPv2-TC

Download standard MIB format if you are planning to load a MIB file into some system (OS, Zabbix, PRTG ...) or view it with a MIB browser. CSV is more suitable for analyzing and viewing OID' and other MIB objects in excel. JSON and YAML formats are usually used in programing even though some systems can use MIB in YAML format (like Logstash).
Keep in mind that standard MIB files can be successfully loaded by systems and programs only if all the required MIB's from the "Imports" section are already loaded.
The tree-like SNMP object navigator requires no explanations because it is very simple to use. And if you stumbled on this MIB from Google note that you can always go back to the home page if you need to perform another MIB or OID lookup.


Object Name OID Type Access Info
 swL2MgmtMIB 1.3.6.1.4.1.171.11.102.1.5.2
     swL2DevMgmt 1.3.6.1.4.1.171.11.102.1.5.2.1
         swL2DevInfo 1.3.6.1.4.1.171.11.102.1.5.2.1.1
             swDevInfoTotalNumOfPort 1.3.6.1.4.1.171.11.102.1.5.2.1.1.1
The number of ports within this switch. This value is the sum of the ports within this switch.
             swDevInfoNumOfPortInUse 1.3.6.1.4.1.171.11.102.1.5.2.1.1.2
The number of ports in this switch connected to the segment or the end stations.
             swDevInfoFrontPanelLedStatus 1.3.6.1.4.1.171.11.102.1.5.2.1.1.4
This object is a set of system LED indications. The first four octets are defined as system LED. The first two octets are currently unused and must be set to zero. The third octet indicates the power LED. The fourth octet indicates the console LED. The fifth LED is RPS (Redundancy Power Supply) LED. The other octets are the logical port LED. Every two bytes are presented to a port. The first byte is presented as the Link/Activity LED. The second byte is presented as the Speed LED. System LED: 01 = fail/error/non existence. 02 = work normal Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second most significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
         swL2DevCtrl 1.3.6.1.4.1.171.11.102.1.5.2.1.2
             swL2DevCtrlStpState 1.3.6.1.4.1.171.11.102.1.5.2.1.2.1
This object can enable or disable the spanning tree algorithm during the runtime of the system.
             swL2DevCtrlIGMPSnooping 1.3.6.1.4.1.171.11.102.1.5.2.1.2.2
This object indicates if the layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.
             swL2DevCtrlSnmpTrapState 1.3.6.1.4.1.171.11.102.1.5.2.1.2.5
This object controls the SNMP trap status.
             swL2DevCtrlCleanAllStatisticCounter 1.3.6.1.4.1.171.11.102.1.5.2.1.2.6
When the object is set to active, all statistical counters will be cleared. If set to normal, no action.
             swL2DevCtrlVlanIdOfFDBTbl 1.3.6.1.4.1.171.11.102.1.5.2.1.2.7
Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT_VLAN_ID of the system.
             swL2MACNotifyState 1.3.6.1.4.1.171.11.102.1.5.2.1.2.8
This object can enable or disable MAC Notification.
             swL2MACNotifyHistorySize 1.3.6.1.4.1.171.11.102.1.5.2.1.2.9
This object indicates the history size of MAC addresses in the MAC Address table. The default value is 1 .
             swL2MACNotifyInterval 1.3.6.1.4.1.171.11.102.1.5.2.1.2.10
This object indicates the time interval, in seconds, which will trigger MAC notification messages.
             swL2DevCtrlTelnet 1.3.6.1.4.1.171.11.102.1.5.2.1.2.14
                   swL2DevCtrlTelnetState 1.3.6.1.4.1.171.11.102.1.5.2.1.2.14.1
This object controls the Telnet status.
                   swL2DevCtrlTelnetTcpPort 1.3.6.1.4.1.171.11.102.1.5.2.1.2.14.2
This object designates TCP ports. When Telnet is disabled, this object is not accessible.
             swL2DevCtrlManagementVlanId 1.3.6.1.4.1.171.11.102.1.5.2.1.2.16
This object controls which previously created VLANs are included in the System IP Interface.
             swL2DevCtrlWeb 1.3.6.1.4.1.171.11.102.1.5.2.1.2.17
                   swL2DevCtrlWebState 1.3.6.1.4.1.171.11.102.1.5.2.1.2.17.1
This object controls the Web status.
                   swL2DevCtrlWebTcpPort 1.3.6.1.4.1.171.11.102.1.5.2.1.2.17.2
This object designates TCP ports. When Web is disabled, this object is not accessible.
             swL2DevCtrlLLDPState 1.3.6.1.4.1.171.11.102.1.5.2.1.2.18
Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
             swL2DevCtrlLLDPForwardMessageState 1.3.6.1.4.1.171.11.102.1.5.2.1.2.19
When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Unit packets will be forwarded.
             swL2DevCtrlIpAutoconfig 1.3.6.1.4.1.171.11.102.1.5.2.1.2.20
This object controls the IP auto configuration state.
             swL2DevCtrlCFM 1.3.6.1.4.1.171.11.102.1.5.2.1.2.21
                   swL2DevCtrlCFMState 1.3.6.1.4.1.171.11.102.1.5.2.1.2.21.1
This object indicates the CFM global state.
                   swL2DevCtrlCFMPortTable 1.3.6.1.4.1.171.11.102.1.5.2.1.2.21.2
A table containing CFM state of speicified ports.
                       swL2DevCtrlCFMPortEntry 1.3.6.1.4.1.171.11.102.1.5.2.1.2.21.2.1
The entry of CFM state on speicified ports.
                           swL2DevCtrlCFMPortIndex 1.3.6.1.4.1.171.11.102.1.5.2.1.2.21.2.1.1
This object indicates the port-num.
                           swL2DevCtrlCFMPortState 1.3.6.1.4.1.171.11.102.1.5.2.1.2.21.2.1.2
This object indicates the CFM state on per-port.
         swL2DevAlarm 1.3.6.1.4.1.171.11.102.1.5.2.1.3
             swL2DevAlarmNewRoot 1.3.6.1.4.1.171.11.102.1.5.2.1.3.1
When the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap.
             swL2DevAlarmTopologyChange 1.3.6.1.4.1.171.11.102.1.5.2.1.3.2
This object determines whether or not to send a trap message when the switch topology changes. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device does not send the trap if this object value is disabled or other.
             swL2DevAlarmLinkChange 1.3.6.1.4.1.171.11.102.1.5.2.1.3.3
This object determines whether or not to send a trap message when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device does not send the trap if this object value is disabled or other.
     swL2VLANMgmt 1.3.6.1.4.1.171.11.102.1.5.2.2
         swL2VlanStaticTable 1.3.6.1.4.1.171.11.102.1.5.2.2.1
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
             swL2VlanStaticEntry 1.3.6.1.4.1.171.11.102.1.5.2.2.1.1
Static information for a VLAN configured into the device by (local or network) management.
                 swL2VlanIndex 1.3.6.1.4.1.171.11.102.1.5.2.2.1.1.1
The VLAN-ID or other identifier referring to this VLAN.
                 swL2VLANAdvertisement 1.3.6.1.4.1.171.11.102.1.5.2.2.1.1.2
This object indicates if the advertisement is active or not.
         swL2PVIDAutoAssignmentState 1.3.6.1.4.1.171.11.102.1.5.2.2.2
This object controls the PVID auto assigment state. If Auto-assign PVID is disabled, PVID can only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change the PVID. If Auto-assign PVID is enabled, the PVID will be changed by PVID or VLAN configuration. When a user configures a port to VLAN Xs untagged membership, this ports PVID will be updated with VLAN X. Using the VLAN list command, PVID is updated as the last item of the VLAN list. When a user removes a port from the untagged membership of the PVIDs VLAN, the ports PVID will be assigned default VLAN.
         swL2VlanPortInfoTable 1.3.6.1.4.1.171.11.102.1.5.2.2.3
A table containing vlan and port role information of each port.
             swL2VlanPortInfoEntry 1.3.6.1.4.1.171.11.102.1.5.2.2.3.1
The table entry of vlan port information.
                 swL2VlanPortInfoPortIndex 1.3.6.1.4.1.171.11.102.1.5.2.2.3.1.1
The port index.
                 swL2VlanPortInfoVid 1.3.6.1.4.1.171.11.102.1.5.2.2.3.1.2
The VLAN-ID assigned to a special port
                 swL2VlanPortInfoPortRole 1.3.6.1.4.1.171.11.102.1.5.2.2.3.1.3
The port role of a special port.when none,it means this port is not belong to the vlan.
         swL2NniGvrpBpduAddress 1.3.6.1.4.1.171.11.102.1.5.2.2.7
Specifies the GVRPs BPDU MAC address of NNI port In Q-in_Q status.
     swL2PortMgmt 1.3.6.1.4.1.171.11.102.1.5.2.3
         swL2PortInfoTable 1.3.6.1.4.1.171.11.102.1.5.2.3.1
A table that contains information about every port.
             swL2PortInfoEntry 1.3.6.1.4.1.171.11.102.1.5.2.3.1.1
A list of information for each port of the device.
                 swL2PortInfoPortIndex 1.3.6.1.4.1.171.11.102.1.5.2.3.1.1.1
This object indicates the modules port number.(1..Max port number in the module)
                 swL2PortInfoMediumType 1.3.6.1.4.1.171.11.102.1.5.2.3.1.1.2
Indicates medium type of the port number.
                 swL2PortInfoUnitID 1.3.6.1.4.1.171.11.102.1.5.2.3.1.1.3
Indicates ID of the unit in the system
                 swL2PortInfoType 1.3.6.1.4.1.171.11.102.1.5.2.3.1.1.4
This object indicates the connector type of this port.
                 swL2PortInfoLinkStatus 1.3.6.1.4.1.171.11.102.1.5.2.3.1.1.5
This object indicates the port link status.
                 swL2PortInfoNwayStatus 1.3.6.1.4.1.171.11.102.1.5.2.3.1.1.6
This object indicates the port speed and duplex mode.
                 swL2PortInfoErrorDisabled 1.3.6.1.4.1.171.11.102.1.5.2.3.1.1.8
This object indicates the blocking type of this port.
         swL2PortCtrlTable 1.3.6.1.4.1.171.11.102.1.5.2.3.2
A table that contains control information about every port.
             swL2PortCtrlEntry 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1
A list of control information for each port of the device.
                 swL2PortCtrlPortIndex 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1.1
This object indicates the modules port number.(1..Max port number in the module)
                 swL2PortCtrlMediumType 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1.2
Indicates medium type of the port number.
                 swL2PortCtrlUnitIndex 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1.3
Indicates ID of the unit in the device
                 swL2PortCtrlAdminState 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1.4
This object decides if the port is enabled or disabled.
                 swL2PortCtrlNwayState 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1.5
Chose the port speed, duplex mode, and N-Way function mode.
                 swL2PortCtrlFlowCtrlState 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1.6
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
                 swL2PortCtrlLearningState 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1.7
This object decides if the port is locked or not.
                 swL2PortCtrlMACNotifyState 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1.8
This object sets each ports MAC notification state.
                 swL2PortCtrlMDIXState 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1.10
This object configures the MDIX setting of the port.
                 swL2PortCtrlEEEState 1.3.6.1.4.1.171.11.102.1.5.2.3.2.1.15
This object indicates the EEE state of special port. Note: If the Medium Type is fiber,the EEE state is always disabled.
         swL2PortCtrlJumboFrame 1.3.6.1.4.1.171.11.102.1.5.2.3.3
This object configures the switchs jumbo frame settings.
         swL2PortCtrlJumboFrameMaxSize 1.3.6.1.4.1.171.11.102.1.5.2.3.4
This object describes how many bytes the max jumbo frame is.
         swL2PortCounterCtrlTable 1.3.6.1.4.1.171.11.102.1.5.2.3.6
A table that used to clear counter information about every port.
             swL2PortCounterCtrlEntry 1.3.6.1.4.1.171.11.102.1.5.2.3.6.1
A list of entry used to clear counter information for each port of the device.
                 swL2PortCounterCtrlPortIndex 1.3.6.1.4.1.171.11.102.1.5.2.3.6.1.1
This object indicates the modules port number.(1..Max port number in the module)
                 swL2PortCounterClearCtrl 1.3.6.1.4.1.171.11.102.1.5.2.3.6.1.2
This object indicates if to clear the counters for each port of the device or not.
         swL2PortErrTable 1.3.6.1.4.1.171.11.102.1.5.2.3.7
A table that contains error information for each port.
             swL2PortErrEntry 1.3.6.1.4.1.171.11.102.1.5.2.3.7.1
A list of information regarding port errors on the device.
                 swL2PortErrPortIndex 1.3.6.1.4.1.171.11.102.1.5.2.3.7.1.1
This object indicates the modules port number.(1..Max port number in the module).
                 swL2PortErrPortState 1.3.6.1.4.1.171.11.102.1.5.2.3.7.1.2
This object indicates the port state is enabled or disabled.
                 swL2PortErrPortConnStatus 1.3.6.1.4.1.171.11.102.1.5.2.3.7.1.3
This object indicates whether the PortStatus is err-disabled or not.
                 swL2PortErrPortReason 1.3.6.1.4.1.171.11.102.1.5.2.3.7.1.4
This object describes if the reason for the port error is STP LBD or Storm control.
         swL2PortDropCounterTable 1.3.6.1.4.1.171.11.102.1.5.2.3.9
A table that contains information for each port drop counter.
             swL2PortDropCounterEntry 1.3.6.1.4.1.171.11.102.1.5.2.3.9.1
A list of information for each port drop counter.
                 swL2PortDropCounterPortIndex 1.3.6.1.4.1.171.11.102.1.5.2.3.9.1.1
This object indicates the modules port number.(1..Max port number in the module)
                 swL2PortIngressBandwidthControlDrops 1.3.6.1.4.1.171.11.102.1.5.2.3.9.1.6
The total number of packets discarded by port ingress bandwidth control.
     swL2DhcpRelayMgmt 1.3.6.1.4.1.171.11.102.1.5.2.8
     swL2TrunkMgmt 1.3.6.1.4.1.171.11.102.1.5.2.9
         swL2TrunkMaxSupportedEntries 1.3.6.1.4.1.171.11.102.1.5.2.9.1
Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
         swL2TrunkCurrentNumEntries 1.3.6.1.4.1.171.11.102.1.5.2.9.2
Current active number of entries in the trunk configuration table.
         swL2TrunkCtrlTable 1.3.6.1.4.1.171.11.102.1.5.2.9.3
This table specifies which ports group a set of ports(up to 8) into a single logical link.
             swL2TrunkCtrlEntry 1.3.6.1.4.1.171.11.102.1.5.2.9.3.1
A list of information that specifies which ports group a set of ports(up to 8) into a single logical link.
                 swL2TrunkIndex 1.3.6.1.4.1.171.11.102.1.5.2.9.3.1.1
The index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.
                 swL2TrunkMasterPort 1.3.6.1.4.1.171.11.102.1.5.2.9.3.1.3
The object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
                 swL2TrunkMember 1.3.6.1.4.1.171.11.102.1.5.2.9.3.1.4
Indicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.
                 swL2TrunkFloodingPort 1.3.6.1.4.1.171.11.102.1.5.2.9.3.1.5
The object indicates the flooding port number of the port trunk entry. The first port of the Trunk group is implicitly configured to be the flooding port.
                 swL2TrunkType 1.3.6.1.4.1.171.11.102.1.5.2.9.3.1.6
This object indicates the type of trunk group. static : is static trunk group lacp : is LACP trunk group .
                 swL2TrunkState 1.3.6.1.4.1.171.11.102.1.5.2.9.3.1.7
This object indicates the status of this entry.
         swL2TrunkAlgorithm 1.3.6.1.4.1.171.11.102.1.5.2.9.4
This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
         swL2TrunkLACPPortTable 1.3.6.1.4.1.171.11.102.1.5.2.9.5
This table specifies which ports group a set of ports(up to 8) into a single logical link.
             swL2TrunkLACPPortEntry 1.3.6.1.4.1.171.11.102.1.5.2.9.5.1
A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
                 swL2TrunkLACPPortIndex 1.3.6.1.4.1.171.11.102.1.5.2.9.5.1.1
The index of logical port LACP.
                 swL2TrunkLACPPortState 1.3.6.1.4.1.171.11.102.1.5.2.9.5.1.2
The state of logical port LACP.
     swL2MirrorMgmt 1.3.6.1.4.1.171.11.102.1.5.2.10
           swL2MirrorLogicTargetPort 1.3.6.1.4.1.171.11.102.1.5.2.10.1
This object indicates which switch port will sniff another port. A trunk port member cannot be configured as a target snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.
           swL2MirrorPortSourceIngress 1.3.6.1.4.1.171.11.102.1.5.2.10.2
This represents the port where ingress packets will be sniffed.
           swL2MirrorPortSourceEgress 1.3.6.1.4.1.171.11.102.1.5.2.10.3
This represents the port where egress packets will be sniffed.
           swL2MirrorPortState 1.3.6.1.4.1.171.11.102.1.5.2.10.4
This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - After writing this value to the object, the corresponding entry will be removed from the table. enabled(3) - This entry resides in the table.
     swL2TrafficSegMgmt 1.3.6.1.4.1.171.11.102.1.5.2.14
           swL2TrafficSegTable 1.3.6.1.4.1.171.11.102.1.5.2.14.1
This table specifies that the port can just forward traffic to the specific port list.
               swL2TrafficSegEntry 1.3.6.1.4.1.171.11.102.1.5.2.14.1.1
A list of information which specifies the port with its traffic forwarding list.
                   swL2TrafficSegPort 1.3.6.1.4.1.171.11.102.1.5.2.14.1.1.1
The port number of the logical port.
                   swL2TrafficSegForwardPorts 1.3.6.1.4.1.171.11.102.1.5.2.14.1.1.2
The port list to which the specific port can forward traffic.
     swL2MulticastFilterMode 1.3.6.1.4.1.171.11.102.1.5.2.17
           swL2MulticastFilterModeVlanTable 1.3.6.1.4.1.171.11.102.1.5.2.17.1
A table that contains information about VLAN multicast filter mode.
               swL2MulticastFilterModeVlanEntry 1.3.6.1.4.1.171.11.102.1.5.2.17.1.1
A list of multicast filter mode information for each VLAN.
                   swL2MulticastFilterVid 1.3.6.1.4.1.171.11.102.1.5.2.17.1.1.1
Indicates VID for each VLAN.
                   swL2MulticastFilterVlanMode 1.3.6.1.4.1.171.11.102.1.5.2.17.1.1.2
Specifies multicast filter mode for each VLAN.
     swL2LoopDetectMgmt 1.3.6.1.4.1.171.11.102.1.5.2.18
           swL2LoopDetectCtrl 1.3.6.1.4.1.171.11.102.1.5.2.18.1
               swL2LoopDetectAdminState 1.3.6.1.4.1.171.11.102.1.5.2.18.1.1
This object indicates the loopback detection status for the system.
               swL2LoopDetectInterval 1.3.6.1.4.1.171.11.102.1.5.2.18.1.2
This object indicates the interval value, the range is from 1 to 32767 seconds.
               swL2LoopDetectRecoverTime 1.3.6.1.4.1.171.11.102.1.5.2.18.1.3
This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
               swL2LoopDetectMode 1.3.6.1.4.1.171.11.102.1.5.2.18.1.4
This object indicates the loopback detection mode for the system.
               swL2LoopDetectTrapMode 1.3.6.1.4.1.171.11.102.1.5.2.18.1.5
This object indicates the loopback detection trap mode for the system.
           swL2LoopDetectPortMgmt 1.3.6.1.4.1.171.11.102.1.5.2.18.2
               swL2LoopDetectPortTable 1.3.6.1.4.1.171.11.102.1.5.2.18.2.1
The table specifies the loopback detection function specified by port.
                   swL2LoopDetectPortEntry 1.3.6.1.4.1.171.11.102.1.5.2.18.2.1.1
The table specifies the loopback detection function specified by port.
                       swL2LoopDetectPortIndex 1.3.6.1.4.1.171.11.102.1.5.2.18.2.1.1.1
This object indicates the modules port number. The range is from 1 to the maximum port number specified in the module
                       swL2LoopDetectPortState 1.3.6.1.4.1.171.11.102.1.5.2.18.2.1.1.2
This object indicates the loopback detection function state on the port.
                       swL2LoopDetectPortLoopVLAN 1.3.6.1.4.1.171.11.102.1.5.2.18.2.1.1.3
This object indicates the VLAN list that has detected a loopback.
                       swL2LoopDetectPortLoopStatus 1.3.6.1.4.1.171.11.102.1.5.2.18.2.1.1.4
This object indicates the port status.
     swL2DhcpLocalRelayMgmt 1.3.6.1.4.1.171.11.102.1.5.2.24
           swL2DhcpLocalRelayState 1.3.6.1.4.1.171.11.102.1.5.2.24.1
This object indicates the status of the DHCP local relay function of the switch.
           swL2DhcpLocalRelayVLANTable 1.3.6.1.4.1.171.11.102.1.5.2.24.2
This table is used to manage the DHCP local relay status for each VLAN.
               swL2DhcpLocalRelayVLANEntry 1.3.6.1.4.1.171.11.102.1.5.2.24.2.1
This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
                   swL2DhcpLocalRelayVLANID 1.3.6.1.4.1.171.11.102.1.5.2.24.2.1.1
This object shows the VIDs of the current VLANS in the switch.
                   swL2DhcpLocalRelayVLANState 1.3.6.1.4.1.171.11.102.1.5.2.24.2.1.2
This object indicates the status of the DHCP relay function of the VLAN.
     swL2SyncEthernetMgmt 1.3.6.1.4.1.171.11.102.1.5.2.30
           swL2SyncEthernetState 1.3.6.1.4.1.171.11.102.1.5.2.30.1
This object indicates the synchronous ethernet state.
           swL2SyncEthernetSourcePort 1.3.6.1.4.1.171.11.102.1.5.2.30.2
This object indicates the port which the synchronous ethernet get the clock from. The port number is the sequential (logical) number which is also applied to the bridge MIB. When set to 0, means not specify any port as source port.
           swL2SyncEthernetSourceClock 1.3.6.1.4.1.171.11.102.1.5.2.30.3
This object indicates the clock use System internal or Synchronous Ethernet with partner get the external clock from which port and etc. system_clock: identify the clock used the CPU clock. sync_e: identify the clock used link partners clock.
     swL2MgmtMIBTraps 1.3.6.1.4.1.171.11.102.1.5.2.100
             swL2Notify 1.3.6.1.4.1.171.11.102.1.5.2.100.1
                 swL2NotifyMgmt 1.3.6.1.4.1.171.11.102.1.5.2.100.1.1
                 swL2NotifyPrefix 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2
                     swL2NotifFirmware 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.0
                         swL2macNotification 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.0.1
This trap indicates the MAC addresses variation in address table .
                         swL2PortLoopOccurred 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.0.3
The trap is sent when a Port loop occurs.
                         swL2PortLoopRestart 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.0.4
The trap is sent when a Port loop restarts after the interval time.
                         swL2VlanLoopOccurred 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.0.5
The trap is sent when a Port with a VID loop occurs.
                         swL2VlanLoopRestart 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.0.6
The trap is sent when a Port with a VID loop restarts after the interval time.
                         swL2DyingGaspPowerLost 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.0.7
OAM dying gasp event occurred on device when the power lost.
                     swl2NotificationBidings 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.1
                         swL2macNotifyInfo 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.1.1
This object indicates the last time reboot information.
                         swL2VlanLoopDetectVID 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.1.3
This object indicates the VID that detected a loopback.
                         swL2DyingGaspMac 1.3.6.1.4.1.171.11.102.1.5.2.100.1.2.1.4
This object indicates the mac address of power-lost device.